U.S. GOVERNMENT USERS – RESTRICTED RIGHTS: Our products and/or services are provided with
RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to the GSA ADP Schedule
contract with Lenovo, if any, or the standard terms of this commercial license, or if the agency is unable to accept
this Program under these terms, then we provide this Program under the provisions set forth in Commercial
Computer Software–Restricted Rights at FAR 52.227-19, when applicable, or under Rights in Data-General, FAR
52.227.14 (Alternate III).
Explanation of Hard Disk Capacity
Dear user,
While using your computer, you may discover that the nominal hard
disk capacity indicated is somewhat different from the disk capacity
displayed by the operating system. For example, a nominal 40GB hard
disk will appear as less than 40GB in the operating system. This
discrepancy is not an error in hard disk installation nor any other
problem, but a normal phenomenon of computers. This phenomenon is
primarily due to the following reasons:
I. Different standards used by the manufacturer and operating
system when calculating hard disk capacity
Hard disk manufacturers use a radix of 1000, i.e. 1G = 1,000MB, 1MB =
1,000KB, 1KB = 1,000 bytes. However, when identifying hard disk capacity,
operating systems use a radix of 1024, i.e. 1GB = 1,024MB, 1MB = 1,024KB,
1KB = 1,024 bytes. The standard adopted by your computer is that of the
hard disk manufacturers. Since the standards adopted by the hard disk
manufacturer and operating system are different, the hard disk capacity
displayed by the operating system will be different from the nominal hard
disk capacity.
For example, if the hard disk is nominally X G, even when it is completely
empty, the capacity displayed by the operating system will be:
X × 1000 × 1000 × 1000/ (1024 × 1024 × 1024) ≈ X × 0.931 G
If a portion of the hard disk space has been used for some specific purpose,
then the capacity indicated by the operating system will be even less than
X × 0.931 G.
II. A portion of the hard disk space is used for specific purposes
Lenovo computers come with preinstalled OneKey Recovery software, so
the hard disk has a special portion partitioned before delivery, which is
used to store hard disk mirror and OneKey Recovery program files. The
size of the reserved space for this partition varies according to the model,
operating system and software of the computer. For the sake of safety, this
partition is not evident, which is commonly referred to as a “hidden
partition”. It is invisible in the operating system and this portion of disk
space is not included when displaying hard disk capacity.
In addition, after the hard disk is partitioned or formatted, the system will
assign a certain amount of hard disk space for the system files.
For the above reasons, the available hard disk space indicated by the
operating system is always less than the computer’s nominal hard disk
capacity.
When your computer is turned on or the battery is
charging, the base, the palm rest, and some other
parts may become hot. Avoid keeping your hands,
your lap, or any other part of your body in contact
with a hot section of the computer for any
extended length of time. When you use the
keyboard, avoid keeping your palms on the palm
rest for a prolonged period of time.
Your computer generates some heat during
normal operation. The amount of heat depends on
the amount of system activity and the battery
charge level. Extended contact with your body,
even through clothing, could cause discomfort or
even a skin burn. Periodically take breaks from
using the keyboard by lifting your hands from the
palm rest; and be careful not to use the keyboard
for any extended length of time.
iii
Read This First
When the AC adapter of your computer is
connected to an electrical outlet, it generates heat.
Do not place the adapter in contact with any part
of your body while using it. Never use the AC
adapter to warm your body. Extended contact
with your body, even through clothing, may cause
a skin burn.
Route the cables of an AC adapter, a mouse, a
keyboard, a printer, or any other electronic device,
or communication lines, so that they cannot be
walked on, tripped over, pinched by your
computer or other objects, or in any way subjected
to treatment that could disturb the operation of
your computer. Applying strong force to the
cables may damage or break them.
iv
Read This First
Before moving your computer, do one of the
following: turn it off or press Fn + F1 to put it in
sleep mode.
Before moving the computer, make sure that the
power on indicator is off. This will help to prevent
damage to the hard disk drive, and possible loss of
data.
Do not drop, bump, scratch, twist, hit, vibrate, or
push your computer, display, or external devices.
v
Read This First
Do not distort, bend or extrude your liquid crystal
display.
Do not place heavy objects on your computer or
display.
vi
Read This First
Place liquids away from your computer to avoid
spills, and keep your computer away from water
to avoid the danger of electrical shock.
Use a quality carrying case that provides adequate
cushion and protection. Do not pack your
computer in a tightly packed suitcase or bag.
The spring-loaded battery latch keeps the battery pack secured in
place. When you insert a battery pack, this latch automatically secures
the battery in place. To remove the battery, hold this latch in the
unlocked position.
Battery latch - manual
The manual battery latch is used to keep the battery pack secured.
Move the manual battery latch to the unlocked position to insert or
remove the battery pack. Move the manual latch to the locked position
after inserting the battery pack.
Memory (RAM) compartment
The memory compartment provides expansion capabilities for
additional memory. The BIOS automatically detects the amount of
memory in the system and configures CMOS accordingly during the
Power-On Self-Test (POST) process. There is no hardware or software
(including BIOS) setup required after the memory is installed.
Note:
Only purchase expansion modules from authorized retailers of this
computer to ensure maximum compatibility and reliability.
When you finish working with your computer, you can put it to sleep or
shut it down.
Putting your computer to Sleep
If you will be away from your computer for only a short time, put the
computer to sleep.
When the computer is in sleep, you can quickly wake it and bypass the
startup process.
To put the computer to sleep, do one of the following.
Click Start and select Sleep from the Start menu.
Press Fn+ F1.
Warning:
Wait until the power indicator light starts blinking (indicating that the
computer is in sleep) before you move your computer. Moving your
computer while the hard disk is spinning can damage the hard disk,
causing loss of data.
To wake the computer, do one of the following.
Press the power button.
Press any key.
10
Chapter 2. Using Your Computer
Shutting Down Your computer
If you are not going to use your computer for a day or two, shut it down.
To shut down your computer, click Start and select Shut down from the
Start menu.
After you begin working with your computer, you might need to adjust
your display to achieve its optimum performance.
Adjusting the brightness
You can increase or decrease the brightness on your display.
To adjust the brightness on your display, press Fn + up/down arrow.
Switching between wide screen and normal screen
You can change the aspect ratio on your display.
To switch between wide screen and normal mode, press Fn + F4 to open
Resolution switchover screen.
Select “1366 × 768” or “1024 × 768” to switch wide screen and normal screen.
Note:
You can also select provided resolution from the pull down menu.
Your computer has a numeric keypad and function keys incorporated in
the standard keyboard.
Numeric Keypad
The keyboard has keys that, when enabled, work as a 10-key numeric
keypad.
To enable or disable the numeric keypad, press Fn+Insert/NmLk.
* The illustrations in this manual may differ from the actual product.
13
Chapter 2. Using Your Computer
Function Key Combinations
Through the use of the function keys, you can change operational features
instantly. To use this function, press and hold the Fn key ; then press one
of the function keys .
%
$
14
Chapter 2. Using Your Computer
The following describes the features of each function key.
Fn +Esc: Turn on/off the integrated camera.
Fn +F1: Put your computer in sleep mode.
Fn +F2: Turn off the LCD screen (any subsequent operation will turn the
LCD screen back on).
Fn +F3: Shift to other connected display devices.
Fn +F4: Switch between wide screen and normal mode.
Fn +F5: Enable/disable the built-in wireless device feature.
Fn +F6: Enable/disable the touch pad.
Fn +F7: Play/pause Media Player playback.
Fn +F8: Stop Media Player playback.
Fn +F9: Skip to the previous track.
Fn +F10: Skip to the next track.
Fn +F11: F12 function.
Fn +Insert/NmLk: Enable/disable the Numeric keypad.
Fn +Delete/ScrLk: Enable/disable Scroll Lock.
Fn +P
rtSc/SysRq: System request.
Fn +Pause/Break: Pause to view the system information during start-up.
Fn +up/down arrow: Increase/decrease display brightness.
Fn +right/left arrow: Increase/decrease computer volume.
Your computer has several special keys and buttons.
Touch inductive panel
To display the buttons, press the Mute or Volume key.
Open Dolby function setup screen.
Open user define utility.
Open user define utility.
Mute / unmute the sound.
Change volume.
16
Chapter 2. Using Your Computer
Novo button
The Novo button functions as OneKey Recovery key; use with caution.
Press the Novo button to enter the main interface of OneKey Recovery
while the power is off.
Attention:
When you press NOVO key to turn on the computer, please ensure that
your computer is not connected with other peripherals (such as USB
storage device, etc.), otherwise the system may not operate properly.
Once done, the system can no longer return to its previous state. All data
on the primary hard disk partition (usually drive C) will subsequently be
lost. Make sure all important files on the primary hard disk partition have
been backed up onto another hard disk or USB hard disk drive before this
operation.
For details, see OneKey Recovery User Guide.
Note:
When your computer is running Windows Vista
EnergyCut program installed, you can shift the power schemes by pressing
the Novo button.