Page 1
1
electrical
Blink” indicates packet goes through
Blink” indicates packet goes through
Blink” indicates packet goes through
Brief introduction
Many thanks for purchasing Gigabit optical converter!
This product supports IEEE802.3Z/AB 1000Base-SX/LX
protocol, the working mode of duplex full mode and half
mode. The electric outlet is adaptive to the rate of
10/100/1000M Gigabit optical converter. T his manual is
for various models of adaptive 10Base-T, 100Base-T, and
1000Base-T optical converters. The following purchasing
guide is for customer to refer to.
Purchasing guide for Gigabit optical converters
Model Specifications
TP- LC MM 1000M adaptive, multi-mode 500 meter
TP- LC SM 1000M adaptive, single mode dual fiber 0-80 Km
Packing list
Please check the following items in the package before
the installation of converter.
Gigabit optical converter 1 piece
AC/DC adapter (external) 1 piece
User manual 1 copy
Please contact the dealer immediately for any loss or
damage to the above items.
Installation
1. Interface
RJ-45 interface
The transmission media adopts CAT5 and CAT 6
twisted-pair. It is recommended to use quality RJ-45 and
well made jumper. It features the function of
automatically identifying the through line and cross wire.
Fiber interface
If the SFP fiber transceiver you used is dual fiber type,
including two interfaces namely TX and RX. When the
two sets of optical converter are interfaced or connected
to switchboard with fiber interface, the fiber is in cross
connection, namely "TX-RX" "RX-TX".
2. Connection
Connect the network device (work station, hub or switch)
to the RJ-45 jack of the optical converter through
twisted-pair CAT5. Insert the SFP fiber transceiver in the
metal cage. Connect the multi-mode/single-mode fiber to
the SC/LC fiber interface of the SFP fiber transceiver.
Turn the power on. The corresponding LED is on for a
correct connection. (See the table below for the LED
indicator lamp)
Figure 1 Schematic drawing of connection
Explanation for LED indicator lamp
The LED indicator lamps serve as device monitoring and
error display. The following explains each LED indicator.
LED Status Explanation
SPD On The rate of the TP port is 1000Mbps
Off The rate of the TP port is 10/100Mbps
LINK/ACT Blink Active status display of
interface link
“
TP
F1 Blink Active status display of the corresponding
fiber interface link.
“
FX
F2 Blink Active status display of the corresponding
fiber interface link.
“
FX
PWR On Power is on and normal.
Redundant DIP-Switch description:
When the DIP-Switch is on the “OFF” side (Defa ult), the
2 fiber ports are working on the switch mode; When the
DIP-Switch is on the “ON” side, the 2 fiber ports are
working on the redundant mode.
When the Redundant function enabled, the F1 port work
as main channel, if the F1 port link down, the F2 port will
link up within 10ms, if the F1 port recovered, the F2 port
will link down and F1 link up within 10ms.
Page 2
2
※ Note: when the redundant function enabled, the F1
and F2 port MUST be connect to the same fiber device.
Fiber transmission features:
Product
model
TP-LC
MM
TP-LC SM 1310 -6-12 <-18 20Km
TP-LC SM 1310 -3-8 <-21 40Km
TP-LC SM 1550 0-6 <-30 80Km
1. Standard Protocol:
2. Transfer rate: Electrical interface: 10/100/1000Mbps
3 Interface: One UTP RJ-45 interface
Two metal cage for SFP fiber transceiver
4. Operation mode: full duplex mode or half duplex mode
5. Power supply parameter:
6. Environmental temperature: 0℃~60 ℃
7. Storage temperature: -40℃~85℃
8. Relative humidity: 5%-90 %( non-condensing)
Optical
wavelength
(nm)
850 -6-12 <-16 62.5μm:220meter
Technical parameters:
Optical
power
(dbm)
IEEE802.3Z/AB 1000Base-T/SX/LX
Fiber interface: 1.25Gbps
External: 5V DC 2A
Sensibility
(dbm)
Transmission
distance
50μm:550meter
9. TP cable: CAT 5E, CAT 6
10. Transfer fiber: multi-mode: 50/125, 62.5/125μm
single mode: 8.3/125, 8.7/125, 9/125 or 10/125μm
11. Dimensions: 26mm x 71mm x 95mm (H x W x D)
Cautions:
1. This product is suitable for indoor application.
2. Put on the dust cover of fiber interface when not used.
3. It is forbidden to stare at the TX fiber-transfer end with
naked eyes.
4. Single optical fiber transceiver must be used in pair
Trouble shooting:
1. Line loss is excessive during the fiber wiring
Excessive loss in adaptor connector plug-in and fiber
soldering welding and excessive intermediate nodes may
cause excessive loss rate or abnormal operation.
2. If power loss is excessive in the fiber, please check and
clean the fiber patch cord connectors.
GVT-2011
RJ45 to SFP Gigabit Media
Converter Switch, 2 x SFP, 1 x RJ45
User manual / QIG
(Please read before using the Media Converter)
V1. 0_20170727
Loading...