How it Works
Lenovo
Loading...
K220
User Manual
37 pgs3.14 Mb0
User Manual
64 pgs1.19 Mb0

Lenovo K220 User Manual

Download
Page 1
Contents
Chapter 1. About this manual ................................................ 1
Chapter 2. Safety information ................................................ 4
Contents
Important Safety Information ......................................................................1
Using eSupport ....................................................................................................2
Important information about replacing RoHS compliant FRUs ..2
General safety ....................................................................................................... 4
Electrical safety .................................................................................................... 5
Safety inspection guide ................................................................................... 7
Handling electrostatic discharge-sensitive devices .........................8
Grounding requirements ...............................................................................8
Safety notices ........................................................................................................9
Chapter 3. General information ...........................................12
Specifications ..................................................................................................... 12
Chapter 4. General Checkout ...............................................13
Problem determination tips ...................................................................... 14
Chapter 5. Using the Setup Utility (Type G33) .................16
Starting the Setup Utility program ......................................................... 16
Viewing and changing settings ................................................................ 16
Using passwords .............................................................................................. 17
Using Device ...................................................................................................... 20
Selecting a startup device ........................................................................... 20
i
Page 2
Hardware Maintenance Manual
ii
Exiting from the Setup Utility program ................................................ 21
Chapter 6. Using the Setup Utility (Type G43) .................22
Starting the Setup Utility program ......................................................... 22
Viewing and changing settings ................................................................ 22
Using passwords .............................................................................................. 23
Using Device ...................................................................................................... 25
Selecting a startup device ........................................................................... 26
Exiting from the Setup Utility program ................................................ 27
Chapter 7. Using the Setup Utility (Type G31) .................28
Starting the Setup Utility program ......................................................... 28
Viewing and changing settings ................................................................ 28
Using passwords .............................................................................................. 29
Using Device ...................................................................................................... 31
Selecting a startup device ........................................................................... 32
Exiting from the Setup Utility program ................................................ 33
Chapter 8. Symptom-to-FRU Index.....................................34
Hard disk drive boot error ........................................................................... 34
Power Supply Problems ................................................................................ 35
Beep symptoms ............................................................................................... 36
POST error codes ............................................................................................. 37
Undetermined problems ............................................................................. 39
Chapter 9. Replacing hardware ...........................................40
Removing the computer cover ................................................................ 40
Removing and replacing the front bezel ............................................. 42
Page 3
Contents
iii
Replacing the power supply ..................................................................... 43
Replacing the heat sink assembly .......................................................... 44
Replacing a memory module ................................................................... 45
Replacing an adapter .................................................................................... 46
Note: Replacement of some models equipped with graphic adapter
Replacing the hard disk drive ................................................................... 49
Replacing an optical drive .......................................................................... 50
Replacing the system fan assembly ....................................................... 52
Replacing the keyboard .............................................................................. 53
Replacing the mouse .................................................................................... 54
Replacing the External speaker ............................................................... 55
Completing the installation ....................................................................... 55
Chapter 10. Additional Service Information
(Type G33) .................................................................................57
Power management ...................................................................................... 57
Chapter 11. Additional Service Information
(Type G43) ................................................................................58
Power management ...................................................................................... 58
Chapter 12. Additional Service Information
(Type G31) .................................................................................59
Power management ...................................................................................... 59
Appendix. Statement .............................................................60
Page 4
About this manual
This manual contains service and reference information for Lenovo IdeaCentre K computers listed on the cover. It is intended only for trained servicers who are familiar with Lenovo computer products.
Before servicing a Lenovo product, be sure to read the Safety Information.
This manual includes a complete FRU part number listing for each machine type and model listed on the cover. If you have internet access, FRU part numbers are also available at: http:/www.lenovo.com/support.
Chapter 1. About this manual
1
The description of the TV card in this manual is only used for the machines which have the TV card. It is invalid for those machines which do not have TV card.
Important Safety Information
Be sure to read all caution and danger statements in this book before performing any of the instructions.
Veuillez lire toutes les consignes de type DANGER et ATTENTION du présent document avant d’exécuter les instructions.
Lesen Sie unbedingt alle Hinweise vom Typ “ACHTUNG” oder “VORSICHT” in dieser Dokumentation, bevor Sie irgendwelche Vorgänge durchführen
Leggere le istruzioni introdotte da ATTENZIONE e PERICOLO presenti nel manuale prima di eseguire una qualsiasi delle istruzioni
Certifique-se de ler todas as instruções de cuidado e perigo neste manual antes de executar qualquer uma das instruções
Es importante que lea todas las declaraciones de precaución y de peligro de este manual antes de seguir las instrucciones.
执行任何说明之前，请确保已阅读本书中的所有警告和危险声明。
1
Page 5
Hardware Maintenance Manual
2
Using eSupport
For Key Commodities (Examples - hard disk drive, system board, microprocessor, LCD, and memory)
eSupport can be used to view the list of key commodities built in a • particular machine serial. eSupport can be accessed at the following Web site: • http://www.lenovo.com/support To view the key commodities:•
1. Click Parts information.
2. Under Parts information, click Parts lookup.
3. Under Parts lookup, type the model type and serial number; then
For the remaining FRUs (the complete list of FRUs at the MT Model level)
eSupport can be used to view the complete list of FRUs for a machine • type and model. To view the complete list of FRUs for a machine type:•
1. Point your browser to http://www.lenovo.com/support.
2. Type the machine type (Example: 8129) in the Use Quick Path field;
3. Under Browse by product, click Continue.
4. Under Important information, click Parts information.
5. In the Refine results field, select Service parts; then click the entry for
click Continue. The key commodities are returned in the eSupport record under Parts shipped with your system.
then click Go.
your machine type. The list of service parts by description, with applicable machine type model and FRU part number is displayed.
Important information about replacing RoHS compliant FRUs
RoHS, The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive (2002/95/EC) is a European Union legal requirement affecting the global electronics industry. RoHS requirements must be implemented on Lenovo products placed on the market after June 2006. Products on the market before June 2006 are not required to have RoHS compliant parts.
So, if the parts are not compliant originally, replacement parts can also be noncompliant, but in all cases, if the parts are compliant, the replacement parts must also be compliant.
Lenovo plans to transition to RoHS compliance well before the
Page 6
Chapter 1. About this manual
3
implementation date and expects its suppliers to be ready to support Lenovo’s requirements and schedule. Products sold in 2005, will contain some RoHS compliant FRUs. The following statement pertains to these products and any product Lenovo produces containing RoHS compliant parts.
RoHS compliant Lenovo IdeaCentre K parts have unique FRU part numbers. Before or after June, 2006, failed RoHS compliant parts must always be replaced using RoHS compliant FRUs, so only the FRUs identified as compliant in the system HMM or direct substitutions for those FRUs can be used.
Products marketed before June 2006 Products marketed after June 2006 Current or original part
Non-RoHS Can be Non-RoHS Must be RoHS Must be RoHS Non-RoHS Can be RoHS Non-RoHS Can sub to RoHS RoHS Must be RoHS
Replacement FRU
Current or original part
Replacement FRU
Note: A direct substitution is a part with a different FRU part number that
is automatically shipped by the distribution center at the time of order.
Related Web URLs are:
Lenovo information for Suppliers website: • http://www-03.ibm.com/procurement/proweb.nsf/ ContentDocsByTitle/United+States~Information+for+suppliers RoHS Directive: • http://europa.eu.int/eur-lex/pri/en/oj/dat/2003/l_037/ l_03720030213en00190023.pdf California Senate Bills 20, 50: • http://www.ciwmb.ca.gov/HHW/Events/AnnualConf/2004/ presentation/MPaparian.pdf
Page 7
Hardware Maintenance Manual
4
Safety information
This chapter contains the safety information that you need to be familiar with before servicing a computer.
General safety
Follow these rules to ensure general safety:
Observe good housekeeping in the area of the machines during and • after maintenance. When lifting any heavy object: •
1. Ensure you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift.
4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the muscles in your back. Do not attempt to
lift any objects that weigh more than 16 kg (35 lb) or objects that you think are too heavy for you.
Do not perform any action that causes hazards to the customer, or that • makes the equipment unsafe. Before you start the machine, ensure that other service representatives • and the customer’s personnel are not in a hazardous position. Place removed covers and other parts in a safe place, away from all • personnel, while you are servicing the machine. Keep your tool case away from walk areas so that other people will not • trip over it. Do not wear loose clothing that can be trapped in the moving parts of a • machine. Ensure that your sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it. Insert the ends of your necktie or scarf inside clothing or fasten it with • a nonconductive clip, approximately 8 centimeters (3 inches) from the end. Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners • for your clothing. Remember: Metal objects are good electrical conductors.
2
Page 8
Chapter 2. Safety information
5
Wear safety glasses when you are: hammering, drilling soldering, • cutting wire, attaching springs, using solvents, or working in any other conditions that might be hazardous to your eyes. After service, reinstall all safety shields, guards, labels, and ground wires. • Replace any safety device that is worn or defective. Reinstall all covers correctly before returning the machine to the • customer.
Electrical safety
CAUTION: Electrical current from power, telephone, and communication cables can be hazardous. To avoid personal injury or equipment damage, disconnect the attached power cords, telecommunication systems, networks, and modems before you open the server/workstation covers, unless instructed otherwise in the installation and configuration procedures.
Observe the following rules when working on electrical equipment.
Important: Use only approved tools and test equipment. Some hand
tools have handles covered with a soft material that does not insulate you when working with live electrical currents.
Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock.
Find the room emergency power-off (EPO) switch, disconnecting • switch, or electrical outlet. If an electrical accident occurs, you can then operate the switch or unplug the power cord quickly. Do not work alone under hazardous conditions or near equipment that • has hazardous voltages. Disconnect all power before: • – Performing a mechanical inspection – Working near power supplies – Removing or installing main units Before you start to work on the machine, unplug the power cord. If • you cannot unplug it, ask the customer to power-off the wall box that supplies power to the machine and to lock the wall box in the off position.
Page 9
Hardware Maintenance Manual
6
If you need to work on a machine that has exposed electrical circuits, • observe the following precautions: – Ensure that another person, familiar with the power-off controls, is
– Use only one hand when working with powered-on electrical
– When using testers, set the controls correctly and use the approved
– Stand on suitable rubber mats (obtained locally, if necessary) to
Regularly inspect and maintain your electrical hand tools for safe • operational condition. Do not use worn or broken tools and testers. • Never assume• that power has been disconnected from a circuit. First, check that it has been powered-off. Always look carefully for possible hazards in your work area. Examples • of these hazards are moist floors, nongrounded power extension cables, power surges, and missing safety grounds. Do not touch live electrical circuits with the reflective surface of a • plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage. Do not service the following parts with the power on when they are • removed from their normal operating places in a machine: – Power supply units – Pumps – Blowers and fans – Motor generators and similar units. (This practice ensures correct grounding of the units.) If an electrical accident occurs:• – Use caution; do not become a victim yourself. – Switch off power. – Send another person to get medical aid.
near you. Remember: Another person must be there to switch off the power, if necessary.
equipment; keep the other hand in your pocket or behind your back. Remember: There must be a complete circuit to cause electrical shock. By observing the above rule, you may prevent a current from passing through your body.
probe leads and accessories for that tester.
insulate you from grounds such as metal floor strips and machine frames. Observe the special safety precautions when you work with very high voltages; these instructions are in the safety sections of maintenance information. Use extreme care when measuring high voltages.
Page 10
Chapter 2. Safety information
7
Safety inspection guide
The intent of this inspection guide is to assist you in identifying potentially unsafe conditions on these products. Each machine, as it was designed and built, had required safety items installed to protect users and service personnel from injury. This guide addresses only those items. However, good judgment should be used to identify potential safety hazards due to attachment of features or options not covered by this inspection guide.
If any unsafe conditions are present, you must determine how serious the apparent hazard could be and whether you can continue without first correcting the problem.
Consider these conditions and the safety hazards they present:
Electrical hazards, especially primary power (primary voltage on the • frame can cause serious or fatal electrical shock). Explosive hazards, such as a damaged CRT face or bulging capacitor • Mechanical hazards, such as loose or missing hardware •
The guide consists of a series of steps presented in a checklist. Begin the checks with the power off, and the power cord disconnected.
Checklist:
1. Check exterior covers for damage (loose, broken, or sharp edges).
2. Power-off the computer. Disconnect the power cord.
3. Check the power cord for: a. A third-wire ground connector in good condition. Use a meter to
measure third-wire ground continuity for 0.1 ohm or less between the external ground pin and frame ground.
b. The power cord should be the appropriate type as specified in the
parts listings.
c. Insulation must not be frayed or worn.
4. Remove the cover.
5. Check for any obvious alterations. Use good judgment as to the safety of any alterations.
6. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage.
7. Check for worn, frayed, or pinched cables.
8. Check that the power-supply cover fasteners (screws or rivets) have not been removed or tampered with.
Page 11
Hardware Maintenance Manual
8
Handling electrostatic discharge-sensitive devices
Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge.
Notes:
1. Use product-specific ESD procedures when they exceed the requirements noted here.
2. Make sure that the ESD protective devices you use have been certified (ISO 9000) as fully effective.
When handling ESD-sensitive parts:
Keep the parts in protective packages until they are inserted into the • product. Avoid contact with other people. • Wear a grounded wrist strap against your skin to eliminate static on • your body. Prevent the part from touching your clothing. Most clothing is insulative • and retains a charge even when you are wearing a wrist strap. Use the black side of a grounded work mat to provide a static-free • work surface. The mat is especially useful when handling ESD-sensitive devices. Select a grounding system, such as those listed below, to provide • protection that meets the specific service requirement.
Note: The use of a grounding system is desirable but not required to
protect against ESD damage.
– Attach the ESD ground clip to any frame ground, ground braid, or
green-wire ground.
– Use an ESD common ground or reference point when working on a
double-insulated or battery-operated system. You can use coax or connector-outside shells on these systems.
– Use the round ground-prong of the ac plug on ac-operated
computers.
Grounding requirements
Electrical grounding of the computer is required for operator safety and correct system function. Proper grounding of the electrical outlet can be verified by a certified electrician.
Page 12
Chapter 2. Safety information
9
Safety notices
The caution and danger safety notices in this section are provided in the the language of English.
DANGER Electrical current from power, telephone and communication cables is hazardous.
To avoid a shock hazard:
Do not connect or disconnect any cables or perform installation, • maintenance, or reconfiguration of this product during an electrical storm. Connect all power cords to a properly wired and grounded electrical • outlet. Connect to properly wired outlets any equipment that will be • attached to this product. When possible, use one hand only to connect or disconnect signal • cables. Never turn on any equipment when there is evidence of fire, water, or • structural damage. Disconnect the attached power cords, telecommunications systems, • networks, and modems before you open the device covers, unless instructed otherwise in the installation and configuration procedures. Connect and disconnect cables as described in the following table • when installing, moving, or opening covers on this product or attached devices.
To Connect To Disconnect
1. Turn everything OFF.
2. First, attach all cables to devices.
3. Attach signal cables to connectors.
4. Attach power cords to outlet.
5. Turn device ON.
1. Turn everything OFF.
2. First, remove power cords from outlet.
3. Remove signal cables from connectors.
4. Remove all cables from devices.
Page 13
Hardware Maintenance Manual
10
CAUTION: When replacing the lithium battery, use only Part Number 33F8354 or an equivalent type battery recommended by the manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of.
Do not:
Throw or immerse into water • Heat to more than 100°C (212°F)• Repair or disassemble•
Dispose of the battery as required by local ordinances or regulations.
CAUTION: When laser products (such as CD-ROMs, DVD-ROM drives, fiber optic devices, or transmitters) are installed, note the following:
Do not remove the covers. Removing the covers of the laser product • could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device. Use of controls or adjustments or performance of procedures other • than those specified herein might result in hazardous radiation exposure.
DANGER: Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following: Laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam.
Page 14
Chapter 2. Safety information
11
1
2
CAUTION: Use safe practices when lifting.
CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source.
CAUTION: Do not place any object weighing more than 82 kg (180 lbs.) on top of rack-mounted devices.
Page 15
Hardware Maintenance Manual
General information
This chapter provides general information that applies to all machine types supported by this publication.
Specifications
This section lists the physical specifications for your computer.
3
Type Lenovo IdeaCentre K
This section lists the physical specifications.
Dimensions
Width: 180 mm Height: 388 mm Length: 436.5 mm
Environment
Air temperature:
Operating: 10° to 35°C Transit: -40° to 55°C
Humidity:
Operating: 35% to 80% Transit: 20% to 93% (40°C) Altitude: 86KPa to 106KPa
Electrical input
Input voltage: 220V±22V Input frequency: 50Hz ±1Hz
12
Page 16
General Checkout
The drives in the computer you are servicing might have been rearranged or the drive startup sequence changed. Be extremely careful during write operations such as copying, saving, or formatting. Data or programs can be overwritten if you select an incorrect drive.
Attention
Chapter 4. General Checkout
4
General error messages appear if a problem or conflict is found by an application program, the operating system, or both. For an explanation of these messages, refer to the information supplied with that software package.
Notes
• Thedefaultisforthiscomputertobootupinquietmode(nobeep,
no memory count and checkpoint code display) when no errors are detected by POST.
• Toenablebeep,memorycount,andcheckpointcodedisplaywhen
a successful POST occurs, do the following:
1. Start the Setup Utility program. See “Starting the Setup Utility
program”.
2. Select Start Options.
3. Set Power-On Self-Test to Enhanced.
• BeforereplacinganyFRUs,ensurethatthelatestlevelofBIOSis
installed on the system. A down-level BIOS might cause false errors and unnecessary replacement of the system board.
Use the following procedure to help determine the cause of the problem:
1. Power-off the computer and all external devices.
2. Check all cables and power cords.
3. Set all display controls to the middle position.
4. Power-on all external devices.
13
Page 17
Hardware Maintenance Manual
14
5. Power-on the computer.
• Lookfordisplayederrorcodes
• Listenforbeepcodes
• Lookforreadableinstructionsoramainmenuonthedisplay.
If you did not receive the correct response, proceed to step 6. If you do receive the correct response, proceed to step 7.
6. Look at the following conditions and follow the instructions:
• IfyouhearbeepcodesduringPOST,goto“Beep symptoms”.
• IfthecomputerdisplaysaPOSTerror,goto“POST error codes”.
• Ifthecomputerhangsandnoerrorisdisplayed,continueatstep7.
7. If you cannot continue, replace the last device tested.
Problem determination tips
Due to the variety of hardware and software combinations that can be encountered, use the following information to assist you in problem determination. If possible, have this information available when requesting assistance from Service Support and Engineering functions.
Machine type and model• Processor or hard disk upgrades• Failure symptom • – Do diagnostics indicate a failure? – What, when, where, single, or multiple systems? – Is the failure repeatable? – Has this configuration ever worked? – If it has been working, what changes were made prior to it failing? – Is this the original reported failure? Diagnostics version • – Type and version level Hardware configuration • – Print (print screen) configuration currently in use – BIOS level Operating system software • – Type and version level
Note: To eliminate confusion, identical systems are considered identical
only if they:
1. Are the exact machine type and models
2. Have the same BIOS level
3. Have the same adapters/attachments in the same locations
4. Have the same address jumpers/terminators/cabling
5. Have the same software versions and levels
6. Have the same configuration options set in the system
7. Have the same setup for the operation system control files
Page 18
Chapter 4. General Checkout
15
Comparing the configuration and software set-up between “working and non-working” systems will often lead to problem resolution.
Page 19
Hardware Maintenance Manual
16
Using the Setup Utility (Type G33)
The Setup Utility program is used to view and change the configuration settings of your computer, regardless of which operating system you are using. However, the operating-system settings might override any similar settings in the Setup Utility program.
Starting the Setup Utility program
5
To start the Setup Utility program, do the following:
1. If your computer is already on when you start this procedure, shut down the operating system and turn off the computer.
2. Press and hold the F1 key then turn on the computer. When you hear multiple beeps, release the F1 key.
Notes:
a. If you are using a USB keyboard and the Setup Utility program does
not display using this method, repeatedly press and release the F1 key rather than leaving it pressed when turning on the computer.
b. If a user password or an administrator password has been set, the
Setup Utility program menu is not displayed until you type your password. For more information, see “Using passwords.”
The Setup Utility might start automatically when POST detects that hardware has been removed or new hardware has been installed in your computer.
Viewing and changing settings
The Setup Utility program menu lists items that identify system configuration topics. To view or change settings, see “Starting the Setup Utility program.”
When working with the Setup Utility program menu, you must use the
Page 20
Chapter 5. Using the Setup Utility
17
keyboard. The keys used to perform various tasks are displayed on the right side of each screen.
Using passwords
By using the Setup Utility program, you can set passwords to prevent unauthorized persons from gaining access to your computer and data. See “Starting the Setup Utility program.” The following types of passwords are available:
• SupervisorPassword
• UserPassword
You do not have to set any passwords to use your computer. However, if you decide to set any passwords, read the following sections.
Password considerations
A password can be any combination of up to ten characters (a-z and 0-9) and symbols. For security reasons, it is a good idea to use a strong password that cannot be easily compromised. We suggest the passwords should adhere to the following rules:
• Musthaveatleastsevencharactersinlength
• Containatleastonealphabeticcharacter,onenumericcharacter,and
one symbol
• Containatleastoneofthefollowingsymbols:,./`;‘[]
• Youcanalsousethespacebar
• SetupUtilityprogramandharddiskdrivepasswordsarenotcase
sensitive
• Notbeyournameoryourusername
• Notbeacommonwordoracommonname
• Besignicantlydierentfromyourpreviouspassword
Supervisor password
When a Supervisor Password is set, it deters unauthorized persons from changing configuration settings. If you are responsible for maintaining the settings of several computers, you might want to set a Supervisor Password.
After you set a Supervisor Password, a password prompt is displayed each time you try to access the Setup Utility program.
If both the supervisor and user passwords are set, you can type either
Page 21
Hardware Maintenance Manual
18
password. However, to change any configuration settings, you must use your supervisor password.
Setting, changing, and deleting a Supervisor password
To set, change, or delete a password, do the following:
Note: A password can be any combination of up to ten characters (A- Z, a-z,
1. Start the Setup Utility program (see “Starting the Setup Utility program” on page 16).
2. From the Setup Utility program menu, select Change Supervisor Password and press Enter.
3. The password dialog box will be displayed. Type the new password, and press Enter.
4. when prompted to confirm the password, type the password again. If you type the password correctly, the password will be installed.
and 0-9). For more information, see “Password considerations” on page 17.
To delete a previously set supervisor password, do the following :
Note: When prompted for a password, you must type your supervisor
password.
1. From the Setup Utility program menu, select Change Supervisor Password and press Enter.
2. when you type the supervisor password. a message will display that Enter New Password. Press Enter and a message will display that indicates the password has been disabled. After that, the user password will be disabled too if a user password has been installed.
3. Press any key to contine.
User Password
When a User Password is set, you cannot start the Setup Utility program until a valid password is typed from the keyboard.
You can set a user password after you set the supervisor password.
Setting, changing, and deleting a user password
To set, change, or delete a user password, do the following:
Note: A password can be any combination of up to ten characters(A-Z, a-z,
and 0-9).
1. Start the Setup Utility program (See ”Starting the Setup Utility program”.)
Page 22
Chapter 5. Using the Setup Utility
19
2. From the Setup Utility program menu, selet Change User Password and press Enter.
3. The password dialog box will be displayed. Type the new password, and press Enter.
4. when prompted to confirm the password, type the password again. If you type the password correctly, the password will be installed.
To delete a previously set user password, do the following :
Note: When prompted for a password, you must type your supervisor
password.
1. From the Setup Utility program menu, select Change User Password and press Enter.
2. when you type the user password. a message will display that Enter New Password. Press Enter and a message will display that indicates the password has been disabled.
3. Press any key to contine.
Security Options
After a Supervisor Password is set, the Security Options can be displayed in the menu of Advanced BIOS Features.
To set Security Options, do the following:
1. Start the Setup Utility program (See ”Starting the Setup Utility program”.)
2. From the Setup Utility program menu, selet Change Supervisor
Password.
3. Set the Supervisor Password .
4. After that, Select Advanced BIOS Features.
5.Select Security Options.
6. Select Setup or Always and press Enter.
7. Return to the Setup Utility program menu and select press ESC to return the Advanced BIOS Features or press F10 to Save configuration changes and exit setup.
Notes:
a. If you choose Setup of the Security Options, the Setup Utility
program does not display until you type your password. But you can start other programs without the password.
b. If you choose Always of the Security Options, You can’t start any
program until you type your password.
Page 23
Hardware Maintenance Manual
20
Using Device
Device is used to enable or disable user access to the following device:
OnBoard SiS USB1.1 Controller When this feature is set to Disable, the
To set Device, do the following:
1. Start the Setup Utility program (see “Starting the Setup Utility program” on page 16).
2. From the Setup Utility program menu, select Integrated Periphrals.
3. Select Onboard Device.
4. Select OnBoard SiS USB1.1 Controller.
5. Select Disable or Enable and press Enter.
6. Return to the Setup Utility program menu and select Exit and then Save changes and Exit.
device of USB1.1 is disabled and will not be displayed in the system configuration.
Note: If you do not want to save the settings, select Discard Changes
and Exit or Discard Changes. You can set others such as OnBoard SiS USB2.0 Controller, USB Keyboard Legacy Support, USB Mouse Legacy Support, Onboard Audio DEVICE, Onboard LAN Control, Boot from Onboard LAN and so on. See the information
displayed on the right side of the screen.
Selecting a startup device
If your computer does not start up (boot) from a device such as the CD-ROM, diskette, or hard disk as expected, use one of the following procedures to select a startup device.
Selecting a temporary startup device
Use this procedure to startup from any boot device.
Note: Not all CDs, hard disks, and diskettes are bootable.
1. Turn off your computer.
2. Press and hold the F12 key then turn on the computer. When the Startup Device Menu appears, release the F12 key.
Note: If you are using a USB keyboard and the Startup Device Menu
does not display using this method, repeatedly press and release
Page 24
Chapter 5. Using the Setup Utility
21
the F12 key rather than leaving it pressed when turning on the computer.
3. Select the desired startup device from the Startup Device Menu and press Enter to begin.
Note: Selecting a startup device from the Startup Device menu does
not permanently change the startup sequence.
Selecting or changing the startup device sequence
To view or permanently change the configured startup device sequence, do the following:
1. Start the Setup Utility program (see “Starting the Setup Utility program” on page 16).
2. Select Advanced BIOS Features.
3. Select the devices for the 1st Boot Device, the 2nd Boot Device, the 3rd Boot Deviece and the 4th Boot Device.
4. Press ESC to return the Advanced BIOS Features and then Save changes and Exit.
If you have changed these settings and want to return to the default settings, select Load Optimal Defaults on the Setup Utility menu.
Exiting from the Setup Utility program
When you finish viewing or changing settings, press Esc to return to the Setup Utility program menu (you might have to press Esc several times). If you want to save the new settings, select Save changes and Exit before you exit. Otherwise, your changes will not be saved.
Page 25
Hardware Maintenance Manual
22
Using the Setup Utility (Type G43)
The Setup Utility program is used to view and change the configuration settings of your computer, regardless of which operating system you are using. However, the operating-system settings might override any similar settings in the Setup Utility program.
Starting the Setup Utility program
6
To start the Setup Utility program, do the following:
1. If your computer is already on when you start this procedure, shut down the operating system and turn off the computer.
2. Press and hold the F1 key then turn on the computer. When you hear multiple beeps, release the F1 key.
Notes:
a. If you are using a USB keyboard and the Setup Utility program does
not display using this method, repeatedly press and release the F1 key rather than leaving it pressed when turning on the computer.
b. If a user password or an supervisor password has been set, the Setup
Utility program menu is not displayed until you type your password. For more information, see “Using passwords.”
The Setup Utility might start automatically when POST detects that hardware has been removed or new hardware has been installed in your computer.
Viewing and changing settings
The Setup Utility program menu lists items that identify system configuration topics. To view or change settings, see “Starting the Setup Utility program.”
When working with the Setup Utility program menu, you must use the
Page 26
Chapter 5. Using the Setup Utility
23
keyboard. The keys used to perform various tasks are displayed on the right side of each screen.
Using passwords
By using the Setup Utility program, you can set passwords to prevent unauthorized persons from gaining access to your computer and data. See “Starting the Setup Utility program.” The following types of passwords are available:
• SetAdministratorPassword
• SetPower-OnPassword
You do not have to set any passwords to use your computer. However, if you decide to set any passwords, read the following sections.
Password considerations
A password can be any combination of up to ten characters (a-z and 0-9) and symbols. For security reasons, it is a good idea to use a strong password that cannot be easily compromised. We suggest the passwords should adhere to the following rules:
• Containatleastonealphabeticcharacter,onenumericcharacter.
• Notbeyournameoryourusername
• Notbeacommonwordoracommonname
• Besignicantlydierentfromyourpreviouspassword
Administrator password
When a Administrator Password is set, it deters unauthorized persons from changing configuration settings. If you are responsible for maintaining the settings of several computers, you might want to set a administrator Password.
After you set a Administrator Password, a password prompt is displayed each time you try to access the Setup Utility program.
If both the Administrator and Power-On are set, you can type either password. However, to change any configuration settings, you must use your administrator password.
Page 27
Hardware Maintenance Manual
24
Setting, changing, and deleting a Administrator password
To set, change, or delete a password, do the following:
Note: A password can be any combination of up to ten characters (A- Z, a-z,
1. Start the Setup Utility program (see “Starting the Setup Utility program” on page 16).
2. From the Setup Utility program menu, select Security .
3. Select Setup Administrator Password and press Enter.
4. The password dialog box will be displayed. Type the new password, and press Enter.
5. when prompted to confirm the password, type the password again. If you type the password correctly, the password will be installed.
To delete a previously set admministrator password, do the following :
and 0-9). For more information, see “Password considerations” on page 17.
Note: When prompted for a password, you must type your administrator
password.
1. From the Setup Utility program menu, select Setup Administrator Password and press Enter.
2. when you type the administrator password. a message will display that Enter New Password. Press Enter and a Setup Notice will display that indicates Password Uninstalled.
3. Press any key to contine.
Power-On Password
When a Power-On Password is set, you cannot start the Setup Utility program until a valid password is typed from the keyboard.
You should set Power-On password after you set the Administrator password. If you didn’t setup the administrator password but only set the user password, you cannot change any configuration settings.
Setting, changing, and deleting a user password
To set, change, or delete a user password, do the following:
Note: A password can be any combination of up to ten characters(A-Z, a-z,
and 0-9).
1. Start the Setup Utility program (See ”Starting the Setup Utility program”.)
2. From the Setup Utility program menu, selet Set Power-On Password and press Enter.
Page 28
Chapter 5. Using the Setup Utility
25
3. The password dialog box will be displayed. Type the new password, and press Enter.
4. when prompted to confirm the password, type the password again. If you type the password correctly, the password will be installed.
To delete a previously set user password, do the following :
Note: When prompted for a password, you must type your administrator
password.
1. From the Setup Utility program menu, select Set Power-On Password and press Enter.
2. when you type the user password. a message will display that Enter New Password. Press Enter and a Setup Notice will display that indicates Password Uninstalled.
3. Press any key to contine.
Using Device
Device is used to enable or disable user access to the following device:
Floppy Drive Setup When this feature is set to Disable, the device of Floppy Drive Setup is disabled and will not be displayed in the system configuration.
To set Device, do the following:
1. Start the Setup Utility program (see “Starting the Setup Utility program” on page 16).
2. From the Setup Utility program menu, select Device.
3. Select Floppy Drives Setup and press Enter. .
4. Select Disable or other related items and press Enter.
5. Return to the Setup Utility program menu and press F10 to save changes and exit setup..
Note: If you do not want to save the settings, select Serial Port Setup,
Parallel Port Setup, USB Setup, ATA Drives Setup, Video Setup, Audio Setup, Network Setup. and so on. See the information
displayed on the right side of the screen.
Page 29
Hardware Maintenance Manual
26
Selecting a startup device
If your computer does not start up (boot) from a device such as the CD-ROM, diskette, or hard disk as expected, use one of the following procedures to select a startup device.
Selecting a temporary startup device
Use this procedure to startup from any boot device.
Note: Not all CDs, hard disks, and diskettes are bootable.
1. Turn off your computer.
2. Press and hold the F12 key then turn on the computer. When the Startup Device Menu appears, release the F12 key.
Note: If you are using a USB keyboard and the Startup Device Menu
does not display using this method, repeatedly press and release the F12 key rather than leaving it pressed when turning on the computer.
3. Select the desired startup device from the Startup Device Menu and press Enter to begin.
Note: Selecting a startup device from the Startup Device menu does
not permanently change the startup sequence.
Selecting or changing the startup device sequence
To view or permanently change the configured startup device sequence, do the following:
1. Start the Setup Utility program (see “Starting the Setup Utility program” on page 16).
2. Select StartUp.
3. Select Primary Boot Sequence.
4. Select the devices for the 1st Boot Device, the 2nd Boot Device, the 3rd Boot Deviece and the 4th Boot Device.
5. Press ESC to return the Primary Boot Sequence. and then Save changes and Exit.
If you have changed these settings and want to return to the default settings, select Load Optimal Defaults on the Setup Utility menu.
Page 30
Chapter 5. Using the Setup Utility
27
Exiting from the Setup Utility program
When you finish viewing or changing settings, press Esc to return to the Setup Utility program menu (you might have to press Esc several times). If you want to save the new settings, select Save changes and Exit before you exit. Otherwise, your changes will not be saved.
Page 31
Hardware Maintenance Manual
28
Using the Setup Utility (Type G31)
The Setup Utility program is used to view and change the configuration settings of your computer, regardless of which operating system you are using. However, the operating-system settings might override any similar settings in the Setup Utility program.
Starting the Setup Utility program
7
To start the Setup Utility program, do the following:
1. If your computer is already on when you start this procedure, shut down the operating system and turn off the computer.
2. Press and hold the F1 key then turn on the computer. When you hear multiple beeps, release the F1 key.
Notes:
a. If you are using a USB keyboard and the Setup Utility program does
not display using this method, repeatedly press and release the F1 key rather than leaving it pressed when turning on the computer.
b. If a user password or an supervisor password has been set, the Setup
Utility program menu is not displayed until you type your password. For more information, see “Using passwords.”
The Setup Utility might start automatically when POST detects that hardware has been removed or new hardware has been installed in your computer.
Viewing and changing settings
The Setup Utility program menu lists items that identify system configuration topics. To view or change settings, see “Starting the Setup Utility program.”
When working with the Setup Utility program menu, you must use the
Page 32
Chapter 5. Using the Setup Utility
29
keyboard. The keys used to perform various tasks are displayed on the right side of each screen.
Using passwords
By using the Setup Utility program, you can set passwords to prevent unauthorized persons from gaining access to your computer and data. See “Starting the Setup Utility program.” The following types of passwords are available:
• SupervisorPassword
• UserPassword
You do not have to set any passwords to use your computer. However, if you decide to set any passwords, read the following sections.
Password considerations
A password can be any combination of up to ten characters (a-z and 0-9) and symbols. For security reasons, it is a good idea to use a strong password that cannot be easily compromised. We suggest the passwords should adhere to the following rules:
• Musthaveatleastsevencharactersinlength
• Containatleastonealphabeticcharacter,onenumericcharacter.
• SetupUtilityprogramandharddiskdrivepasswordsarenotcase
sensitive
• Notbeyournameoryourusername
• Notbeacommonwordoracommonname
• Besignicantlydierentfromyourpreviouspassword
Supervisor password
When a Supervisor Password is set, it deters unauthorized persons from changing configuration settings. If you are responsible for maintaining the settings of several computers, you might want to set a Supervisor Password.
After you set a Supervisor Password, a password prompt is displayed each time you try to access the Setup Utility program.
If both the supervisor and user passwords are set, you can type either password. However, to change any configuration settings, you must use your supervisor password.
Page 33
Hardware Maintenance Manual
30
Setting, changing, and deleting a Supervisor password
To set, change, or delete a password, do the following:
Note: A password can be any combination of up to ten characters (A- Z, a-z,
1. Start the Setup Utility program (see “Starting the Setup Utility program” on page 16).
2. From the Setup Utility program menu, select Security .
3. Select Change Supervisor Password and press Enter.
4. The password dialog box will be displayed. Type the new password, and press Enter.
5. when prompted to confirm the password, type the password again. If you type the password correctly, the password will be installed.
To delete a previously set supervisor password, do the following :
and 0-9). For more information, see “Password considerations” on page 17.
Note: When prompted for a password, you must type your supervisor
password.
1. From the Setup Utility program menu, select Change Supervisor Password and press Enter.
2. when you type the supervisor password. a message will display that Enter New Password. Press Enter and a message will display that indicates the password has been disabled. After that, the user password will be disabled too if a user password has been installed.
3. Press any key to contine.
User Password
When a User Password is set, you cannot start the Setup Utility program until a valid password is typed from the keyboard.
You should set a user password after you set the supervisor password. If you didn’t setup the supervisor password but only set the user password, you cannot change any configuration settings.
Setting, changing, and deleting a user password
To set, change, or delete a user password, do the following:
Note: A password can be any combination of up to ten characters(A-Z, a-z,
and 0-9).
1. Start the Setup Utility program (See ”Starting the Setup Utility program”.)
2. From the Setup Utility program menu, selet Change User Password and
Page 34
Chapter 5. Using the Setup Utility
31
press Enter.
3. The password dialog box will be displayed. Type the new password, and press Enter.
4. when prompted to confirm the password, type the password again. If you type the password correctly, the password will be installed.
To delete a previously set user password, do the following :
Note: When prompted for a password, you must type your supervisor
password.
1. From the Setup Utility program menu, select Change User Password and press Enter.
2. when you type the user password. a message will display that Enter New Password. Press Enter and a message will display that indicates the password has been disabled.
3. Press any key to contine.
Using Device
Device is used to enable or disable user access to the following device:
PS/2 Mouse Support When this feature is set to Disable, the device of PS/2 Mouse Support is disabled and will not be displayed in the system configuration.
To set Device, do the following:
1. Start the Setup Utility program (see “Starting the Setup Utility program” on page 16).
2. From the Setup Utility program menu, select Device.
3. Select Onboard PS/2 Mouse Support.
4. Select Disable or Enable and press Enter.
5. Return to the Setup Utility program menu and select Exit and then Save
changes and Exit.
Note: If you do not want to save the settings, select Discard Changes
and Exit or Discard Changes. You can set others such as Floppy Drive Setup, Serial Port Setup, Parallet Port Setup, USB Setup, Video Setup, Audio Setup, Network Setup and so on. See the
information displayed on the right side of the screen.
Page 35
Hardware Maintenance Manual
32
Selecting a startup device
If your computer does not start up (boot) from a device such as the CD-ROM, diskette, or hard disk as expected, use one of the following procedures to select a startup device.
Selecting a temporary startup device
Use this procedure to startup from any boot device.
Note: Not all CDs, hard disks, and diskettes are bootable.
1. Turn off your computer.
2. Press and hold the F12 key then turn on the computer. When the Startup Device Menu appears, release the F12 key.
Note: If you are using a USB keyboard and the Startup Device Menu
does not display using this method, repeatedly press and release the F12 key rather than leaving it pressed when turning on the computer.
3. Select the desired startup device from the Startup Device Menu and press Enter to begin.
Note: Selecting a startup device from the Startup Device menu does
not permanently change the startup sequence.
Selecting or changing the startup device sequence
To view or permanently change the configured startup device sequence, do the following:
1. Start the Setup Utility program (see “Starting the Setup Utility program” on page 16).
2. Select StartUp.
3. Select Primary Boot Sequence.
4. Select the devices for the 1st Boot Device, the 2nd Boot Device, the 3rd Boot Deviece and the 4th Boot Device.
5. Press ESC to return the Primary Boot Sequence. and then Save changes and Exit.
If you have changed these settings and want to return to the default settings, select Load Optimal Defaults on the Setup Utility menu.
Page 36
Chapter 5. Using the Setup Utility
33
Exiting from the Setup Utility program
When you finish viewing or changing settings, press Esc to return to the Setup Utility program menu (you might have to press Esc several times). If you want to save the new settings, select Save changes and Exit before you exit. Otherwise, your changes will not be saved.
Page 37
Hardware Maintenance Manual
34
Symptom-to-FRU Index
The Symptom-to-FRU index lists error symptoms and possible causes. The most likely cause is listed first. Always begin with Chapter 4, “General Checkout,” on page 13. This index can also be used to help you decide which FRUs to have available when servicing a computer. If you are unable to correct the problem using this index, go to “Undetermined problems” on page 27.
Notes
8
• Ifyouhavebothanerrormessageandanincorrectaudioresponse
diagnose the error message first.
• Ifyoucannotrunthediagnostictestsoryougetadiagnosticerror
code when running a test but did receive a POST error message diagnose the POST error message first.
• Ifyoudidnotreceiveanyerrormessagelookforadescriptionof
your error symptoms in the first part of this index.
Hard disk drive boot error
A hard disk drive boot error (error codes 1962 and I999030X) can have the following causes.
Error FRU/Action
The start-up drive is not in the boot sequence in configuration.
No operating system installed on the boot drive.
Check the configuration and ensure the start-up drive is in the boot sequence.
Install an operating system on the boot drive.
Page 38
Chapter 6. Symptom-to-FRU Index
35
Error FRU/Action
The boot sector on the start-up drive is corrupted.
The drive is defective. Replace the hard disk drive.
Power Supply Problems
If you suspect a power problem, use the following procedures.
Check/Verify FRU/Action
Check the following for proper installation.
Power Cord• On/Off Switch connector• On/Off Switch Power Supply • connector System Board Power Supply • connectors
Microprocessor(s) connection• Check the power cord for continuity. Power Cord Check the power-on switch for continuity.
The drive must be formatted do the following:
1. Attempt to back-up the data on the failing hard disk drive.
2. Using the operating systems programs format the hard disk drive.
Reseat connectors
Power-on Switch
Page 39
Hardware Maintenance Manual
36
Beep symptoms
Beep symptoms are tones or a series of tones separated by pauses (intervals without sound) during POST.
The following tables describes beep symptoms.
Beep Symptom FRU/Action 1 beep
Memory refresh timer error
2 beeps
Parity error in base memory (first 64KB block)
3 beeps
Base memory read/write test error
Reseat the memory, or replace with known good modules.
4 beeps
Motherboard timer not operational
5 beeps
Processor error
6 beeps
8042 Gate A20 test error (cannot switch to protected mode)
7 beeps
General exception error (processor exception interrupt error)
8 beeps
Display memory error (system video adapter)
Fatal error indicating a serious problem with the system. Consult your system manufacturer. Before declaring the motherboard beyond all hope, eliminate the possibility of interference by a malfunctioning add-in card. Remove all expansion cards except the video adapter.
• Ifbeepcodesaregenerated
when all other expansion cards are absent, consult your system manufacturer’s technical support.
• Ifbeepcodesarenotgenerated
when all other expansion cards are absent, one of the add-in cards is causing the malfunction. Insert the cards back into the system one at a time until the problem happens again. This will reveal the
malfunctioning card. If the system video adapter is an add-in card, replace or reseat the video adapter. If the video adapter is an integrated part of the system board, the board may be faulty.
Page 40
Chapter 6. Symptom-to-FRU Index
37
Beep Symptom FRU/Action 9 beeps
AMIBIOS ROM checksum error
10 beeps
CMOS shutdown register read/write error
11 beeps
Cache memory test failed
Fatal error indicating a serious problem with the system. Consult your system manufacturer. Before declaring the motherboard beyond all hope, eliminate the possibility of interference by a malfunctioning add-in card. Remove all expansion cards except the video adapter.
• Ifbeepcodesaregenerated
when all other expansion cards are absent, consult your system manufacturer’s technical support.
• Ifbeepcodesarenotgenerated
when all other expansion cards are absent, one of the add-in cards is causing the malfunction. Insert the cards back into the system one at a time until the problem happens again. This will reveal the malfunctioning card.
POST error codes
Each time you power-on the system, it performs a series of tests that check the operation of the system and some options. This series of tests is called the Power-On Self-Test, or POST. POST does the following operations.
• Checkssomebasicsystem-boardoperations
• Checksthememoryoperation
• Startsthevideooperation
• Veriesthatthebootdriveisworking
If the POST detects a problem, an error message appears on the screen. A single problem can cause several error messages to appear. When you correct the cause of the first error message, the other error messages probably will not appear on the screen the next time you turn on the system.
Page 41
Hardware Maintenance Manual
38
POST Error Message Description/Action
CMOS Date/Time Not Set The CMOS Date and/or Time are
CMOS Battery Low The CMOS battery is no longer
CMOS Checksum Bad Checksum of CMOS is incorrect.
Primary Master Hard Disk Error The IDE/ATAPI device configured
Primary Slave Hard Disk Error
Secondary Master Hard Disk Error
Secondary Slave Hard Disk Error
invalid. This error can be resolved by readjusting the system time in AMIBIOS Setup.
functional. Replace the battery.
The computer loads the default configuration settings. This error might indicate that CMOS has become corrupt due to a weak CMOS battery.
as Primary Master/Primary Slave/ Secondary Master/Secondary Slave could not be found or initialized. Make sure the hard drive is correctly installed.
PS2 Mouse not found PS2 Mouse support is enabled in
the BIOS setup butthe device is not detected. You can plug PS2 Mouse or set PS2 Mouse support is auto.
Keyboard error Cannot initialize the keyboard.
Make sure the keyboard is properly connected to the computer and that no keys are held pressed during POST. To purposely configure the computer without a keyboard, set keyboardless operation in Setup to Enable. The BIOS then ignores the missing keyboard during POST.
System Halted The system has been halted. A reset
or power cycle is required to reboot the machine. This message appears after a fatal error has been detected.
Press TAB to show POST screen Pressing the TAB key permits the
user to toggle between the default POST display screen and a custom POST display screen.
Page 42
Chapter 6. Symptom-to-FRU Index
39
POST Error Message Description/Action
Reboot and Select proper Boot device or Insert Boot Media in selected Boot device
Undetermined problems
If this computer has a parallel ATA hard disk drive, make sure that the hard disk drive is jumpered as a master and the optical drive is jumpered as a slave.
1. Power-off the computer.
2. Remove or disconnect the following components (if installed) one at a time. a. External devices (modem, printer, or mouse) b. Any adapters c. Memory modules d. Extended video memory e. External Cache f. External Cache RAM g. Hard disk drive h. Diskette drive
3. Power-on the computer to re-test the system.
4. Repeat steps 1 through 3 until you find the failing device or adapter.
The BIOS was unable to find a suitable boot device. Make sure the boot drive is properly connected to the computer. Make sure you have bootable media.
If all devices and adapters have been removed, and the problem continues, replace the system board.
Page 43
Hardware Maintenance Manual
40
Replacing hardware
Attention
Do not remove the computer cover or attempt any repair before reading the “Important safety information” in the Safety and Warranty
Guide that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer. To obtain copies of
the Safety and Warranty Guide or HMM, go to the Support Web site at http://www.lenovo.com/support.
9
Note
Use only parts provided by Lenovo.
Removing the computer cover
Important
Turn off the computer and wait 3 to 5 minutes to let the computer cool before removing the computer cover.
To remove the computer cover:
1. Remove any media (diskettes, CDs, or tapes) from the drives, shut down your operating system, turn off all attached devices, and the computer.
2. Unplug all power cords from electrical outlets.
3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to “Locating connectors on the front of the computer” and “Locating connectors on the rear of the computer”.
4. Remove any locking devices that secure the computer cover.
Page 44
Chapter 7. Replacing hardware
41
5. Pull down the switch at the rear of the chassis and slide the computer cover to the rear to remove.
Page 45
Hardware Maintenance Manual
42
Removing and replacing the front bezel
To remove and replace the front bezel:
1. Remove the computer cover. Refer to “Removing the computer cover”.
2. Remove the front bezel by releasing the three plastic tabs inside the chassis and push the bezel outward as shown.
3. To reinstall the bezel, align the plastic tabs on the bottom of the bezel with the corresponding holes in the chassis, then snap it into position at the bottom and top of the chassis.
4. Refer to the “Completing the installation”.
Page 46
Chapter 7. Replacing hardware
43
Replacing the power supply
Attention
Do not remove the computer cover or attempt any repair before reading the “Important safety information” in the Safety and Warranty
Guide that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer. To obtain copies of
the Safety and Warranty Guide or HMM, go to the Support Web site at http://www.lenovo.com/support.
To replace the power supply:
1. Remove the computer cover. Refer to “Removing the computer cover”.
Note: For this procedure, it helps to lay the computer on its side.
2. Disconnect the power supply cables from the system board and from all drives. Refer to “Identifying parts on the system board”.
3. Remove the four screws that secure the power supply at the rear of the chassis.
4. Lift the power supply out of the chassis.
5. Install the new power supply into the chassis so that the screw holes in the power supply align with those in the chassis.
6. Install the four screws to secure the power supply. Note: Use only the screws provided by Lenovo.
7. Reconnect the power supply connectors to the system board.
Page 47
Hardware Maintenance Manual
44
8. Reconnect a power supply connector to each of the drives.
9. Refer to the “Completing the installation”.
Replacing the heat sink assembly
Attention
Do not remove the computer cover or attempt any repair before reading the “Important safety information” in the Safety and Warranty
Guide that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer. To obtain copies of
the Safety and Warranty Guide or HMM, go to the Support Web site at http://www.lenovo.com/support.
To replace the heat sink assembly:
1. Remove the computer cover. Refer to “Removing the computer cover”.
2. Lay the computer on its side.
3. Locate the heat sink. Refer to “Identifying parts on the system board”.
4. Disconnect the heat sink and the fan assembly cable from the system board.
5. Remove the four screws the system board.
securing the heat sink and fan assembly to
6. Lift the failing heat sink and fan assembly off the system board.
7. Use the thermal grease syringe to place five drops of grease on the top of the microprocessor. Each drop of grease should be 0.03ml (3 tick marks on the grease syringe).
Page 48
Chapter 7. Replacing hardware
45
8. Install the heat sink and fan assembly on the heat sink retention bracket.
9. Reconnect the disconnected cables to the system board.
10. Refer to the” Completing the installation”.
Replacing a memory module
Attention
Do not remove the computer cover or attempt any repair before reading the “Important safety information” in the Safety and Warranty
Guide that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer. To obtain copies of
the Safety and Warranty Guide or HMM, go to the Support Web site at http://www.lenovo.com/support.
To replace a memory module:
1. Remove the computer cover. Refer to “Removing the computer cover”.
Note: For this procedure, it helps to lay the computer on its side.
2. Locate the memory module connectors. Refer to “Locating components”.
3. Remove the memory module being replaced by opening the retaining clips as shown.
Page 49
Hardware Maintenance Manual
46
4. Position the new memory module over the memory connector. Make sure the notch key on the system board. Push the memory module straight down into the connector until the retaining clips close.
on the memory aligns correctly with the connector
5. Refer to the “Completing the installation”.
Replacing an adapter
Attention
Do not remove the computer cover or attempt any repair before reading the “Important safety information” in the Safety and Warranty
Guide that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer. To obtain copies of
the Safety and Warranty Guide or HMM, go to the Support Web site at http://www.lenovo.com/support.
To replace an adapter:
1. Remove the computer cover. Refer to “Removing the computer cover”.
2. At the rear of the computer, press the release button adapter latch and remove the adapter by pulling it straight out of the adapter connector.
to open the
Page 50
Chapter 7. Replacing hardware
47
3. Install the new adapter into the same adapter connector.
4. Ensure the adapter is fully seated into the adapter connector.
5. At the rear of the computer, pivot the adapter latch to the closed
Page 51
Hardware Maintenance Manual
48
position to secure the adapter.
6. Refer to the “Completing the installation”.
Note: Replacement of some models equipped with graphic adapter bracket is different.
Please remove the bracket first as the following:
1. Remove the two screws that secure the bracket at the bottom of the chassis.
2. Lift the bracket out of the chassis.
3. Then remove the adapter as above.
After the Graphic Adapter is installed , install the bracket as the following:
1. Install the bracket into the chassis so that the screw holes in the bracket align with those in the chassis. Let the slot on the bracket clip the adapter.
2. Install the two screws to secure the bracket. Note: Use only the screws provided by Lenovo.
Page 52
Chapter 7. Replacing hardware
49
Replacing the hard disk drive
Attention
Do not remove the computer cover or attempt any repair before reading the “Important safety information” in the Safety and Warranty
Guide that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer. To obtain copies of
the Safety and Warranty Guide or HMM, go to the Support Web site at http://www.lenovo.com/support.
Important
When you receive a new hard disk drive, you will also receive a set of Operating System Recovery CD. The set of Operating System Recovery CD will enable you to restore the Operating System of the hard disk. For more information on recovering factory-installed software, refer to “OneKey Recovery” in the User Guide.
To replace the hard disk drive:
1. Remove the computer cover. Refer to “Removing the computer cover”.
Note: For this procedure, it helps to lay the computer on its side.
2. Disconnect the signal and power cables from the hard disk drive.
Page 53
Hardware Maintenance Manual
50
3. Use the blue handle to remove hard disk drive from drive bay.
4. Slide the new hard disk drive into the drive bay.
5. Pivot in the drive bay in place.
6. Connect the power and signal cables to the hard disk drive. Refer to “Identifying parts on the system board”.
7. Refer to the “Completing the installation”.
Replacing an optical drive
Attention
Do not remove the computer cover or attempt any repair before reading the “Important safety information” in the Safety and Warranty
Guide that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer. To obtain copies of
the Safety and Warranty Guide or HMM, go to the Support Web site at http://www.lenovo.com/support.
To replace an optical drive
1. Remove the computer cover. Refer to “Removing the computer cover”.
2. Remove the front bezel. Refer to “Removing and replacing the front bezel”.
3. Disconnect the signal and power cables from the rear of the optical drive.
Page 54
Chapter 7. Replacing hardware
51
4. Press the release button and remove the optical drive out the front of the computer.
5. Slide the new optical drive into the bay from the front until it snap into position.
6. Connect the signal and power cables to the drive.
7. Install the front bezel. Refer to “Removing and replacing the front bezel”.
8. Refer to the “Completing the installation”.
Page 55
Hardware Maintenance Manual
52
Replacing the system fan assembly
Attention
Do not remove the computer cover or attempt any repair before reading the “Important safety information” in the Safety and Warranty
Guide that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer. To obtain copies of
the Safety and Warranty Guide or HMM, go to the Support Web site at http://www.lenovo.com/support.
To replace the system fan assembly:
1. Remove the computer cover. Refer to “Removing the computer cover”.
2. Locate the system fan assembly. Refer to “Identifying parts on the system board”.
3. Disconnect the system fan assembly cable from the system board. Refer to “Identifying parts on the system board”.
4. Pull the system fan assembly out of chassis.
5. Install the new system fan assembly by aligning the rubber mounts of the system fan assembly with the holes on the chassis and push the rubber mounts through the holes.
Page 56
Chapter 7. Replacing hardware
53
6. Pull on the tips of the rubber mounts until the fan assembly is in place.
7. Connect the system fan assembly cable to the system fan connector on the system board.
8. Refer to the “Completing the installation”.
Replacing the keyboard
Attention
Do not remove the computer cover or attempt any repair before reading the “Important safety information” in the Safety and Warranty
Guide that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer. To obtain copies of
the Safety and Warranty Guide or HMM, go to the Support Web site at http://www.lenovo.com/support.
To replace the keyboard:
1. Remove any media (diskettes, CDs, or tapes) from the drives, shut down your operating system, and turn off all attached devices and the computer.
Page 57
Hardware Maintenance Manual
54
2. Unplug all power cords from electrical outlets.
3. Locate the connector for the keyboard. Refer to “Locating connectors on the rear of the computer” and “Locating connectors on the front of the computer”.
Note: Your keyboard might be connected to the standard keyboard
connector either the front or rear of the computer.
4. Disconnect the failing keyboard cable from the computer and connect the new keyboard cable to the same connector.
5. Refer to the “Completing the installation”.
at the rear of the computer or to a USB connector at
Replacing the mouse
Attention
Do not remove the computer cover or attempt any repair before reading the “Important safety information” in the Safety and Warranty
Guide that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer. To obtain copies of
the Safety and Warranty Guide or HMM, go to the Support Web site at http://www.lenovo.com/support.
To replace the mouse:
1. Remove any media (diskettes, CDs, or tapes) from the drives, shut down your operating system, and turn off all attached devices and the computer.
2. Unplug all power cords from electrical outlets.
3. Locate the connector for the mouse. Refer to “Locating connectors on the front of the computer” and “Locating connectors on the rear of the computer”.
Note: Your mouse might be connected to the standard mouse
connector either the front or rear of the computer.
at the rear of the computer or to a USB connector at
Page 58
Chapter 7. Replacing hardware
55
4. Disconnect the failing mouse cable from the computer.
5. Connect the new mouse cable to the connector.
6. Refer to the “Completing the installation.”
Replacing the External speaker
1. Remove any media (diskettes, CDs, or tapes) from the drives, shut down the computer, and turn off all attached devices.
2. Unplug all power cords from electrical outlets.
3. Locate the Speaker. Refer to “Locating connectors on the rear of the computer” and “Locating connectors on the front of the computer”. Your speaker might be connected to the Audio connector Audio connector at either the front or rear of the computer. Locate the connector for the speaker.
4. Disconnect the failing speaker cable from the computer and connect the new speaker cable to the same connector.
5. Refer to the “Completing the parts replacement”.
Completing the installation
After replacing the parts, you need to close the computer cover and reconnect cables, including telephone lines and power cords. Also, depending on the part that was replaced, you might need to confirm the updated information in the Setup Utility program. Refer to “Starting the Setup Utility” in the User Guide or in the Hardware Maintenance Manual.
to an
Page 59
Hardware Maintenance Manual
To complete the part installation:
1. Ensure that all components have been reassembled correctly and that no tools or loose screws are left inside your computer. Refer to “Locating components” for the location of the various components.
2. Make sure that the cables are routed correctly before replacing the computer cover.
3. Position the computer cover on the chassis so that the rail guides on the bottom of the computer cover engage the rails. Then, push the computer cover closed until it snaps into position.
56
4. If a cover lock is installed, lock the cover.
5. Reconnect the external cables and power cords into the computer. Refer to “Locating connectors on the front of the computer” and “Locating connectors on the rear of the computer”.
6. To update your configuration settings, refer to “Starting the Setup Utility” in the User Guide or in the Hardware Maintenance Manual.
Note: In most areas of the world, Lenovo requires the return of the
defective CRU. Information about this will come with the CRU or will come a few days after the CRU arrives.
Page 60
Additional Service Information
Chapter 8. Additional Service Information
(Type G33)
This chapter provides additional information that the service representative might find helpful.
Power management
Power management reduces the power consumption of certain components of the computer such as the system power supply, processor, hard disk drives, and some monitors.
Automatic configuration and power interface (ACPI) BIOS
Being an ACPI BIOS system, the operating system is allowed to control the power management features of the computer and the setting for Advanced Power Management (APM) BIOS mode is ignored. Not all operating systems support ACPI BIOS mode.
10
Automatic Power-On features
The Automatic Power-On features within the Power Management menu allow you to enable and disable features that turn on the computer automatically.
Resume On Ring: • With this feature set to Enabled, the computer will turn on automatically when a ring is detected on the internal modem. Resume On PME#: • This feature allows PCI cards that support this capability to wake the system. Resume On RTC: • You can specify a date and time at which the computer will be turned on automatically. This can be either a single event or a daily event. USB Device Wakeup From S3: • This feature allows USB Device to wake the System from S3.
57
Page 61
Hardware Maintenance Manual
Additional Service Information (Type G43)
This chapter provides additional information that the service representative might find helpful.
Power management
Power management reduces the power consumption of certain components of the computer such as the system power supply, processor, hard disk drives, and some monitors.
Automatic configuration and power interface (ACPI)
11
BIOS
Being an ACPI BIOS system, the operating system is allowed to control the power management features of the computer and the setting for Advanced Power Management (APM) BIOS mode is ignored. Not all operating systems support ACPI BIOS mode.
Power Management features
The Automatic Power-On features within the Power menu allow you to enable and disable features that turn on the computer automatically.
Wake On LAN: • This future allow system wake up by Lan card and onboard lan. Ring Wakeup:• With this feature set to Enabled, the computer will turn on automatically when a ring is detected on the internal modem. Wake Up On Alarm:• You can specify a date and time at which the computer will be turned on automatically. This can be either a single event or a daily event. PCI Wake Up: • This feature allows PCI cards which support this cappability to wake this system.
58
Page 62
Additional Service Information
Chapter 8. Additional Service Information
(Type G31)
This chapter provides additional information that the service representative might find helpful.
Power management
Power management reduces the power consumption of certain components of the computer such as the system power supply, processor, hard disk drives, and some monitors.
Automatic configuration and power interface (ACPI)
12
BIOS
Being an ACPI BIOS system, the operating system is allowed to control the power management features of the computer and the setting for Advanced Power Management (APM) BIOS mode is ignored. Not all operating systems support ACPI BIOS mode.
Automatic Power-On features
The Automatic Power-On features within the Power Management menu allow you to enable and disable features that turn on the computer automatically.
Resume On Ring: • With this feature set to Enabled, the computer will turn on automatically when a ring is detected on the internal modem. Resume On RTC Alarm: • You can specify a date and time at which the computer will be turned on automatically. This can be either a single event or a daily event. PCI/PCI-E/LAN Wake Up: • This feature allows PME cards which support this cappability to wake this system.
59
Page 63
Hardware Maintenance Manual
60
Statement
Thanks for using Lenovo products.
Carefully read all documents shipped with your computer before you install and use the product for the first time for better use of it. If you fail to operate the product according to instructions and requirements in all the manuals included with your computer, or operate the product inappropriately for reasons such as misunderstanding, Lenovo (Beijing) Co., Ltd. will not be responsible for any loss caused except those arising from the installation and operations carried out by Lenovo professional service staff.
A
Lenovo (Beijing) Co., Ltd. has performed strict collation for all the manuals included with your computer, but we cannot guarantee that it has no mistake and omission.
To provide better service, Lenovo (Beijing) Co., Ltd. reserves the right to improve and/or modify the products and software programs described in all the manuals included with your computer and the content of the manual at any time without additional notice.
All the manuals included with your computer is provided to help you use Lenovo products appropriately, but it does not represent any description of the software/hardware configuration for the product. For the configuration of the product, refer to related contract (if any), product packing list for the product or consult the distributor for the product sales.
The content of all the manuals included with your computer is protected by copyright laws and rules. All the manuals included with your computer may not be reproduced or transcribed by any means, or transmitted through wired or wireless network in any form, or translated into any language without prior written permission of Lenovo (Beijing) Co., Ltd. Copyright ©2007 Lenovo (Beijing) Co., Ltd. All rights reserved.
The software interface and hardware configuration involved in all the manuals included with your computer depends on the actual configuration of the computer you purchase.
Page 64
Appendix. Statement
61
Welcome to contact us for any inconsistency between the product and all the manuals included with your computer. For the latest information or any questions or comments, contact or visit Lenovo website:
Service website: http://www.lenovo.com
Lenovo is trademark of Lenovo (Beijing ) Co., Ltd.
Microsoft is the registered trademark of Microsoft.
Microsoft Windows XP is the Windows XP­registered trademark of Microsoft Corporation.
Intel Inside is the registered trademark of Intel.
AMD and the logo, AMD Athlon™, and AMD Opteron™
This is description of trademarks or registered trademarks of Lenovo and its partners.
Other registered trademarks mentioned in all the manuals included with your computer belong to the specific company respectively.
All rights reserved.
All the manuals included with your computer is protected by copyright laws. Any part of all the manuals included with your computer may not be reproduced or copied by any means without prior written permission of Lenovo (Beijing) Co., Ltd.
Names or marks of certain companies mentioned in all the manuals included with your computer or this document are only used to state trademark rights, and they will not necessarily indicate that related software or hardware is included. The concrete configuration of the product depends on the description of packing list.
AMD, the AMD logo, AMD Athlon and AMD Opteron are trademarks or registered trademarks of Advanced Micro Devices.
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use