Page 1
Floor Boxes - Double-Gang
WEB VERSION
Cat. No. 35249
Rated: 15A - 125V
Cat. No. 35349
Rated: 20A - 125V
Installation Instructions
WARNINGS AND CAUTIONS
!
PK-A3125-10-00-0B
Floor Boxes with 2 Duplex Receptacles
(Cat. Nos. 35249-TFx, 35349-TFx)
Screw Cap
(Brass or Nickel Plate)
Rubber O-Ring
(pre-assembled on screw caps)
Floor Boxes with 1 Duplex Receptacle and 1 Duplex QuickPort® Insert
(Cat. Nos. 35249-TLx, 35349-TLx)
Screw Cap
(Brass or Nickel Plate)
WARNING
Failure to use a divider in a floor
box with high voltage and low
Rubber O-Ring
(pre-assembled on screw caps)
voltage wiring can cause fire, shock
or death. Ensure divider is in place
before installation.
WARNING: TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT
BREAKER OR FUSE AND TEST THAT THE POWER IS OFF BEFORE WIRING!
WARNING: TO AVOID FIRE, SHOCK OR DEATH: USE A DIVIDER IN A FLOOR BOX
WITH HIGH VOLTAGE AND LOW VOLTAGE WIRING AND ENSURE DIVIDER IS IN
PLACE BEFORE INSTALLATION.
• To be installed and/or used in accordance with appropriate electrical codes and
regulations.
• If you are unsure about any part of these instructions, contact an electrician.
• Use this device with copper or copper clad wire only.
• Electrical box is not suitable for masonry applications.
• Suitable for wood finished floors, tile, vinyl and industrial carpet 3/8" (1.0 cm)
thickness only. Clean floor surfaces before mounting. Use all purpose sealing
compound (not provided) as shown.
• Use only electrical mounting box provided.
NEMA
Configurations
15A - 125V
G
W
Cat. No. 35249
20A - 125V
G
W
Cat. No. 35349
Bare Floor Installation Carpet Installation
(4) Screw #6-32
(Brass or Nickel Plate)
(4) O-Seal Washer
Brass Plate
or Nickel Plate
Gasket
(2) Shell
(molded plastic)
(4) Screw #6-32
(Brass or Nickel Plate)
(4) O-Seal Washer
Brass Plate
or Nickel Plate
Gasket
(2) Shell
(molded plastic)
Mounting
Duplex
QuickPort
®
Insert
Screw
Line
Voltage
Installation
Divider
Low
Voltage
Installation
NOTE
Insert QuickPort® snap-in modules
as shown: "UP" on connector must
face "UP" on duplex QuickPort
®
insert.
The duplex receptacles included in this assembly are covered by U.S. Patent Nos.
7,355,117; 7,820,909; 7,868,719; 8,242,362 and corresponding foreign patents.
LIMITED 10 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that
this product at the time of its sale by Leviton is free of defects in materials and workmanship under
normal and proper use for ten years from the purchase date. Leviton’s only obligation is to correct
such defects by repair or replacement, at its option. For details visit www.leviton.com or call
1-800-824-3005. This warranty excludes and there is disclaimed liability for labor for removal
of this product or reinstallation. This warranty is void if this product is installed improperly
or in an improper environment, overloaded, misused, opened, abused, or altered in any
manner, or is not used under normal operating conditions or not in accordance with any
labels or instructions. There are no other or implied warranties of any kind, including
merchantability and fitness for a particular purpose, but if any implied warranty is
required by the applicable jurisdiction, the duration of any such implied warranty, including
merchantability and fitness for a particular purpose, is limited to ten years. Leviton is not
liable for incidental, indirect, special, or consequential damages, including without
limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay
or failure to perform this warranty obligation. The remedies provided herein are the
exclusive remedies under this warranty, whether based on contract, tort or otherwise.
For Technical Assistance Call: 1-800-824-3005 (U.S.A Only) www.leviton.com
FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should contact Leviton
in writing at Leviton Manufacturing of Canada Ltd to the attention of the Quality Assurance
Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone
at 1 800 405-5320.
© 2016 Leviton Mfg. Co., Inc.
Mounting
Screw
(2) Duplex
Receptacle
(Cat. No. 35349-TF
depicted)
(4) #6 x 1"
Screw
(2) Mounting
Bracket
(4) Phillips Pan
Head Screw
Duplex
Receptacle
Mounting
Screw
(Cat. No. 35349-TL
depicted)
Duplex
QuickPort
®
Insert
(4) #6 x 1"
Screw
(2) Mounting
Bracket
(4) Phillips Pan
Head Screw
Divider
NOTE: For low voltage installations, follow the instructions that
come with your Leviton QuickPort
®
modules (sold separately).
QuickPort
snap-in
module
®
Page 2
STEP 1
WEB VERSION
IMPORTANT NOTE: Oval adjustment hole on bracket MUST be mounted to floor box.
Remove desired knockouts in floor box before mounting.
ADJUST AND TIGHTEN MOUNTING BRACKETS T
O FLOOR BOX
NOTE: Ensure mounting brackets on the floor box are fully in the "DOWN" position.
Securely torque mounting bracket screws 12-14 in-lbs prior to floor installation.
STEP 3
A) Mount box.
* Use sealing
compound
under brackets
MOUNT FLOOR BOX, RECEPT
C) Place plastic shells
over devices.
ACLE AND SHELL
B) Pull conductors. Wire and mount
receptacles.
STEP 5
MOUNT COVER PLATE
NOTE: Torque mounting plate screws to 9 in-lb.
NOTE: Use screw cap when not in use. O-rings are pre-assembled to screw caps.
Apply an all purpose silicone lubricant to O-ring before assembly. Torque
screw cap to 20 in-lb.
BARE FLOOR CARPET
NOTE:
when mounted properly. Follow steps for correct installation.
STEP 2
BARE FLOOR CARPET
A) Place floor cut out template on floor in
B) Cut mounting area for floor box.
The floor box will be recessed (below floor surface),
CUT CARPET (if applicable), and FLOOR
desired location and trace.
A) Cut a 4" x 4-17/32" hole in carpet in desired
location.
CAUTION:
recommended dimensions. A larger opening
may compromise the integrity of the seal.
B) Place floor cut out
Do not cut carpet opening larger than
4"
template (centered)
and trace.
17
32
4- "
Neutral
(White)
Grounding
Screw
(Green)
Hot (Black)
Cat. No. 35349-TF
depicted
STEP 4
BARE FLOOR CARPET
• Apply sealing compound
• Add O-seal washers to cover plate screws
• Place gasket
Sealing compound Sealing compound
SEAL DEVICE ACCORDING TO APPLICATION
• Apply sealing compound (2 places)
• Add O-seal washers to cover plate screws
Note: Gasket is not required for carpet
installations.
4-3/16"
Carefully cut template along dotted line
2-13/16"
Floor Cut Out
Template
R 1/4" Typ
"61/5-3
NOTE: Remove debris and clean
floor surfaces before mounting.
C) Cut mounting
area for floor
box.
O-seal
washer
Gasket Carpet
O-seal
washer
Sealing
compound
2-3/16"
4-5/32"
PK-A3125-10-00-0B
Loading...