AM/FM DIGITAL RADIO
CD PLAYER WITH 60 SECOND ESP PLUS
ANTI-SKIP PROTECTION
MODEL CD-915
OPERATING INSTRUCTIONS
TM
DIGITAL AM/FM RECEIVER
•
5 AM & 5 FM PRESET STATION BUTTONS
•
PLAYS MUSIC COMPACT DISCS
•
RADIO & CD VISUAL DISPLAY
•
TRACK REPEAT & DISC REPEAT
•
60 SECOND ESP PLUS
•
USES 2 SIZE “AA” BATTERIES (NOT INCLUDED)
•
LINE OUT JACK - CONNECTS TO YOUR STEREO SYSTEM
•
PLEASE READ CAREFULLY BEFORE USE
TM
(ELECTRONIC SKIP PROTECTION) SYSTEM
IB-CD915(CDR25J-60K8)-WM-E-042004
LOCATION OF CONTROLS
6
5
4
3
2
1
7
8
9
10
11
12
14
1.RADIO AM/FM BAND BUTTON
2.RADIO MEMORY BUTTON
13
15
16
17
3.CD PROGRAM BUTTON (FOR PROGRAMMED PLAY)
4.CD REPEAT BUTTON
5.CD STOP AND POWER OFF BUTTON
6.CD AND RADIO DISPLAY
7.CD PLAY/PAUSE BUTTON
8.CD FORWARD SEARCH/RADIO TUNING UP BUTTON (SKIP/TUNING)
9.CD BACKWARD SEARCH/RADIO TUNING DOWN BUTTON (SKIP/TUNING)
10.AM & FM RADIO PRESET BUTTONS (PRESET)
11.CD DOOR
12.LINE OUT JACK (FOR HOME STEREO CONNECTION)
13.VOLUME CONTROL
14.CD DOOR OPEN BUTTON (SLIDE TO OPEN)
15.BASS BOOST SWITCH
16.CD/RADIO FUNCTION SWITCH
17.PHONES JACK (headphone jack)
18.BATTERY DOOR
19.AC ADAPTOR JACK (AC ADAPTOR NOT INCLUDED)
1
IB-CD915(CDR25J-60K8)-WM-E-042004
19
18
POWER SOURCES
Power your CD player by connecting an optional AC ADAPTOR or by inserting 2 size “AA”
fresh alkaline batteries.
NOTE:Before you buy an optional AC Adaptor, please note, the only AC ADAPTOR
suitable for this player is DC 4.5V 700mA, with polarity , others may damage
your player. Please check voltage and current (mA) before buying an AC ADAPTOR.
Using with Batteries
Insert two size “AA” alkaline batteries
according to the + and - markings on
the bottom of the set.
TIPS ON BATTERY USE
Reversing polarities will damage the batteries and possibly your set. Be sure to
•
follow polarity ( + and - ) as indicated.
Do not mix different types together (Alkaline, Carbon-Zinc, Nickel-Cadmium etc.),
•
or old batteries with new ones.
When not in use for an extended period of time, or while internal batteries will not
•
be used, remove them to prevent possible acid leakage or corrosion resulting in
damage to your player.
When the batteries have become discharged, they must be disposed of in a safe
•
manner that complies with all applicable laws.
Installation of batteries should only be done by an adult (for safety).
•
ALKALINE BATTERY LIFE
Bear in mind that battery life expectancy is based upon volume and bass listening
levels.
Maximum battery power consumption happens at maximum settings. Typical life
for 2 size “AA” alkaline batteries is above 8 hours of continuous CD play and 5
hours longer for radio use.
WHEN
While CD is playing, if the alkaline batteries are weak or discharged, this symbol
“ ” shows or flashes in the display, then the power automatically turns off. If
this occurs, replace both alkaline batteries (also if the display does not show
anything, the batteries are dead).
NOTE 1: The radio may work normally for about 5 hours when “ ” shows or
NOTE 2: You may use rechargeable batteries on this set. However, because
SHOWS IN THE DISPLAYY
flashes in the display indicating batteries are weak for CD play, but still
OK for the radio.
rechargeable batteries generally have lower voltage (1.2 volts instead of
1.5 volts). Your playing time will be much less than normal fresh alkaline
batteries.
2
IB-CD915(CDR25J-60K8)-WM-E-042004
CONNECTING TO HOME STEREO SYSTEMS
The LINE OUT jack is made to accept a stereo mini plug (3.5mm). Simply connect the
cable’s mini plug to the LINE OUT jack on your player, and the other appropriate end
usually RCA JACKS to the CD/AUX INPUTS of your home stereo.
YOUR CD PLAYER
YOUR STEREO
SYSTEM
OPTIONAL CABLE (3.5mm)
TO RCA JACKS
TO AUX IN JACKSTO LINE OUT JACK
3
IB-CD915(CDR25J-60K8)-WM-E-042004
CD PLAYING
1 Slide the CD/RADIO FUNCTION switch to CD position
(at the bottom of the set).
2 Load the Disc.
Push
here
Disc
LABEL SIDE UP
3 Connect the Headphones.
Stereo
headphones
4 Press the PLAY/PAUSE Button.
TRACK NUMBER
CURRENTLY
NOTE:The ESP PLUS
button is pressed.
PLAYING
ELAPSED PLAYING
TIME OF THE
CURRENT TRACK
TM
function will turn on automaically when the PLAY/PAUSE
5 Adjust the Volume.
SLIDE RIGHT TO OPEN
TO PHONES
PLAY/PAUSE
BUTTON
VOLUME CONTROL
MAXIMUM MINIMUM
4
IB-CD915(CDR25J-60K8)-WM-E-042004
OTHER OPERATIONS
Operation Press
To pause play
To release pause
and resume play
To stop
To turn off the power
To skip to the next track(s)
To skip to the previous track(s)
To go ahead at high speed
(search)
PLAY/PAUSE
button
PLAY/PAUSE
button
STOP button
STOP button once and wait 30 seconds, or press
STOP button twice.
SKIP/TUNING FORWARD button once (or
repeatedly).
SKIP/TUNING BACKWARD button once (or
repeatedly).
Keep SKIP/TUNING FORWARD button
depressed and release when the desired music
section of the disc is found.
Display window shows
TRACK NUMBER
CURRENTLY PLAYING
TRACK NUMBER
CURRENTLY PLAYING
TOTAL TRACKS
PLAYING TIME
FLASHES
PLAYING TIME
ADVANCES
TOTAL PLAYING TIME
To go back at high speed
(search)
Keep SKIP/TUNING BACKWARD button
depressed and release when the desired music
section of the disc is found.
BASS BOOST switch
This switch enhances the low frequency (bass)
sounds at low listening levels. Switch the BASS
BOOST switch (on the bottom of the set) ON or
OFF to suit your taste.
5
BASS BOOST switch
IB-CD915(CDR25J-60K8)-WM-E-042004
REPEAT, INTRO AND RANDOM PLAY
You may have repeat, intro or random play using the REPEAT button. Press the
REPEAT button several times, and the display will show the followings in turn:
REPEAT ONE
-->
REPEAT ALL
-->
INTRO
-->
RND
-->
Single Track Repeat
Plays one song over and over till you press STOP.
During play, select the song you want to repeat with
either of the SKIP/TUNING buttons ( or ), then
press the REPEAT button once, the symbol
appears in the display.
The song currently playing will repeat over and over,
until you press STOP.
REPEAT ONE
All Tracks Repeat (Disc Repeat)
Repeats all songs in order, till you press STOP.
During play, press the REPEAT button twice, the symbol
REPEAT ALL
All songs will keep playing in sequence 1, 2, 3, etc. and
when finished, will start all over again until you press the
STOP button.
will show in the display.
Intro Play
This plays the first 10 seconds of songs in sequential
order.
1.During play, press the REPEAT button three times,
the word
2.Press the PLAY/PAUSE button, the word
stop flashing and the first 10 seconds of each song
on the CD will play in sequential order.
3.When you find a song you like, press the PLAY/PAUSE
button, normal play will be resumed, that song (and
the following songs) will play NORMALLY .
INTRO
will flash in the display.
INTRO
will
NORMAL PLAY
Random Play
This plays the songs on the disc in a random order.
1.During play, press REPEAT button four times the word
RND
will flash.
2.Press the PLAY/PAUSE button, this will play all of the
songs in random order selected by the CD player.
The word
3.Press the SKIP/TUNING button , to skip to the
next random song.
RND
will stop flashing.
6
IB-CD915(CDR25J-60K8)-WM-E-042004
PROGRAMMED PLAY
The tracks (songs) on the disc can be programmed (arranged in advance) to play in
any order you prefer (up to 20 tracks can be programmed).
Programming Example:
Program Number
Track Number (song number)
During programming, the word
in your preferred order, follow steps below:
1.Press the PROGRAM button.
The word
2.Press the SKIP/TUNING button (
or ) to select track number 3
(example).
PROG
will flash in the display.
Program number
PROG
will flash in the display.
1
2 3 4 5 6 7 8
3
5
PROG
flashes in the display. To program songs to play
etc.
8 1 2 4 1 1
3.Press the PROGRAM button to confirm.
Track 3 is now programmed.
Program number 2 will now show in the
display, ready for your next selection of
track.
4.Repeat steps 2 and 3 to program other
tracks till you finish (up to 20 selections).
5.After programming is finished, press
PLAY/PAUSE to begin programmed
play.
PROG
display, and music begins.
NOTE:
-The player will stop automatically after
all programmed tracks have been
played.
- To quit programmed play, press STOP
button once. Then you may press PLAY/
PAUSE button to re-start normal play.
changes to be steadily in the
etc.
Track number
Your programmed memory will be
lost:
When the alkaline batteries are
•
exhausted or removed, or the optional
AC ADAPTOR is disconnected.
When the power is off.
•
7
IB-CD915(CDR25J-60K8)-WM-E-042004
60 SECOND ESP PLUSTM ANTI-SKIP SYSTEM
This set is designed with the latest 60 second ESP PLUS
- which allows virtually unlimited gentle skip protection above the normal shock
protection.
The 60 second ESP PLUSTM function prevents the sound from skipping by using a
buffer memory that stores music data. The new 60 second ESP PLUSTM system can
store more music than normal anti-skip systems.
This new design allows gentle swaying of the set (as in walking) without music skipping.
This function (CD ESP PLUSTM) may not work during heavy jogging.
The 60 second ESP PLUSTM function will turn on automatically
when the PLAY/PAUSE button is pressed.
When the PLAY/PAUSE button is pressed, the “ ” (memory
basket) indicator will appear in the display, the digital data (music)
is stored in the “read-ahead” memory buffer before it is decoded
and played.
The “ ” mark changes to the “ ” mark, indicating that the
memory buffer (basket) is full.
When the set is subject to a shock or a bump during play, the
•
data stored in memory continues to be decoded and played.
This gives the pickup time to stabilize and continue reading
new music. As the data is used from memory, the indicator
changes from “ ” to “ ”. Once the pickup returns to its
original position, new data is stored in memory and the display
changes back to the “ ” mark.
If the set is subject to repeated shocks and all the data stored
•
in memory is used up, the “ ” mark is displayed and the
sound will skip or stop for a brief period until the memory basket
has time to fill up again.
TM
(Electronic Skip Protection)
EMPTY MEMORY
FULL MEMORY
SOME MEMORY USED
NOTE:
- The music may stop if the player receives continuous shocking.
-You may hear noise or skipping if the CD is dirty or scratched.
-If you press SKIP/TUNING buttons, the memory basket will
empty itself temporarily.
8
IB-CD915(CDR25J-60K8)-WM-E-042004
ALL MEMORY USED UP
M
RADIO OPERATION
1.Slide the CD/RADIO FUNCTION switch (on
the bottom of the set) toRADIO position.
2.Press the AM/FM BAND button to select the
desired wave band.
3.Tune to desired station by pressing the
SKIP/TUNING buttons. Each time the
button is pressed, the frequency changes.
4.To search for a station quickly (automatic tuning), keep the SKIP/TUNING
buttons pressed until the frequency starts to change rapidly. After tuning into a
strong station, the search stops.
5.If you tune into an FM stereo station, “ FM STEREO ” will show in the display.
6.Adjust the VOLUME control to your listening preference.
7.If you prefer more bass, slide the BASS BOOST switch to ON position.
8.To turn off the radio, slide the CD/RADIO FUNCTION switch to CD position.
TUNING UP &
DOWN BUTTONS
AM/FM BAND
BUTTON
VOLUME
CONTROL
Presetting Stations
UP TO 5 AM AND 5 FM STATIONS CAN BE STORED INTO THE PRESET MEMORIES.
(THEY WILL REMAIN IN MEMORY AS LONG AS THE BATTERIES ARE INSTALLED, OR
AC POWER CORD IS CONNECTED.)
1.Slide the CD/RADIO FUNCTION switch to RADIO position.
2.
Press the AM/FM BAND button to select AM or FM band, and
pressthe SKIP/TUNING buttons to select a station.
3.Press the radio MEMORY button, “
4.While the “
buttons repeatedly to select one of 5 memory locations
(1-5) you want to store, press MEMORY button to confirm.
NOTE: Steps 3-4 should be done quickly.
5.Repeat the above steps 2 to 4 to store other 4 stations into memory.
6.Each memory location can store 2 stations, one for AM, the other for FM.
NOTE: Before you disconnect the power (AC and Battery) of the set, make sure
M
” is blinking, press one of the radio PRESET
the CD/RADIO FUNCTION switch is at the CD position, then you have
approximately 30 seconds to re-connect the power. Otherwise, the memories
may be lost and need to be re-programmed.
Listening to Preset Stations
1.Slide the CD/RADIO FUNCTION switch to RADIO position.
2.Press the AM/FM BAND button to select the band you want (AM or FM).
3.Press the PRESET buttons to select the stations stored. You will receive the station
you stored into that preset memory location.
4.To shut off the radio, slide the CD/RADIO FUNCTION switch to CD position.
” will flash in the display..
(after you programmed them)
9
IB-CD915(CDR25J-60K8)-WM-E-042004
MAINTENANCE
Cleaning the lens
A dirty lens will cause sound skipping. If
the lens is very dirty, the player may not
work. We suggest using a special cleaning
disk (not included) available in most music
and Hi-Fi stores. However, if you do not
have one, you may use a cotton swab
very slightly dampened with alcohol to
clean the lens.
Cleaning the cabinet
Wipe with a soft cloth. If the cabinet is
very dirty, dampen (not dripping wet) the
cloth with a weak solution of soapy water,
and then wipe clean.
Handling Compact Discs
Dirty, scratched or warped discs may
•
causeskipping or noise.
Handle the disc only by the edges. To
•
keep clean, do not touch its surface.
Discs should be stored in their cases
•
after use to avoid scratches.
Do not expose discs to direct sunlight,
•
high humidity, high temperatures, or
dust, etc. Prolonged exposure to
extreme temperatures can warp the disc
(such as leaving the discs in your car
during summertime).
Do not stick or write anything on either
•
side of disc. Sharp writing instruments, or
the inks used in some felt-tip pens, may
damage its surface.
Cleaning the Discs
Fingerprints should be carefully wiped
•
from the surface of disc with a soft cloth.
Unlike conventional records, compact
discs have no grooves to collect dust
and microscopic dirt, so gently wiping
them with a soft cloth should remove
most particles. Wipe in a straight
motion from the center to the edge.
Never use thinner, benzine, record
•
cleaner or antistatic spray on a compact
disc. Such chemicals can damage its
plastic surface.
To remove the Disc
Open the CD DOOR by sliding the DOOR
OPEN button, hold the disc by the edge
while slightly pressing on the center
spindle as illustrated, then lift it from the
edge to release and remove.
NOTE:
Always press the STOP button and wait
for the disc to stop rotating before sliding
the DOOR OPEN button to remove the
disc.
10
IB-CD915(CDR25J-60K8)-WM-E-042004
SAFETY PRECAUTIONS
Do not take the set apart. The laser beam used in the set may harm your eyes. Refer
servicing to qualified service personnel only.
Do not insert pins or coins, clips, or any objects inside the set.
This set is equipped with a safety device which automatically turns the laser beam off
when the disc door is opened.
Do not drop the set or subject it to strong shocks. Doing so could result in damage.
Do not place the set in locations where the temperature is high, or in humid or dusty
locations, or locations with long heavy vibrations, or tilted surfaces.
The set’s cabinet may warp or the set may be damaged if it is placed in direct sunlight,
near heaters (where the temperature is 1400F/600C or higher) or in cars with the
windows closed. In the summer, the temperature may get as high as 2120F/1000C or
more.
Use the set within a temperature range of 410F/50C to 950F/350C.
Use ONLY the DC 4.5V 700mA AC ADAPTOR with polarity , others may damage
your set. Disconnect the ADAPTOR from the wall outlet when the set is not to be used
for an extended period of time (3 days or more).
When cleaning your set, use a soft dry cloth. Do not use solvents or commercially
available cleaners, as they may damage or discolor the finish.
Do not wear headphones while operating a motor vehicle. This could create a traffic
hazard and is illegal in many areas. Do not use this set when bicycling or running.
The headphones supplied with your set provide superb stereo listening while allowing
you to hear some outside sounds when listening at normally low volume levels. Listening
at extremely high volume levels minimizes the intrusion of outside noise/sounds. In the
interest of safety, it is strongly advised against the use while engaging in activities
where the exclusion of external sounds (whistles, horns, sirens, traffic, etc.). Also loud
volume can hurt your ears. If you notice that the sound has become weak or distorted
or if tracks do not change, this is an indication that your batteries are weak. Replace
both batteries at the same time (see Using With Batteries).
Your CD-915 is identified by a serial number located in the BATTERY COMPARTMENT.
Record this number in the space provided below.
Model CD-915Serial No. Date Purchased:
This manual contains detailed information on its safety and use. Please read it carefully
so that you may take full advantage of its many features, and ensure a safe reliable
operation. Keep this manual for future reference.
CONDENSATION
If cold water is poured into a glass, water droplets form on the outside of the glass.
This is called condensation. Condensation may occur on internal operating parts of the
lens.
Condensation occurs:
When the set is brought from the cold outdoors into a warm room, or from a cold room
to a heated one, or in the summer, if the set is moved from an air-conditioned room or
car to a hot or humid location.
Should condensation occur, the set may not operate properly. Open the CD DOOR
and wait for about 20 minutes (to allow the internal parts to adjust to the surrounding
temperature) before using the set.
11
IB-CD915(CDR25J-60K8)-WM-E-042004
IMPORTANT REQUIREMENT BY THE FCC
Since the CD circuitry may cause interference to other radios nearby, switch this
set off when not in use or move it away from the affected radios.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesirable operation.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
SAFETY CERTIFICATION
This Compact Disc Player is made and tested to meet safety standards of the FCC
requirements and compliance with safety performance of the U.S. Department of Health
and Human Services, and also with FDA Radiation Performance Standards 21 CFR
Subchapter J.
WARNING
To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
•
LASER SAFETY
THIS SET EMPLOYS AN OPTICAL LASER BEAM SYSTEM IN THE CD MECHANISM,
DESIGNED WITH BUILT-IN SAFEGUARDS. DO NOT ATTEMPT TO DISASSEMBLE.
EXPOSURE TO THIS INVISIBLE LASER LIGHT BEAM MAY BE HARMFUL TO HUMAN
EYES. THIS IS A CLASS-1 LASER PRODUCT. USE OF ADJUSTMENTS OTHER THAN
THOSE SPECIFIED HEREIN, MAY RESULT IN HAZARDOUS LASER LIGHT BEAM
EXPOSURE. THIS COMPACT DISC PLAYER SHOULD NOT BE ADJUSTED OR
REPAIRED BY ANYONE EXCEPT QUALIFIED SERVICE PERSONNEL. THE LASER
MECHANISM IN THE SET CORRESPONDS TO THE STYLUS (NEEDLE) OF A RECORD
PLAYER. ALTHOUGH THIS PRODUCT USES A LASER PICK-UP LENS, IT IS
COMPLETELY SAFE WHEN OPERATED ACCORDING TO DIRECTIONS.
12
IB-CD915(CDR25J-60K8)-WM-E-042004
TROUBLE SHOOTING GUIDE
Symptoms
Tracks do not
change or set
does not play
normally.
CD Player will not
turn on.
Disc will not play.
No sound from
headphones.
VOLUME control
has no function.
Sound is skipping
or sound stops.
Sound is distorted.
Buttons do not
work.
Radio does not
work.
FM reception is
weak.
AM reception is
weak.
Causes
Batteries are weak (they
may test OK on tester but
they are weak for CD
operation).
Dead or weak batteries.
The optional AC ADAPTOR
not connected properly.
Disc inserted incorrectly.
Defective compact disc.
CD DOOR not closed.
Moisture has formed inside
the CD deck.
Headphone plug not
inserted properly.
VOLUME control set to
minimum.
Weak batteries.
Defective compact disc. Try another compact disc.
Headphones plugged into
LINE OUT Jack.
The compact disc or lens
is dirty or CD is scratched.
Music is too loud.
BASS BOOST is ON.
Weak batteries.
Electronic or static error
caused circuitry to lock.
FUNCTION switch is in the
CD position.
The FM Antenna is built-into
your headphone wire.
The built-in AM Antenna is
directional.
Replace both batteries with fresh
alkaline batteries. Battery life with
fresh batteries is above 8 hours for
continuous CD play and 5 hours longer
for radio use (rechargeable batteries
have 1/2 of that life).
Replace both batteries with fresh
ones.
Check AC ADAPTOR connection at
AC outlet and the rear of the set.
Re-insert disc with label side facing
up.
Try another compact disc.
Close the door securely.
Take out the CD and leave the CD
Door open for about 20 minutes to
dry the moisture condensation.
Re-insert headphone plug into
PHONES jack (not LINE OUT).
Increase the volume.
Replace with fresh batteries or use
an optional AC ADAPTOR.
Plug headphones into PHONES
jack. (NOT THE LINE OUT JACK)
Clean or replace the compact disc
or clean the lens.
Lower the VOLUME control.
Slide BASS BOOST switch to OFF.
Replace both batteries or use an
optional AC ADAPTOR.
Remove batteries and ADAPTOR.
Wait 15 seconds and re-insert. Make
sure batteries are fresh or the
optional ADAPTOR has power.
Slide the FUNCTION switch to the
RADIO position.
Straighten your headphone wire, or
bring your set closer to a window.
Rotate the set or bring the set near a
window.
13
Solutions
IB-CD915(CDR25J-60K8)-WM-E-042004
TECHNICAL SPECIFICATIONS
CD Player Section
Frequency response ..............................
Sampling frequency ................................
D/A converter .........................................
Error correction method ..........................
Pickup ...................................................
Laser diode material GaAIAs
Laser output less than 44.6mW
NOTE: This CD player will only play NORMAL music CDs (or CD-R CDs).
This set will not play CD-RW encoded discs.
50Hz-15kHz +1/-2dB
44.1kHz
1-bit
CIRC
Optical 3-beam semiconductor laser
(780nm wavelength)
Radio Section
Frequency Range .................................
AM: 530 - 1700 kHz
FM: 88 - 108 MHz
General
Maximum output (stereo headphones) .....
Power Supply
AC adaptor ...........................................
DC .......................................................
Set Dimensions (approximate)
Width ...............................................
Depth ..............................................
Height ..............................................
Weight (approximate) ...........................
Because the products are subject to continuous improvement, LENOXX reserves the
right to modify product designs and specifications without notice and without incurring any
obligation.
20mW + 20mW
120V/60Hz (not included)
3V: Using 2 size “AA” batteries
5 3/4"
5 3/4"
1 1/4"
9.5oz. (270g) (set only)
14
IB-CD915(CDR25J-60K8)-WM-E-042004
LIMITED WARRANTY
We warrant this product to be free from defects in material and workmanship under
normal use for a period of 90 days after purchase and we will repair it free of charge or
replace it at no charge, should it become defective under this warranty, providing you
submit proof of purchase (sales slip) with the set.
During the initial 90 day period after original purchase, we will service or exchange, at no
charge, the set that is returned to LENOXX ELECTRONICS CORP. After the initial 90 day
period expires, and for a period of 12 months from original purchase, we will repair the unit
covering any part(s) that need to be replaced at no charge, but will charge for the cost of
labor, return postage paid by Lenoxx.
This warranty does not apply to any products which have been subject to misuse,
neglect or accident. This warranty does not cover broken headphones or cabinet.
UNDER NO CIRCUMSTANCES WILL LENOXX ELECTRONICS CORP. BE LIABLE FOR
ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitations
or exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state. The following charges apply to repairs beyond the
warranty period: $15.00. Be sure to pack carefully and return postage paid insured
together with your money order (personal checks will not be accepted) and sales receipt to:
LENOXX ELECTRONICS CORP., 2 GERMAK DRIVE, CARTERET N.J. 07008
For customer service
Dial 1-800-315-5885 (MONDAY - THURSDAY 9:00 AM - 5:00 PM, FRIDAY 9:00 AM - 1:00 PM EST)
or Visit Our Website: http://www.lenoxx.com
© 2004 LENOXX ELECTRONICS CORP.
2 GERMAK DRIVE
CARTERET, N.J. 07008
MADE & PRINTED IN CHINA
15
IB-CD915(CDR25J-60K8)-WM-E-042004
Loading...