Leuze electronic IT 1900 User Manual

5 V
DC

A Cable entry:

depending on the cable, max. Ø 20mm,
cable-Ø 5mm

Specifications and description

IT 1900 2D-code hand-held scanner

Dimensioned drawing

en 01-2011/04 50115720

z Hand-held scanner for Data-Matrix Codes

and Bar Codes

z Large reading field for the detection of high-

contrast codes

z Robust trigger button
z Built-in decoder
z Read-display
z RS 232, USB and PS/2 interface
z Operating temperature from 0 through 50°C
z Larger reading field through higher resolu-

tion and improved decoding

Accessories

z RS 232 cable

part no. 50115105

z TTL-RS 232 cable

part no. 50114517

z PS/2 cable

part no. 50114519

z USB cable, 3m

part no. 50114521

z USB helix cable, 5m

part no. 50114523

z Power supply unit

part no. 50114525

We reserve the right to make changes • PAL_IT1900_en.fm

Electrical connection

for RS 232 cable

9-pin Sub-D Signal

2TXD 4
3RXD 5
5 GND external 3
7CTS 6
8RTS 8
9 5V DC internal 7

for USB cable

USB type A Signal IT 1900 RJ41

15VDC7
2Data -10
3Data +9
4GND3

for PS/2 cable

Mini DIN connector Mini DIN socket Signal IT 1900 RJ41

1-PC Data4
22NC
33GND3
445VDC7
5-PC Clock5
66NC

- 1 KB Data 8

-5KB Clock6

Connection for power supply

unit

IT 1900 RJ41

Leuze electronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. [phone]
[e-mail] • www.leuze.com

IT 1900 - 01

IT 1900g HD-2 IT 1900g SR-2

Typ. read distance 1) [mm]

0 200 400 600100 300 500 700

5 Mil
(0.127 mm)

Code 39

PDF 417

Data Matrix

QR Code

UPC

13 Mil
(0.330 mm)

20 Mil
(0.508 mm)

6,7 Mil
(0.170 mm)

10 Mil
(0.254 mm)

20 Mil
(0.508 mm)

Code 39

IT 1900g ER-2

1) Dependent on code module

Typ. read distance

1)

[mm]

Typ. read distance

1)

[mm]

IT 1900

Specifications

Electrical data

Operating voltage U
Power consumption max. 2,3W

B

4…5.5VDC

Interfaces

Interface type RS 232, PS/2 and USB
Trigger via button or serial command

Code types

2D codes Data Matrix ECC 200, MaxiCode, PDF417, MicroPDF, QR Code,

Bar codes 2/5 Interleaved, Code 39, Code 128, Code 93, Codabar, UPC/

Aztec, Aztec Mesas, Code 49, EAN/UCC Composite

EAN, Codablock, GS1 Databar

Optical data

Optical system high-resolution pixel array 838x640
Symbol contrast PCS 20% minimum
Light source integrated diffuse LED, wavelength 617nm ± 18nm
Read direction omnidirectional, various tilt and rotational angles

up to 45°

Mechanical data

Weight 147 g (without cable)
Dimensions 104x71 x 160 mm
Shock resistance 50 falls from a height of 1.8m

Environmental data

Ambient temp. (operation/storage) 0°C … +50°C/-40 °C … +70 °C
Relative air humidity 0 … 95% (non-condensing)
Protection class IP 41

Reading field

5 Mil

Code 39

(0.127 mm)

13 Mil

UPC

(0.330 mm)

6,7 Mil
(0.170 mm)

10 Mil
(0.254 mm)

20 Mil
(0.508 mm)

20 Mil
(0.508 mm)

Code 39

PDF 417

Data Matrix

QR Code

0 200 400 600100 300 500 700

5 Mil

Code 39

(0.127 mm)

UPC

Code 39

6,7 Mil

PDF 417

(0.170 mm)

Data Matrix

QR Code

0 200 400 600100 300 500 700

10 Mil
(0.254 mm)

13 Mil
(0.330 mm)

20 Mil
(0.508 mm)

20 Mil
(0.508 mm)

Tables

Diagrams

2D code hand-held scanner (special optics for very small codes) Part No.

IT 1900g HD-2 with RS 232, PS/2 and USB interface 50114507

2D-code hand-held scanner (standard range) Part No.

IT 1900g SR-2 with RS 232, PS/2 and USB interface 50114509

2D code hand-held scanner (special optics with large range) Part No.

IT 1900g ER-2 with RS 232, PS/2 and USB interface 50114504

IT 1900 - 01 2011/04

Order guide

Remarks

Ergonomically shaped hand­held scanner with integrated
decoder for high-contrast
codes.

Data transmission via config­urable RS 232 interface.

Or keyboard-wedge opera­tion via PS/2 or USB inter­face.

Cable latch

IT 1900

IT 1900 2D-code hand-held scanner

Switching off the computer

Information on switching off and shutting down the connected computer - which must always be performed before connecting
peripheral devices, such as a scanner - can be found in the appropriate operating instructions for your computer.

Connecting the IT 1900

Shown in the adjacent figure is the location of the cable connection and trigger
button of the scanner. The individual steps for installing the cable on the scanner
are described below.

1.To secure the interface cable to the scanner, proceed as follows:
Insert the RJ 41 connector into the socket on the bottom of the hand-held
scanner until the connector engages.
Connect the interface cable to the appropriate connection socket on the com­puter.

2.You may need a power supply unit for supplying voltage; alternatively, you can
use a cable which supplies voltage from the computer system. Use the pin
assignments (see "Electrical connection" on page 1) to select the appropriate
cable for your application.

3.Connect the power supply unit to the power socket (not necessary if voltage is supplied from the computer).

4.Check the operational readiness of the scanner by pointing the scanning sur­face towards a flat surface and pulling the trigger. A red target line as well as
the red illumination should now be visible. Now scan a sample label.
The scanner emits an audible signal to confirm that the label has been read; if
necessary, the data are now passed on to the computer.

Configuration

The hand-held scanner can always be configured using bar codes. To do this, the barcode must first be selected on the package
insert and then the trigger actuated in order to read the code. The configuration is then immediately accepted and executed.

Several of the most important configurations are listed in the following.

A second option is to configure the hand-held scanner with the USB and RS232 interfaces with the aid of the EZ Config PC
program. You can download and install this program from our homepage at www.leuze.de
The program can be used to make settings and transfer them to the hand-held scanner. The configuration can also be stored so
that it can be reused at a later time.

Further information on this can be found in the User's Guide for the IT 1900/1902.

The standard applications are described and summarised below.

Notice!

Additional information on the device and short instructions can be found on the Internet at www.leuze.de.

.

Leuze electronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. [phone] IT 1900 - 01
[e-mail] • www.leuze.com

IT 1900

Resetting the IT 1900 to factory settings

To reset all parameters to factory settings, scan the adjacent
barcode.

Attention!

All settings are lost!!!

Trigger

To activate the read process, a trigger signal is to be sent via the serial RS 232 interface or USB interface (COM port emulation
only). The command is to be sent at the set baud rate, parity, and data and stop bits.

The command for activation is: SYN T CR ASCII decimal values: 022; 084; 013

To cancel read readiness, send a deactivation.

The command for deactivation is: SYN U CR ASCII decimal values: 022; 085; 013

Following a successful read operation, the IT 1900 deactivates itself.

The second option is activation via the built-in trigger button.

Configuration for the Leuze standard protocol

Scan the adjacent 2D code.
The IT 1900 is set to the following transmission parameters:
RS 232 transmission with 9,600 baud, 8 data bits, 1 stop bit, no parity,
prefix <STX>, terminators <CR><LF>.

IT 1900 - 01 2011/04

IT 1900 2D-code hand-held scanner

Connecting the IT 1900 to the serial PC interface

With voltage supply via PIN 9 for RS232 cable (part. no. 50114517)

required parts:

1x IT 1900g XX-2

1x 50114517 KB 232-1 IT190x

With voltage supply via power supply unit with cable RS232 (part no. 50114517)

required parts:

1x IT 1900g XX-2

1x 50114517 KB 232-1 IT190x

1x 50114525 Power supply unit

Notice!

The KB 232-1 IT190x cable (part. no. 50114517) uses TTL level (0 V…5V) for data transmission. Alternatively, the
KB 232-2 IT190x cable (part. no. 50115105) can be used which works with the regular RS232 level (-12 V…+12V) and

therefore features a higher interference rejection. Both cables are connection compatible.

Procedure:

1.Switch off the PC.

2.Connect the interface cable to a free COM port (RS 232) on the computer, to the IT 1900 as well as to the power supply unit (if

present).

3.Switch the PC back on.

4.Scan the adjacent barcode.

The IT 1900 is set to the following transmission parame­ters:
RS 232 transmission with 115,200 baud, 8 data bits, 1
stop bit, no parity, terminators <CR><LF>.

5.If necessary, adjust the transmission parameters of the used COM port to those of the IT 1900.

Attention!

We recommend connecting the IT 1900 directly to a PC or to the MA 21 or MA 41… connector units. If connecting to
other components, please note that the voltage level range is maintained on the data lines!

Leuze electronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. [phone] IT 1900 - 01
[e-mail] • www.leuze.com

Connecting the IT 1900 to the MA 41 DP-K or MA 41 IS

required parts:

1x IT 1900g XX-2

1x 50114517 KB 232-1 IT190x

1x 50114525 Power supply unit

1x 50035421 KB 021 Z

1x 50033638 MA 41 DP-K for Profibus (for Interbus: 50028994 MA 41 IS

or 50030085 MA 41 IS PDP)

Pin assignments KB 021 Z:
Core colour: signal terminal in the MA 41:
brown (RXD) 2
white (TXD) 1
blue (GND) 4
red (VCC) 
black (GND) 
bare (shield) (PE) 21

Procedure:

1.Connect cable KB 021 Z to the MA 41… acc. to the above pin assignments.

2.Connect the interface cable to cable KB 021 Z.

3.Scan the adjacent 2D code.

The IT 1900 is set to the following transmission parameters:
RS 232 transmission with 9600 baud, 8 data bits, 1 stop bit, no parity, terminators
<CR><LF>.

IT 1900

Connecting the IT 1900 to the MA 21

required parts:

1x IT 1900g XX-2

1x 50114517 KB 232-1 IT190x

1x 50035421 KB 021 Z

1x 50030481 MA 21 100

Pin assignments KB021 Z:
Core colour: signal terminal in the MA 21:
brown (RXD) 26
white (TXD) 27
blue (GND) 28
red (VCC) 30
black (GND) 31
bare (shield) (PE) 21

Procedure:

1.Connect cable KB 021 Z to the MA 21… acc. to the above pin assignments.

2.Connect the interface cable to cable KB 021 Z.

3.Scan the adjacent 2D code.

The IT 1900 is set to the following transmission parameters:
RS 232 transmission with 9600 baud, 7 data bits, 1 stop bit, even parity, terminators
<CR><LF>.

IT 1900 - 01 2011/04

Disconnect

IT 1900 2D-code hand-held scanner

Connecting the IT 1900 to the MA 2xxi

required parts:

1x IT 1900g XX-2

1x 50114517 KB 232-1 IT190x

1x 50113397 KB JST-HS-300

1x MA 2xxi for the respective fieldbus system

Procedure:

1.Connect the KB JST-HS-300 cable to the system connectors in the MA 2xxi.

2.Connect the interface cable to cable KB JST-HS-300.

3.Scan the adjacent 2D code. The IT 1900 is set to the following transmission parameters:

RS 232 transmission with 9600 baud, 8 data bits, 1 stop bit, no parity, terminators
<CR><LF>.

Connecting the IT 1900 to the PS/2 interface

The operation of the IT 1900 in keyboard emulation mode is described in this section. A PC keyboard is emulated in this operating
mode. The data which are read in are written directly to the currently activated program. Thus, the data can be processed further
in all standard programs.

required parts:

1x IT 1900g XX-2

1x 50114519 KB PS2-1 IT190x

Procedure:

1.Switch off the PC.

2.Disconnect the keyboard.

3.Plug in the IT 1900 hand-held scanner between the

keyboard and the PC.

4.Switch the PC back on.

5.Scan the 2D code shown below.

Leuze electronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. [phone] IT 1900 - 01
[e-mail] • www.leuze.com

IT 1900

Connecting the IT 1900 to the USB interface (keyboard emulation)

The operation of the IT 1900 in keyboard-emulation mode on a USB port is described in this section. A PC keyboard is emulated
in this operating mode. The data which are read in are written directly to the currently activated program. Thus, the data can be
processed further in all standard programs.

required parts:

1x IT 1900g XX-2

1x 50114521 KB USB-1 IT190x (3m, straight)

or

1x 50114523 KB USB-2 IT190x (5m, spiral)

Procedure:

1.Plug the IT 1900 hand-held scanner into a free USB port.

2.The scanner acknowledges this connection with a beep.

3.Scan the adjacent 2D code.

Connecting the IT 1900 to the USB interface (COM-port emulation)

The operation of the IT 1900 as a serial interface on a USB port is described in this chapter. A COM interface is emulated in this
operating mode. The data which are read in are sent to a new COM interface. The driver with which you emulate this COM inter­face can be downloaded from our homepage at www.leuze.de. Thus, the data can be processed further in programs which expect
data via COM interfaces.

required parts:

1x IT 1900g XX-2

1x 50114521 KB USB-1 IT190x (3m, straight)

or

1x 50114523 KB USB-2 IT190x (5m, spiral)

Procedure:

1.Install the USB serial driver

(current version at www.leuze.com

2.Plug the IT 1900 hand-held scanner into a free USB port.

3.The scanner acknowledges this connection with a beep.

4.Scan the adjacent 2D code.

5.Open a terminal program or your program for the serial

interface, select the new COM port, and make the
following settings: baud rate 38,400, 8 data bits, 1 stop
bit, no parity, terminator <CR>.

).

IT 1900 - 01 2011/04