Leviton 52120-0M1, 52120-7M3, 52120-0M3, 52120-M2H, 52120-CM3 Panel Mounting Instructions

...
Page 1
Panel Mounting Instructions
For use with Series Cat. Nos. 52000 and 57000
PK-93212-10-02-0B
INSTALLATION
WARNING AND CAUTIONS:
• TO BE INSTALLED AND/OR USED IN ACCORDANCE WITH ELECTRICAL CODES AND REGULATIONS.
IF YOU ARE NOT SURE ABOUT ANY PART OF THESE INSTRUCTIONS, CONSULT AN ELECTRICIAN.
PACKAGING INCLUDES: One (1) flush mount bracket and six (6) screws.
BEFORE WIRING!
1. Flush Mounting (Figs. 1, 2 & 3): a. Fit mounting bracket over panel as shown in Fig. 1.
b. Align panel top with non-flanged side of mounting bracket. Insert screws (provided) into mounting bracket threaded screw holes. Firmly tighten screws
until mounting bracket is secured to panel as shown in Fig. 2.
c. Mount to surface using mounting screws (not provided) as shown in Fig. 3.
FLUSH MOUNTING
ENGLISH
Fig. 1 Fig. 2
Surface Mounting (Figs. 4, 5 & 6): a. From the inside of the panel, punch out the four puncture holes located at the corners of the panel’s bottom, as shown in Fig. 4.
b. Insert screws (not provided) as shown in Fig. 5 and firmly tighten to mount to surface as shown in Fig. 6.
SURFACE MOUNTING
Fig. 3
Fig. 6Fig. 4 Fig. 5
2. Restore power at circuit breaker or fuse after wiring. Installation is complete.
Panel mounting brackets are suitable for the following Leviton Surge Protection devices only
52120-0M1 52120-0M2 52120-0M3 52120-7M3 52120-M2H 52120-CM2 52120-CM3 52120-7C3
For Technical Assistance Call: 1-800-824-3005 (U.S.A. Only) www.leviton.com
52240-DM3 52277-0M3 52277-7M3 52277-CM3 52277-7C3 52347-0M3 52412-DS3 52480-DM3
57120-0M3 57120-CM3 57240-DM3 57277-0M3 57277-CM3 57346-0M3 57480-DM3 57600-DM3
Page 2
Directives de montage sur panneau
Pour les modèles des séries 52000 et 57000
INSTALLATION
AVERTISSEMENTS ET MISES EN GARDE:
• INSTALLER OU UTILISER CONFORMÉMENT AUX CODES DE L’ÉLECTRICITÉ EN VIGUEUR.
À DÉFAUT DE BIEN COMPRENDRE LES DIRECTIVES SUIVANTES, EN TOUT OU EN PARTIE, ON DOIT FAIRE APPEL À UN ÉLECTRICIEN.
CETTE TROUSSE COMPREND : Un (1) support de montage encastré et six (6) vis.
INSTALLATION AVERTISSEMENT : POUR ÉVITER LES RISQUES D’INCENDIE, DE CHOC ÉLECTRIQUE OU D’ÉLECTROCUTION, COUPER LE COURANT AU FUSIBLE OU AU
DISJONCTEUR ET S’ASSURER QUE LE CIRCUIT SOIT BIEN COUPÉ AVANT DE PROCÉDER À L’INSTALLATION.
1. Montage encastré (fig. 1 à 3) a. Placer le support de montage sur le panneau de la manière fig. en 1. b. Aligner les orifices du panneau avec ceux du côté sans rebords du support de montage. Insérer les vis fournies dans ces orifices. Serrer fermement les vis jusqu’à ce que le
support soit solidement fixé au panneau (fig. 2). c. Fixer le tout à la surface d’installation au moyen de vis de montage (non fournies), tel que montré à fig. 3. Montage en saillie (fig. 4 à 6) a. Aligner les orifices du support de montage avec ceux du panneau, tel que montré à fig. 4. b. Insérer les vis fournies dans ces orifices et les serrer fermement jusqu’à ce que le support soit solidement fixé au panneau (fig. 5).
2. Rétablir le courant au fusible ou au disjoncteur; l’installation est terminée.
FRANÇAIS
Les support de montage sur panneau conviennent exclusivement aux dispositifs limiteurs de surtensions suivants de Leviton
52120-0M1 52120-0M2 52120-0M3
52120-7M3 52120-M2H 52120-CM2
52120-CM3 52120-7C3 52240-DM3
Ligne d’Assistance Technique : 1 800 405-5320 (Canada seulement) www.leviton.com
52277-0M3 52277-7M3 52277-CM3
52277-7C3 52347-0M3 52412-DS3
52480-DM3 57120-0M3 57120-CM3
57240-DM3 57277-0M3 57277-CM3
57346-0M3 57480-DM3 57600-DM3
Instrucciones para Montar un Panel
Para uso con las series Nos. de Cat. 52000 y 57000
INSTALACION
ESPAÑOL
ADVERTENCIAS Y PRECAUCIONES:
• PARA INSTALARSE Y/O USARSE DE ACUERDO CON LOS CODIGOS ELECTRICOS Y NORMAS APROPIADOS.
• SI USTED NO ESTA SEGURO ACERCA DE ALGUNA DE LAS PARTES DE ESTAS INSTRUCCIONES, CONSULTE A UN ELECTRICISTA.
EL PAQUETTE INCLUYE: Una (1) ménsula para montaje empotrado y seis (6) tornillos. PARA INSTALAR
ADVERTENCIA: PARA EVITAR DESCARGA ELECTRICA, FUEGO, O MUERTE, INTERRUMPA EL PASO DE ENERGIA MEDIANTE EL INTERRUPTOR DE CIRCUITO O
FUSIBLE. ¡ASEGURESE QUE EL CIRCUITO NO ESTE ENERGIZADO ANTES DE INICIAR LA INSTALACION!
1. Montaje Empotrado (Figs. 1-3): a. Encaje la ménsula encima de panel como se muestra en la Fig. 1. b. Alinie la parte superior del panel con el lado sin brida de la ménsula de montaje. Inserte los tornillos (provistos) dentro de los orificios de la ménsula. Apriete firmemente los
tornillos hasta que la ménsula de montaje esté asegurada al panel como se muestra en la Fig. 2 c. Móntelo en la superficie usando tornillos (no provistos) como se muestra en la Fig. 3 Montaje Superficial (Figs. 4-6) a. Desde adentro del panel, empuje los orificios marcados ubicados en las esquinas de la base del panel, como se muestra en la Fig. 4. b. Inserte los tornillos (no proveidos) como se muestra en la Fig. 5 y aprietelos firmemente para montar la superficie, como se muestra en la Fig. 6.
2. Restablezca la energía con el interruptor de circuitos o fusible. La instalación está completa.
Las Ménsulas para Montaje de Panel son sólo adecuadas para los siguientes productos de Protección de Picos de Tensión de Leviton
52120-0M1 52120-0M2 52120-0M3
MONTAGE ENCASTRÉ / MONTAJE EMPOTRADO MONTAGE EN SAILLIE / MONTAJE SUPERFICIAL
52120-7M3 52120-M2H 52120-CM2
52120-CM3 52120-7C3 52240-DM3
Para Asistencia Técnica llame al: 1-800-824-3005 (Sólo en EE.UU.) www.leviton.com
52277-0M3 52277-7M3 52277-CM3
52277-7C3 52347-0M3 52412-DS3
52480-DM3 57120-0M3 57120-CM3
57240-DM3 57277-0M3 57277-CM3
57346-0M3 57480-DM3 57600-DM3
Fig. 5Fig. 4 Fig. 6Fig. 1 Fig. 2 Fig. 3
PK-93212-10-02-0B© 2011 Leviton Mfg. Co., Inc.
Loading...