Leone ZN-12M12, ZN-12M16 Operating Instructions And Parts Manual

OPERATING INSTRUCTIONS AND PARTS MANUAL

MODEL ZN-12M12

Decorative Nailer

CAREFULLY READ THIS MANUAL BEFORE OPERATING TOOL

APLUS Pneumatic Corp.

NO.579, SEC. 1, SHEN LIN RD., TAY A,TAICHUNG HSIEN 428 TAIWAN, R.O.C.

Tel: [phone] Fax: [phone]

Original instructions

TOOL SPECIFICATIONS

MODEL OF TOOL .................................................................. ZN-12M12

TOOL LENGTH ....................................................................... 9.06" (230 mm)

TOOL HEIGHT ........................................................................ 7.09" (180 mm)

TOOL WIDTH .......................................................................... 2.76" (70 mm)

WEIGHT (WITHOUT FASTENERS) ...................................…1.65 lbs (0.75 kg)

AIR INLET ............................................................................... 1/4" NPT

COMPRESSED AIR :

Maximum permissible operating pressure ............................. 110 PSIG (7.5 bar)

Recommended operating pressure range ........................….. 65∼90 PSIG (4.5∼6 bar)

AIR CONSUMPTION.............................................................. 0.0043 scfm with 25

nails per minute
@ 90 psi (6.2 bar)

Noise dB(A)：
A-weighted sound pressure level LpA……………….……….. 80.52 dB(A)
A-weighted sound power level LwA………………….……. .… 93.52 dB(A)
Measurement uncertainty: 3dB
Vibration (m/s

2

)：

Hand-arm vibration value…………………………………..….. 1.9 m/s

2

Measurement uncertainty: 1.5 m/s2

Warning:

The vibration emission during actual use of the power tool can differ from the declared t otal
value depending on the ways in which the tool is used; and of the need to identify safety
measures to protect the operator that are based on an estimat ion of exposure in the actual
conditions of use (taking account of all parts of the operation cycle such as the times when
the tool is swit ched off and when it is running idle i n addition to the trigger time).

List of fasteners for ZN12M12：

Crown Length MAGAZINE

ψ11.8 mm , ψ0.46 " 9.0 mm ~ 19 mm , 0.35 " ~ 0.74 " 1 pcs

Foreword:
This pneumatic nailer is designed for using on soft mater ial or driving tacks/decorative nails
into wood. Its well balanced, ergonomic and comfort non-sl ip cushioned grip ensure you a
satisfactory tackle and improve work efficiency. One of features is to drive different si zes of
loose nails. No more painful hammering.

Suitable applications:

Leather upholstery, shoes, antique, trimming mattres ses

Caution:

Staplers are only applying on wood. Not suitable for stapling or nailing into concrete,
masonry bricks or steel. Do not fire if staples are jammed, as this will cause damage to the
relevant parts.

DANGER

Indicates an imminently hazardous s ituation which, if not avoided, will result in death or
serious injury.

WARNING

Indicates an potentially hazardous situation which, if not avoided, will result in death or
serious injury.

NOTE

Alerts the operator to useful information.

SAFETY INSTRUCTIONS

DANGER

1. Read this manual and underst and all safety instructions before operation the tool. If you
have any questions, please contact our authorized representatives.

2. Only those fasteners listed in the operating instructions may be used in the fastener driv­ ing tools.

3. Only the main energy and t he lubricants listed in the operating instructions may be used.

4. Fastener drivi ng tools marked with an inverted equil ateral triangle standing on one point
may only be used with an eff ective safety yoke.

5. Fastener drivi ng tools equipped with contact actuation or continuous contact actuation,
marked with the symbol " Do not use on scaffoldings, ladders", shall not be used for spe­ cific applic ation for example:

─when changing one driving locat ion to another involves the use of scaffoldings, stairs ,

ladders, or ladder alike constructions, e.g. roof laths,

─closing boxes or crates,
─fitting transportation safety systems e.g. on vehicles and wagons.

6. For the maintenance of f astener driving tools, only spare parts specified by the manufac­ turer or his author ized representative shall be used.

7. Repairs shall carried out by agents authorized by the manufacturer or by other specialis­ ts, having due regard to the information given in the operati ng instruction.

8. Stands for mounting t he fastener driving tools to a s upport for example a work table shall
be designed and constructed by the stand manufacturer in such a way that the fastener
driving tool can be safely fixed for the intended use, thus for example avoiding damage,
distortion or displacement.

9. Fastener drivi ng tools operated by compressed air shall only be connected to compres s­ ed air lines where the maximum allowable pressure cannot be exceed by a factor of
more than 10%, which can for example be achieved by a pressure reduction valve
which includes a downstream safety valve.

10. When using fastener dr iving tools operated by compressed air, particular attenti on must
be paid to avoid exceeding t he maximum allowable pressure.

11. When using fastener driving tools operated by compres sed air should only be operated
at the lowest pressure required for the work proces s at hand, in order to prevent unnece­ ssarily high noise levels, increased wear and r esulting failures.

12. Hazards caused by fire and explosion when using oxygen or combustible gases for ope­ rating compressed air operated fastener driving tools.

13. Carry the fastener driving tool at workpiece using only the handgrip, and never with t he
trigger actuated. Never carry the tool by the hose or pull the hose to move the tool.

14. Disconnect the t ool from air supply before cleaning j ams,
servicing, adjusting, and during non-operation.

15. Wear eye protecti on.

16. Do not use a check v alve or any other fitting whic h allows

air to remain in the tool.

17. Do not place your hand or any part of your body in the
fastener discharge area of the tool when connecting or

disconnecting air supply.

18. Never point tool at yourself or at any other person.

AIR SUPPLY AND CONNECTION

NOTE

•Many air tool users f ind it convenient to use oiler t o help provide oil
circulation t hrough tool and increase the effici ency and useful life
of the tool. Check oi l level in the oiler daily.

•Many air tool user find it convenient to use a filter to remove liquid
and impurities which can rust or wear internal parts of the tool. A
filter also increase the efficiency and us eful of the tool. The filter
must be checked on a daily basis and if necessary drained.

•For better performance, install a 3/8" quick connector (1/4" NPT
threads) with an ins ide diameter of .315" on your tool and a 3/8"
quick coupler on the air hose.

The following illustration shows the correct mode of connection to the air
supply system which will increase the efficiency and useful life of

the tool.

LUBRICATION AND MAINTENANCE

NOTE

•Disconnect the air s upply from the tool before lubricating.

•Your tool requires lubrication before you use it for t he first time.

•Wipe off excessive oil at the exhaust. Excessive oil will damage

O-rings of tool. If in-line oiler is used, manual lubrication through

the air inlet is not required on a daily basis.

•Turn the tool so the inlet is facing up and put one drop of high

speed spindle oil, UNOCAL RX22, or 3-IN-1 oil into air inlet. Nev er
use detergent oil or additives. Operate the tool brief ly after adding
oil.

connector

Quick

Quick

coupler

Regulator

coupler

Quick

connector

Air hose

Quick

Oiler

Filter

comp ressor