Page 1
PK-93600-10-00-0E
Floor Box Assembly
Cat. No. 5249
Rated: 15A - 125V
Cat. No. 5349
Rated: 20A - 125V
Cat. No. 25249
Rated: 15A - 125V
Cat. No. 25349
Rated: 20A - 125V
Installation Instructions
WARNING: TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT
BREAKER OR FUSE AND TEST THAT THE POWER IS OFF BEFORE WIRING!
WARNING: To be installed and/or used in accordance with appropriate electrical codes
and regulations.
WARNING: If you are unsure about any part of these instructions, contact an electrician.
CAUTION: Use this device with copper or copper clad wire only.
CAUTION: Electrical box is not suitable for masonry applications.
CAUTION: Suitable for wood finished floors and industrial carpet 3/8" (1.0 cm)
thickness only. Clean floor surfaces before mounting. Use all purpose sealing compound
(not provided) as shown.
CAUTION: Use only electrical mounting box provided.
!
WARNINGS AND CAUTIONS
SINGLE RECEPTACLE CONTENTS (Cat. Nos. 5249/5349) DUPLEX RECEPTACLE CONTENTS (Cat. Nos. 25249/25349)
15A - 125V
G
W
Cat. No. 5249
G
W
Cat. No. 5349
20A - 125V
NEMA
Configuration
s
(4) #6 x 1" Screw
Box (UL Listed
)
Single Receptacle
Shell (Molded Plastic)
Gasket
Brass Plate
(2) O-Seal Washer
(2) Screw #6-32 (Brass)
O-Ring (Rubber)
Screw Cap (Brass)
(2) Mounting
Bracket
(4) Phil-Pan
Head Screw
Bare Floor Carpet
15A - 125V
G
W
Cat. No. 25249
G
W
Cat. No. 25349
20A - 125V
NEMA
Configurations
(2) Screw Cup
(Brass or Nickel Plate)
(2) O-Ring (Rubber)
(2) Screw #6-32
(Brass or Nickel Plate)
(2) O-Seal Washer
Brass Plate
or Nickel Plate
Gasket
Shell
(Molded Plastic)
Duplex Receptacle
(2) Brass
Terminal Screws
(4) #6 x 1" Screw
(2) Mounting
Bracket
(4) Phil-Pan
Head
Screw
Silver
Terminal
Screws
(not shown)
Green
Ground
Screw
Box (UL Listed
)
Bare Floor Carpet
For Technical Assistance Call:
1-800-824-3005 (U.S.A Only)
www.leviton.com
FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should contact Leviton
in writing at Leviton Manufacturing of Canada Ltd to the attention of the Quality Assurance
Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone
at 1 800 405-5320.
LIMITED 10 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that
this product at the time of its sale by Leviton is free of defects in materials and workmanship under
normal and proper use for ten years from the purchase date. Leviton’s only obligation is to correct
such defects by repair or replacement, at its option. For details visit www.leviton.com or call
1-800-824-3005. This warranty excludes and there is disclaimed liability for labor for removal
of this product or reinstallation. This warranty is void if this product is installed improperly
or in an improper environment, overloaded, misused, opened, abused, or altered in any
manner, or is not used under normal operating conditions or not in accordance with any
labels or instructions. There are no other or implied warranties of any kind, including
merchantability and fitness for a particular purpose, but if any implied warranty is
required by the applicable jurisdiction, the duration of any such implied warranty, including
merchantability and fitness for a particular purpose, is limited to ten years. Leviton is not
liable for incidental, indirect, special, or consequential damages, including without
limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay
or failure to perform this warranty obligation. The remedies provided herein are the
exclusive remedies under this warranty, whether based on contract, tort or otherwise.
© 2017 Leviton Mfg. Co., Inc.
These products are covered by U.S. Patents Nos. 7,355,117*; 7,820,909*; 7,868,719†; 8,242,362* and corresponding foreign patents
(*Applies only to 5249-TFB, 5349-TFB, 25249-TFB, 25249-TFN, 25349-TFB, 25349-TFN; †Applies only to 25249-TFB,
25249-TFN, 25349-TFB, 25349-TFN).
Page 2
4"
2-¾"
Neutral (White)
Hot (Black)
Grounding Screw
(Green)
STEP 1
STEP 5
ASSEMBLE MOUNTING BRACKETS TO FLOOR BOX
MOUNT COVER PLATE
NOTE: Use screw cap when not in use.
IMPORTANT NOTE: Oval adjustment hole on bracket MUST be mounted to floor box.
Remove desired knockouts in floor box before mounting.
SINGLE RECEPTACLE - Mount brackets on ENDS of floor box in the "UP" position.
BARE FLOOR CARPET
DUPLEX RECEPTACLE - Mount brackets on SIDES of floor box in the "DOWN" position.
STEP 2
CUT CARPET (if applicable), and FLOOR
A) Cut a 4" x 2-¾" hole in carpet in desired
location.
CAUTION:
Do not cut carpet opening larger than
recommended dimensions. A larger opening
may compromise the integrity of the seal.
A) Place floor cut out template on floor in
desired location and trace.
B) Cut mounting area for floor box.
NOTE: Remove debris and clean
floor surfaces before mounting.
B) Place floor cut out
template (centered)
and trace.
C) Cut mounting
area for floor
box.
STEP 3
MOUNT FLOOR BOX, RECEPTACLE AND SHELL
Carefully cut template along dotted line
B) Pull conductors. Wire and mount
receptacle.
C) Place plastic shell
over receptacle.
A) Mount box.
* Use sealing
compound
under brackets
STEP 4
SEAL DEVICE ACCORDING TO APPLICATION
BARE FLOORBARE FLOOR CARPETCARPET
Sealing compound
• Apply sealing compound
• Add O-seal washers to cover plate screws
• Place gasket
• Apply sealing compound (2 places)
• Add O-seal washers to cover plate screws
Note: Gasket is not required for carpet
installations.
Sealing compound
O-seal
washer
O-seal
washer
Gasket Carpet
• Apply an all purpose silicone lubricant to O-ring before assembly
PK-93600-10-00-0E
Floor Cut Out
Template
1"
R 1/4" Ty
p
2-9/32"
"61/5-3
3/8"
4-3/16"
Page 3
ARTWORK PRINT SPECIFICATIONS
DIMENSIONS / FOLD SCHEME / BINDERY DIAGRAM
PART NUMBER REV DESCRIPTION
Line Screen:
Angle:
Resolution:
Offset Flexo
Other
Body Material:
Bindery
Thickness:
Trim
Perfect Bind
Die cut
Saddle Stitch
Drill
Fold
The information in this document is the exclusive PROPRIETARY property of LEVITON MANUFACTURING COMPANY, INC. It is disclosed
with the understanding that acceptance or review by the recipient constitues an undertaking by the recipient. (1) to hold this information in strict
confidence, and (2) not to disclose, duplicate, copy, modify or use the information for any purpose other than that for which disclosed.
PlantApprovals:
PN-ARN: Pilot Rev:ECR Number:
Released Artwork Format:
Production PDF
Artwork Release Date:
Artwork Print Specification Sheet Rev A11.eps
PMCQA
Artist:
Notes:
Other
Cust Other
S & A
Mktg Eng
FOR LEVITON USE ONLY
SPECIFICATIONS :
PROCESS :
MANUAL INTERIORS / BINDERY / FOLD SCHEME :
COMMENTS :
For manuals - designates cover specifications
Material:
Thickness:
Finish:
:
Spot
CMYK
1:
4:
3:
2:
Colors: over
1:
4:
3:
2:
Fonts:
Spot
CMYK
1:
4:
3:
2:
Colors: over
1:
4:
3:
2:
Fonts:
Fold Line
Die Cut Punch/Drill Hole
Glue
Kiss Cut
Cellophane
Fold Line
Perforate
Die Cut
Die Line Key:
PK-93600-10-00-0E Instruction Sheet
40 lb.
Black Helvetica
X
1 1
X
X
81 I. Fierro
c.buttitta
EC11803-C002693 ECR11803
k.markell
x x
xx
x
T. Pulsonetti
M. Laurent
11"
17"
Part No.
FINAL
5.5"
2.83"
Part No.
* NOTE: Ensure instruction sheet is printed
at 100% (1:1 scale).
2/16/17
Loading...