Lesro Fremont Chair, Fremont Sofa, Fremont Loveseat Assembly Instructions Manual
Assembly Instructions
fig 3
Leaders in Reception Seating
Lesro Industries, Inc.
1 Grifn Road South
Bloomeld, CT
06002
Phone
860.243.3226
Fax
860.243.5392
www.lesro.com
1. Unpack and identify all parts.
2. Lay back on a soft clean surface
as shown in gure 1.
3. Attach seat to back using 2”
bolts and washers into threaded
inserts, as shown in gure 2.
4. Align bottom edge of seat with
bottom edge of back.
5. Tighten bolts securely.
For Fremont Chairs, Loveseats and Sofas
Tools required: Phillips head screwdriver and 9/16” ratchet or wrench. (Ratchet recommended.)
Note: These instructions are intended for various models and congurations. Your products may not
look exactly as those shown in the diagrams.
Important: The assembly process requires that some hardware be kept loose until later in the
sequence. Follow these instructions closely to ensure correct assembly.
Recommendation: Retighten all bolts on a seasonal basis to ensure your product remains strong and
stable for many years of use.
Weight Capacity: All Fremont guest chairs have a weight capacity of 500 lbs. per seat, bariatric
chairs 750 lbs., loveseats 600 lbs., and sofas 700 lbs., unless otherwise stated.
Section 1 - Chairs, Loveseats and Sofas without Arms
Hardware Pack
2” Hex Bolts
Washers
1 ½” Phillips Screws
2” Bolts
6. Insert Phillips screws through pre-
drilled holes in plywood, as shown
in gure 2. Tighten securely using
care not to strip.
7. Your product is now assembled
and ready to use.
1. Follow instructions in Section 1
to attach seat to back. Be sure
bottom edge of seat is aligned
properly with bottom edge of back
when tightening bolts.
2. Attach arms to seat and back using
3” bolts and washers into threaded
inserts, as shown in gure 3. Start
each bolt rst, until all have caught
a few threads, then nger tighten
only. Hint: start with bolt in back
cushion rst, followed by front
seat bolt, then middle bolt last.
3. Align bottom edges of seat and
arms. Also align back edges of
arms and back cushion.
4. Tighten all bolts securely.
5. Your product is now assembled
and ready to use.
Align edges when
tightening bolts
Figure 2Figure 1
Section 2 - Chairs, Loveseats and Sofas with Arms
Figure 3
3” Bolts
Hardware Pack
2” Hex Bolts
3” Hex Bolts
Washers
1 ½” Phillips Screws
3” Bolts
Align all edges when
tightening bolts
Thank you for purchasing a Lesro product.
Need assistance with assembly? Call Lesro customer service 1-800-275-7545.
© 2015 Lesro Industries, Inc. Jun 2015
Visit us on-line at www.lesro.com
Assembly Instructions
Leaders in Reception Seating
Lesro Industries, Inc.
1 Grifn Road South
Bloomeld, CT
06002
Phone
860.243.3226
Fax
860.243.5392
www.lesro.com
Hardware Pack
2” Hex Bolts
3” Hex Bolts
Washers
1 ½” Phillips Screws
For Fremont Chairs, Loveseats and Sofas
Tools required: Phillips head screwdriver and 9/16” ratchet or wrench. (Ratchet recommended.)
Note: These instructions are intended for various models and congurations. Your products may not
look exactly as those shown in the diagrams.
Important: The assembly process requires that some hardware be kept loose until later in the
sequence. Follow these instructions closely to ensure correct assembly.
Recommendation: Retighten all bolts on a seasonal basis to ensure your product remains strong and
stable for many years of use.
Weight Capacity: All Fremont guest chairs have a weight capacity of 500 lbs. per seat, bariatric
chairs 750 lbs., loveseats 600 lbs., and sofas 700 lbs., unless otherwise stated.
Section 3 - Connecting Chair with Center Arms
Figure 4
3”
2”
Bolts
Bolts
3”
Bolts
2”
Bolts
1. Follow instructions in Section 1 to attach seats to backs using
2” bolts. Be sure bottom edges of seats are aligned properly
with bottom edges of backs when tightening.
2. Identify left, right, and center arm pieces. Center arms have bolt
holes on both sides. Left and right arms have bolt holes on one
side only.
3. Orient chairs and arms side-by-side, as shown in gures 4 and 5.
4. Attach outside arms to seats and backs using 3” bolts and
washers into threaded inserts, as shown in gure 4.
5. Attach center arms to seats and backs using 2” bolts and
washers into threaded inserts, as shown in gure 4.
6. Start each bolt rst, until all have caught a few threads, then
nger tighten only. Hint: start with bolt in back cushion rst,
followed by front seat bolt, then middle bolt last.
7. Align bottom edges of seats and arms. Also align back edges of
arms and back cushions.
8. Tighten all bolts securely.
9. Your product is now assembled and ready to use.
Align all edges when
tightening bolts
Figure 5
Thank you for purchasing a Lesro product.
Need assistance with assembly? Call Lesro customer service 1-800-275-7545.
© 2015 Lesro Industries, Inc. Jun 2015
Visit us on-line at www.lesro.com
Loading...