Leviton 57A00-1 Installation Instructions Manual

Download

Page 1

DI-021-SY471-05A

WEB VERSION

(57I00-1)

Vanishing Door/Window Transmitter

Cat. No. 57A00-1

Installation Instructions

WARNINGS AND CAUTIONS

• Read and understand all instructions. Follow all warnings and instructions marked on the product.

• Do not use this product near water - e.g., near a tub, wash basin, kitchen sink or laundry tub, in a wet basement, or near a swimming pool.

• Never push objects of any kind into this product through openings, as they may touch dangerous voltages.

• Battery may explode if mistreated. Do not recharge,

disassemble or dispose of in  re.

• SAVE THESE INSTRUCTIONS.

Notice for users in California - CR Coin Cell Lithium Battery information: This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material – special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate.

Description

The 57A00-1 Vanishing Door/Window Transmitter is a supervised wireless contact that works with the Leviton 45A00-1 Wireless Receiver. It has beveled edges that vanishes into any décor. It also features a bypass button that allows you to manually bypass the transmitter, which automatically restores when the magnet is replaced.

Installing the Battery

The 57A00-1 requires one CR2032 lithium battery. To install the battery, remove the cover as indicated in Figure A.

To remove cover, insert screwdriver here, and gently twist

Once cover is removed, insert the battery with the positive (+) side up as indicated in Figure B.

Tamper Switch

Figure A

Figure B

To remove battery, insert screwdriver here, and twist

Battery (+ side up) PC Board

Locate Transmitter

Select the location where the 57A00-1 is to be mounted.

NOTE: RF signals can be affected by metal objects, including metal doors or large mirrors. Such locations should be avoided as they can interfere with proper operation.

Mounting the 57A00-1

Once you have determined the proper location, the 57A00-1 can be permanently mounted using the supplied adhesive tape.

NOTE: It is the responsibility of the installer to ensure that the 57A00-1 is securely mounted in the intended location.

Using Adhesive Tape

Ensure that the surface is clean and dry. Apply the supplied

tape to the back of the 57A00-1, press and hold  rmly in the

desired location for approximately 10-15 seconds. It can take up to 24 hours for the tape to reach maximum bonding strength.

Mounting the Magnet

Align the magnet with the 3 notches on the 57A00-1 housing. Mount the magnet a maximum of .4” from the 57A00-1 by using the supplied tape.

Enrolling the 57A00-1

To enroll the 57A00-1, put the 45A00-1 Wireless Receiver into Setup mode and advance to an unused address location. Activate the reed switch by removing the magnet from the transmitter for 1 second, then replacing it. Refer to the Installation Instructions for the 45A00-1 for additional information.

Using the Bypass Button

To temporarily bypass the transmitter so that you can open an armed door or window without causing an alarm, press the center of the transmitter and hold for 5 seconds. Once you

remove your  nger, you will notice that the LED behind the

transmitter’s front panel will begin to blink.

While the LED is blinking, the transmitter will not transmit any signals to the receiver (you may open the door or window while the LED is blinking without causing an alarm).

Page 2

Once the LED stops blinking, the next time the magnet is

WEB VERSION

removed from the transmitter (i.e. the door or window is opened), the signal will be transmitted to the receiver.

Notes:

1. When activated, the LED will blink for approximately 7

seconds.

2. If the door or window is open when the LED stops blinking, once the door or window is closed, the transmitter is restored. The next time the door or window is opened, the signal is transmitted.

Tamper Switch

Out of the box the 57A00-1 comes equipped with cover tamper detection. If the cover is removed, the 57A00-1 will report a zone tamper (cover off) to the receiver.

FCC Compliance

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This document and all its contents herein are subject to and protected by international copyright and other intellectual property rights and are the property of Leviton Manufacturing

Use herein of third party trademarks, service marks, trade names, brand names and/or product names are for informational purposes only, are/may be the trademarks of their

respective owners; such use is not meant to imply afliation,

sponsorship, or endorsement.

No part of this document may be reproduced, transmitted or transcribed without the express written permission of Leviton Manufacturing Co., Inc.

FOR CANADA ONLY

For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton

Manufacturing of Canada Ltd to the attention of the Quality Assurance Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone at 1 800 405-5320.

Leviton warrants to the original consumer purchaser and not

for the benet of anyone else that products manufactured

by Leviton under the Leviton brand name (“Product”) will be free from defects in material and workmanship for the time periods indicated below, whichever is shorter: • OmniPro II and Lumina Pro: three (3) years from installation or 42 months from manufacture date. • OmniLT, Omni IIe, and Lumina: two (2) years from installation or 30 months from manufacture date. • Thermostats, Accessories: two (2) years from installation or 30 months from manufacture date. • Batteries: Rechargeable batteries in products are warranted for ninety (90) days from date of purchase. Note: Primary (non-rechargeable) batteries shipped in products are not warranted. Products with Windows® Operating Systems: During the warranty period, Leviton will restore corrupted operating systems to factory default at no charge, provided that the product has been used as originally intended.

Installation of non-Leviton software or modication of the

operating system voids this warranty. Leviton’s obligation under this Limited Warranty is limited to the repair or replacement, at Leviton’s option, of Product that fails due to defect in material or workmanship. Leviton reserves the right to replace product under this Limited Warranty with new or remanufactured product. Leviton will not be responsible

for labor costs of removal or reinstallation of Product.

The repaired or replaced product is then warranted under the terms of this Limited Warranty for the remainder of the Limited Warranty time period or ninety (90) days, whichever is longer. This Limited Warranty does not cover PC-based software products. Leviton is not responsible for conditions

or applications beyond Leviton’s control. Leviton is not responsible for issues related to improper installation, including failure to follow written Installation and operation instructions, normal wear and tear, catastrophe, fault or negligence of the user or other problems external to the Product. To view complete warranty and instructions for returning product, please visit us at www.leviton.com.

LEVITON LIMITED WARRANTY

For Technical Assistance Call: 800-824-3005 - www.leviton.com

DI-021-SY471-05A (57I00-1)