Page 1
Hardware Maintenance Manual
IdeaPad 5 (14", 05), IdeaPad Slim 5 (14", 05), IdeaPad 5 (15", 05)，
IdeaPad Slim 5 (15", 05) and Lenovo Ducati 5
Page 2
First Edition (February 2020)
© Copyright Lenovo 2020.
Page 3
Contents
About this manual . . . . . . . . . . . . iii
Chapter 1. Safety information . . . . . . 1
General safety . . . . . . . . . . . . . . . . 1
Electrical safety . . . . . . . . . . . . . . . . 1
Safety inspection guide. . . . . . . . . . . . . 2
Handling devices that are sensitive to electrostatic
discharge . . . . . . . . . . . . . . . . . . 3
Grounding requirements . . . . . . . . . . . . 4
Safety notices (multilingual translations) . . . . . . 4
Chapter 2. General checkout . . . . . 21
What to do first . . . . . . . . . . . . . . . 21
CRU list . . . . . . . . . . . . . . . . . . 22
Chapter 3. Idetifying FRUs (CRUs) . . 23
Locate FRUs and CRUs . . . . . . . . . . . 23
Chapter 4. Removing a FRU or
CRU . . . . . . . . . . . . . . . . . . 29
Service tools . . . . . . . . . . . . . . . . 29
General guidelines. . . . . . . . . . . . . . 29
Removal procedure for IdeaPad 5 (14", 05),
IdeaPad Slim 5 (14", 05) and Lenovo Ducati 5 . . . 30
Remove the lower case . . . . . . . . . . 30
Remove the battery pack . . . . . . . . . 31
Remove the solid-state drive module. . . . . 32
Remove the Wi-Fi card . . . . . . . . . . 33
Remove the heat sink. . . . . . . . . . . 34
Remove the fan . . . . . . . . . . . . . 34
Remove the I/O board with cable . . . . . . 35
Remove the speaker . . . . . . . . . . . 36
Remove the system board . . . . . . . . . 37
Remove the LCD module . . . . . . . . . 39
Remove the upper case (with keyboard and
touch pad) . . . . . . . . . . . . . . . 40
Disassemble the LCD module . . . . . . . 41
Removal procedure for IdeaPad 5 (15”, 05) and
IdeaPad Slim 5 (15", 05) . . . . . . . . . . . 46
Remove the lower case . . . . . . . . . . 46
Remove the battery pack . . . . . . . . . 47
Remove the dummy hard disk drive module . . 47
Remove the solid-state drive . . . . . . . . 48
Remove the solid-state drive bracket . . . . 49
Remove the Wi-Fi card . . . . . . . . . . 49
Remove the RTC battery . . . . . . . . . 50
Remove the I/O board with cable . . . . . . 50
Remove the heat sink. . . . . . . . . . . 51
Remove the fan . . . . . . . . . . . . . 52
Remove the speaker . . . . . . . . . . . 53
Remove the system board . . . . . . . . . 53
Remove the LCD module . . . . . . . . . 55
Remove the upper case (with keyboard and
touch pad) . . . . . . . . . . . . . . . 56
Disassemble the LCD module . . . . . . . 56
Appendix A. Label locations. . . . . . 61
Trademarks . . . . . . . . . . . . . . . . lxiii
© Copyright Lenovo 2020 i
Page 4
ii Hardware Maintenance Manual
Page 5
About this manual
This manual contains service and reference information for the following Lenovo products.
Machine
IdeaPad 5 14IIL05 81YH
IdeaPad 5 14ARE05 81YM
IdeaPad 5 15IIL05 81YK
IdeaPad 5 15ARE05
Lenovo Ducati 5
Machine type (MT)
81YQ
82ES
Important:
• This manual is intended only for trained service technicians who are familiar with Lenovo products.
• Before servicing a Lenovo product, be sure to read all the information under Chapter 1 “Safety
information” on page 1.
© Copyright Lenovo 2020 iii
Page 6
iv Hardware Maintenance Manual
Page 7
Chapter 1. Safety information
This chapter presents the following safety information that you need to be familiar with before you service a
Lenovo notebook computer.
General safety
Follow these rules to ensure general safety:
• Observe good housekeeping in the area of the machines during and after maintenance.
• When lifting any heavy object:
1. Make sure that you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift.
4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the
muscles in your back. Do not attempt to lift any object that weighs more than 16 kg (35 lb) or that you
think is too heavy for you.
• Do not perform any action that causes hazards to the customer, or that makes the equipment unsafe.
• Before you start the machine, make sure that other service technicians and the customer's personnel are
not in a hazardous position.
• Place removed covers and other parts in a safe place, away from all personnel, while you are servicing the
machine.
• Keep your tool case away from walk areas so that other people will not trip over it.
• Do not wear loose clothing that can be trapped in the moving parts of a machine. Make sure that your
sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it.
• Insert the ends of your necktie or scarf inside clothing or fasten it with a non-conductive clip, about 8
centimeters (3 inches) from the end.
• Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing.
Attention: Metal objects are good electrical conductors.
• Wear safety glasses when you are hammering, drilling, soldering, cutting wire, attaching springs, using
solvents, or working in any other conditions that might be hazardous to your eyes.
• After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that
is worn or defective.
• Reinstall all covers correctly before returning the machine to the customer.
• Fan louvers on the machine help to prevent overheating of internal components. Do not obstruct fan
louvers or cover them with labels or stickers.
Electrical safety
Observe the following rules when working on electrical equipment.
Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft
material that does not insulate you when working with live electrical currents.Many customers have, near
their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges.
Do not use this type of mat to protect yourself from electrical shock.
• Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet. If an electrical
accident occurs, you can then operate the switch or unplug the power cord quickly.
• Do not work alone under hazardous conditions or near equipment that has hazardous voltages.
• Disconnect all power before:
– Performing a mechanical inspection
– Working near power supplies
© Copyright Lenovo 2020 1
Page 8
– Removing or installing main units
• Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer
to power-off the wall box that supplies power to the machine, and to lock the wall box in the off position.
• If you need to work on a machine that has exposed electrical circuits, observe the following precautions:
– Ensure that another person, familiar with the power-off controls, is near you.
Attention: Another person must be there to switch off the power, if necessary.
– Use only one hand when working with powered-on electrical equipment; keep the other hand in your
pocket or behind your back.
Attention: An electrical shock can occur only when there is a complete circuit. By observing the above
rule, you may prevent a current from passing through your body.
– When using testers, set the controls correctly and use the approved probe leads and accessories for
that tester.
– Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as
metal floor strips and machine frames.
Observe the special safety precautions when you work with very high voltages; Instructions for these
precautions are in the safety sections of maintenance information. Use extreme care when measuring high
voltages.
• Regularly inspect and maintain your electrical hand tools for safe operational condition.
• Do not use worn or broken tools and testers.
• Never assume that power has been disconnected from a circuit. First, check that it has been powered off.
• Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors,
non-grounded power extension cables, power surges, and missing safety grounds.
• Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is
conductive; such touching can cause personal injury and machine damage.
• Do not service the following parts with the power on when they are removed from their normal operating
places in a machine:
– Power supply units
– Pumps
– Blowers and fans
– Motor generators
– Similar units as listed above
This practice ensures correct grounding of the units.
• If an electrical accident occurs:
– Use caution; do not become a victim yourself.
– Switch off power.
– Send another person to get medical aid.
Safety inspection guide
The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each
machine was designed and built, required safety items were installed to protect users and service
technicians from injury. This guide addresses only those items. You should use good judgment to identify
potential safety hazards due to attachment of non-Lenovo features or options not covered by this inspection
guide.
If any unsafe conditions are present, you must determine how serious the apparent hazard could be and
whether you can continue without first correcting the problem.
Consider these conditions and the safety hazards they present:
• Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal
electrical shock)
• Explosive hazards, such as a damaged cathode ray tube (CRT) face or a bulging capacitor
• Mechanical hazards, such as loose or missing hardware
2
Hardware Maintenance Manual
Page 9
To determine whether there are any potentially unsafe conditions, use the following checklist at the
beginning of every service task. Begin the checks with the power off, and the power cord disconnected.
Checklist:
1. Check exterior covers for damage (loose, broken, or sharp edges).
2. Power off the computer. Disconnect the power cord.
3. Check the power cord for:
a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground
continuity for 0.1 ohm or less between the external ground pin and the frame ground.
b. The power cord should be the authorized type specified for your computer. Go to:
www.lenovo.com/serviceparts-lookup
c. Insulation must not be frayed or worn.
4. Check for cracked or bulging batteries.
5. Remove the cover.
6. Check for any obvious non-Lenovo alterations. Use good judgment as to the safety of any non-Lenovo
alterations.
7. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or
other liquids, or signs of fire or smoke damage.
8. Check for worn, frayed, or pinched cables.
9. Check that the power-supply cover fasteners (screws or rivets) have not been removed or tampered
with.
http://
Handling devices that are sensitive to electrostatic discharge
Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to
electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects.
Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the
person handling the part are all at the same charge.
Notes:
1. Use product-specific ESD procedures when they exceed the requirements noted here.
2. Make sure that the ESD protective devices you use have been certified (ISO 9000) as fully effective.
When handling ESD-sensitive parts:
• Keep the parts in protective packages until they are inserted into the product.
• Avoid contact with other people.
• Wear a grounded wrist strap against your skin to eliminate static on your body.
• Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when
you are wearing a wrist strap.
• Use a grounded work mat to provide a static-free work surface. The mat is especially useful when
handling ESD-sensitive devices.
• Select a grounding system, such as those listed below, to provide protection that meets the specific
service requirement.
Note: The use of a grounding system to guard against ESD damage is desirable but not necessary.
– Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground.
– When working on a double-insulated or battery-operated system, use an ESD common ground or
reference point. You can use coax or connector-outside shells on these systems.
– Use the round ground prong of the ac plug on ac-operated computers.
Chapter 1. Safety information 3
Page 10
Grounding requirements
Electrical grounding of the computer is required for operator safety and correct system function. Proper
grounding of the electrical outlet can be verified by a certified electrician.
Safety notices (multilingual translations)
The safety notices in this section are provided in the following languages:
• English
• Arabic
• Brazilian Portuguese
• French
• German
• Hebrew
• Japanese
• Korean
• Spanish
• Traditional Chinese
DANGER
DANGER
DANGER
4 Hardware Maintenance Manual
Page 11
DANGER
DANGER
DANGER
DANGER
DANGER
Chapter 1. Safety information 5
Page 12
6 Hardware Maintenance Manual
Page 13
PERIGO
PERIGO
PERIGO
Chapter 1. Safety information 7
Page 14
PERIGO
PERIGO
PERIGO
PERIGO
PERIGO
8
Hardware Maintenance Manual
Page 15
DANGER
DANGER
DANGER
DANGER
Chapter 1. Safety information 9
Page 16
DANGER
DANGER
DANGER
DANGER
VORSICHT
10 Hardware Maintenance Manual
Page 17
VORSICHT
VORSICHT
VORSICHT
VORSICHT
Chapter 1. Safety information 11
Page 18
VORSICHT
VORSICHT
VORSICHT
12 Hardware Maintenance Manual
Page 19
Chapter 1. Safety information 13
Page 20
14 Hardware Maintenance Manual
Page 21
Chapter 1. Safety information 15
Page 22
16 Hardware Maintenance Manual
Page 23
Chapter 1. Safety information 17
Page 24
18 Hardware Maintenance Manual
Page 25
Chapter 1. Safety information 19
Page 26
20 Hardware Maintenance Manual
Page 27
Chapter 2. General checkout
This chapter contains the following topics:
Before you go to the checkout instructions, ensure that you read the following important notes.
Important notes:
• Only certified trained personnel should service the computer.
• Before replacing any FRU, read the entire page on removing and replacing FRUs.
• Be extremely careful during such write operations as copying, saving, or formatting. Drives in the computer
that you are servicing sequence might have been altered. If you select an incorrect drive, data or programs might be
overwritten.
• Replace a FRU only with another FRU of the correct model. When you replace a FRU, make sure that the model
of the machine and the FRU part number are correct by referring to the FRU parts list.
• A FRU should not be replaced because of a single, unreproducible failure. Single failures can occur for a variety
of reasons that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or
software errors. Consider replacing a FRU only when a problem recurs. If you suspect that a FRU is defective, clear
the error log and run the test again. If the error does not recur, do not replace the FRU.
• Be careful not to replace a nondefective FRU.
What to do first
When you return a FRU, you must include the following information in the parts exchange form or parts return
form that you attach to it:
1. Name and phone number of service technician
2. Date of service
3. Date on which the machine failed
4. Date of purchase
5. Failure symptoms, error codes appearing on the display, and beep symptoms
6. Procedure index and page number in which the failing FRU was detected
7. Failing FRU name and part number
8. Machine type, model number, and serial number
9. Customer's name and address
Note: During the warranty period, the customer may be responsible for repair costs if the computer damage
was caused by misuse, accident, modification, unsuitable physical or operating environment, or improper
maintenance by the customer. Following is a list of some common items that are not covered under warranty
and some symptoms that might indicate that the system was subjected to stress beyond normal use.
Before checking problems with the computer, determine whether the damage is covered under the warranty
by referring to the following list:
The following are not covered under warranty:
• LCD panel cracked from the application of excessive force or from being dropped
• Scratched (cosmetic) parts
• Distortion, deformation, or discoloration of the cosmetic parts
• Plastic parts, latches, pins, or connectors that have been cracked or broken by excessive force
• Damage caused by liquid spilled into the system
© Copyright Lenovo 2020 21
Page 28
• Damage caused by the improper insertion of a personal-computer card (PC card) or the installation of an
incompatible card
• Improper disc insertion or use of an external optical drive
• Fuses blown by attachment of a non-supported device
• Forgotten computer password (making the computer unusable)
• Sticky keys caused by spilling a liquid onto the keyboard
• Use of an incorrect ac power adapter on laptop products
The following symptoms might indicate damage caused by non-warranted activities:
• Missing parts might be a symptom of unauthorized service or modification.
• Check for obvious damage to a hard disk drive. If the spindle of a hard disk drive becomes noisy, the hard
disk drive might have been dropped or subject to excessive force.
CRU list
Table 1. Model: Lenovo Ducati 5 (Machine type: 82ES)
CRU
ac power adapter self-service
Power cord self-service
Table 2. Model: IdeaPad 5 14IIL05 (Machine type: 81YH)
CRU
ac power adapter self-service
Power cord self-service
Table 3. Model: IdeaPad 5 14ARE05 (Machine type: 81YM)
CRU Type
ac power adapter self-service
Power cord self-service
Table 4. Model: IdeaPad 5 15IIL05 (Machine type: 81YK)
CRU
ac power adapter self-service
Power cord self-service
Type
Type
Type
Table 5. Model: IdeaPad 5 15ARE 05 (Machine type: 81YQ)
CRU
ac power adapter self-service
Power cord self-service
Type
22 Hardware Maintenance Manual
Page 29
Chapter 3. Idetifying FRUs (CRUs)
Locate FRUs and CRUs
The exploded illustrations help Lenovo service technicians identify FRUs or CRUs that they may need to
replace when servicing a customer’s computer.
© Copyright Lenovo 2020 23
Page 30
Figure 1. IdeaPad 5 (14", 05), IdeaPad Slim 5 (14", 05) and Lenovo Ducati 5 - exploded view
Table 6. FRU (CRU) categories - IdeaPad 5 (14", 05), IdeaPad Slim 5 (14", 05) and Lenovo Ducati 5
No. FRU (CRU) category
1
LCD module
Note: The LCD module as a whole is not a FRU. It contains FRUs as its components.
24 Hardware Maintenance Manual
Page 31
Table 6. FRU (CRU) categories - IdeaPad 5 (14", 05), IdeaPad Slim 5 (14", 05) and Lenovo Ducati 5 (continued)
2
3
4
5
6
7
8
9
a
b
c
Upper case (with keyboard and touch pad)
Fingerprint board
Fan
I/O board with cable
Speaker
Battery pack
Lower case
System board
Power cord
ac power adapter
Screw kit
Figure 2. IdeaPad 5 (14", 05), IdeaPad Slim 5 (14", 05) and Lenovo Ducati 5 LCD module - exploded view
Table 7. FRU categories for the LCD module - IdeaPad 5 (14", 05), IdeaPad Slim 5 (14", 05) and Lenovo Ducati 5
No.
1
2
3
4
5
6
7
8
9
FRU (CRU) category
LCD CAP
LCD bezel
Middle frame
LCD panel
EDP cable
Camera
Camera rubber
Hinge
LCD cover
Chapter 3. Idetifying FRUs (CRUs) 25
Page 32
Figure 3. IdeaPad 5 (15", 05) and IdeaPad Slim 5 (15”, 05) - exploded view
26 Hardware Maintenance Manual
Page 33
Table 8. FRU (CRU) categories - IdeaPad 5 (15”, 05) and IdeaPad Slim 5 (15”, 05)
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
a
FRU (CRU) category
LCD module
Upper case (with keyboard and touch pad)
Speaker
System board
Heat sink
Fan
I/O board with cable
RTC battery
Wi-Fi card
Solid-state drive (SSD) bracket
Solid-state drive (SSD)
Lower case
Battery pack
Hard disk drive bracket
Hard disk drive cable
ac power adapter
b
c
Power cord
Screw kit
Figure 4. IdeaPad 5 (15", 05) and IdeaPad Slim 5 (15”, 05) LCD module - exploded view
Table 9. FRU categories for the LCD module - IdeaPad 5 (15”, 05) and IdeaPad Slim 5 (15”, 05)
No.
1
2
FRU (CRU) category
LCD bezel
Stripe Cover
3
LCD panel
Chapter 3. Idetifying FRUs (CRUs) 27
Page 34
Table 9. FRU categories for the LCD module - IdeaPad 5 (15”, 05) and IdeaPad Slim 5 (15”, 05) (continued)
4
5
6
7
8
Camera board
Microphone rubber
EDP cable
Hinge
LCD cover
28 Hardware Maintenance Manual
Page 35
Chapter 4. Removing a FRU or CRU
Service tools
The following table lists tools for servicing Lenovo computers. Tools with a cross mark are needed for serving
the product models as described by this publication. Prepare them before you service the product.
Table 10. Service tools
Service tool and consumable
Screw driver (Phillips head) (PH1/PH01)
Screw driver (Torx head) (T5) X
Screw driver (Torx head) (T30)
Pry tool 1 X
Tweezers (conductive)
Tweezers (isolated)
Suction cup
Hexagonal socket
Silicone grease
Acetate tape X
Polyamide tape
Mylar tape
Electrical tape
Double-sided tape
Conductive tape
Model applicability
X
X
Eraser
Heat gun
Brown brush
Notes:
• T30 screw drivers are used to service the new Intel Xeon CPUs.
• Hexagonal sockets are used to remove antenna connectors.
• Silicone grease is applied to the CPU and heatsink surfaces to eliminate air gaps.
General guidelines
When removing or replacing a FRU, ensure that you observe the following general guidelines:
1. Do not try to service any computer unless you have been trained and certified. An untrained person runs
the risk of damaging parts.
2. Begin by removing any FRUs that have to be removed before replacing the failing FRU. Any such FRUs
are listed at the beginning of each FRU replacement procedure. Remove them in the order in which they
are listed.
© Copyright Lenovo 2020 29
Page 36
3. Follow the correct sequence in the steps for removing a FRU, as shown in the illustrations by the
numbers in square callouts.
4. When removing a FRU, move it in the direction as shown by the arrow in the illustration.
5. To install a new FRU in place, perform the removal procedure in reverse and follow any notes that
pertain to replacement.
6. When replacing a FRU, carefully retain and reuse all screws.
7. When replacing the base cover, reapply all labels that come with the replacement base cover. If some
original labels are not included with the replacement base cover, peal them off from the original base
cover and paste them on the replacement base cover.
DANGER
Before removing any FRU or CRU, shut down the computer and unplug all power cords from
electrical outlets.
Attention: After replacing a FRU, do not turn on the computer until you have ensured that all screws,
springs, and other small parts are in place and none are loose inside the computer. Verify this by shaking the
computer gently and listening for rattling sounds. Metallic parts or metal flakes can cause electrical short
circuits.
Attention: The system board is sensitive to and can be damaged by ESD. Before touching it, establish
personal grounding by touching a ground point with one hand or by using an ESD strap (P/N 6405959).
Removal procedure for IdeaPad 5 (14", 05), IdeaPad Slim 5 (14", 05) and Lenovo Ducati 5
Remove the lower case
Make sure the computer has been shut down before servicing the computer.
Step 1. Place the computer upside down on a flat surface.
Step 2. Remove nine screws.
Figure 5. Remove nine screws
30 Hardware Maintenance Manual
Page 37
Screw specifications Number of screws
M2 x L3.5 6
M2 x L5.2 + 2.8 3
Step 3. Pry up the latches and then remove the lower case.
Figure 6. Pry up the latches and remove the lower case
Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
Lower case
Remove the battery pack
Make sure the following FRUs (or CRUs) have been removed.
“Remove the lower case” on page 30
Step 1. Disconnect the cable from the system board.
Attention: Use your fingernail to pull the connector to unplug it. Do not pull the cable.
Step 2. Remove two screws and then remove the battery pack.
Figure 7. Remove the battery pack
Chapter 4. Removing a FRU or CRU 31
Page 38
Screw specifications Number of screws
M2 x L3 2
Go to
https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
Battery pack
Remove the solid-state drive module
Make sure the following FRUs (or CRUs) have been removed.
“Remove the lower case” on page 30
Step 1. Disconnect the battery pack cable from the system board.
Attention: Use your fingernail to pull the connector to unplug it. Do not pull the cable.
Step 2. Remove one screw and then remove the solid-state drive module by pulling it away from the slot.
Figure 8. Remove the solid-state drive module
Screw specifications
Number of screws
M2 x L3 1
Step 3. Remove one screw and then separate the solid-state drive and the sollid-state drive bracket.
Figure 9. Separate the solid-state drive and the solid-state drive bracket
Screw specifications
Number of screws
M2 x L2 1
32
Hardware Maintenance Manual
Page 39
Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
Solid-state drive
Solid-state drive bracket
Remove the Wi-Fi card
Make sure the following FRUs (or CRUs) have been removed.
“Remove the lower case” on page 30
Step 1. Disconnect the battery pack cable from the system board.
Attention: Use your fingernail to pull the connector to unplug it. Do not pull the cable.
Step 2. Peel off the insulation film.
Figure 10. Peel off the insulation film
Step 3. Detach the main and auxiliary antenna cable connectors. Remove one screw and then remove the
Wi-Fi card by pulling it away from the slot.
Figure 11. Remove the Wi-Fi card
Screw specifications Number of screws
M2 x L3 1
Go to
https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
Chapter 4. Removing a FRU or CRU 33
Page 40
Wi-Fi card
Remove the heat sink
Make sure the following FRUs (or CRUs) have been removed.
“Remove the lower case” on page 30
Step 1. Disconnect the battery pack cable from the system board.
Attention: Use your fingernail to pull the connector to unplug it. Do not pull the cable.
Step 2. Remove five screws and then remove the heat sink.
Figure 12. Remove five screws and remove the heat sink
Screw specifications
M2 x L3
Go to
https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
Heat sink
Number of screws
5
Remove the fan
Make sure the following FRUs (or CRUs) have been removed.
“Remove the lower case” on page 30
Step 1. Disconnect the battery pack cable from the system board.
Attention: Use your fingernail to pull the connector to unplug it. Do not pull the cable.
Step 2. Disconnect the fan cable from the system board and detach the I/O board cable.
34
Hardware Maintenance Manual
Page 41
Figure 13. Disconnect the fan cable
Step 3. Remove two screws. Release the antennas cable from the cable guide and then remove the fan.
Figure 14. Remove two screws and remove the fan.
Screw specifications Number of screws
M2 x L3 2
Go to
https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement parts:
Fan
Remove the I/O board with cable
Make sure the following FRUs (or CRUs) have been removed.
“Remove the lower case” on page 46
“Remove the battery pack” on page 31
“Remove the fan” on page 34
Step 1. Disconnect the I/O board cable from the system board and then remove three screws.
Chapter 4. Removing a FRU or CRU 35
Page 42
Figure 15. Disconnect cable and remove three screws
Screw specifications
Number of screws
M2.5 x L5.5 2
M2 x L3 1
Step 2. Open the hinge and then remove the I/O board with cable.
Figure 16. Remove the I/O board with cable
Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
I/O board with cable
Remove the speaker
Make sure the following FRUs (CRUs) have been removed.
“Remove the lower case” on page 30
Step 1. Disconnect the battery pack cable from the system board.
Attention: Use your fingernail to pull the connector to unplug it. Do not pull the cable.
Step 2. Disconnect the speaker cable from the system board.
36
Hardware Maintenance Manual
Page 43
Figure 17. Disconnect the cabel from the system board
Step 3. Release the speaker cord and then remove the speaker.
Figure 18. Remove the speaker
Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement parts:
Speaker
Remove the system board
Make sure the following FRUs (or CRUs) have been removed.
“Remove the lower case” on page 30
“Remove the heat sink” on page 34
“Remove the fan” on page 34
“Remove the speaker” on page 36
Step 1. Disconnect cables connected to the system board and then disconnect the antenna cables from
the wireless module.
Chapter 4. Removing a FRU or CRU 37
Page 44
Figure 19. Disconnect cables
Step 2. Remove seven screws.
Figure 20. Remove seven screws
Screw specifications
M2 x L3 3
M2 x L5.5 1
M2.5 x L5.5 3
Step 3. Open the hinge and then remove the system board.
Number of screws
38
Hardware Maintenance Manual
Page 45
Figure 21. Remove the system board
Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
System board
Remove the LCD module
Make sure the following FRUs (CRUs) have been removed.
“Remove the lower case” on page 30
Step 1. Disconnect the battery pack cable from the system board.
Attention: Use your fingernail to pull the connector to unplug it. Do not pull the cable.
Step 2. Detach the antennas cable and disconnect the LCD cable from the system board. Release the
antennas cable from the cable guide.
Figure 22. Disconnect the cables
Step 3. Rotate the LCD module to an angle of more than 90 degrees and place the computer on a flat
surface as shown. Remove five screws.
Chapter 4. Removing a FRU or CRU 39
Page 46
Figure 23. Rotate the LCD module and remove five screws
Screw specifications
M2.5 x L5.5
Number of screws
5
Step 4. Remove the LCD module.
Figure 24. Remove the LCD module
Remove the upper case (with keyboard and touch pad)
Make sure the following FRUs (CRUs) have been removed.
“Remove the lower case” on page 30
“Remove the battery pack” on page 31
“Remove the solid-state drive module” on page 32
“Remove the Wi-Fi card” on page 33
“Remove the heat sink” on page 34
“Remove the fan” on page 34
40
Hardware Maintenance Manual
Page 47
“Remove the I/O board with cable” on page 35
“Remove the speaker” on page 36
“Remove the system board” on page 37
“Remove the LCD module” on page 39
Go to
https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
Upper case (with keyboard and touch pad)
Disassemble the LCD module
The LCD module as a whole is not a FRU. Instead, it contains FRUs as its components. Before
disassembling the LCD module, make sure it has been detached from the upper case.
Remove the LCD CAP
Make sure the following unit have been removed.
“Remove the LCD module” on page 39
Step 1. Slide the LCD CAP to the left carefully and then remove the LCD CAP.
Figure 25. Remove the LCD CAP
Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
LCD CAP
Remove the LCD bezel and the middle frame
Make sure the following FRUs (CRUs) have been removed.
“Remove the LCD CAP” on page 41
Step 1. Remove three screws and then remove the LCD bezel.
Chapter 4. Removing a FRU or CRU 41
Page 48
Figure 26. Remove the LCD bezel
Screw specifications
Number of screws
M1.6 x L4.5 3
Step 2. Remove the middle frame.
Figure 27. Remove the middle frame
Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
LCD bezel
Middle frame
Remove the LCD panel
Make sure the following FRUs (CRUs) have been removed.
“Remove the LCD bezel and the middle frame” on page 41
Step 1. Lift the LCD panel slightly. Disconnect the EDP cable on the back of LCD panel and then remove
the LCD panel.
42
Hardware Maintenance Manual
Page 49
Figure 28. Remove the LCD panel
Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
LCD panel
Remove the EDP cable
Make sure the following FRUs (CRUs) have been removed.
“Remove the LCD panel” on page 42
Step 1. Disconnect the EDP cable from the camera. Peel off the EDP cable from the LCD cover and then
remove the EDP cable.
Figure 29. Remove the EDP cabel
Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
EDP cable
Remove the camera and the camera rubber
Make sure the following FRUs (CRUs) have been removed.
“Remove the LCD panel” on page 42
Step 1. Disconnect the EDP cable from the camera and then remove the camera and the camera rubber.
Chapter 4. Removing a FRU or CRU 43
Page 50
Figure 30. Remove the camera and the camera rubber
Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
Camera
Camera rubber
Remove the hinge
Make sure the following FRUs (CRUs) have been removed.
“Remove the LCD panel” on page 42
Step 1. Remove six screws.
Figure 31. Remove six screws
Screw specifications Number of screws
M2 x L2 6
Step 2. Remove the hinge.
44
Hardware Maintenance Manual
Page 51
Figure 32. Remove the hinge
Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
Hinge
Remove the LCD cover
Make sure the following FRUs (CRUs) have been removed.
“Remove the lower case” on page 30
“Remove the LCD module” on page 39
“Remove the LCD CAP” on page 41
“Remove the LCD bezel and the middle frame” on page 41
“Remove the LCD panel” on page 42
“Remove the EDP cable” on page 43
“Remove the camera and the camera rubber” on page 43
“Remove the hinge” on page 44
Go to
https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
LCD cover
Chapter 4. Removing a FRU or CRU 45
Page 52
Removal procedure for IdeaPad 5 (15”, 05) and IdeaPad Slim 5 (15", 05)
Remove the lower case
Make sure the computer has been shut down before servicing the computer.
Step 1. Place the computer upside down on a flat surface.
Step 2. Remove nine screws.
Figure 33. Remove nine screws
Screw specifications
M2 x L3 6
M2 x L9 3
Step 3. Pry up the latches and then remove the lower case.
Figure 34. Pry up the latches and remove the lower case
Number of screws
Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
46
Hardware Maintenance Manual
Page 53
Lower case
Remove the battery pack
Make sure the following FRUs (or CRUs) have been removed.
“Remove the lower case” on page 46
Step 1. Disconnect the cable from the system board.
Attention: Use your fingernail to pull the connector to unplug it. Do not pull the cable.
Step 2. Remove four screws and then remove the battery pack.
Figure 35. Remove the battery pack
Screw specifications
M2 x L5 4
Go to
https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
Battery pack
Number of screws
Remove the dummy hard disk drive module
Make sure the following FRUs (or CRUs) have been removed.
“Remove the lower case” on page 46
“Remove the battery pack” on page 47
Step 1. Remove the hard disk drive cable from the battery pack.
Figure 36. Remove the hard disk drive cable
Chapter 4. Removing a FRU or CRU 47
Page 54
Step 2. Remove two screws and then remove the hard disk drive bracket.
Figure 37. Remove the hard disk drive bracket
Screw specifications Number of screws
M2 x L5 2
Go to
https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
Hard disk drive cable
Hard disk drive bracket
Remove the solid-state drive
Make sure the following FRUs (or CRUs) have been removed.
“Remove the lower case” on page 46
Step 1. Disconnect the battery pack cable from the system board.
Attention: Use your fingernail to pull the connector to unplug it. Do not pull the cable.
Step 2. Remove one screw and then remove the solid-state drive by pulling it away from the slot.
Figure 38. Remove the solid-state drive
Screw specifications
M2 x L3 1
48
Hardware Maintenance Manual
Number of screws
Page 55
Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
Solid-state drive
Remove the solid-state drive bracket
Make sure the following FRUs (or CRUs) have been removed.
“Remove the lower case” on page 46
“Remove the solid-state drive” on page 48
Step 1. Remove one screw and then remove the solid-state drive bracket.
Figure 39. Remove the solid-state drive bracket
Screw specifications Number of screws
M2 x L3 1
Go to
https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
Solid-state drive bracket
Remove the Wi-Fi card
Make sure the following FRUs (or CRUs) have been removed.
“Remove the lower case” on page 46
Step 1. Disconnect the battery pack cable from the system board.
Attention: Use your fingernail to pull the connector to unplug it. Do not pull the cable.
Step 2. Detach the main and auxiliary antenna cable connectors. Remove one screw and then remove the
wireless module by pulling it away from the slot.
Chapter 4. Removing a FRU or CRU 49
Page 56
Figure 40. Remove the wireless card
Screw specifications
M2 x L3 1
Go to
https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
Wi-Fi card
Number of screws
Remove the RTC battery
Make sure the following FRUs (or CRUs) have been removed.
“Remove the lower case” on page 46
Step 1. Disconnect the RTC battery cable from the I/O board and then remove the RTC battery.
Figure 41. Remove the RTC battery
Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
RTC battery
Remove the I/O board with cable
Make sure the following FRUs (or CRUs) have been removed.
“Remove the lower case” on page 46
“Remove the solid-state drive” on page 48
50
Hardware Maintenance Manual
Page 57
“Remove the solid-state drive bracket” on page 49
Step 1. Disconnect the I/O board cable from the system board and then remove four screws.
Figure 42. Disconnect I/O board cable and remove four screws
Screw specifications
Number of screws
M2.5 x L5 2
M2 x L3 2
Step 2. Open the hinge and then remove the I/O board with cable.
Figure 43. Remove the I/O board with cable
Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
I/O board with cable
Remove the heat sink
Make sure the following FRUs (or CRUs) have been removed.
“Remove the lower case” on page 46
Step 1. Disconnect the battery pack cable from the system board.
Chapter 4. Removing a FRU or CRU 51
Page 58
Attention: Use your fingernail to pull the connector to unplug it. Do not pull the cable.
Step 2. Loosen three screws in alphabetical order and then remove the heat sink.
Figure 44. Loosen three screws and remove the heat sink
Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
Heat sink
Remove the fan
Make sure the following FRUs (or CRUs) have been removed.
“Remove the lower case” on page 46
“Remove the solid-state drive” on page 48
“Remove the solid-state drive bracket” on page 49
Step 1. Disconnect the fan cable from the system board. Release the antennas cable from the cable guide.
Figure 45. Disconnect the fan cable
Step 2. Remove three screws and then remove the fan.
52
Hardware Maintenance Manual
Page 59
Figure 46. Remove three screws and remove the fan
Screw specifications Number of screws
M2 x L3 2
M2 x L5 1
https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
Go to
replacement parts:
Fans
Remove the speaker
Make sure the following FRUs (CRUs) have been removed.
“Remove the lower case” on page 46
“Remove the heat sink” on page 51
Step 1. Disconnect the speaker cable from the system board and then remove the speaker.
Figure 47. Remove the speaker
Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement parts:
Speaker
Remove the system board
Make sure the following FRUs (or CRUs) have been removed.
Chapter 4. Removing a FRU or CRU 53
Page 60
“Remove the lower case” on page 46
“Remove the battery pack” on page 47
“Remove the solid-state drive” on page 48
“Remove the solid-state drive bracket” on page 49
“Remove the heat sink” on page 51
“Remove the fan” on page 52
Step 1. Disconnect the antenna cables from the wireless module. Disconnect cables connected to the
system board.
Figure 48. Disconnect cables
Step 2. Remove six screws and remove the system board.
Figure 49. Remove six screws
Screw specifications Number of screws
M2 x L3 6
Go to
https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
System board
54
Hardware Maintenance Manual
Page 61
Remove the LCD module
Make sure the following FRUs (CRUs) have been removed.
“Remove the lower case” on page 46
Step 1. Disconnect the battery pack cable from the system board.
Attention: Use your fingernail to pull the connector to unplug it. Do not pull the cable.
Step 2. Disconnect the antennas cable and LCD cable from the system board. Release the antennas cable
from the cable guide.
Figure 50. Disconnect the cables
Step 3. Rotate the LCD module to an angle of more than 90 degrees and place the computer on a flat
surface as shown. Remove four screws.
Figure 51. Rotate the LCD module and remove four screws
Screw specifications Number of screws
M2.5 x L5 4
Step 4. Remove the LCD module.
Chapter 4. Removing a FRU or CRU 55
Page 62
Figure 52. Remove the LCD module
Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
LCD module
Remove the upper case (with keyboard and touch pad)
Make sure the following FRUs (CRUs) have been removed.
“Remove the lower case” on page 46
“Remove the battery pack” on page 47
“Remove the dummy hard disk drive module” on page 47
“Remove the solid-state drive” on page 48
“Remove the solid-state drive bracket” on page 49
“Remove the Wi-Fi card” on page 49
“Remove the RTC battery” on page 50
“Remove the I/O board with cable” on page 50
“Remove the heat sink” on page 51
“Remove the fan” on page 52
“Remove the speaker” on page 53
“Remove the system board” on page 53
“Remove the LCD module” on page 55
Go to
https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
Upper case (with keyboard and touch pad)
Disassemble the LCD module
The LCD module as a whole is not a FRU. Instead, it contains FRUs as its components. Before
disassembling the LCD module, make sure it has been detached from the upper case.
56
Hardware Maintenance Manual
Page 63
Remove the LCD bezel
Make sure the following FRUs (CRUs) have been removed.
“Remove the lower case” on page 46
“Remove the LCD module” on page 55
Step 1. Remove the LCD bezel.
Figure 53. Remove the LCD bezel
Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
LCD bezel
Remove the strip covers and the hinges
Make sure the following FRUs (CRUs) have been removed.
“Remove the lower case” on page 46
“Remove the LCD module” on page 55
“Remove the LCD bezel” on page 57
Step 1. Remove the strip covers.
Figure 54. Remove the strip covers
Step 2. Remove six screws and then remove the hinges.
Chapter 4. Removing a FRU or CRU 57
Page 64
Figure 55. Remove six screws and the hinges
Screw specifications
Number of screws
M2 x L3 6
Go to
https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
Strip covers
Hinges
Remove the LCD panel
Make sure the following FRUs (CRUs) have been removed.
“Remove the lower case” on page 46
“Remove the LCD module” on page 55
“Remove the LCD bezel” on page 57
Step 1. Carefully pull out the two pieces of adhesive tape with tweezers.
Figure 56. Remove the adhesive tape
Step 2. Lift the LCD panel slightly. Disconnect the EDP cable and then remove the LCD panel.
58
Hardware Maintenance Manual
Page 65
Figure 57. Disconnect the EDP cable and remove the LCD panel
Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
LCD panel
Remove the EDP cable
Make sure the following FRUs (CRUs) have been removed.
“Remove the lower case” on page 46
“Remove the LCD module” on page 55
“Remove the LCD bezel” on page 57
“Remove the LCD panel” on page 58
Step 1. Disconnnect the EDP cable from the camera board and then peel off the cable from the LCD cover.
Figure 58. Remove the EDP cabel
Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
EDP cable
Remove the camera board
Make sure the following FRUs (CRUs) have been removed.
“Remove the lower case” on page 46
“Remove the LCD module” on page 55
Chapter 4. Removing a FRU or CRU 59
Page 66
“Remove the LCD bezel” on page 57
“Remove the LCD panel” on page 58
Step 1. Disconnnect the EDP cable from the camera board and then remove the camera board and
microphone rubber.
Figure 59. Remove the camera board and microphone rubber
Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
Camera board
Microphone rubber
Remove the LCD cover
Make sure the following FRUs (CRUs) have been removed.
“Remove the lower case” on page 46
“Remove the LCD module” on page 55
“Remove the LCD bezel” on page 57
“Remove the strip covers and the hinges” on page 57
“Remove the LCD panel” on page 58
“Remove the EDP cable” on page 59
“Remove the camera board” on page 59
Go to
https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following
replacement part:
LCD cover
60
Hardware Maintenance Manual
Page 67
Appendix A. Label locations
IdeaPad 5 (14", 05), IdeaPad Slim 5 (14", 05) and Lenovo Ducati 5
Figure 60. Label layout on the back side of the base cover - for WW
Figure 61. Label layout on the back side of the base cover - for CHINA/INDIA
Labels attached to the base cover are country/region specific. Make sure to apply the appropriate labels to
the replacement base cover.
© Copyright Lenovo 2020 61
Page 68
Table 11. All base cover labels
Label Label name
a
b GML label
c
d
e
f
g
h
I
j
Rating label
Adapter label 65 mm x 20 mm
WL/BT label
Country label Argentina label 68 mm x 6 mm
Applied country/region
P.R.China
Label dimensions
76 mm x 24 mm
India
Worldwide 109 mm x 24 mm
All 16 mm x 22.5 mm
Brazil 35 mm x 15 mm
SouthAfrica
Israel/US/CA/TW
Malaysia/Indonesia
20 mm x 10 mm
32 mm x 10 mm
15 mm x 10 mm
Taiwan label 70 mm x 10 mm
Indonesia rating label 26 mm x 10 mm
Vietnam energy label 10 mm x 9 mm
KR/KCC label
India BIS label
50 mm x 43 mm
22 mm x 30 mm
62 Hardware Maintenance Manual
Page 69
Trademarks
LENOVO and the LENOVO logo are trademarks of Lenovo.
All other trademarks are the property of their respective owners. © 2020 Lenovo.
Page 70
Page 71
Page 72
Loading...