Page 1
DI-021-SY481-05AAR2253
WEB VERSION
(58I00-1)
MINI TRANSMITTER
Cat. No. 58A00-1
Installation Instructions
The 58A00-1 Mini Door/Window Transmitter is a mini sized supervised wireless
contact that works with the Leviton 45A00-1 Wireless Receiver.
Powering the 58A00-1
For your added convenience, the 58A00-1 comes with the battery preinstalled.
To activate, hold the 58A00-1 rmly in one hand and pull the plastic tab in the
direction indicated.
Locate Transmitter
Select the location where the 58A00-1 is to be mounted.
NOTE: RF signals can be affected by metal objects, including metal doors
or large mirrors. Such locations should be avoided as they can interfere with
proper operation.
Enrolling the 58A00-1
To enroll the 58A00-1, put the 45A00-1 Wireless Receiver in to Setup mode
and advance to an unused address location. Activate the reed switch by
removing the magnet from the transmitter for 1 second, then replacing it. Refer
to the Installation Instructions for the 45A00-1 for additional information.
WARNINGS AND CAUTIONS
• Read and understand all instructions. Follow all warnings and instructions
marked on the product.
• Do not use this product near water - e.g., near a tub, wash basin, kitchen sink
or laundry tub, in a wet basement, or near a swimming pool.
• Never push objects of any kind into this product through openings, as they may
touch dangerous voltages.
• Never install communications wiring or components during a lightning storm.
• Never install communications components in wet locations unless the
components are designed specically for use in wet locations.
• Never touch uninsulated wires or terminals unless the wiring has been
disconnected at the network interface.
• Use caution when installing or modifying communications wiring or components.
• SAVE THESE INSTRUCTIONS.
Mounting the 58A00-1
Once you have determined the proper location, the 58A00-1 can be
permanently mounted.
NOTE: It is the responsibility of the installer to ensure that the 58A00-1 is
securely mounted in the intended location.
Using Provided Screws:
Remove the back from the transmitter (Figure A). Mount the back housing of
the 58A00-1, using the screws supplied, to the desired location.
Using Adhesive Tape:
Ensure that the surface is clean and dry. Apply the supplied tape to the back
of the 58A00-1, press and hold rmly in the desired location for approximately
10-15 seconds. It can take up to 24 hours for the tape to reach maximum
bonding strength.
Align the magnet with the notched arrow on the 58A00-1 housing.
Mount the magnet a maximum of .4” (1. 8cm) from the 58A00-1 by using the
provided tape or screws. If necessary use the spacers provided. Once the
58A00-1 and magnet are mounted, open and close the window/ door to ensure
that none of the parts interfere with this movement. Only one magnet can be
used for each 58A00-1.
Page 2
WEB VERSION
Tamper Switch
Out of the box the 58A00-1 comes equipped with case tamper detection. If the
case is removed, the 58A00-1 will report a zone tamper to the controller. For
added security the 58A00-1 was designed to provide wall tamper monitoring
as well. Simply replace the short rubber actuator (see Figure C) with the longer
one that is included. With this option, if the case is opened or if the 58A00-1 is
removed from it's location, a tamper will be sent to the controller. It is strongly
recommended that mounting screws be used when using the wall tamper option.
Replacing the Battery
The 58A00-1 requires one Renata CR2450N lithium battery. To replace the
battery, remove the cover as indicated in Figure A. Once cover is removed, the
battery will be visible. To remove battery, insert a athead screwdriver under
the battery and gently twist (see Figure D for details).
FCC Compliance
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should
contact Leviton in writing at Leviton Manufacturing of Canada Ltd to the
attention of the Quality Assurance Department, 165 Hymus Blvd, PointeClaire (Quebec), Canada H9R 1E9 or by telephone at 1 800 405-5320.
Leviton warrants to the original consumer purchaser and not for the
benet of anyone else that products manufactured by Leviton under
the Leviton brand name (“Product”) will be free from defects in material
and workmanship for the time periods indicated below, whichever is
shorter: • OmniPro II and Lumina Pro: three (3) years from installation
or 42 months from manufacture date. • OmniLT, Omni IIe, and Lumina:
two (2) years from installation or 30 months from manufacture date. •
Thermostats, Accessories: two (2) years from installation or 30 months
from manufacture date. • Batteries: Rechargeable batteries in products are
warranted for ninety (90) days from date of purchase. Note: Pr imary (nonrechargeable) batteries shipped in products are not warranted. Products
with Windows® Operating Systems: During the warranty per iod, Leviton
will restore corrupted operating systems to factory default at no charge,
provided that the product has been used as originally intended. Installation
of non-Leviton software or modication of the operating system voids this
warranty. Leviton’s obligation under this Limited Warranty is limited to the
repair or replacement, at Leviton’s option, of Product that fails due to defect
in material or workmanship. Leviton reserves the right to replace product
under this Limited Warranty with new or remanufactured product. Leviton
will not be responsible for labor costs of removal or reinstallation of
Product. The repaired or replaced product is then warranted under the
terms of this Limited Warranty for the remainder of the Limited Warranty
time period or ninety (90) days, whichever is longer. This Limited Warranty
does not cover PC-based software products. Leviton is not responsible
for conditions or applications beyond Leviton’s control. Leviton is
not responsible for issues related to improper installation, including
failure to follow written Installation and operation instructions,
normal wear and tear, catastrophe, fault or negligence of the user
or other problems external to the Product. To view complete warranty
and instructions for returning product, please visit us at www.leviton.com.
Use herein of third party trademarks, service marks, trade names, brand
names and/or product names are for informational purposes only, are/may
be the trademarks of their respective owners; such use is not meant to imply
afliation, sponsorship, or endorsement.
For Technical Assistance Call: 800-824-3005 - www.leviton.com
LEVITON LIMITED WARRANTY
DI-021-SY481-05AAR2253© 2013 Leviton Mfg. Co., Inc.
Loading...