Leviton 661F-10W Installation Manual

Download

Page 1

QUIET FAN SPEED CONTROL

ONOFF

ONOFFONOFF

ONOFF

Hot (Black)

Neutral (white)

Fan Speed Control

Red

Black

Neutral

Green

Ground

Red

This wire is used in 3-way installations only. For single pole installations, do not remove this insulating label.

Single Pole or 3-Way

Cat. No. 661F – Ceiling Fan 1.5A

120VAC, 60Hz

INSTALLATION INSTRUCTIONS

WARNINGS:

• TO AVOID FIRE, SHOCK, OR DEATH: TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring or servicing ﬁxture!

• TO AVOID FIRE, SHOCK, OR DEATH: this control is to be used with ceiling fans that are rated 120VAC, total load

1.5 amperes maximum.

• Use and/or install in accordance with appropriate electrical codes and regulations.

CAUTIONS:

• For use on ceiling paddle fans with split-capacitor or shaded pole motors only. Please refer to manufacturer’s

DI-000-0661F-02A

instructions or rating label on the motor to conﬁrm type. Use with any other types of motors or equipment may cause overheating and/or damage to the motors or equipment.

• Use only one (1) Fan Speed Control per load. The switch(es) will turn ON the fan at the speed level selected at the control.

• To avoid overheating and possible damage to this device and other equipment, DO NOT install to control a receptacle, ﬂuorescent lighting, a motor or a transformer-operated appliance other than appropriate ceiling fans

• If you are unsure about any part of these instructions, consult an electrician.

• Use this device with copper or copper clad wire only.

Tools needed to install your Fan Speed Control

Slotted/Philips Screwdriver Electrical Tape Ruler Pliers Pencil Cutters

Installing Control by itself or with other devices

NOTE: There is NO derating

necessary for multi-gang installations of this Fan Speed Control.

Installing your Fan Speed Control

WARNING: TO AVOID FIRE, SHOCK, OR DEATH; TURN

Step 1

OFF POWER at circuit breaker or fuse and test that power is

off before wiring or servicing ﬁxture!

Step 2

Identifying your wiring application (most common):

WARNING: If the wiring in the wall box does not resemble any

of these conﬁgurations, consult an electrician.

Single Pole

1. Line (Hot)

2. Neutral

3. Ground

4. Load

3-Way

1. Line or Load (See note below)

2. Neutral

3. Ground

4. First Traveler – note color

5. Second Traveler – note color

NOTE: For 3-Way applications, note that one of the screw terminals from

the old switch being removed will usually be a different color (Black) or labeled Common. Tag that wire with electrical tape and identify as the common (Line or Load) in both the Fan Speed Control wall box and 3-way switch wall box.

Preparing and connecting wires:

Step 3

• Make sure that the ends of the wires from the wall box are straight (cut if necessary).

• Remove 5/8" (1.6 cm) of insulation from each wire in the wall box (shown).

• For Single-Pole Application, go to Step 4a.

• For 3-Way Application, go to Step 4b.

Single-Pole Wiring Application:

Step 4a

Insert wires

straight then twist clockwise

Electrical Tape

BlackRed

120VAC, 60Hz

Cap with

Wire Connector

Red

Green Ground

Connect wires per WIRING DIAGRAM as follows:

• Green or bare copper wire in wall box to GREEN control lead.

• Line Hot wall box wire to BLACK control lead.

• Load wall box wire to RED control lead.

• Remaining RED control lead should have a label afﬁxed.

DO NOT REMOVE this label in a single pole application. NOTE: If the insulating label is not afﬁxed to the second RED lead

use electrical tape or a wire connector to cover.

Proceed to Step 5.

Line

Cut

(if necessary)

5/8"

Strip gage

Page 2

Step 4b

Hot (Black)

Neutral (white)

AC, 60Hz

3-Way Wiring Application:

Tag

Black

Green

Red

Neutral

Ground

Insert wires

straight then twist clockwise

Electrical Tape

Step 6

WARNING:

Fan Speed Control Mounting:

OFF POWER at circuit breaker or fuse and test that power is off

before wiring or servicing ﬁxture!

TO AVOID FIRE, SHOCK, OR DEATH; TURN

Installation may now be completed by carefully positioning all wires to provide room in wall box for the control. Mount the control into box with mounting screws supplied.

Attach wallplate.

Operation

NOTE: If using the control in a 3-way application, the control will turn

ON at the speed level set on the control's slide bar. The fan can be controlled from either the control or the switch location.

ON:

Push rocker switch "ON"

OFF:

Push rocker switch "OFF"

CHANGING SPEEDS: Move slide bar

- Fan will change speeds.

Slide bar to vary the speed of the fan

Red

Black Screw (common)

Fan Speed Control

BlackRed

Green Ground

120V

Line

3-Way Switch

Connect wires per WIRING DIAGRAM as follows:

• Green or bare copper wire in wall box to GREEN control lead.

• Common (Line hot or Load) wire to BLACK control lead.

• Remove insulating label and connect the ﬁrst traveler wire to the RED control lead.

• Connect the second traveler wire to the remaining RED control lead.

Proceed to Step 5.

Step 5

Testing your Fan Speed Control prior to mounting in the wall box:

• Restore power at circuit breaker or fuse.

• Carefully holding control as shown, slide control lever to highest position. If fan is not ON, press rocker. Fan should turn ON to highest speed level.

If fan does not turn ON, refer

to the TROUBLESHOOTING section.

Step 7

Restore Power:

Restore power at circuit breaker or fuse.

Installation is complete.

Push

ON/OFF

Troubleshooting

• Fan does not turn ON

- Circuit breaker or fuse has tripped.

- Fan has burned out.

- Fan Neutral connection is not wired.

For Technical Assistance Call: 1-800-824-3005 (U.S.A. Only) www.leviton.com

FOR CANADA ONLY

For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton Manufacturing of Canada Ltd to the

attention of the Quality Assurance Department, 165 Hymus Blvd, PointeClaire (Quebec), Canada H9R 1E9 or by telephone at 1 800 405-5320.

DI-000-0661F-02A

Leviton warrants to the original consumer purchaser and not for the beneﬁt of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for ﬁve years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement, at its option. For details visit www.leviton.com or call 1-800-824-3005. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and ﬁtness for

a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and ﬁtness for a particular purpose, is limited to ﬁve years. Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or proﬁts or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.

LIMITED 5 YEAR WARRANTY AND EXCLUSIONS

Page 3

ARTWORK PRINT SPECIFICATIONS

8.5"

11"

2.75"

Part No.

PART NUMBER REV DESCRIPTION

DI-000-0661F-02A

SPECIFICATIONS :

Artwork must be printed at 100% (1:1 scale)

Thickness:

Material:

For manuals - designates cover specifications

40 Lbs

Finish:

Color(s): over

Die Line Key:

Die Cut

1 1

Black

Perforate

Fold Line

MANUAL INTERIORS / BINDERY / FOLD SCHEME :

Body Material:

Thickness:

Bindery

Die cut

Perfect Bind

PROCESS :

Offset Flexo

Other

Line Screen:

Angle:

Resolution:

Fold

Drill

Saddle Stitch

Trim

Color(s): over

DIMENSIONS / FOLD SCHEME / BINDERY DIAGRAM

Die Cut Punch/Drill Hole

Part No.

Spot

CMYK

Spot

CMYK

Instruction Sheet

Kiss Cut

Fold Line

Fonts:

Helvetica

Cellophane

Fonts:

4.25"

Glue

FINAL

COMMENTS :

The information in this document is the exclusive PROPRIETARY property of LEVITON MANUFACTURING COMPANY, INC. It is disclosed with the understanding that acceptance or review by the recipient constitutes an undertaking by the recipient. (1) to hold this information in strict confidence, and (2) not to disclose, duplicate, copy, modify or use the information for any purpose other than that for which disclosed.

FOR LEVITON USE ONLY

J. Tang cc: H. Cai

Released Artwork Format:

PMCQA

E. Krajci

V. LoNigro

Production PDF

Artwork Release Date:

K. Cohen cc: B. Randall

S & A

F. Tse cc: J. Lowe

Other

C. Buttitta

5/21/18

Artwork Print Specification Sheet Rev A12.eps

PlantApprovals:

Mktg Eng

Cust Other

HD0118-5330

PN-ARN: Pilot Rev:ECR Number:

D. Quiles

Artist:

Notes: