Le Shi Zhi Xin Electronic Technology LEUBP 201E User Manual

45mm

How to connect via Bluetooth

Step 1.

Press the buon for 3 seconds and the LED indicator will
glow blue, indicang that the selfie sck is powered on.
When the indicator flashes blue, the device is in the
Bluetooth pairing mode (if it has never been connected)
Reconnecng mode (auto connecng to a paired device
in 5 seconds)

Step 2.

Turn on Bluetooth on the phone, search for “letv-ZPG”,
and tap it to auto pair and connect. When connected, the
indicator on the selfie sck will glow blue, and the
photo-taking mode is ready to use

Step 3.

Place the phone into the bracket, launch Camera on the

phone, and press the selfie buon to take photos/record

videos

(The indicator glows red during charging and goes off
when fully charged)

(The indicator glows blue when powered on and

flashes blue when pairing)

How to use the Letv selfie sck

Press for 3 second to power on

4

Press the selfie buon
to take photos/record

Bluetooth connecon

*

We suggest you to remove the phone case when using this device.
Do not twist the selfie sck using extra force.

videos

5

Press for 3 second to power off

6

85mm

LeUBP-201E

Product

Weight: 173g Extended length: 66cm

Materials: aluminum, plasc

Packing dimensions: 213x61x41mm

In the Box: selfie sck x1 lanyard x1

user manual x1 3R warranty cerficate x1

data cable x1

Baery

Capacity: 65mAh Standby me: 3 days
Working me: 30H Charging voltage: 5V
Input current: 300MA-2A Charging me: 1.5H
Charge cycles: ≥ 300

Notes

1. Store and use the product in normal temperature.

2. Do not expose this product to rain and water or use in
a wet environment.

3. Do not throw the product to avoid damage.

4. Do not use chemical solvents to coat or wipe the
product.

5. The maximum weight capacity of the phone bracket
and connecng rod is 1kg.

6. Do not use the selfie sck where you are not
prohibited.

7. Check it in as luggage when taking a flight.

Kind noce: If the Letv selfie sck is not connected to a phone 10

minutes aer it is powered on, the indicator will go off and the selfie

sck will go into the hibernaon mode. In the photo-taking mode, the

indicator will go off and the selfie sck will go into the hibernaon

mode if idle for 24 hours. If the connected phone goes out of range

(10m in tesng environment), the selfie sck will go into the

hibernaon mode. You can wake it up by pressing the selfie buon.

The statements should be displayed in the user manual:
changes or modifications not expressly approved by the
party responsible for compliance could void the user’s aut­hority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Oper­ation is subject to the following two conditions: (1) this dev­ice may not cause harmful interference, and (2) this device
must accept any interference received, including interferen­ce that may cause undesired operation.

This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide re­asonable protection against harmful interference in a resid­ential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and use­d in accordance with the instructions, may cause harmful i­nterference to radio communications. However, there is no
guarantee that interference will not occur in a particular ins­tallation.
If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following m­easures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and
receiver.

-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician
for help.