Lenovo 8138, 8137, 8123, 8131, 8124 User Manual

Quick Reference

Inside

- Important safety information

- Warranty and other notices

- Computer setup

- Software recovery

- Troubleshooting and diagnostics

- Help and Service

- IBM Lotus software offer

Quick Reference

Note

Before using this information and the product it supports, be sure to read the following:

v “Important safety information” on page v

v Appendix B, “Lenovo Statement of Limited Warranty,” on page 35

v Appendix D, “Notices,” on page 65

First Edition (June 2005)

U.S. GOVERNMENT USERS – RESTRICTED RIGHTS: Our products and/or services are provided with RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to the GSA ADP Schedule contract with Lenovo Group Limited, if any, or the standard terms of this commercial license, or if the agency is unable to accept this Program under these terms, then we provide this Program under the provisions set forth in Commercial Computer Software–Restricted Rights at FA R 52.227-19, when applicable, or under Rights in Data-General, FAR 52.227.14 (Alternate III).

Important safety information . . . . . . . . . . . . . . . .v

Conditions that require immediate action . . . . . . . . . . . . .v

General safety guidelines . . . . . . . . . . . . . . . . . .vi

Additional safety information . . . . . . . . . . . . . . . .xi

Lithium battery notice . . . . . . . . . . . . . . . . . . .xi

Modem safety information . . . . . . . . . . . . . . . . . xii

Laser compliance statement . . . . . . . . . . . . . . . . . xii

Power supply statement . . . . . . . . . . . . . . . . . . xiii

Additional help . . . . . . . . . . . . . . . . . . . . .xv

Chapter 1. Arranging your workspace . . . . . . . . . . . . .1

Comfort . . . . . . . . . . . . . . . . . . . . . . . .1

Chapter 2. Setting up your computer . . . . . . . . . . . . .3

Turning on power . . . . . . . . . . . . . . . . . . . .7

Finishing the software installation . . . . . . . . . . . . . . .7

Completing important tasks . . . . . . . . . . . . . . . . .8

Updating your operating system . . . . . . . . . . . . . . . .8

Installing other operating systems . . . . . . . . . . . . . . .8

Updating your antivirus software . . . . . . . . . . . . . . .8

Starting the Setup Utility . . . . . . . . . . . . . . . . . .9

Shutting down the computer . . . . . . . . . . . . . . . . .9

Recording your computer information . . . . . . . . . . . . . .9

Chapter 3. Recovering software . . . . . . . . . . . . . . .11

Creating and using product recovery discs . . . . . . . . . . . .11

Backup and recovery . . . . . . . . . . . . . . . . . . .12

Using the rescue and recovery workspace . . . . . . . . . . . .13

Solving recovery problems . . . . . . . . . . . . . . . . .15

Creating and using rescue media . . . . . . . . . . . . . . .16

Creating and using a Recovery Repair diskette . . . . . . . . . .16

Recovering or installing device drivers . . . . . . . . . . . . .17

Setting a rescue device in the startup sequence . . . . . . . . . .18

Chapter 4. Getting information, help, and service . . . . . . . . .19

Getting information . . . . . . . . . . . . . . . . . . .19

Getting help and service . . . . . . . . . . . . . . . . . .19

Purchasing additional services . . . . . . . . . . . . . . . .21

Chapter 5. Troubleshooting and diagnostics . . . . . . . . . .23

Basic troubleshooting . . . . . . . . . . . . . . . . . . .23

Power supply and system board Diagnostic LEDs . . . . . . . . .25

PC-Doctor for DOS Diagnostics . . . . . . . . . . . . . . . .25

Error codes . . . . . . . . . . . . . . . . . . . . . .27

POST beep codes . . . . . . . . . . . . . . . . . . . .29

Appendix A. IBM Lotus Software Offer . . . . . . . . . . . .31

Appendix B. Lenovo Statement of Limited Warranty . . . . . . . .35

Part 1 - General Terms . . . . . . . . . . . . . . . . . . .35

Part 2 - Country-unique Terms . . . . . . . . . . . . . . . .39

Part 3 - Warranty Information . . . . . . . . . . . . . . . .52

Guarantee supplement for Mexico . . . . . . . . . . . . . . .61

Appendix C. Customer Replacement Units (CRUs) . . . . . . . .63

Appendix D. Notices . . . . . . . . . . . . . . . . . . .65

Television output notice . . . . . . . . . . . . . . . . . .66

Trademarks . . . . . . . . . . . . . . . . . . . . . .66

Electronic emissions notices . . . . . . . . . . . . . . . . .67

Power cord notice . . . . . . . . . . . . . . . . . . . .70

Polyvinyl Chloride (PVC) cable and cord notice . . . . . . . . . .72

Waste electrical and electronic equipment (WEEE) notice . . . . . . .72

Important safety information

Note

Please read important safety information first.

This information can help you safely use your ThinkCentre

or ThinkPad personal computer. Follow and retain all information included with your computer. The information in this document does not alter the terms of your purchase agreement or the Lenovo

™

Statement of Limited Warranty.

Customer safety is important. Our products are developed to be safe and effective. However, personal computers are electronic devices. Power cords, power adapters, and other features can create potential safety risks that can result in physical injury or property damage, especially if misused. To reduce these risks, follow the instructions included with your product, observe all warnings on the product and in the operating instructions, and review the information included in this document carefully. By carefully following the information contained in this document and provided with your product, you can help protect yourself from hazards and create a safer computer work environment.

Note: This information includes references to power adapters and batteries. In

addition to mobile personal computers, some products (such as speakers and monitors) ship with external power adapters. If you have such a product, this information applies to your product. In addition, your computer product may contain a coin-sized internal battery that provides power to your system clock even when the machine is unplugged, so the battery safety information applies to all computers.

Conditions that require immediate action

Products can become damaged due to misuse or neglect. Some product damage is serious enough that the product should not be used again until it has been inspected and, if necessary, repaired by an authorized servicer.

As with any electronic device, pay close attention to the product when it is turned on. On very rare occasions, you might notice an odor or see a puff of smoke or sparks vent from your machine. Or you might hear sounds like popping, cracking or hissing. These conditions might merely mean that an internal electronic component has failed in a safe and controlled manner. Or, they might indicate a potential safety issue. However, do not take risks or attempt to diagnose the situation yourself.

Frequently inspect your computer and its components for damage or wear or signs of danger. If you have any question about the condition of a component, do not use the product. Contact the Customer Support Center or the product manufacturer for instructions on how to inspect the product and have it repaired, if necessary. For a list of Service and Support phone numbers, see “Worldwide telephone list” on page 57.

In the unlikely event that you notice any of the conditions listed below, or if you have any safety concerns with your product, stop using the product and unplug it from the power source and telecommunication lines until you can speak to the Customer Support Center for further guidance.

v Power cords, plugs, power adapters, extension cords, surge protectors, or

power supplies that are cracked, broken or damaged.

v Signs of overheating, smoke, sparks or fire.

v Damage to a battery (such as cracks, dents, creases), discharge from a

battery, or a buildup of foreign substances on the battery.

v A cracking, hissing or popping sound, or strong odor that comes from the

product.

v Signs that liquid has been spilled or an object has fallen onto the computer

product, the power cord or power adapter.

v The computer product, the power cord or power adapter has been exposed

to water.

v The product has been dropped or damaged in any way.

v The product does not operate normally when you follow the operating

instructions.

If you notice these conditions with a product (such as an extension cord)

Note:

that is not manufactured for or by Lenovo, stop using that product until you can contact the product manufacturer for further instructions, or until you get a suitable replacement.

General safety guidelines

Always observe the following precautions to reduce the risk of injury and property damage.

Service

Do not attempt to service a product yourself unless instructed to do so by the Customer Support Center. Use only a service provider who is approved to repair your particular product.

Note: Some parts can be upgraded or replaced by the customer. These parts

are referred to as Customer Replaceable Units, or CRUs. Lenovo expressly identifies CRUs as such, and provides documentation with

instructions when it is appropriate for customers to replace those parts. You must closely follow all instructions when performing such replacements. Always make sure that the power is turned off and that the product is unplugged from any power source before you attempt the replacement. If you have any questions or concerns, contact the Customer Support Center.

Although there are no moving parts in your computer after the power cord has been disconnected, the following warnings are required for proper UL certification.

Danger

Hazardous moving parts. Keep fingers and other body parts away.

Attention

Before replacing any CRUs, turn off the computer and wait three to five minutes to let the computer cool before opening the cover.

Power cords and power adapters

Use only the power cords and power adapters supplied by the product manufacturer.

Never wrap a power cord around the power adapter or other object. Doing so can stress the cord in ways that can cause the cord to fray, crack or crimp. This can present a safety hazard.

Always route power cords so that they will not be walked on, tripped over, or pinched by objects.

Important safety information vii

Protect the cord and power adapters from liquids. For instance, do not leave your cord or power adapter near sinks, tubs, toilets, or on floors that are cleaned with liquid cleansers. Liquids can cause a short circuit, particularly if the cord or power adapter has been stressed by misuse. Liquids can also cause gradual corrosion of the power cord terminals and/or the connector terminals on the adapter which can eventually result in overheating.

Always connect power cords and signal cables in the correct order and ensure that all power cord connectors are securely and completely plugged into receptacles.

Do not use any power adapter that shows corrosion at the ac input pins and/or shows signs of overheating (such as deformed plastic) at the ac input or anywhere on the power adapter.

Do not use any power cords where the electrical contacts on either end show signs of corrosion or overheating or where the power cord appears to have been damaged in any way.

Extension cords and related devices

Ensure that extension cords, surge protectors, uninterruptible power supplies, and power strips that you use are rated to handle the electrical requirements of the product. Never overload these devices. If power strips are used, the load should not exceed the power strip input rating. Consult an electrician for more information if you have questions about power loads, power requirements, and input ratings.

Plugs and outlets

If a receptacle (power outlet) that you intend to use with your computer equipment appears to be damaged or corroded, do not use the outlet until it is replaced by a qualified electrician.

Do not bend or modify the plug. If the plug is damaged, contact the manufacturer to obtain a replacement.

Some products are equipped with a three-pronged plug. This plug fits only into a grounded electrical outlet. This is a safety feature. Do not defeat this safety feature by trying to insert it into a non-grounded outlet. If you cannot insert the plug into the outlet, contact an electrician for an approved outlet adapter or to replace the outlet with one that enables this safety feature. Never overload an electrical outlet. The overall system load should not exceed 80 percent of the branch circuit rating. Consult an electrician for more information if you have questions about power loads and branch circuit ratings.

viii

Be sure that the power outlet you are using is properly wired, easily accessible, and located close to the equipment. Do not fully extend power cords in a way that will stress the cords.

Carefully connect and disconnect the equipment from the electrical outlet.

Batteries

All personal computers manufactured by Lenovo contain a non-rechargeable coin cell battery to provide power to the system clock. In addition many mobile products such as ThinkPad notebook PCs utilize a rechargeable battery pack to provide system power when in portable mode. Batteries supplied by Lenovo for use with your product have been tested for compatibility and should only be replaced with approved parts.

Never attempt to open or service any battery. Do not crush, puncture, or incinerate batteries or short circuit the metal contacts. Do not expose the battery to water or other liquids. Only recharge the battery pack strictly according to instructions included in the product documentation.

Battery abuse or mishandling can cause the battery to overheat, which can cause gasses or flame to “vent” from the battery pack or coin cell. If your battery is damaged, or if you notice any discharge from your battery or the buildup of foreign materials on the battery leads, stop using the battery and obtain a replacement from the battery manufacturer.

Batteries can degrade when they are left unused for long periods of time. For some rechargeable batteries (particularly Lithium Ion batteries), leaving a battery unused in a discharged state could increase the risk of a battery short circuit, which could shorten the life of the battery and can also pose a safety hazard. Do not let rechargeable Lithium-Ion batteries completely discharge or store these batteries in a discharged state.

Heat and product ventilation

Computers generate heat when turned on and when batteries are charging. Notebook PCs can generate a significant amount of heat due to their compact size. Always follow these basic precautions:

v Do not leave the base of your computer in contact with your lap or any part

of your body for an extended period when the computer is functioning or when the battery is charging. Your computer produces some heat during normal operation. Extended contact with the body could cause discomfort or, potentially, a skin burn.

v Do not operate your computer or charge the battery near flammable

materials or in explosive environments.

v Ventilation slots, fans and/or heat sinks are provided with the product for

safety, comfort, and reliable operation. These features might inadvertently

Important safety information ix

become blocked by placing the product on a bed, sofa, carpet, or other flexible surface. Never block, cover or disable these features.

should inspect your desktop computer for dust accumulation at least once

You every three months. Before inspecting your computer, turn off the power and unplug the computer’s power cord from the electrical outlet; then remove any dust from vents and perforations in the bezel. If you notice external dust accumulation, you should also examine and remove dust from the inside of the computer including heat sink inlet fins, power supply vents, and fans. Always turn off and unplug the computer before opening the cover. If possible, avoid operating your computer within 2 feet of high-traffic areas. If you must operate your computer in or near a high-traffic area, you should inspect and, if necessary, clean your computer more frequently.

For your safety and to maintain optimum computer performance, always follow these basic precautions with your desktop computer:

v Keep the cover closed whenever the computer is plugged in.

v Regularly inspect the outside of the computer for dust accumulation.

v Remove dust from vents and any perforations in the bezel. More frequent

cleanings might be required for computers in dusty or high-traffic areas.

v Do not block or restrict airflow into the front of the computer.

v Do not block the airflow vents on the back of the computer.

v Do not store or operate your computer inside furniture, as this might

increase the risk of overheating.

v Airflow temperatures into the computer should not exceed 35° C (95° F).

v Do not use non-ThinkCentre air filtration devices.

CD and DVD drive safety

CD and DVD drives spin discs at a high speed. If a CD or DVD is cracked or otherwise physically damaged, it is possible for the disc to break apart or even shatter when the CD drive is in use. To protect against possible injury due to this situation, and to reduce the risk of damage to your machine, do the following:

v Always store CD/DVD discs in their original packaging

v Always store CD/DVD discs out of direct sunlight and away from direct

heat sources

v Remove CD/DVD discs from the computer when not in use

v Do not bend or flex CD/DVD discs, or force them into the computer or their

packaging

v Check CD/DVD discs for cracks before each use. Do not use cracked or

damaged discs

Additional safety information

Danger Electrical current from power, telephone, and communication cables is hazardous.

To avoid a shock hazard:

v Do not connect or disconnect any cables or perform installation,

maintenance, or reconfiguration of this product during an electrical storm.

v Connect all power cords to a properly wired and grounded electrical

outlet.

v Connect to properly wired outlets any equipment that will be attached to

this product.

v When possible, use one hand only to connect or disconnect signal cables. v Never turn on any equipment when there is evidence of fire, water, or

structural damage.

v Disconnect the attached power cords, telecommunications systems,

networks, and modems before you open the device covers, unless instructed otherwise in the installation and configuration procedures.

v Connect and disconnect cables as described in the following table when

installing, moving, or opening covers on this product or attached devices.

To connect:

1. Turn everything OFF.

2. First, attach all cables to devices.

3. Attach signal cables to connectors.

4. Attach power cords to outlet.

5. Turn device ON.

To disconnect:

1. Turn everything OFF.

2. First, remove power cords from outlet.

3. Remove signal cables from connectors.

4. Remove all cables from devices.

Lithium battery notice

Caution Danger of explosion if battery is incorrectly replaced.

When replacing the battery, use only Part Number 33F8354 or an equivalent

type battery recommended by the manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of.

Important safety information xi

Do not:

v Throw or immerse into water v Heat to more than 100°C (212°F) v Repair or disassemble

Dispose

of the battery as required by local ordinances or regulations.

Modem safety information

Caution To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.

To reduce the risk of fire, electrical shock, or injury when using telephone

equipment, always follow basic safety precautions, such as:

v Never install telephone wiring during a lightning storm.

v Never install telephone jacks in wet locations unless the jack is specifically

designed for wet locations.

v Never touch uninsulated telephone wires or terminals unless the telephone

line has been disconnected at the network interface.

v Use caution when installing or modifying telephone lines.

v Avoid using a telephone (other than a cordless type) during an electrical

storm. There may be a remote risk of electric shock from lightning.

v Do not use the telephone to report a gas leak in the vicinity of the leak.

Laser compliance statement

Some personal computer models are equipped from the factory with a CD-ROM drive or a DVD-ROM drive. CD-ROM drives and DVD-ROM drives are also sold separately as options. CD-ROM drives and DVD-ROM drives are laser products. These drives are certified in the U.S. to conform to the requirements of the Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J for Class 1 laser products. Elsewhere, these drives are certified to conform to the requirements of the International Electrotechnical Commission (IEC) 825 and CENELEC EN 60 825 for Class 1 laser products.

When a CD-ROM drive or a DVD-ROM drive is installed, note the following handling instructions.

xii

Caution Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure.

Removing the covers of the CD-ROM drive or DVD-ROM drive could result in

exposure to hazardous laser radiation. There are no serviceable parts inside the CD-ROM drive or DVD-ROM drive. Do not remove the drive covers.

Some CD-ROM drives and DVD-ROM drives contain an embedded Class 3A or Class 3B laser diode. Note the following statement.

Danger Laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam.

Power supply statement

Never remove the cover on a power supply or any part that has the following label attached.

Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components. If you suspect a problem with one of these parts, contact a service technician.

Important safety information xiii

xiv

Additional help

This Quick Reference provides the information for installing your computer and starting the operating system. This publication also includes basic troubleshooting information, software recovery procedures, help and service information, and warranty information.

The User Guide for your computer has information about installing optional hardware. This Portable Document Format (PDF) file is available through the Access IBM program on your computer desktop. Use Adobe Acrobat Reader to view your User Guide or print it before installing optional hardware.

The Access IBM program also provides information to help you learn more about the following topics:

v Using your computer

v Installing hardware options

v Connecting communication cables

v Troubleshooting common problems

v Registering your computer

can start the Access IBM program by clicking the icon on your desktop, or

You by clicking Start -> Access IBM.

If you have Internet access, the most current information for your computer is available from the World Wide Web at http://www.lenovo.com/think/support.

You can find the following information on this Web site:

v CRU removal and installation instructions v Publications v Troubleshooting information v Parts information v Downloads and drivers v Links to other useful sources of information v Phone support list

xvi

Chapter 1. Arranging your workspace

To get the most from your computer, arrange both the equipment you use and your work area to suit your needs and the kind of work you do. Your comfort is of foremost importance, but light sources, air circulation, and the location of electrical outlets also can affect the way you arrange your workspace.

Comfort

Although no single working position is ideal for everyone, here are a few guidelines to help you find a position that suits you best.

Sitting in the same position for a long time can cause fatigue. A good chair can make a big difference. The backrest and seat should adjust independently and provide good support. The seat should have a curved front to relieve pressure on the thighs. Adjust the seat so that your thighs are parallel to the floor and your feet are either flat on the floor or on a footrest.

When using the keyboard, keep your forearms parallel to the floor and your wrists in a neutral, comfortable position. Tr y to keep a light touch on the keyboard and your hands and fingers relaxed. Yo u can change the angle of the keyboard for maximum comfort by adjusting the position of the keyboard feet.

Viewing Distance

Lower Back Support

Seat Height

Adjust the monitor so the top of the screen is at, or slightly below, eye level. Place the monitor at a comfortable viewing distance, usually 51 to 61 cm (20 to 24 in.), and position it so you can view it without having to twist your body. Also position other equipment you use regularly, such as the telephone or a mouse, within easy reach.

Glare and lighting

Position the monitor to minimize glare and reflections from overhead lights, windows, and other light sources. Even reflected light from shiny surfaces can cause annoying reflections on your monitor screen. Place the monitor at right

angles to windows and other light sources, when possible. Reduce overhead lighting, if necessary, by turning off lights or using lower wattage bulbs. If you install the monitor near a window, use curtains or blinds to block the sunlight. You might have to adjust the Brightness and Contrast controls on the monitor as the room lighting changes throughout the day.

Where it is impossible to avoid reflections or to adjust the lighting, an antiglare filter placed over the screen might be helpful. However, these filters might affect the clarity of the image on the screen; try them only after you have exhausted other methods of reducing glare.

Dust buildup compounds problems associated with glare. Remember to clean your monitor screen periodically according to your monitor manufacturer’s instructions.

Air circulation

Your computer and monitor produce heat. The computer has a fan that pulls in fresh air and forces out hot air. The monitor lets hot air escape through vents. Blocking the air vents can cause overheating, which might result in a malfunction or damage. Place the computer and monitor so that nothing blocks the air vents; usually, 51 mm (2 in.) of air space is sufficient. Also, make sure the vented air is not blowing on someone else.

Electrical outlets and cable lengths

The location of electrical outlets and the length of power cords and cables that connect to the monitor, printer, and other devices might determine the final placement of your computer.

When arranging your workspace:

v Avoid the use of extension cords. When possible, plug the computer power

cord directly into an electrical outlet.

v Keep power cords and cables neatly routed away from walkways and other

areas where they might get kicked accidentally.

more information about power cords, see “Power cord notice” on page 70

For of this book.

Chapter 2. Setting up your computer

Note: Your computer might not have all of the connectors that are described in

this chapter.

Use the following information when setting up your computer. Look for the small connector icons on the back of your computer.

If your computer cables and connector panel have color-coded connectors, match the color of the cable end with the color of the connector. For example, match a blue cable end with a blue connector, a red cable end with a red connector.

1. Check the position of the voltage-selection switch on the rear of the

computer. Use a ballpoint pen to slide the switch, if necessary.

v If the voltage supply range is 90–137 V ac, set the switch to 115 V.

v If the voltage supply range is 180–265 V ac, set the switch to 230 V.

2. Your keyboard cable might have a standard keyboard connector1 or a Universal Serial Bus (USB) connector2. Connect the keyboard cable to the appropriate keyboard connector.

Note: Some models will have keyboards with a fingerprint reader. See the

Access IBM program for more information.

3. Your mouse cable might have a standard mouse connector1 or a USB connector 2. Connect the mouse cable to the appropriate mouse connector.

4. Connect the monitor cable to the monitor connector on the computer.

v If you have a Standard Video Graphics Array (SVGA) monitor, connect

the cable to the connector as shown.

Note: If your model has two monitor connectors, be sure to use the

connector on the accelerated graphics port (AGP) adapter.

v If you have a digital video interface (DVI) monitor, connect the cable to

the connector as shown.

Note: Your computer must have an adapter installed that supports the

DVI monitor.

5. If you have a modem, connect the modem using the following

instructions.

N O H

PHONE

1 This illustration shows the two connections on the back of the computer to set

PHONE

LINE

up your modem.

2 This illustration shows how modem connections are made in the United States

and other countries or regions that use an RU-11 telephone outlet. Attach one end of the telephone cable to the telephone and the other end to the telephone connector on the back of the computer. Attach one end of the modem cable to the modem connector on the back of the computer and the other end to the telephone outlet.

3 In countries or regions that do not use RU-11 telephone outlets, a splitter or

converter is required to attach the cables to the telephone outlet, as shown at the top of this illustration. Yo u also can use the splitter or converter without the telephone, as shown at the bottom of the illustration.

E IN L

N O H P

LINE

6. If you have audio devices, attach them using the following instructions.

For more information about speakers, see steps 7 and 8.

1 Audio line-in This connector receives audio signals from an external audio

device, such as a stereo system.

2 Audio line-out This connector sends audio signals from the computer to external

devices, such as powered stereo speakers.

3 Microphone Use this connector to attach a microphone to your computer when

you want to record sound or if you use speech-recognition software.

4 Headphone Use this connector to attach headphones to your computer when

you want to listen to music or other sounds without disturbing anyone. This connector might be located on the front of the computer.

7. If you have powered speakers with an ac adapter, use the following

instructions.

a. Connect the cable that runs between the speakers, if necessary. On

some speakers, this cable is permanently attached.

b. Connect the ac adapter cable to the speaker.

c. Connect the speakers to the computer.

d. Connect the ac adapter to the ac power source.

8. If you have unpowered speakers with no ac adapter, use the following

instructions.

a. Connect the cable that runs between the speakers, if necessary. On

some speakers, this cable is permanently attached.

b. Connect the speakers to the computer.

Chapter 2. Setting up your computer 5

9. Connect any additional devices that you have. Your computer might not

have all connectors that are shown.

1394

1 USB Use these connectors to attach a device that requires a Universal

2 Serial Use this connector to attach an external modem, serial printer, or

3 S-video Use this connector to attach a television set that has an S-Video

4 Parallel Use this connector to attach a parallel printer or any other device

5 Ethernet Use this connector to attach the computer to an Ethernet-type local

Serial Bus (USB) connection, such as a mouse, scanner, printer, or personal digital assistant (PDA).

other device that uses a 9-pin serial connector.

connector. This connector is present on some high-performance video adapters.

that requires a 25-pin parallel connection.

area network or to a cable modem.

Important

To operate the computer within FCC limits when it is connected to an Ethernet network, use a Category 5 Ethernet cable.

6 MIDI/joystick Use this connector to attach a joystick, gamepad, or a musical

instrument digital interface (MIDI) device such as a MIDI keyboard.

7 IEEE 1394 This connector is sometimes called Firewire because it transmits

data rapidly. There are two types of IEEE 1394 connectors: the 4-pin and the 6-pin. IEEE 1394 offers connection to several types of consumer electronics, including digital audio devices and scanners.

10. Connect the power cords to properly grounded electrical outlets.

Note: For more information about connectors, see the Access IBM program on

your computer desktop.

Turning on power

Turn on the monitor and other external devices first, and then turn on the computer. When the power-on self-test (POST) is finished, the logo window closes. If your computer has preinstalled software, the software installation program starts.

If you experience any problems during startup, see Chapter 5, “Troubleshooting and diagnostics,” on page 23 and Chapter 4, “Getting information, help, and service,” on page 19.

Finishing the software installation

Important

Read the license agreements carefully before using the programs on this computer. These agreements detail your rights, obligations, and warranties for the software on this computer. By using these programs, you accept the terms of the agreements. If you do not accept the agreements, do not use the programs. Instead, promptly return the entire computer for a full refund.

Note: Some models might have a multilingual version of Microsoft

Windows

XP Pro preinstalled. If your computer has the multilingual version, you will be prompted to choose a language during the initial installation process. After installation, the language version can be changed through the Windows Control Panel.

After you start the computer for the first time, follow the instructions on the screen to complete the software installation. If you do not complete the software installation the first time the computer is turned on, unpredictable results might occur. When the installation is complete, click Access IBM on your desktop to learn more about your computer.

Chapter 2. Setting up your computer 7

Completing important tasks

After you have set up your computer, perform the following tasks, which will save you time and trouble later:

v Create a diagnostics diskette. The diagnostics tool can isolate hardware

problems and is part of the Product Recovery program. Making a diagnostics diskette ahead of time assures you will be able to use of the diagnostics tool if the Product Recovery program becomes inaccessible. See “Creating a Diagnostics diskette” on page 26.

v Record your computer machine type, model, and serial number. If you need

service or technical support, you will probably be asked for this information. See “Recording your computer information” on page 9.

this Quick Reference in a safe place. It is the only publication that has

Keep important information about reinstalling factory-installed software. Chapter 3, “Recovering software,” on page 11 contains the information about recovering factory-installed software.

Updating your operating system

Microsoft makes updates available for various operating systems through the Microsoft Windows Update Web site. The We b site automatically determines what Windows updates are available for your specific computer and lists those updates only. Updates could include security fixes, new versions of Windows components (such as media player), fixes to other portions of the Windows operating system, or enhancements.

For details about updating your operating system, refer to the Access IBM program.

Installing other operating systems

If you install your own operating system, follow the instructions that come with your operating-system CDs or diskettes. Remember to install all device drivers after you install your operating system. Installation instructions are usually provided with the device drivers.

Updating your antivirus software

Your computer comes with the Norton AntiVirus software you can use to detect and eliminate viruses. Yo u should run the LiveUpdate application to get the latest updates from the Norton AntiVirus Web site. LiveUpdate will download the latest virus list and Norton AntiVirus will use the new list when it scans your computer the next time.

For more details about updating your antivirus software, refer to the Access IBM program.

Starting the Setup Utility

The Setup Utility enables you to view, set, or change BIOS configuration settings and passwords.

1. Shut down the operating system and turn off your computer.

2. While turning on your computer, repeatedly press and release the F1 key to

enter the Setup Utility.

Note: If a password has been set, the Setup Utility program menu is not

displayed until you type your password. For more information on the Setup Utility program, see your User Guide.

some cases, the Setup Utility starts automatically when POST detects that

In hardware has been removed from or new hardware has been installed in your computer.

Shutting down the computer

When you are ready to turn off your computer, always follow the shutdown procedure for your operating system. This prevents the loss of unsaved data or damage to your software programs. To shut down the Microsoft Windows operating system select Shut down or Turn off computer from the Start menu.

Recording your computer information

Recording information about your computer can be helpful if you ever need to have your computer serviced. The service technician will probably ask you for this information.

Chapter 2. Setting up your computer 9

The machine type, model, and serial number are labeled on your computer. Use the following table to record this information.

Product name ______________________________________________

Machine type and model ______________________________________________

Serial number (S/N) ______________________________________________

Date of purchase ______________________________________________

You can register your computer over the Internet at the following Web site:

http://www.lenovo.com/register

When you register your computer, you will receive the following benefits:

v Faster service when you call for help

v Automatic notification of free software and special promotional offers

more information about registering your computer, refer to the Access IBM

For program.

Chapter 3. Recovering software

™

The Rescue and Recovery independently of the Windows operating system and is hidden from the Windows operating system. Because the Rescue and Recovery workspace is hidden, it is immune from most virus attacks and provides a safe place to perform rescue and recovery operations that might not be possible in the Windows environment. This chapter will help you become familiar with the following recovery solutions provided by the Rescue and Recovery program installed on your computer:

v Create Product Recovery discs. See ″Creating and using Product Recovery

discs.″

v Create rescue media. See “Creating and using rescue media” on page 16.

v Back up your hard disk periodically. See “Backup and recovery” on page 12.

v Create a Recovery Repair diskette. See “Solving recovery problems” on page

15.

The rescue disc, first disc of the Product Recovery discs and backup

Note:

discs are startable (bootable). They can be started in any type of CD or DVD drive except for a DVD-RAM media.

program provides an environment that runs

If you encounter a problem, you can use the recovery tools from either the Windows environment or from the Rescue and Recovery workspace to do one of the two recovery operations:

v Rescue files

v Restore your backups

“Using the rescue and recovery workspace” on page 13 to perform one of

See the two recovery operations.

See the Access IBM program for additional information about the Rescue and Recovery program.

Creating and using product recovery discs

If your computer is equipped with a recordable CD or DVD drive, you can create a set of Product Recovery discs that enables you to restore the contents of the hard disk to the same state as when the computer was originally shipped from the factory. Product Recovery discs are useful if you transfer the computer to another area, sell the computer, recycle the computer, or as a last resort put the computer in an operational state after all other methods of recovery have failed. It is a good idea to create a set of Product Recovery discs as soon as possible.

+ 65 hidden pages

Lenovo 8138, 8137, 8123, 8131, 8124 User Manual

Contents

Important safety information

Conditions that require immediate action

General safety guidelines

Service

Power cords and power adapters

Extension cords and related devices

Plugs and outlets

Batteries

Heat and product ventilation

CD and DVD drive safety

Additional safety information

Lithium battery notice

Modem safety information

Laser compliance statement

Power supply statement

Additional help

Chapter 1. Arranging your workspace

Comfort

Glare and lighting

Air circulation

Electrical outlets and cable lengths

Chapter 2. Setting up your computer

Turning on power

Finishing the software installation

Completing important tasks

Updating your operating system

Installing other operating systems

Updating your antivirus software

Starting the Setup Utility

Shutting down the computer

Recording your computer information

Chapter 3. Recovering software

Creating and using product recovery discs