Page 1
Remote Control Panel
WEB VERSION
Installation &
Operation Guide
400CP
Page 2
Table of Contents
WEB VERSION
INTRODUCTION ................................................................................................................. 3
IMPORTANT......................................................................................................................... 3
WIRING................................................................................................................................. 3
PROGRAMMING.................................................................................................................. 5
OPERATION ....................................................................................................................... 12
Page 3
Introduction
WEB VERSION
The Leviton 400CP represents a key part of a state of the art, total lighting control system.
Combined with Leviton dimmers and optionally, a Leviton memory control console, a totally
integrated system is achieved.
The 400CP can automatically take control of up to 512 dimmer channels. Control is
automatically passed between400CP’s and the memory control console as desired.
The 400CP is exceptionally easy to operate and features 4zone control with programmable
fade times. Remote lockout capability is also included. Installation is a snap
with the simple 4 wire digital connection required.
Important
• Programming differs from other Luma-Net
• Luma-Net® control panels with software release 3.00 and higher are not directly compatible
and will not operate with older 400CP panels with software prior to release 3.00. Contact
dealer or factory for modifications if necessary.
• Leviton dimming systems used with these release 3.00 panels require the following
software releases:
2408CD, 2408CR, 2404CD release 2.30 and above.
DDS 8600/8800/9600/9800 release 1.30 and above. *
DDS 6000 release 1.30 and above. *
DDS 5300/5500/5600 release 1.30 and above. *
* Optional interface kit required for these units.
®
panels, please read instructions.
Wiring
WIRING
The 400CP will only operate with Leviton dimming and control systems explicitly designed for
interfacing with it. Communication between the 400CP and the dimming system is via a 4 wire
interface. Three wires carry the RS 422/485 bi-directional data. A fourth wire carries the DC
voltage necessary for powering the unit.
Wiring cable between the 400CP and the dimming system is class 2 and should be at least
22 AWG, 4 conductor shielded, twisted pairs (BELDEN 8302, 8723; 22 AWG).
The 400CP may be connected to the dimming system via parallel or daisy-chained wiring. Due
to power supply current demands, 400CP’s must be limited to 5 units per daisy chain run with
22 awg wire, or 10 units with 20 AWG wire.
The Luma-Net
from the panel to facilitate ease of wiring and testing. Connect the terminals marked remote+,
remote-, common, and +15 VDC to the same respective terminals on the dimming system and
other 400CPs. Use one twisted pair for remote+ and remote- and the other pair for common
and +15 VDC.
The wiring to the remote lockout switch, if used, can be simple 2 conductor 22 AWG. Connect
the wires from the switch to the lockout+ and lockout- terminals. Any panel or group of panels
may be locked-out remotely by interrupting the +15V supply to the panels. This should not
affect any other panels still powered, or affect lighting levels currently set.
IMPORTANT: Verify wiring is correct before powering system! Make sure nothing
conductive may touch pc board or components!
®
panels feature plug on wiring terminals. The terminals may be unplugged
Page 3
Page 4
MOUNTING
WEB VERSION
The 400CP will mount in any standard double-gang electrical box with the 4 screws provided. See
below paragraph on system turn-on before final mounting of panels.
SYSTEM TURN-ON
It is very important that the system operation be verified one panel at a time or else an improper
connection at one panel would cause the entire system to not operate properly and may be difficult
to diagnose.
After all terminal plugs have been wired and the dimmer system has been installed and tested,
the installer is ready to connect each panel to the system. Panels may be plugged-in while system
is live, but the installer must take care not to touch PC board or connections with fingers or metal
objects. On daisy-chain runs, the panels closest to the dimming system should be connected first.
400CP panels without dip switches must have their network ID programmed after the power
is connected. The panels that are provided with dipswitches should have the ID set before the
system is powered. It is recommended that the installer review the programming procedures
for network ID before proceding. A duplicate network ID number will cause the entire network to
malfunction.
Connect the first panel and immediately notice whether the POWER LED comes on, indicating
power to the panel. The BUSY LED should come on momentarily and then go out and stay out.
This indicates a successful reconfiguration of the network. If the BUSY LED flashes slowly, this
indicates a duplicate ID number or wiring problem. Program the ID number, if not already, and
observe the BUSY LED (Note - the busy LED also flashes quickly when the program jumper is
removed).
Now test the dimmer function by programming one scene or zone and operating the panel. If the
dimmer responds, then mount the panel and procede to the next panel in the system and follow
the same procedure.
LEDS
The PWR LED indicates the
presence of +15VDC to the
panel.
The BUSY LED indicates the
following:
Off Normal state when there is
no activity.
Short Blinks A message is
being sent on the network.
Steady on or Slow flashing
Network trying to reconfigure
(bad ID?)
While programming, the
following actions are normal.
Quickly flashing Programming
mode, no mode selected.
Off Programming mode, mode
selected.
LOCKOUT
Any 400CP may be disabled from operation with a remote key switch or other contact closure.
Several Luma-Net
as long as polarity is maintained.
Closing the contact will prevent connected panels from operating, regardless of button presses.
Luma-Net® panels may also be locked out by causing a switch to disconnect the +15V supply to
the panels.
®
panels of the same version may be connected to the same contacts in parallel
Page 4
Page 5
Programming
WEB VERSION
Several parameters must be programmed into the 400CP for it to operate properly:
Dimmer channel assignments for each scene.
Dimmer levels for each scene.
Fade time for each scene.
Master / Slave operation.
Network ID number (IMPORTANT).
Optionally, the unit may be ordered preprogrammed from the factory. Any field modifications
can be made if necessary.
Factory Default Setting:
The 400CP is programmed at the factory for zone 1-4 to be set for channel 1-4 respectively.
The fade rate ant other parameters are also set to factory defaults. This may be acceptable
for initial testing. If necessary to return the 400CP panel to it’s factory default settings (except
network ID), follow this procedure:
1. Remove program jumper block and disconnect plug-in terminal block.
2. Hold down all ZONE 1-4 LOWER buttons while connecting terminal block.
Full Memory Clear:
Normally, the 400CP will not require memory clearing. Once the memory is cleared, all
parameters, including fade rate, must be reprogrammed. Unless it is necessary to clear
memory to remove a large or unknown programming, skip these steps.
1. Remove program jumper block and disconnect terminal block.
2. Hold down all ZONE 1-4 RAISE buttons while connecting the terminal block.
Prepare the 400CP for reprogramming:
In order to program the 400CP, a jumper block must be removed from the program jumper
pins (See diagram). This will allow data to be stored in the eeprom memory. At this point the
BUSY LED will start flashing, indicating that you are in the program select mode.
IMPORTANT: After programming it is important to replace the programming jumper
block so memory will be protected.
Page 5
Page 6
Maximum number of dimmers.
WEB VERSION
This parameter must be set to reflect a number greater than or equal to the maximum number
of dimmer channels installed in the system. The factory default is 32 dimmer channels. If this
number is correct then this step may be ignored.
The maximum number of dimmers may be set as follows:
1. Make sure that the 400CP is in the program select mode as discussed.
2. Press the zone 1 increase button and the BUSY led will quit flashing.
3. Press button representing desired number of dimmers as shown in the diagram.
4. If more than 256 dimmers are required then press a second button so that the sum of the
values of the two buttons pressed will equal the desired number of dimmers.
5. The unit will exit this programming mode and the BUSY LED will start flashing again on
release of the second press, or after a few seconds if only one press was required.
DIMMER ASSIGNMENT MODE
LUMA-NET
SCENE 1 SCENE 2 SCENE 3 SCENE 4
DOWN UP ADD DELETE
PWR BUSY
404 CP
LUMA-NET
SCENE 1 SCENE 2 SCENE 3 SCENE 4
PWR BUSY
SCENE 5 SCENE 6 SCENE 7 SCENE 8
DOWN UP ADD DELETE
408 CP
Page 6
Page 7
Assigning dimmer channels to each scene.
WEB VERSION
Each of the zones of the 400CP must be programmed with the desired dimmer channel
assignments. Only the dimmer channels assigned will be affected by each zone’s increase
and decrease buttons. In order to easily identify dimmer channels while programming, the
system should have all installed lamps or loads operational. If this is not possible, the 400CP
to be programmed should be temporarily connected nearby to the dimmer units so that the
control LEDs of the dimmers may be observed to verify channel selection.
To program each zone:
1. Make sure that the 400CP is in the program select mode as discussed. The BUSY LED
should be flashing.
2. Press the zone 2 increase button to select "dimmer assignment mode" and the BUSY LED
will stop flashing.
3. Press INCREASE button representing desired zone to be programmed. At this point, all
currently assigned dimmers will come on. The current dimmer selector will be set to one.
4. Use the buttons marked as UP and DOWN in diagram to increment or decrement the
dimmer channel selector.
Tap the buttons the required number of times to reach the dimmer channel to be assigned.
5. Use the ADD and DELETE buttons to add or delete this dimmer from the zone. The lamps
connected to this dimmer channel will come on full when the ADD button is pressed.
Observe lamps or dimmer LEDs to verify correct channel has been selected.
6. A new zone can be programmed at any time by pressing the appropriate zone INCREASE
button. The dimmer selector number will always return to one when changing zones.
7. To exit this programming mode; press both the UP and DOWN buttons at the same time.
The BUSY LED will start flashing again when both buttons are then released.
DIMMER ASSIGNMENT MODE
LUMA-NET
INCREASE
ZONE 1 ZONE 2 ZONE 3 ZONE 4
PWR BUSY
400 CP
DOWN UP ADD DELETE
DECREASE
MEMORY LIGHTING CONTROLLER
Page 7
Page 8
Scene fade time programming.
WEB VERSION
Each zone may be programmed with an individual fade time. This is the time it will take the
dimmer channels assigned to go from full off to full on and visa versa. Fade time can vary from
0 to 13 seconds. A longer fade time will increase the accuracy when using the increase and
decrease buttons to set desired lighting levels. A fade time of 0 seconds will cause instant full
on or full off operation whenever the increase or decrease buttons are pressed. If the factory
default setting of 5 seconds is desired for each zone then this step may be ignored.
To program zone fade time:
1. Make sure that the 400CP is in the program select mode as discussed.
2. Press the zone 3 increase button to enter "fade time mode" and the BUSY LED will stop
flashing.
3. Select the desired zone by pressing the associated button as shown in the diagram.
4. Press button marked with desired fade time in seconds.
5. Unit will exit this programming mode after the release of the button and the BUSY LED will
start flashing again.
FADE TIME MODE
LUMA-NET
INCREASE
0 1 3 5
ZONE 1 ZONE 2 ZONE 3 ZONE 4
PWR BUSY
7 9 11 13
DECREASE
400 CP
MEMORY LIGHTING CONTROLLER
Page 8
Page 9
Master/Slave Mode
WEB VERSION
400CP panels may be slaved to one another. Several panels may act as slaves to a master
panel which contains the programming. The slaves will mimic the master LED’s and will
operate the scenes and fade times of the master. This is ideal for installations with several
panels in one room.
To make a panel into a master (factory default); set the Master\Slave ID to 0. To make a panel
into a slave; set the Master/Slave ID to the Network ID of the desired master to slave to.
To set Master/Slave ID number:
1. Make sure that the 400CP is in the program mode as discussed.
2. Press the zone 4 increase button and the BUSY LED will stop flashing
3. Look up the necessary sequence of 1’s and 0’ for the ID number on the chart at the end of
this section.
4. Using the two buttons indicated below, enter the eight number sequence of 1’s and 0’s.
5. The unit
NOTE : All other programming (except network ID) will have no effect if unit is made
into a slave. The master unit will contain the programming for all units slaved to it.
Slave units must still have a unique Network ID number (see following section).
MASTER / SLAVE MODE
ZONE 1 ZONE 2 ZONE 3 ZONE 4
PWR BUSY
0 1
LUMA-NET
INCREASE
DECREASE
400 CP
MEMORY LIGHTING CONTROLLER
Page 9
Page 10
Network ID number.
WEB VERSION
Since the Luma-Net® System is a digital network, all panels and devices attached
(except dimmers) must have a unique network ID number.
If two panels have the same network ID number, the entire network will stop
functioning.
Panels without a dipswitch must follow this procedure otherwise simply set the dipswitch as
per the chart on the following page.
To set Network ID number (units without dipswitch):
1. Make sure that the 400CP is in the program mode as discussed.
2. Press the zone 1,2,3,4 increase buttons at the same time and the BUSY LED will stop
flashing
3. Look up the necessary sequence of 1’s and 0’ for the ID number on the chart at the end of
this section.
4. Using the two buttons indicated below, enter the eight number sequence of 1’s and 0’s.
5. The unit will exit this program mode at the release of the eighth press, and the BUSY LED
will start flashing again.
NETWORK ID MODE
LUMA-NET
INCREASE
ZONE 1 ZONE 2 ZONE 3 ZONE 4
PWR BUSY
0 1
DECREASE
MEMORY LIGHTING CONTROLLER
400 CP
Page 10
Page 11
ID number codes / dipswitch settings
WEB VERSION
ID number 12345678 ID number 12345678 ID number 12345678
0 00000000 1 10000000 2 01000000
3 11000000 4 00100000 5 10100000
6 01100000 7 11100000 8 00010000
9 10010000 10 01010000 11 11010000
12 00110000 13 10110000 14 01110000
15 11110000 16 00001000 17 10001000
18 01001000 19 11001000 20 00101000
21 10101000 22 01101000 23 11101000
24 00011000 25 10011000 26 01011000
27 11011000 28 00111000 29 10111000
30 01111000 31 11111000 32 00000100
33 10000100 34 01000100 35 11000100
36 00100100 37 10100100 38 01100100
39 11100100 40 00010100 41 10010100
42 01010100 43 11010100 44 00110100
45 10110100 46 01110100 47 11110100
48 00001100 49 10001100 50 01001100
51 11001100 52 00101100 53 10101100
54 01101100 55 11101100 56 00011100
57 10011100 58 01011100 59 11011100
60 00111100 61 10111100 62 01111100
63 11111100 64 00000010 65 10000010
66 01000010 67 11000010 68 00100010
69 10100010 70 01100010 71 11100010
72 00010010 73 10010010 74 01010010
75 11010010 76 00110010 77 10110010
78 01110010 79 11110010 80 00001010
81 10001010 82 01001010 83 11001010
84 00101010 85 10101010 86 01101010
87 11101010 88 00011010 89 10011010
90 01011010 91 11011010 92 00111010
93 10111010 94 01111010 95 11111010
96 00000110 97 10000110 98 01000110
99 11000110 100 00100110 101 10100110
102 01100110 103 11100110 104 00010110
105 10010110 106 01010110 107 11010110
108 00110110 109 10110110 110 01110110
111 11110110 112 00001110 113 10001110
114 01001110 115 11001110 116 00101110
117 10101110 118 01101110 119 11101110
120 00011110 121 10011110 122 01011110
123 11011110 124 00111110 125 10111110
126 01111110 127 11111110
For channels 129 - 256 Set dipswitch 1-7 as above and set dipswitch #8 on.
Page 11
Page 12
Operation
WEB VERSION
To raise lighting levels:
Press and hold the increase button of the zone desired. The 400cp will then take control
of all dimmer channels assigned to the selected zone and increase lighting levels at the
programmed fade rate. Release button when correct lighting levels are attained.
To lower lighting levels:
Press and hold the decrease button of the zone desired. The 400cp will then take control
of all dimmer channels assigned to the selected zone and decrease lighting levels at the
programmed fade rate. Release button when correct lighting levels are attained.
To restore control from a console:
Simply perform a change in the channel level from the console. The lighting channel will then
fade back to the new console level at the same fade rate as last commanded by the 400CP for
that channel. Once the console level matches or is moved past the lighting level, full console
control will be resumed for that channel.
REAR VIEW OF 400CP
TERMINATION
JUMPER
PROGRAM
LO+
LO+VDC
COM
REMREM+
TERMINAL
BLOCK
UNIT WITH DIP SWITCH
FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton Manufacturing of Canada Ltd
to the attention of the Quality Assurance Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone at 1 800
405-5320.
LIMITED 2 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is
free of defects in materials and workmanship under normal and proper use for two years from the purchase date. Leviton’s only obligation is to
correct such defects by repair or replacement, at its option. For details visit www.leviton.com or call 1-800-824-3005. This warranty excludes
and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or
in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or
not in accordance with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and fitness
for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including
merchantability and fitness for a particular purpose, is limited to two years. Leviton is not liable for incidental, indirect, special, or consequential
damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this
warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
JUMPER
ID NUMBER
DIP-SWITCH
LO+
LO+VDC
COM
REMREM+
TERMINAL
BLOCK
UNIT WITHOUT DIP SWITCH
PROGRAM
JUMPER
For Technical Assistance Call: 1-800-824-3005 (U.S.A. Only) www.leviton.com
Page 12
DI-000-N0400-00F© 2016 Leviton Mfg. Co., Inc.
Loading...