Leonton EG5-0804-SFP Series, EG5-0804-SFP, EG5-0804-SFP-T, PG2-1802-SFP Series, PG2-1802-SFP User Manual

LEONTON

EG5-0804-SFP Series

(EG5-0804-SFP / EG5-0804-SFP-T)

User Manual

© Copyright 2016 LEONTON Technologies, Co. Ltd.
All Rights Reserved
This document contains information, which is protected by copyright. Reproduction, adaptation or
translation without prior permission is prohibited, except as allowed under the copyright laws.

Disclaimer

LEONTON Technologies, Co. Ltd. provides this manual without warranty of any kind, expressed or
implied, including but not limited to the implied warranties of merchantability and fitness for a
particular purpose. LEONTON Technologies, Co. Ltd. may make improvements and/or changes to
the product and/or specifications of the product described in this manual, without prior notice.
LEONTON Technologies, Co. Ltd. will not be liable for any technical inaccuracies or typographical
errors found in this guide. Changes are periodically made to the information contained herein and
will be incorporated into later versions of the manual. The information contained is subject to
change without prior notice.

FCC Notice

This equipment has been tested and found to comply with the limits for a Class-A digital device,

pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy. It may cause harmful interference to radio communications if the

equipment is not installed and used in accordance with the instructions. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

•

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver

•

is connected.
Consult the dealer or an experienced radio/TV technician for help.

•

Caution: Any changes or modifications not expressly approved by the grantee of this device could

void the user's authority to operate the equipment.

CE Mark Warning

This is a Class-A product. In a domestic environment this product may cause radio interference in

which case the user may be required to take adequate measures.

This document is the current official release manual. Please check our website (www.leonton.com)

for any updated manual or contact us by e-mail ([e-mail]).

Contents

Overview ..................................................................................................................... 1

Software Features ................................................................................................. 1

Hardware Features ................................................................................................ 1

Package Contents .................................................................................................. 2

Safety Precaution .................................................................................................. 2

Hardware Description ................................................................................................. 4

Physical Dimensions .............................................................................................. 4

Front Panel ............................................................................................................ 5

Top View ............................................................................................................... 5

LED Indicators ....................................................................................................... 6

Ethernet Ports ....................................................................................................... 7

Cabling .................................................................................................................. 8

Wiring the Power Inputs...................................................................................... 10

Wiring the Fault Alarm Contact ........................................................................... 11

Grounding Note ................................................................................................... 12

Mounting Installation ............................................................................................... 13

DIN-Rail Mounting ............................................................................................... 13

Wall Mounting .................................................................................................... 15

Hardware Installation ............................................................................................... 16

Installation Steps ................................................................................................. 16

Maintenance and Service .......................................................................................... 17

Trouble Shooting ...................................................................................................... 18

Overview

Software Features

Layer 3 Switching

Static Routes

Management

CLI, Http, Https, SNMP, SSH, Telnet

Access Management, ACL, ARP Inspection, DHCP Snooping, IP Source

Private VLAN, Protocol-based VLAN, GVRP

Green Ethernet

IEEE 802.3az EEE (Energy Efficient Ethernet)

Network Reliability

STP, RSTP, MSTP, ERPS (G.8032)

Multicast

IGMP snooping, MLD snooping, MVR

Traffic Control

LACP, QoS (CoS/To S )

Monitor

LLDP, LLDP-MED, Port Mirroring, RMON, MIB, sFlow, Syslog Server

DHCP

DHCP Server/Client/Relay/Snooping

Other

ICMP Ping, ICMPv6 Ping, Loop Protection, Storm Protection, NTP Client

PoE Management
(For PoE Models)

This series is rated IP30 and installation by DIN Rail. Each unit of this industrial gigabit managed

Ethernet switch series has 4 10/100/1000Tx Gigabit Ethernet ports and 4 dual-rate (100/1000)

SFP slots, suitable for applications that require high bandwidth and long distance communication.

In order to prevent unregulated voltage, this series provides high EFT and ESD protection. This

also allows it to function in harsh environments, as well as support power redundancy with a dual

power input design with reverse polarity protection. The built-in relay warning function alerts

users about occurring power failures.

With one model having an operating temperature of -10 to 65°C, and another with a wide

operating temperature of -40°C ~ 75°C, this series is designed to meet any needs for industrial

automation, outdoor application and harsh environments.

Software Features

Security

Guard, Multiuser Account, Port Security Limit Control, RADIUS,
TACACS+, 802.1Q VLAN, IP Subnet-based VLAN, MAC-based VLAN,

PoE Alive Check, PoE Power Budget Managed, PoE Scheduled

Hardware Features

Interface & Performance

• All Copper ports support auto MDI/MDI-X function

• Embedded 4*10/100/1000Tx Gigabit Ethernet and 4*100/1000 SFP Slots

• Store-and-forward switching architecture

• 8K MAC Address Table

• Supports 9.6Kbytes Jumbo Frame

1

• 4Mbits memory buffer

Power Input

• Redundant power DC 12~48V with connective 1*6-pin removable terminal block

• Max. current 3.5A

• Relay Contact: 24 VDC, 1A resistive

• The power input specification is complied with the requirements of SELV (Safety Extra Low

Voltage), and the power supply should be complied with UL 61010-1 & UL 61010-2-201

Certification

• CE/FCC

• UL 61010-1

• UL 61010-2-201

Operating Temperature

• Standard operating temperature model: -10°C ~ 65°C

Extended operating temperature model (–T): -40°C ~ 75°C

•

Case/Installation

• IP30 protection

• Installation in a Pollution Degree 2 industrial environment

• DIN-Rail and Wall mount design

Package Contents

• 1 - EG5-0804-SFP(-T): 8-port industrial gigabit managed Ethernet switch, with

4*10/100/1000Tx Gigabit Ethernet and 4*100/1000 SFP Slots

2 - Wall mounting brackets and screws

•

1 - RJ45 to DB9 Serial Console cable

•

Safety Precaution

Attention

If the DC voltage is supplied by an external circuit, please use a protection device on the power

supply input. Supply by UL Listed industrial use power. The industrial Ethernet switch’s hardware

specs, ports, cabling information, and wiring installation will be described within this user manual.

2

Warning Labels

The caution label means that you should check the certain information on user manual when

working with the device. (Shown in Figure 1.1)

Figure 1.1: Caution Label

This warning label is on the device, and means that the surface of the device is hot. (Shown

in Figure 1.2)

Figure 1.2: Hot Surface Warning Label

3