less care Ultra G Series, LBSEG3072, LBSEG3472, LBSDG3472, LBSDG3072 Installation Instructions Manual

G

SHOWER DOORS • SHOWER ENCLOSURES

INSTALLATION INSTRUCTIONS

SHOWER DOORS:

LBSDG3072
LBSDG3072+LBSEG3072
LBSDG3072+LBSEG3472

LBSDG3472
LBSDG3472+LBSEG3072
LBSDG3472+LBSEG3472

www.lesscare.com

SHOWER ENCLOSURES:

LBSDG3072+LBSEG3072
LBSDG3472+LBSEG3072
LBSDG3072+LBSEG3472
LBSDG3472+LBSEG3472

Version 4.0

SHOWER DOORS • SHOWER ENCLOSURES

ULTRA-G

PREPARATION FOR INSTALLATION

PREPARATION FOR INSTALLATION

READ ALL INSTRUCTIONS BEFORE UNPACKING THE PRODUCT

2 PEOPLE ARE REQUIRED TO LIFT AND DURING
ENTIRE INSTALLATION OF THIS PRODUCT

LessCare reserves the right to change, update, modify, alter, redesign this manual/product or its policies without prior notice!

It is your responsibility to visit website to download or contact customer service for the most updated version of the installation instructions.

LessCare shall not be liable for any injuries or property damages in connection with this product during installation or use of this product!

IMPORTANT UNPACKING INSTRUCTIONS:

When you have open top carton box lid, do not take shower glass doors or panels out before you read this and have this items in place. Have a soft
cloth blanket min ¼" thick and make sure cloth blanket is bigger then your glass doors or panels in your working area place. Set this soft cloth
blanket on the floor of working area. Take out shower glass doors or panels out from the Carton box and set it on the soft cloth blanket. Do not
lean it on the wall or floor without the soft cloth blanket.

ATTENTION! Never set glass on floor or tile or solid floor or wall surface without a soft cloth blanket if you set it without soft cloth blanket it will

cause scratches to the tempered glass and this will cause it to shatter right away or when installed or when you start using it, improper handling
causes scratches on the glass doors or panels. When installing glass doors or panels be sure your have inspected glass doors or panels fully before
installing it. Do not install and Stop installation if you see or find scratches or chipped corners on your glass doors or panels. NEVER set glass doors
or panels on its corners make sure the your floor is level with the soft cloth blanket when preparing glass doors or panels for installation.

After opening all boxes and packages, read this introduction carefully. Check that all of the needed parts are included in the package by checking
all the components on the diagram of components. Examine boxes and packages for shipping damage. If the unit has been damaged or missing
parts, please contact our customer support department immediately. Please note that LessCare will not replace any damaged products or missing
parts after 2 business days of the order receipt.

VERY IMPORTANT! Double check all glass corners and four edges of all glass door and panels to make sure that all the glass are in perfect

condition and without any scratches or chipped corners. Do not try to install the shower door, if there is any scratches or chipped corners. Note,
that you should consult your local building codes with questions on installation compliance standards. Building and plumbing codes may vary from
state to state and location. LessCare is not responsible for code compliance standards for your project and will not accept any returns. Prior to
installation, ensure that the installation surface is leveled and solid, and will be able to support the total weight of the unit. Also, make sure the
walls are at the right angles. Irregular installation surface level or improper angle of side walls will result in serious problems during installation.
Note, that some adjustments and drilling will be necessary during the installation process.

VERY IMPORTANT! Installation of this extremely heavy product to the wall requires minimum of 2" x 4" wood stud framing behind the wall.

INSTRUCTIONS THAT, IF IGNORED COULD RESULT IN SERIOUS INJURY OR DEATH

CAUSED BY INCORRECT HANDLING OR INSTALLATION OF THE PRODUCT.

THESE INSTRUCTIONS MUST BE OBSERVED FOR SAFE INSTALLATION!

LICENSED AND INSURED PROFESSIONAL CONTRACTOR IS REQUIRED TO INSTALL

THIS PRODUCT INCLUDING ASSISTANCE OF A SECOND PERSON DURING INSTALLATION

No modifications to the product are allowed. Modifications of any types to the product will result in serious injuries or may cause death.

IMPORTANT: Do not the handle on to the glass door until the instruction tells you to do so. Never lift the glass using the handle. Failure to do so will result in serious

personal injury and could cause damages to the glass. Professional graded glass suction cups are highly recommended while handling extremely heavy glass. This
product must be installed on a finished threshold and against finished walls only. This product is intended for residential use only.

TOOLS REQUIRED

Soft Cloth
or Blanket

Safety Glass LevelKnife Caulk Gun Drill Hammer

Silicone Tape

Measure

Pencil/Marker Philips/Straight

Screwdriver

OTHER TOOLS MAY BE REQUIRED

www.lesscare.com

Drill Bit

ø = 5/16"

Drill Bit
ø = 1/8"

Soft Wood

Shim

1

SHOWER DOORS • SHOWER ENCLOSURES

SHOWER DOOR MUST BE INSTALLED FIRST

SHOWER DOOR MUST BE INSTALLED FIRST

ULTRA-G

CONFIGURATION STYLES

Min. Threshold
Requirement

Min. Threshold
Requirement

Min. Threshold
Requirement

Min. Threshold
Requirement

Shower door

Please use Diagram A for assembly reference.

Pages: 6-12

Shower door with Stationary Panel (Straight Installation)

Please use Diagram A and Diagram B for assembly reference.

Pages: 6-12, 14-19

Shower Door with Stationary Panel (Enclosure Installation)

Please use Diagram A and Diagram B for assembly reference.

Pages: 6-12, 14-19

Threshold Requirement (Size): 7/8"

SAFETY IMPORTANT NOTE: Installation of shower or bathtub door requires to be installed

only on smooth and flat surface of both walls and threshold base (shower base or bathtub).

2

www.lesscare.com

DIAGRAM A

9

8

1

2

3

10

16

SHOWER DOORS • SHOWER ENCLOSURES

ULTRA-G

SHOWER DOOR COMPONENTS

MODELS:

LBSDG3072
LBSDG3472

4

6

7

11

12

13

14

5

15

Item# Item#Qty

1

Wall profile for glass door

2

Glass profile for glass door

3

Side anti-water strip

4

Upper pivot assembly

5

Lower pivot assembly

6

Anti-water strip

7

Handle

8

Bottom anti-water strip

9

Washer for screw

1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc

5 pcs

17

10

Round head screw M3.5x13

11

Screw decorative cover

12

Round head screw M5x60

13

8mm (5/16") wall anchor

14

Round head screw M4x12 with Washer

15

Countersunk Screw M4x40 (optional)

16

Countersunk screw M4x30

17

Glass door

18

Allen key (1 - 3mm, 1 - 4mm)

18

QtyDescription Description

5 pcs
5 pcs
7 pcs
7 pcs
4 pcs

1 pc

2 pcs

1 pc

2 pcs

This door has 1" out-of-plumb adjustment

www.lesscare.com

3

SHOWER ENCLOSURE/STATIONARY PANEL COMPONENTS

DIAGRAM B

19

20

23

28

29

30

26

25

21

30

24

22

GLASS

PROFILE

27

SHOWER DOORS • SHOWER ENCLOSURES

ULTRA-G

MODELS:

LBSEG3072
LBSEG3472

IMPORTANT: Stationary glass with profile has

been factory pre-assembled. Do not try to detach
the stationary glass panel with profile (20).

Item# Item#Qty

19

Wall profile for stationary glass panel

20

Stationary glass panel with profile

21

Round head screw M4x60

22

Shelf bracket (for wall)

23

Shelf bracket (for stationary glass panel)

24

Glass shelf

1 pc
1 pc

7 pcs

4 pc
2 pc
2 pc

25

Washer for screws

26

Round head screw M3.5x13

27

Screw decorative cover

28

Countersunk screw M5x30

29

Bottom bracket

30

8mm (5/16") wall anchor

QtyDescription Description

4 pcs
4 pcs
4 pcs
1 pcs
1 pcs
8 pcs

This panel has 1" out-of-plumb adjustment

4

www.lesscare.com

4A

4B

SHOWER DOORS • SHOWER ENCLOSURES

ULTRA-G

PIVOT ASSEMBLY COMPONENTS

4D

4

4C

5C

5E

4E

5F

4F

Item# QtyDescription

4A

Upper Pivot retainer

4B

Countersunk screw M6x14

4C

Pivot body

4D

Plastic washer

4E

Gasket

4F

Back plate

4G

Countersunk screw M6x14

5D

4G

1 pc
1 pc
1 pc
2 pc
2 pc
1 pc
2 pc

5

5G

Item# QtyDescription

5A

5B

5A

Lower Pivot retainer

5B

Countersunk screw M6x14

5C

Pivot body

5D

Plastic washer

5E

Gasket

5F

Back plate

5G

Countersunk screw M6x14

1 pc
1 pc
1 pc
2 pc
2 pc
1 pc
2 pc

Upper Pivot Assembly and Lower Pivot Assembly Disclaimer

Upper and lower pivot assemblies are reversible. For left opening installation Upper Pivot Assembly (4) is used as upper pivot and
Lower Pivot Assembly (5) as lower pivot. If you plan to open shower door to the right side, use Lower Pivot Assembly (5) as upper
pivot and Upper Pivot Assembly (4) as lower pivot.

NOTE: After installation of all pivots you will have one Countersunk screw M6x14(5B or 4B) unused, because only installation of top

pivot requires that screw. Countersunk screw M6x14(5B or 4B) is optional during Installation of Lower pivot assembly (5 or 4) .

www.lesscare.com

5

SHOWER DOORS • SHOWER ENCLOSURES

ULTRA-G

INSTALLATION STEPS

Single Shower Door Assembly
and Installation

NOTE: Use parts from Diagram A for Single

Shower door assembly and installation.

a

1

+0.0

b

1

c

Installation requires
minimum of 2" x 4"
wood stud framing
behind the wall.

d

13

Shower Base

Figure 1

1. Wall profile and Pivot retainers installation

1.1 Place the Wall Profile For Glass Door (1) vertically against the wall

and set it to the shower base or the threshold.

Using a level to level the wall profile upright mark 7 pre-drilled holes on
the wall, using a pencil or marker, to prepare for drilling.

Now, drill 7 holes in the wall using 8mm (5/16") Drill Bit. Apply silicone
into the holes on the wall. Insert seven 8mm (5/16") Wall anchors (13)
and hammer them in.

See Figure 1 for details

6

www.lesscare.com