Page 1
DI-022-HL561-05AAR2253
WEB VERSION
(56I00-1)
RECESSED DOOR/WINDOW TRANSMITTER
Cat. No. 56A00-1
Installation Instructions
WARNINGS AND CAUTIONS
• Read and understand all instructions. Follow all warnings and instructions marked on the
product.
• Do not use this product near water - e.g., near a tub, wash basin, kitchen sink or laundry
tub, in a wet basement, or near a swimming pool.
• Never push objects of any kind into this product through openings, as they may touch
dangerous voltages.
• Never install communications wiring or components during a lightning storm.
• Never install communications components in wet locations unless the components are
designed specically for use in wet locations.
• Never touch uninsulated wires or terminals unless the wiring has been disconnected at the
network interface.
• Use caution when installing or modifying communications wiring or components.
• SAVE THESE INSTRUCTIONS.
The 56A00-1 Recessed Door/Window Transmitter is a supervised
wireless contact that can be concealed with a door or window frame
for virtual transparency. It works with the Leviton 45A00-1 Wireless
Receiver and is supplied with a replaceable lithium battery that lasts
for 5 years under normal operation.
OPENING THE 56A00-1
Use a athead screw driver to open the 56A00-1 to change tops or
access the battery (See gure 1).
INSTALL BATTERY
Use care when installing the battery and observe the correct polarity when the
battery is inserted (See Figure 2). Use only Panasonic Lithium CR2 batteries
for replacement. When replacing battery use a athead screw driver to open
the top (See Opening the 56A00-1).
WARNING! Battery may explode if mistreated. Do not recharge,
disassemble or dispose of in fire.
MOUNT TRANSMITTER AND MAGNET
It is important to select the proper placement of the recessed transmitter and
magnet. The transmitter has two separate tops that allow a ush mount or
screw mount in case you accidentally over drill the hole or require extra support to ensure the
transmitter does not move. The magnet does not have a second top with a ange to screw it
into place so you must be extra careful to ensure that the magnet is tightly in place
once installed.
Page 2
Step 1: Install the CR2 battery if you have not already done so
WEB VERSION
(See Install Battery).
Step 2: Write down the serial number printed on the outside of the
56A00-1 case or on the board inside where you place the battery.
Step 3: Select a location on the door or window frame for the 56A00-1
transmitter and magnet to be installed. Use a marker or piece of
clay to mark and ensure that the two holes that you intend to drill
are lined up directly across from each other.
Step 4: Using an 11/16” drill bit, slowly drill the rst hole for the magnet.
The 56A00-1 was specically designed to be slightly larger than
an 11/16” hole so you will need to carefully drill to t by slowly
routing the hole little by little to ensure a snug t.*
Step 5: Drill the mating hole for the transmitter and use either the
standard ush mount cap and insert the transmitter for a snug t
or use the anged cap and use the included screws for mounting
the transmitter to the door or window frame.
* If you accidentally drill the magnet side too big and it is loose, you can
place the transmitter in that position and use the anged cap to screw it into position.
This is only one option
when mounting the
56A00-1. You must
assess the best mounting
method based on the
application.
ENROLLING THE 56A00-1
To enroll the 56A00-1, put the 45A00-1 Wireless Receiver in to Setup mode and advance to an unused
address location. Activate the reed switch by removing the magnet from the transmitter for 1 second,
then replacing it. Refer to the Installation Instructions for the 45A00-1 for additional information.
FCC Compliance
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should contact Leviton in
writing at Leviton Manufacturing of Canada Ltd to the attention of the Quality Assurance
Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone at
1 800 405-5320.
Leviton warrants to the original consumer purchaser and not for the benet of anyone else that products
manufactured by Leviton under the Leviton brand name (“Product”) will be free from defects in material and
workmanship for the time periods indicated below, whichever is shorter : • OmniPro II and Lumina Pro: three
(3) years from installation or 42 months from manufacture date. • OmniLT, Omni IIe, and Lumina: two (2)
years from installation or 30 months from manufacture date. • Thermostats, Accessories: two (2) years from
installation or 30 months from manufacture date. • Batteries: Rechargeable batteries in products are warranted
for ninety (90) days from date of purchase. Note: Primary (non-rechargeable) batteries shipped in products are
not warranted. Products with Windows® Operating Systems: During the warranty period, Leviton will restore
corrupted operating systems to factory default at no charge, provided that the product has been used as originally
intended. Installation of non-Leviton software or modication of the operating system voids this warranty.
Leviton’s obligation under this Limited Warranty is limited to the repair or replacement, at Leviton’s option, of
Product that fails due to defect in material or workmanship. Leviton reserves the right to replace product under
this Limited Warranty with new or remanufactured product. Leviton will not be responsible for labor costs
of removal or reinstallation of Product. The repaired or replaced product is then warranted under the terms
of this Limited Warranty for the remainder of the Limited Warranty time period or ninety (90) days, whichever
is longer. This Limited Warranty does not cover PC-based software products. Leviton is not responsible for
conditions or applications beyond Leviton’s control. Leviton is not responsible for issues related to
improper installation, including failure to follow written Installation and operation instructions, normal
wear and tear, catastrophe, fault or negligence of the user or other problems external to the Product.
To view complete warranty and instructions for returning product, please visit us at www.leviton.com.
LEVITON LIMITED WARRANTY
Use herein of third party trademarks, service marks, trade names, brand names and/or product
names are for informational purposes only, are/may be the trademarks of their respective owners; such use is not meant to imply afliation, sponsorship, or endorsement.
© 2013 Leviton Mfg. Co., Inc.
For Technical Assistance Call: 800-824-3005 - www.leviton.com
DI-022-HL561-05AAR2253
Loading...