Levelpro TKS-25-PF, TKP-80-PP, TKP-15-P, TKM-20-PF, TKP-25-PF User manual

TKS | TKP | TKM ROTATOR SERIES MANUAL

Multi-Function Paddle Wheel Flow Meter

TK SERIES MANUAL

Flow Rate & Totalizer

Password Security Protected
Zirconium Ceramic | Rotor | Bearings

Display Rotates 360 Degrees

right LED Display

B

Programming

Read carefully the instructions published in this manual before the first use of the sensor. Keep the manual

at a safe place. The manufacturer reserves the right to implement changes without prior notice

© Icon Process Controls Ltd. All Rights Reserved

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

TKS| TKP | TKM ROTATOR SERIES MANUAL

Multi-Function Paddle Wheel Flow Meter

TABLE OF CONTENTS

1. Product Description

2. Parts TK Series

3. Product Selection

4. Specifications

5. Procedure to Rotate Display

6. Programming Models TKP | TKM

6.1 Programming NPN Pulse Output Models TKP | TKM Only

6.2 Programming NPN Pulse Control Function Models TKP | TKM Only

6.3 Mode of NPN Pulse Output TKP | TKM Models

6.4 K-Factors for TK

6.5 Programming TKS Model Only

6.6 Programming TKS Model Only Program Relay Set Point and Relay Delay (Prevents Relay Chatter)

6.7 Relay ON - OFF Options For TKS Series Only

6.8 General Terms

7. Standard Pipe Size

8. Pressure vs. Temperature (psi, water, non-shock)

9. Wiring Diagram

9.1 TKP - Flow Rate + Flow Totalizer + NPN Pulse Diagram

9.2 TKM - (4-20mA or 0-5V DC + NPN Pulse) Flow Rate + Flow Totalizer + Pulse Diagram

9.3 TKS NPN (Flow Rate + Relay + Pulse) Diagram

10. Installation Positions

Installation Positions 10

11. Warranty, Returns and Limitations

02

03

03

03

04

04

05

05

06

06

06

07

07

07

08

08

08

08

08

09

09

11

© Icon Process Controls Ltd. All Rights Reserved

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

02

TKS| TKP | TKM ROTATOR SERIES MANUAL

Multi-Function Paddle Wheel Flow Meter

2. Parts TK Series

1. Flow Controller

2. Power Supply

3. Hall Sensor

4. Paddle Wheel

6

7

8

1

2

3

4

5

5. Body (PVC, PP,

PVDF)

6. Tefzel Paddle

7. Rotor Pin

8. Bearing

3. Product Selection

EXAMPLE

TKP ---- 25 ---- P ---- E ---- T ---- RS ---- M

(1) (2) (3) (4) (5) (6) (7)

1. SERIES

a) TKS = Paddle Wheel Flow Meter with Relay + Pulse
b) TKP = Paddle Wheel Flow Meter - (Flow Rate +

c) TKM = Paddle Wheel Flow Meter - 4-20mA + (Flow Rate

2. PIPE SIZE

15 | (½") | 20 | (¾")
25 | (1") | 40 | (1 ½")
50 | (2") | 80 | (3") | 100 / (4")

3. BODY MATERIAL

P = PVC
PP = Polypropylene
PF = PVDF

4. SEALS*

E = EPDM (Optional)
F = FFKM (Optional)

Flow Total) Pulse Output

+

Flow Total) Pulse Output

* CPVC Socket Unions Available

* FPM is Standard

4. Specifications

Fluid

Accuracy

Max Flow Velocity

Min Flow

Operating Press

Turndown

Response Time

Material of
Construction

Operating
Temperature

Liquid - Viscosity
Range <.5-20 centistokes

> .5% of F.S. @ 68°F | 20°C |
Repeatability 0.5 of Full Scale

32.8 ft/s max | 10 m/s max

0.8 ft/s min | 0.3 m/s min

150 psi

33:1

Real Time

Paddle : Tefzel | Zirconium Ceramic
Body : PVC | PP | PVDF
Shaft : Zirconium Ceramic
Seals : FPM* | EPDM

PVC < 140°F | 60°C
PP < 176°F | 80°C
PVDF < 240°F | 115°C
316 SST< 248°F | 120°C

5. END CONNECTIONS

S - Sch 80 Soc
T - NPT
B - SDR11
D - DIN
F - A

Butt

NSI 150 lb

6. RS = TKP Series (Only) with RS-485 MODBUS

7. M = M12 - 2 Meters - Quick Disconnect (Option)

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Electronics

Protection Class

Approval

Current Draw

Battery

122°F °C

NEMA 4X | IP66

CE | Rohs

60mA Max

10-30VDC

© Icon Process Controls Ltd. All Rights Reserved

03

TKS| TKP | TKM ROTATOR SERIES MANUAL

Multi-Function Paddle Wheel Flow Meter

5. Procedure to Rotate Display

1 2 3

Flow Meter & Transmitter

OP2

FTM

OP1 GPM

Flow Meter & Transmitter

OP2

FTM

OP1 GPM

Using an allen key loosen the 2 screws

located on either side of the display Pull the screws | Do Not Remove

4 5 6

F

Flow Meter & Transmitter

O
P2

M T F

OP1

GPM

Flow
M
et
er & Transm

OP

F

2

F

itter

T
M

O
P1

GP
M

Rotate Display - 90 Degrees Lower Display

OP2

OP1 GPM

FTM

Lift the Display

F

Transmitter

P
2

FTM

OP
1

G
PM

Flow Meter &

O

Tighten the Allen screws | Snug Tight
Do Not Over-Tighten

6. Programming Models TKP | TKM

STEPS

Step-1

Home Screen

Press +

SET

F

(Together)

Step-2

Programming of Lock

Out Feature

Press

Step-3

Programming
Units of Flow

Press

No Programming

Step-4

Coefficient of

Flow Volume

Press

(HOLD)

3

Required

Flow Meter & Transmitter

OP2

TKP

SET

F

Flow Meter & Transmitter

OP2

TKP

SET

F

Flow Meter & Transmitter

OP2

TKP

SET

F

Flow Meter & Transmitter

OP2

TKP

SET

F

CV

SV

OP1 GPMFTM

LPM

FTM

CV

SV

OP1 GPMFTM

LPM

FTM

CV

SV

OP1 GPMFTM

LPM

FTM

CV

SV

OP1 GPMFTM

LPM

FTM

TKP | TKM Series Only
Power On Flow Meter with DC Power

Display will Show

0 Totalizer (Top RED)
0 Flow Rate (Bottom GREEN)

Programming Lock Out Feature TKP | TKM Series

Lck = 10 (Unlocked) : Factory Default, IF Lck is Changed from the # 10 the Flow Meter
will be in Lockout Mode.

LCK 10 (Default) To Unlock ensure Lck # is set to 10.

Programming Units of Flow TKP | TKM Series Only

Program Flow Units 0 | 1 | 2

Ut = 0 : (LPM) Ut = 1 : (GPM) (Default) Ut = 2 : {Kiloliter (KL)}

TKP | TKM Series Only

K-Factor : 0.1 - 999.9 (K-Factor is Factory Preset)

K-Factor Preset (Do Not Change

*Divide K Factor BY 3.8 TO CHANGE FROM GPM TO LPM

Step-5 For Programming 4-20mA Analog Output

TKM (4-20mA) and TKP with (RS 485 Option) Only

Step-5

Program Range of Transmitter

TKM Model Only

Press

Find Quality Products Online at: [e-mail]

Flow Meter & Transmitter

TKP

OP2

SET

F

CV

SV

OP1 GPMFTM

LPM

FTM

TKM (4-20mA) and TKP with (RS 485 Option) Only

Programming Analog Transmitter Range Output 4-20mA
Range : 0.1 - 999.9 4 mA = 0 20 mA = Entered Number.
TR 100 (Default) 4 mA = 0 GPM 20mA =100 GPM
This can be Change to Conform to Customers Application (Ex. Number Changed to 150)

www.GlobalTestSupply.com

OPERATIONDISPLAY

24V DC POWER ONLY

© Icon Process Controls Ltd. All Rights Reserved

04

TKS| TKP | TKM ROTATOR SERIES MANUAL

Multi-Function Paddle Wheel Flow Meter

6.1 Programming NPN Pulse Output
Models TKP | TKM Only

Steps Only Necessary If NPN Pulse Output is Required

STEPS

Step-1

Home Screen

Press

Step-2

Programming Flow Rate

Pulse Output

Press

To
Change
Value

Flow Meter & Transmitter

OP2 OP1

TKP

SET

F

Flow Meter & Transmitter

OP2 OP1

TKP

SET

F

CV

SV

LPM

FTM

CV

SV

LPM

FTM

TKP | TKM Series
Only

1000 Default
One Pulse Per Gallon
Default
(Flow Rate) Pulse

Press SET to Save and Proceed to the Next Screen

Step-3

Programming Flow T otal

Pulse Output

Press

Flow Meter & Transmitter

OP2 OP1

TKP

SET

F

CV

SV

LPM

FTM

2000 Factory Default
One Pulse Per Gallon
Default

2000 Default this can be Changed to Desired Value Refer to Next Page Programming OP2 Output for Options for Totalizer
Flow Totalizer Pulse (Step #2-Next)

Press SET Button to Save and Proceed to Next Screen

Step-4

Return to Home Screen

Press

Flow Meter & Transmitter

OP2 OP1

TKP

SET

F

CV

SV

LPM

FTM

Return to Home Screen

0 To

talizer Default

0.0 Flow Rate Default

OPERATIONDISPLAY

CV Display Reads 0
SV Display Reads 0
0 Totalizer Default

0.0 Flow Rate Default

Program Value of (Flow Rate) Pulse (NPN) Output

CV

Preset Value of Flow Rate

CV = Current Value
SV = Programmed Value

Change to a Value that meets your Flow Rate Pulse Output

CV > SV Flow Rate Pulse Output ON

SV

CV < SV Flow Rate Pulse Output OFF

Program Value of Flow Totalizer Pulse (NPN) Output

CV

SV : Preset value of Flow Total

SV

CV > SV Flow Rate output ON

Op1 & Op2 = 150mA Max Switching Currency

Current + Consumption is 60mA Max.
CV = Current Value = Current Flow Rate on Display
SV = Selected Value (Programmed Value Customer Entered)
NPN Pulse is a Transistor

6.2 Programming NPN Pulse Control Function
Models TKP | TKM Only

STEPS

Step-1

Home Screen

Press

Step-2

Programming OP2 Output

Pulse Control (Totalizer)

Press

Step-3

Programming OP1 Output
Pulse Option (Flow Rate)

Press

Step-4

Programming Hysteresis

of Output Flow Rate Pulse

Press

Step-5

Programming OP1 Power On Delay

Time For Initial Start UP (Sec)

Press

(HOLD)

3

(HOLD)

3

(HOLD)

3

(HOLD)

3

Flow Meter & Transmitter

OP2 OP1

TKP

SET

F

Flow Meter & Transmitter

OP2 OP1

TKP

SET

F

Flow Meter & Transmitter

OP2 OP1

TKP

SET

F

Flow Meter & Transmitter

OP2 OP1

TKP

SET

F

Flow Meter & Transmitter

OP2 OP1

TKP

SET

F

CV

SV

LPM

FTM

Power On Flow Meter With 10-30 V DC
0 Flow Totalizer

0.0 Flow Rate

Program (NPN) Pulse

CV

SV

LPM

FTM

CV

SV

LPM

FTM

CV

SV

LPM

FTM

CV

SV

LPM

FTM

Output (OP2) Totalizer

ange E.n.r.c.

R

Program Flow Rate
Pulse (NPN) Output (OP1)
Range: 0 - 3

Program Hysteresis of NPN Output Pulse
Range 0.1-999.99 (GAL) Hysteresis

HYS ± 1.0 GPM (Default)

Hys - Hysteresis is a buff

er around the Programmed Set Point Example

(Example) Liquid Caused by Pump Stopping or Va

Flow Rate

Program Time Delay for NPN Pulse (OP1) on Initial Start Up
Range : 0-9999 (Secs)
Ti

me Delay of Pulse Output (Flow Rate)

T2 = 20 (Secs) (Default) Flow Rate

OPERATIONDISPLAY

Con = n : Manual Reset;
Con = c : time (1=10 Secs) A

uto Reset Using Timer
Con = c : time (secs) Auto Reset Using Timer i.e 5 =Pulse On (5 secs)
Con = r : Auto Reset when Total Volume Value = Selct Value (SV)
Con = E : Pulse Output of Unit volume (Default) = One Gal/Pulse
Con = F Paddle Pulse Frequency Max 5 KHZ

Con = E (Default)

CV > SV Pulse (NPN) ON
CV < SV - HYS Pulse (NPN) OFF
CV > SV Pulse (NPN) ON
CV > SV + HYS Pulse (NPN) OFF

ALT

0 (Default) Most Common

CV = C urrent Value
SV = P rogrammed Value
Hys = See below

lve Closing i.e.-sloshing

© Icon Process Controls Ltd. All Rights Reserved

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

05

TKS| TKP | TKM ROTATOR SERIES MANUAL

Multi-Function Paddle Wheel Flow Meter

6.3 Mode of NPN Pulse Output TKP | TKM Models

DESCRIPTIONALT NO.

ALt = 0

ALt = 1

ALt = 2

ALt = 3

Current Value = Flow Rate

CV > SV ON: CV < SV - HyS OFF

CV < SV ON: CV > SV + HyS OFF

SV + HyS > CV > SV - HyS ON: CV > SV + HyS or CV < SV - HyS OFF

SV + HyS > CV > SV - HyS OFF: CV > SV + HyS or CV < SV - HyS ON

SV = Selected Value = Programmed Value (Customer)

Hys = Hysteresis ACTS Lika Buffer ± Around Pulse Output (Measured in GPM)

6.5 Programming TKS Model Only

STEPS

Step-1

+RPH6FUHHQ

Press

Step-2

Press

+

SET

F

(Together)

Programming Lock

Output

(HOLD)

3

TKS

TKS

Flow Meter

SET

Flow Meter

SET

GPM

Alarm

F

GPM

TKS Series Only

Power Up Flow Meter with DC Power

000.0

Programming Lock - Out Secure Feature
Lk = 10 (Unlocked Status) - (Default)
Changing Number will Lock Flow Meter

Alarm

F

LK.10 (Default)
1

0 = Unlocked

If any other Number is entered the Programming will be restricted

6.4 K-Factors for TK

Size

½"

¾"

1"

1 ½"

2"

3"

4"

Required when Programming Remote
Display or Controller.

K-Factor Pre Programmed by Factory - No Flow Meter
Programming of a K-Factor is required.

OPERATIONDISPLAY

LPM

124

72

54

19

10.3

4.7

2.1

GPM

471

274

171

72

39

18

8

24V DC POWER ONLY

Step-3

No Programming
Required K Value

Press

Step-4

Programming

Units of Flow

Press

Step-5

Programming Communication

Output Type

Press

Step-6

Programming

of Relay Set Point

Press

Step-7

Programming Relay

Time Delay

Press

TKS

TKS

TKS

TKS

TKS

Flow Meter

SET

Flow Meter

SET

Flow Meter

SET

Flow Meter

SET

Flow Meter

SET

GPM

K-Factor Range : 0.1-999.9 (Depends on Meter Size - Factory Pre- Programmed)

Alarm

F

GPM

K Value Preset (Do Not Change)

Program Flow Units 0,1,2
Ut = 0 : (LPM)

Alarm

F

GPM

Ut = 1 : (GPM) (Default)
Ut = 2 : {Kiloliter (KL)}

Programming NPN Pulse Output
con.E - Output = 1 Pulse / Gal

Alarm

F

GPM

con.F - Paddle Pulse Output 5KHZ MAX-Remote Display

con.E (Default)

Programming Relay Setpoint ON - OFF Options
Select - ALt.0, ALt.1, ALt.2, ALt.3,

Alarm

F

GPM

Alarm

F

ALt.0 (Default)

See Next Page for Relay A

larm Options-

Programming Initial Start-Up Relay Time Delay
Range : 0-99 sec Delay Time to Power on Alarm Output Relay
t.20 (Default) (20 Seconds)
Initial Start up of Flow Meter or Process (Allows for System
Steady State before Relay Switch becomes A

ctive).

© Icon Process Controls Ltd. All Rights Reserved

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

06

TKS| TKP | TKM ROTATOR SERIES MANUAL

Multi-Function Paddle Wheel Flow Meter

6.6 Programming TKS Model Only
Program Relay Set Point and Relay Delay (Prevents Relay Chatter)

STEPS

Step-1

Home Screen

Press

Step-2

Programming Relay

Set Point

Press

Step-3

Programming Relay

Hysteresis

Press

(HOLD)

3

TKS

TKS

TKS

Flow Meter

SET

Flow Meter

SET

Flow Meter

SET

GPM

Power On Flow Meter - 24VDC

Alarm

F

GPM

Home Screen 000.0 (Defaut)

Programming Relay Set Point. (When Relay Switches)
Range : 0.1 - 999.9 GPM

Alarm

F

GPM

100.0 GPM (Defaut)
Relay will Activate when this Set Point or (Flow Rate) is Reached

Program Relay Hysteresis - Prevents Relay Chatter - Due to Constant Flow Rate Change
around Setpoint in Dynamic Flow Process (Cushion ±) Prevents Relay

Alarm

F

d = Delay 0.10 GPM
d.0.10 (Defaut)

6.7 Relay ON - OFF Options For TKS Series Only

DESCRIPTIONALT NO.

ALt = 0

ALt = 1

CV > SV Relay ON : CV < SV - d Relay OFF

CV < SV Relay ON : CV > SV + d Relay OFF

OPERATIONDISPLAY

24V DC POWER ONLY

In the Programming Stage, the Display will Flash

(Not for TKP | TKM Series)

ALt = 2

ALt = 3

CV = Current Display Value = Flow Rate

SV + d > CV > SV - d Relay ON: CV > SV + d or CV < SV - d Relay OFF

SV + d > CV > SV - d Relay OFF: CV > SV + d or CV < SV - d Relay ON

SV = Selected Value = Programmed Value

d = (GPM) Hysteresis Measured around Relay Set Point (± Measured in Gallons)

6.8 General Terms

1) K : Coefficient of Flow Volume, Note : Factory Set Do Not Change

2) tr : TKM Range of Transmitter - Flow Rate 4-20 mA (4mA = 0) (20mA = Max Range)

TKP - RS 485 Option

3) NPN :

4) Con :

Transistor Relay - No Moving Parts

Output Control of Flow Total OP2,
Con = n Manual Reset,
Con = c Time Reset (1=10 Secs) Auto Reset,
Con = r Auto Reset, Based on Volume (GPM)
Con = E Pulse Output of Unit Volume,
Con = F Pulse Output of Paddle = 5 KHZ Max

Totalizer Reset TKP | TKM6HULHV

To Reset the Flow Totalizer to Zero Press

SET

 Key Hold 3 sec

SET

(PressTogether)

© Icon Process Controls Ltd. All Rights Reserved

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

07

TKS| TKP | TKM ROTATOR SERIES MANUAL

Multi-Function Paddle Wheel Flow Meter

7. Standard Pipe Size

Pipe Size (O.D.)

DN15 (½")

DN20 (3/4")

DN25 (1")

DN40 (1 ½")

DN50 (2")

2 ½

DN80 (3")

DN100 (4")

ANSI (ID) (Inches)

Sch (40) Sch (80)

0.62

0.82

1.00

1.40

2.00

2.50

3.10

4.00

0.55

0.74

0.96

1.50

1.90

2.30

2.90

3.80

DIN (ID)

(mm)

Ø20

Ø25

Ø32

Ø50

Ø63

Ø75

Ø78

Ø96.50

8. Pressure vs. Temperature (Psi, water, non-shock)

NOMINAL SIZE

INCHES mm

½-2

2-½

15-50

65

30° F
70° F

150

150

71° F

105° F

120

120

PVC

106° F
120° F

100

100

121° F
140° F

30

NA

- 5° F
85° F

150

150

PP PVDF

86° F

120° F

110

95

121° F
140° F

90

70

141° F
175° F

55

40

- 5° F
70° F

150

150

Flow Rate (LPM) / USGPM

0.3m/s min. 10m/s max.

3.5 | 1.0

5.0 | 1.5

9.0 | 2.5

25.0 | 6.5

40.0 | 10.5

60.0 | 16

90.0 | 24

125.0 | 33

71° F

105° F

125

125

106° F
140° F

100

100

120 | 32

170 | 45

300 | 79

850 | 225

1350 | 357

1850 | 357

2800 | 739

4350 | 1149

141° F
175° F

176° F
210° F

85

85

55

55

3

4

80

100

150

150

120

120

100

100

NA

NA

150

150

95

95

70

70

40

40

150

150

125

125

100

100

9. Wiring Diagram

9.1 TKP - Flow Rate + Flow Totalizer + NPN Pulse Diagram

Brown

TKP
Flow

Meter

Output

Circuit

1

4

2

5

6

3

Black

White

Yellow

Grey

Blue

Flow Rate

Totalizer

Load

Load

RS-485

Yellow & Grey with RS485 (Only) Black Wire can be Changed for Flow Total Limit Output or Unit Volume Pulse Output

9.2 TKM - (4-20mA or 0-5V DC + NPN Pulse) Flow Rate + Flow Totalizer + Pulse Diagram

Green
Brown

1

TKM
Flow

Meter

Output

Circuit

4

2

5

6

3

Black

White

Yellow

Grey

Blue

Flow Rate

Totalizer

4-20

Load

Load

+V+

A

or

+

Special Option

Ground

+V

Pulse (NPN)

Pulse (NPN)

5V DC

0V

+V

Pulse (NPN)

Pulse (NPN)

0V

Brown Yellow

Blue

White

Brown Yellow

Blue

White

10 - 30 VDC (+) (+) RS-485 (OPT)

0V (-)

Totalizer Pulse
Output NPN

Grey

Black

10 - 30 VDC (+) + (4-20mA) or (0-5V)

0V (-)

Totalizer Pulse
Output NPN

Grey

Black

(-) RS-485 1 OPT RS485
is a Special Order Item

Flow Rate Pulse
Output (NPN)

Totalizer Output NPN (4-20mA or 0 - 5V DC)
(4-20mA Default -0-5VDC Option-Special Order)

Flow Rate Pulse Output NPN

85

85

60

60

Black Wire can be Changed for Flow Total Limit Output or Unit Volume Pulse Output

© Icon Process Controls Ltd. All Rights Reserved

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

08

TKS| TKP | TKM ROTATOR SERIES MANUAL

Multi-Function Paddle Wheel Flow Meter

9.3 TKS - NPN (Flow Rate + Relay + Pulse) Diagram

Brown

1

TKS

Flow

Meter

Output

Circuit

Black Wire is a Unit Volume NPN Pulse Output-1 Pulse for every Gallon

TKP - Yellow & Grey wires with RS - 485 Option Only
Current output (4 - 20mA) : 120 max.
Voltage output (0 - 5V) : 10K min.
TKM Series (0-5VDC) Optional 4-20mA is Standard

4

5

6

3

Black

Grey

White

Blue

Load

1 AMP

+V

NO

COM

0V

Brown White

Blue

Black

10 - 30 VDC (+) COM

0V (-)

Flow Rate Pulse
Output (NPN)

Grey

NO

1 Amp

10. Installation Positions

10x 3x

10x 3x

CORRECT

CORRECT

CORRECT

INCORRECT

INCORRECT

10x 3x

INCORRECT

CORRECT

INCORRECT

10x 3x

© Icon Process Controls Ltd. All Rights Reserved

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

09

TKS| TKP | TKM ROTATOR SERIES MANUAL

Multi-Function Paddle Wheel Flow Meter

Please make sure the pipe is filled with the fluid under normal operation.
TK Series can be installed in a horizontal or vertical direction.
Please ensure enough length of straight pipe to avoid turbulence that can effect readings.

Note: Min 10x Pipe Diameters Upstream 3x Pipe Diameters Downstream.

A Plastic Basket Strainer, Bag Filter or Y Strainer Filtering Device upstream to Avoid the Paddle Wheel from being damaged by the solids
or fibers - max 10% Particle Size - Not to Exceed .5mm Cross Section or Length.
Please do not flush the pipe after the Flow Meter is installed with Compressed Air this may damage the ceramic shaft and will Void Warranty

11. Warranty, Returns and Limitations

Warranty

Icon Process Controls Ltd warrants to the original purchaser of its products that such products will be free from defects in material and

workmanship under normal use and service in accordance with instructions furnished by Icon Process Controls Ltd for a period of one
years from the date of sale of such products. I
to the repair or replacement, at Icon Process Controls Ltd option, of the products or components, which Icon Process Controls Ltd
examination determin
Ltd must be notified pursuant to the instructions below of any claim under this warranty within thirty (30) days of any claimed lack of
conformity of the product. Any product repaired under this warranty will be warranted only for the remainder of the original warranty
period. Any product provided as a replacement under this warranty will be warranted for the one year from the date of replacement.

es to its satisfaction to be defective in material or workmanship within the warranty period. Icon Process Controls

con Process Controls Ltd obligation under this warranty is solely and exclusively limited

Limitations

This warranty does not apply to products which: 1) are beyond the warranty period or are products for which the original purchaser does
not follow the warranty procedures outlined above; 2) have been subjected to electrical, mechanical or chemical damage due to
improper, accidental or negligent use; 3) have been modified or altered; 4) anyone other than service personnel authorized by Icon
Process Controls Ltd have attempted to repair; 5) have been involved in accidents or natural disasters; or 6) are damaged during return
shipment to Icon Process Controls Ltd reserves the right to unilaterally waive this warranty and dispose of any product returned to Icon
Process Controls Ltd where: 1) there is evidence of a potentially hazardous material present with the product; or 2) the product has
remained unclaimed at Icon Process Controls Ltd for more than 30 days after Icon Process Controls Ltd has dutifully requested
disposition. This warranty contains the sole express warranty made by Icon Process Controls Ltd in connection with its products. ALL

IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE EXPRESSLY DISCLAIMED. The remedies of repair or replacement as stated above are the exclusive
remedies for the breach of this warranty. IN NO EVENT SHALL Icon Process Controls Ltd BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING PERSONAL OR REAL PROPERTY OR FOR INJURY TO ANY PERSON.
THIS WARRANTY CONSTITUTES THE FINAL, COMPLETE AND EXCLUSIVE STATEMENT OF WARRANTY TERMS AND NO
PERSON IS AUT HOR IZED T O MAKE ANY OTHER WARRAN TIES OR REPRESE
Controls Ltd. This warranty will be interpreted pursuant to the laws of the province of Ontario, Canada.

If any portion of this warranty is held to be invalid or unenforceable for any reason, such finding will not invalidate any other provision of
this warranty.

NTATIONS ON BEHA LF O F Icon P rocess

© Icon Process Controls Ltd. All Rights Reserved

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

10