Lenovo 30CY000RUK User Manual
P330 User Guide
Machine Types (2nd Gen): 30CY, 30D0, and 30D3
Note: Before using this information and the product it supports, be sure to read and understand the “Read
this first: Important safety information” on page iii and Appendix G “Notices” on page 131.
First Edition (August 2018)
© Copyright Lenovo 2018.
LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant to a General Services
Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS35F-05925.
Contents
Read this first: Important safety
information . . . . . . . . . . . . . . . . iii
Before using this manual . . . . . . . . . . . . iii
Service and upgrades . . . . . . . . . . . . . iii
Static electricity prevention . . . . . . . . . . . iv
Power cords and power adapters . . . . . . . . . iv
Extension cords and related devices. . . . . . . . v
Plugs and outlets . . . . . . . . . . . . . . . v
External devices . . . . . . . . . . . . . . . v
Heat and product ventilation . . . . . . . . . . . v
Computer placement notices . . . . . . . . . . vi
Operating environment . . . . . . . . . . . . . vi
Laser compliance statement . . . . . . . . . . . vii
Hazardous energy statement . . . . . . . . . . vii
Lithium coin-cell battery notice . . . . . . . . . . vii
Using earphones, headphones, or a headset . . . viii
Cleaning and maintenance . . . . . . . . . . . ix
Chapter 1. Product overview . . . . . . 1
Hardware locations . . . . . . . . . . . . . . 1
Front view . . . . . . . . . . . . . . . . 1
Rear view . . . . . . . . . . . . . . . . 3
Computer components . . . . . . . . . . . 5
Parts on the system board . . . . . . . . . . 6
Internal storage drives . . . . . . . . . . . 8
Machine type and model label . . . . . . . . 9
Computer features. . . . . . . . . . . . . . 10
Computer specifications . . . . . . . . . . . 13
Programs . . . . . . . . . . . . . . . . . 14
Accessing a program on your computer . . . 14
An introduction to Lenovo programs . . . . . 14
Chapter 2. Using your computer . . . 17
Registering your computer . . . . . . . . . . 17
Setting the computer volume . . . . . . . . . 17
Using a disc . . . . . . . . . . . . . . . . 17
Guidelines about using the optical drive . . . 17
Handling and storing a disc . . . . . . . . 17
Playing and removing a disc . . . . . . . . 18
Recording a disc . . . . . . . . . . . . 18
Connecting to a network . . . . . . . . . . . 19
Chapter 3. You and your computer . . 21
Arranging your workspace . . . . . . . . . . 21
Glare and lighting . . . . . . . . . . . . 21
Air circulation . . . . . . . . . . . . . . 21
Electrical outlet locations and cable lengths . . 21
Comfort . . . . . . . . . . . . . . . . 21
Accessibility information . . . . . . . . . . . 22
Cleaning your computer . . . . . . . . . . . 25
Maintenance . . . . . . . . . . . . . . . . 25
Basic maintenance tips . . . . . . . . . . 25
Good maintenance practices. . . . . . . . 25
Keeping your computer current . . . . . . . 26
Moving your computer . . . . . . . . . . . . 26
Chapter 4. Security . . . . . . . . . . 27
Locking your computer . . . . . . . . . . . . 27
Enabling or disabling the E-lock. . . . . . . 27
Locking the computer cover . . . . . . . . 27
Attaching a Kensington-style cable lock . . . 29
Attaching a cable lock . . . . . . . . . . 29
Viewing and changing security settings in the
Setup Utility program . . . . . . . . . . . . 30
Using passwords and Windows accounts . . . . 30
Using the cover presence switch . . . . . . . . 31
Using firewalls . . . . . . . . . . . . . . . 31
Protecting data against viruses . . . . . . . . . 31
Using the Smart USB Protection function. . . . . 32
Computrace Agent software embedded in
firmware. . . . . . . . . . . . . . . . . . 32
Trusted Platform Module (TPM). . . . . . . . . 32
Chapter 5. Advanced
configuration . . . . . . . . . . . . . . 33
Using the Setup Utility program . . . . . . . . 33
Starting the Setup Utility program . . . . . . 33
Changing the display language of the Setup
Utility program . . . . . . . . . . . . . 33
Enabling or disabling a device . . . . . . . 33
Enabling or disabling the automatic power-on
of your computer . . . . . . . . . . . . 34
Enabling or disabling the ErP LPS compliance
mode . . . . . . . . . . . . . . . . . 34
Enabling or disabling the eSATA mode for the
SATA 4 connector . . . . . . . . . . . . 34
Switching between better acoustic and better
thermal performance . . . . . . . . . . . 35
Enabling or disabling the system to record
thermal alert logs . . . . . . . . . . . . 35
Enabling or disabling the configuration change
detection . . . . . . . . . . . . . . . 35
Changing the BIOS settings before installing a
new operating system . . . . . . . . . . 36
Using BIOS passwords . . . . . . . . . . 36
Selecting a startup device . . . . . . . . . 38
Exiting the Setup Utility program . . . . . . 39
Updating and recovering the BIOS . . . . . . . 39
© Copyright Lenovo 2018 i
Configuring RAID . . . . . . . . . . . . . . 40
An Introduction to RAID . . . . . . . . . . 40
RAID Level . . . . . . . . . . . . . . . 40
Configuring the system BIOS to enable SATA
RAID functionality . . . . . . . . . . . . 40
Configuring RAID in UEFI mode. . . . . . . 41
Configuring RAID in legacy mode . . . . . . 41
Cover presence switch . . . . . . . . . . 88
Power supply assembly . . . . . . . . . . 90
Storage drive in the storage-drive bay . . . . 91
Type-1 storage-drive cage. . . . . . . . . 97
Type-2 storage-drive cage. . . . . . . . . 104
Heat-sink-and-fan assembly . . . . . . . . 106
Completing the parts replacement . . . . . . . 108
Chapter 6. Troubleshooting,
diagnostics, and recovery . . . . . . . 43
Basic procedure for resolving computer
problems . . . . . . . . . . . . . . . . . 43
Troubleshooting . . . . . . . . . . . . . . 43
Startup problems . . . . . . . . . . . . 43
Audio problems . . . . . . . . . . . . . 44
CD or DVD problems . . . . . . . . . . . 45
Intermittent problems. . . . . . . . . . . 46
Storage drive problems . . . . . . . . . . 46
Ethernet LAN problems . . . . . . . . . . 46
Wireless LAN problem . . . . . . . . . . 47
Bluetooth problems . . . . . . . . . . . 48
Performance problems . . . . . . . . . . 48
Serial connector problem . . . . . . . . . 49
USB device problems . . . . . . . . . . 50
Software and driver problems . . . . . . . 50
Diagnosing problems . . . . . . . . . . . . 51
Recovery information . . . . . . . . . . . . 51
Chapter 7. Hardware removal and
installation . . . . . . . . . . . . . . . 53
Handling static-sensitive devices . . . . . . . . 53
Customer Replaceable Units. . . . . . . . . . 53
Preparing your computer . . . . . . . . . . . 54
Removing and installing hardware . . . . . . . 57
External options . . . . . . . . . . . . . 57
Slim optical drive . . . . . . . . . . . . 57
PCIe card . . . . . . . . . . . . . . . 59
Full-length PCIe card . . . . . . . . . . . 61
M.2 solid-state drive . . . . . . . . . . . 65
Memory module . . . . . . . . . . . . . 71
Device in the flex bay . . . . . . . . . . . 73
Storage drive in the front-access storage
enclosure . . . . . . . . . . . . . . . 76
Device in the flex storage enclosure . . . . . 81
Coin-cell battery. . . . . . . . . . . . . 87
Chapter 8. Getting information, help,
and service . . . . . . . . . . . . . . . 111
Information resources . . . . . . . . . . . . 111
Accessing the user guide in various
languages . . . . . . . . . . . . . . . 111
Windows help system . . . . . . . . . . 111
Safety and warranty . . . . . . . . . . . 111
Lenovo Web site. . . . . . . . . . . . . 111
Lenovo Support Web site . . . . . . . . . 111
Help and service . . . . . . . . . . . . . . 112
Calling for service . . . . . . . . . . . . 112
Using other services . . . . . . . . . . . 112
Purchasing additional services . . . . . . . 113
Appendix A. System memory
speed. . . . . . . . . . . . . . . . . . 115
Appendix B. Supplemental
information about the Ubuntu operating
system . . . . . . . . . . . . . . . . . 117
Appendix C. Regulatory
information . . . . . . . . . . . . . . . 119
Appendix D. WEEE and recycling
information of countries and
regions . . . . . . . . . . . . . . . . . 123
Appendix E. Restriction of
Hazardous Substances (RoHS) Directive
of countries and regions . . . . . . . . 127
Appendix F. ENERGY STAR model
information . . . . . . . . . . . . . . . 129
Appendix G. Notices. . . . . . . . . . 131
Appendix H. Trademarks . . . . . . . 133
ii P330 User Guide
Read this first: Important safety information
This chapter contains the safety information that you must be familiar with.
Before using this manual
CAUTION:
Before using this manual, be sure to read and understand all the related safety information for this
product. Refer to the information in this section and the safety information in the Safety and Warranty
Guide that you received with this product. Reading and understanding this safety information reduces
the risk of personal injury and damage to your product.
If you no longer have a copy of the Safety and Warranty Guide, you can obtain a Portable Document Format
(PDF) version from the Lenovo Support Web site at
also provides the Safety and Warranty Guide and this User Guide in additional languages.
Service and upgrades
Do not attempt to service a product yourself unless instructed to do so by the Customer Support Center or
your documentation. Only use a Service Provider who is approved to repair your particular product.
Note: Some computer parts can be upgraded or replaced by the customer. Upgrades typically are referred
to as options. Replacement parts approved for customer installation are referred to as Customer
Replaceable Units, or CRUs. Lenovo provides documentation with instructions when it is appropriate for
customers to install options or replace CRUs. You must closely follow all instructions when installing or
replacing parts. The Off state of a power indicator does not necessarily mean that voltage levels inside a
product are zero. Before you remove the covers from a product equipped with a power cord, always ensure
that the power is turned off and that the product is unplugged from any power source. For more information
about CRUs, refer to Chapter 7 “Hardware removal and installation” on page 53. If you have any questions or
concerns, contact the Customer Support Center.
https://support.lenovo.com. The Lenovo Support Web site
Although there are no moving parts in your computer after the power cord has been disconnected, the
following warnings are required for your safety.
CAUTION:
Keep fingers and other parts of your body away from hazardous, moving parts. If you suffer an injury,
seek medical care immediately.
CAUTION:
Avoid contact with hot components inside the computer. During operation, some components
become hot enough to burn the skin. Before you open the computer cover, turn off the computer,
disconnect power, and wait approximately 10 minutes for the components to cool.
CAUTION:
After replacing a CRU, reinstall all protective covers, including the computer cover, before connecting
power and operating the computer. This action is important to help prevent unexpected electrical
shock and help ensure the containment of an unexpected fire that could happen under extremely rare
conditions.
CAUTION:
© Copyright Lenovo 2018 iii
When replacing CRUs, be cautious of sharp edges or corners that might cause injury. If you suffer an
injury, seek medical care immediately.
Static electricity prevention
Static electricity, although harmless to you, can seriously damage computer components and options.
Improper handling of static-sensitive parts can damage the part. When you unpack an option or CRU, do not
open the static-protective package containing the part until the instructions direct you to install it.
When you handle options or CRUs, or perform any work inside the computer, take the following precautions
to avoid static-electricity damage:
• Limit your movement. Movement can cause static electricity to build up around you.
• Always handle components carefully. Handle adapters, memory modules, and other circuit boards by the
edges. Never touch exposed circuitry.
• Prevent others from touching components.
• When you install a static-sensitive option or CRU, touch the static-protective package containing the part
to a metal expansion-slot cover or other unpainted metal surface on the computer for at least two
seconds. This reduces static electricity in the package and your body.
• When possible, remove the static-sensitive part from the static-protective packaging and install the part
without setting it down. When this is not possible, place the static-protective packaging on a smooth, level
surface and place the part on it.
• Do not place the part on the computer cover or other metal surface.
Power cords and power adapters
Use only the power cords and power adapters supplied by the product manufacturer. Do not use the ac
power cord for other devices.
The power cords shall be safety approved. For Germany, it shall be H05VV-F, 3G, 0.75 mm
other countries, the suitable types shall be used accordingly.
Never wrap a power cord around a power adapter or other object. Doing so can stress the cord in ways that
can cause the cord to fray, crack, or crimp. This can present a safety hazard.
Always route power cords so that they will not be walked on, tripped over, or pinched by objects.
Protect power cord and power adapters from liquids. For instance, do not leave your power cord or power
adapter near sinks, tubs, toilets, or on floors that are cleaned with liquid cleansers. Liquids can cause a short
circuit, particularly if the power cord or power adapter has been stressed by misuse. Liquids also can cause
gradual corrosion of power cord terminals and/or the connector terminals on a power adapter, which can
eventually result in overheating.
Ensure that all power cord connectors are securely and completely plugged into receptacles.
Do not use any power adapter that shows corrosion at the ac input pins or shows signs of overheating (such
as deformed plastic) at the ac input or anywhere on the power adapter.
Do not use any power cords where the electrical contacts on either end show signs of corrosion or
overheating or where the power cord appears to have been damaged in any way.
2
, or better. For
iv
P330 User Guide
Extension cords and related devices
Ensure that extension cords, surge protectors, uninterruptible power supplies, and power strips that you use
are rated to handle the electrical requirements of the product. Never overload these devices. If power strips
are used, the load should not exceed the power strip input rating. Consult an electrician for more information
if you have questions about power loads, power requirements, and input ratings.
Plugs and outlets
If a receptacle (power outlet) that you intend to use with your computer equipment appears to be damaged
or corroded, do not use the outlet until it is replaced by a qualified electrician.
Do not bend or modify the plug. If the plug is damaged, contact the manufacturer to obtain a replacement.
Do not share an electrical outlet with other home or commercial appliances that draw large amounts of
electricity. Otherwise, unstable voltage might damage your computer, data, or connected devices.
Some products are equipped with a three-pronged plug. This plug fits only into a grounded electrical outlet.
This is a safety feature. Do not defeat this safety feature by trying to insert it into a non-grounded outlet. If
you cannot insert the plug into the outlet, contact an electrician for an approved outlet adapter or to replace
the outlet with one that enables this safety feature. Never overload an electrical outlet. The overall system
load should not exceed 80 percent of the branch circuit rating. Consult an electrician for more information if
you have questions about power loads and branch circuit ratings.
Be sure that the power outlet you are using is properly wired, easily accessible, and located close to the
equipment. Do not fully extend power cords in a way that will stress the cords.
Be sure that the power outlet provides the correct voltage and current for the product you are installing.
Carefully connect and disconnect the equipment from the electrical outlet.
External devices
Do not connect or disconnect any external device cables other than Universal Serial Bus (USB) cables while
the computer power is on; otherwise, you might damage your computer. To avoid possible damage to
connected devices, wait at least five seconds after the computer is shut down to disconnect external
devices.
Heat and product ventilation
Computers, power adapters, and many accessories can generate heat when turned on and when batteries
are charging. Always follow these basic precautions:
• Do not leave your computer, power adapter, or accessories in contact with your lap or any part of your
body for an extended period when the products are functioning or when the battery is charging. Your
computer, power adapter, and many accessories produce some heat during normal operation. Extended
contact with the body could cause discomfort or, potentially, a skin burn.
© Copyright Lenovo 2018 v
• Do not charge the battery or operate your computer, power adapter, or accessories near flammable
materials or in explosive environments.
• Ventilation slots, fans, and heat sinks are provided with the product for safety, comfort, and reliable
operation. These features might inadvertently become blocked by placing the product on a bed, sofa,
carpet, or other flexible surface. Never block, cover, or disable these features.
Inspect your desktop computer for dust accumulation at least once every three months. Before inspecting
your computer, turn off the power and unplug the computer's power cord from the electrical outlet; then
remove any dust from vents and perforations in the bezel. If you notice external dust accumulation, then
examine and remove dust from the inside of the computer including heat sink inlet fins, power supply vents,
and fans. Always turn off and unplug the computer before opening the cover. If possible, avoid operating
your computer within two feet of high-traffic areas. If you must operate your computer in or near a high-traffic
area, inspect and, if necessary, clean your computer more frequently.
For your safety and to maintain optimum computer performance, always follow these basic precautions with
your desktop computer:
• Keep the cover closed whenever the computer is plugged in.
• Regularly inspect the outside of the computer for dust accumulation.
• Remove dust from vents and any perforations in the bezel. More frequent cleanings might be required for
computers in dusty or high-traffic areas.
• Do not restrict or block any ventilation openings.
• Do not store or operate your computer inside furniture, as this might increase the risk of overheating.
• Airflow temperatures into the computer should not exceed 35°C (95°F).
• Do not install air filtration devices. They may interfere with proper cooling.
Computer placement notices
Inappropriate computer placement might cause harm to children.
• Place the computer on a sturdy piece of low-rise furniture or furniture that has been anchored.
• Do not place the computer at the edge of the furniture.
• Keep the computer cables out of the reach of children.
• Some items, such as toys, might attract children. Keep such items away from the computer.
Supervise children in rooms where the above safety instructions cannot be fully implemented.
Operating environment
The optimal environment in which to use your computer is 10°C–35°C (50°F–95°F) with humidity ranging
between 35% and 80%. If your computer is stored or transported in temperatures less than 10°C (50°F),
allow the cold computer to rise slowly to an optimal operating temperature of 10°C–35°C (50°F–95°F) before
use. This process could take two hours in extreme conditions. Failure to allow your computer to rise to an
optimal operating temperature before use could result in irreparable damage to your computer.
If possible, place your computer in a well-ventilated and dry area without direct exposure to sunshine.
Keep electrical appliances such as an electric fan, radio, high-powered speakers, air conditioner, and
microwave oven away from your computer because the strong magnetic fields generated by these
appliances can damage the monitor and data on the storage drive.
vi
P330 User Guide
Do not place any beverages on top of or beside the computer or other connected devices. If liquid is spilled
on or in the computer or a connected device, a short circuit or other damage might occur.
Do not eat or smoke over your keyboard. Particles that fall into your keyboard can cause damage.
Laser compliance statement
CAUTION:
When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are
installed, note the following:
• Do not remove the covers. Removing the covers of the laser product could result in exposure to
hazardous laser radiation. There are no serviceable parts inside the device.
• Use of controls or adjustments or performance of procedures other than those specified herein
might result in hazardous radiation exposure.
DANGER
Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following:
Laser radiation when open. Do not stare into the beam, do not view directly with optical
instruments, and avoid direct exposure to the beam.
Hazardous energy statement
DANGER
Disconnect all power cords from electrical outlets before removing the computer cover or any part
that has the above label attached.
DO NOT disassemble components that have the above label attached. There are no serviceable parts inside
these components.
Your product is designed for safe use. However, hazardous voltage, current, and energy levels are present
inside any component that has this label attached. Disassembling of these components might cause fire or
might even result in death. If you suspect a problem with one of these parts, contact a service technician.
Lithium coin-cell battery notice
DANGER
Danger of explosion if battery is incorrectly replaced.
© Copyright Lenovo 2018 vii
When replacing the lithium coin-cell battery, use only the same type or equivalent type that is recommended
by the manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed
of. Swallowing the lithium coin-cell battery will cause chocking or severe internal burns in just two hours and
might even result in death.
Keep batteries away from children. If the lithium coin-cell battery is swallowed or placed inside any part of
the body, seek medical care immediately.
Do not:
• Throw or immerse into water
• Heat to more than 100 °C (212°F).
• Repair or disassemble
• Leave in an extremely low air pressure environment
• Leave in an extremely high-temperature environment
• Crush, puncture, cut, or incinerate
Dispose of the battery as required by local ordinances or regulations.
The following statement applies to users in the state of California, U.S.A.
California Perchlorate Information:
Products containing manganese dioxide lithium coin-cell batteries may contain perchlorate.
Perchlorate Material - special handling may apply, see
perchlorate/
.
https://www.dtsc.ca.gov/hazardouswaste/
Using earphones, headphones, or a headset
• If your computer has both a headphone connector and an audio line-out connector, always use the
headphone connector for earphones, headphones, or a headset. However, the headphone connector
does not support the microphone of the headset.
• If your computer has both a headset connector and an audio line-out connector, always use the headset
connector for earphones, headphones, or a headset.
CAUTION:
Excessive sound pressure from earphones and headphones can cause hearing loss. Adjustment of
the equalizer to maximum increases the earphone and headphone output voltage and the sound
pressure level. Therefore, to protect your hearing, adjust the equalizer to an appropriate level.
Excessive use of headphones or earphones for a long period of time at high volume can be dangerous if the
output of the headphone or earphone connectors do not comply with specifications of EN 50332-2. The
headphone output connector of your computer complies with EN 50332-2 Sub clause 7. This specification
limits the computer’s maximum wide band true RMS output voltage to 150 mV. To help protect against
hearing loss, ensure that the headphones or earphones you use also comply with EN 50332-2 (Clause 7
Limits) or a wide band characteristic voltage of 75 mV. Using headphones that do not comply with EN 503322 can be dangerous due to excessive sound pressure levels.
If your Lenovo computer came with headphones or earphones in the package, as a set, the combination of
the headphones or earphones and the computer already complies with the specifications of EN 50332-1. If
different headphones or earphones are used, ensure that they comply with EN 50332-1 (Clause 6.5
Limitation Values). Using headphones that do not comply with EN 50332-1 can be dangerous due to
excessive sound pressure levels.
viii
P330 User Guide
Cleaning and maintenance
Keep your computer and workspace clean. Shut down the computer and then disconnect the power cord
before cleaning the computer. Do not spray any liquid detergent directly on the computer or use any
detergent containing flammable material to clean the computer. Spray the detergent on a soft cloth and then
wipe the computer surfaces.
© Copyright Lenovo 2018 ix
x P330 User Guide
Chapter 1. Product overview
This chapter provides basic information to help you get familiar with your computer.
Hardware locations
This section provides information about the locations of your computer hardware.
Front view
Note: The computer hardware might look slightly different from the illustration.
Figure 1. Front connectors, controls, and indicators
1 Power button 2 Power indicator
3 Storage-drive activity indicator 4 SD card slot (available on some models)
5 Microphone connector 6 Headset connector
7 USB-C connector 8 USB 3.1 connectors Gen 1 (2)
9 USB 3.1 connectors Gen 2 (2) 10 Slim optical-drive eject button (available on some
models)
11 Flex bay (available on some models)
1 Power button
Press the power button to turn on your computer. If your computer is unresponsive, you can turn off the
computer by pressing and holding the power button for four or more seconds.
© Copyright Lenovo 2018 1
2 Power indicator
When the power indicator is on, the computer is turned on.
3 Storage-drive activity indicator
This indicator shows the status of the internal storage drives (such as hard disk drives or solid-state drives).
On: The storage drives are active and data is being transferred.
Off (when the computer is powered on): The storage drives are not in use or no data is being transferred.
4 SD card slot (available on some models)
An SD card is installed on some computer models.
5 Microphone connector
Use this connector to attach a microphone to your computer when you want to record sound or if you use
speech-recognition software.
6 Headset connector
Use this connector to attach a headset to your computer.
7 USB-C connector
The USB-C connector supports the USB Type-C™ standard. With an appropriate USB-C cable connected,
you can use the connector to transfer data or charge your device.
8 USB 3.1 connectors Gen 1 (2)
Connect USB-compatible devices, such as a USB keyboard, a USB mouse, a USB storage device, or a USB
printer.
9 USB 3.1 connectors Gen 2 (2)
With greater data transfer rate, the USB 3.1 connector Gen 2 is used to connect USB-compatible devices,
such as a USB keyboard, a USB mouse, a USB storage device, or a USB printer.
10 Slim optical-drive eject button (available on some models)
Press the button to eject the tray of the slim optical drive. To close the tray, push the tray inward until you
hear a click.
11 Flex bay (available on some models)
Some computer models come with a flex bay. Depending on your computer model, one of the following
devices might be installed in the flex bay:
• Flex module
• Flex storage enclosure
• Front-access storage enclosure
For more information, see “Device in the flex bay” on page 73.
2
P330 User Guide
Rear view
7
8
5
6
Some connectors on the rear of your computer are color-coded to help you determine where to connect the
cables on your computer.
Note: The computer hardware might look slightly different from the illustration.
Figure 2. Rear view
1 Audio line-out connector
3 DisplayPort connectors (2) 4 DisplayPort connector or HDMI™ connector (available
2 Serial connector
on some models)
5 USB 3.1 connector Gen 1 6 USB 3.1 connector Gen 1
7 USB 2.0 connectors (2)
9 PCIe card area*
11 Security-lock slot 12 Cable-lock slots
13 Padlock loop
15 PS/2 keyboard connector (available on some models) 16 PS/2 mouse connector (available on some models)
8 Ethernet connector
10 Power-cord connector
14 Serial connector (available on some models)
Notes: * A discrete graphics card or a network adapter can be installed in the appropriate Peripheral
Component Interconnect Express (PCIe) card slot. If such a card is installed, use the connectors on the card
instead of the corresponding connectors on the computer to optimize the performance. Depending on your
computer model, the preinstalled cards might vary. One or more graphics cards might be installed to provide
the following connectors:
• Digital Visual Interface (DVI) connector
• DisplayPort
• Mini DisplayPort
®
connector
®
connector
DVI monitor connector
Chapter 1. Product overview 3
Use this connector to attach a DVI monitor or other compatible devices.
DisplayPort connector
Use this connector to attach a high-performance monitor, a direct-drive monitor, or other compatible
devices.
Mini DisplayPort connector
Use this connector to attach a high-performance monitor, a direct-drive monitor, or other compatible
devices. The Mini DisplayPort connector is a miniaturized version of a DisplayPort connector.
1 Audio line-out connector
The audio line-out connector is used to send audio signals from the computer to external devices, such as
headphones.
2 Serial connector
Use this connector to attach an external modem, a serial printer, or other devices that use a 9-pin serial
connector.
3 DisplayPort connectors (2)
Use this connector to attach a high-performance monitor, a direct-drive monitor, or other compatible
devices.
4 DisplayPort connector or HDMI connector (available on some models)
• DisplayPort connector
Use this connector to attach a high-performance monitor, a direct-drive monitor, or other compatible
devices.
• HDMI connector
The High-Definition Multimedia Interface (HDMI) connector is a digital audio and video interface that can
connect a compatible digital audio device or video monitor, such as a DVD player or a high-definition
digital television (HDTV).
5 USB 3.1 connector Gen 1
Connect USB-compatible devices, such as a USB keyboard, a USB mouse, a USB storage device, or a USB
printer. This connector supports the smart power on feature. When you connect a supported keyboard to
this connector, you can turn on the computer or wake it up from hibernation mode by pressing Alt+P on the
keyboard. You can enable or disable the smart power on feature from the Setup Utility program.
6 USB 3.1 connector Gen 1
Connect USB-compatible devices, such as a USB keyboard, a USB mouse, a USB storage device, or a USB
printer.
7 USB 2.0 connectors (2)
Use this connector to attach a USB-compatible device, such as a USB keyboard, mouse, storage drive, or
printer.
8 Ethernet connector
4
P330 User Guide
Connect an Ethernet cable for a local area network (LAN).
Note: To operate the computer within Federal Communications Commission (FCC) Class B limits, use a
Category 5 Ethernet cable.
9 PCIe card area
To further improve the computer performance, you can install PCIe cards into this area. Depending on your
computer model, the preinstalled cards might vary.
10 Power-cord connector
Connect the power cord to your computer for power supply.
11 Security-lock slot
Attach a Kensington-style cable lock to the security-lock slot to secure your computer. For more information,
see “Attaching a Kensington-style cable lock” on page 29.
12 Cable lock slots
Used to secure a cable lock. For more information, see “Attaching a cable lock” on page 29.
13 Padlock loop
Connect a padlock to secure your computer. For more information, see “Locking the computer cover” on
page 27.
14 Serial connector (available on some models)
Use this connector to attach an external modem, a serial printer, or other devices that use a 9-pin serial
connector.
15 PS/2 keyboard connector (available on some models)
Use this connector to attach a Personal System/2 (PS/2) keyboard.
16 PS/2 mouse connector (available on some models)
Use this connector to attach a PS/2 mouse, a trackball, or other pointing devices.
Computer components
Notes:
• Depending on the model, your computer might look slightly different from the illustration.
• To prepare your computer, see “Preparing your computer” on page 54.
Chapter 1. Product overview 5
Figure 3. Component locations
1 Heat-sink-and-fan assembly
3 Coin-cell battery 4 Flex bay (available on some models)
5 Slim optical drive (available on some models)
7 Wi-Fi card (available on some models) 8 M.2 solid-state drive (available on some models)
9 Front bezel
11 Type-2 storage-drive cage (available on some models) 12 Type-1 storage-drive cage (available on some models)
13 Power supply assembly
15 Cover presence switch (also called intrusion switch)
2 Memory modules
6 Front fan
10 Storage-drive bay
14 PCIe card (available on some models)
16 Rear fan
Parts on the system board
Note: The system board might look slightly different from the illustration.
6
P330 User Guide
Figure 4. System board part locations
1 4-pin microprocessor power connector 2 Microprocessor
3 Microprocessor fan connector
5 Front-bezel connector 6 Internal-speaker connector
7 Storage-drive activity indicator
9 10-pin system board power connector
11 Front-fan connector
13 SATA 3 connector 14 SATA 4 connector or eSATA connector
15 SATA 2 connector 16 SATA 1 connector
17 M.2 solid-state drive slot 18 Wi-Fi card slot
19 Thermal-sensor connector
21 Front USB 2.0 connectors (available on some models)
23 Serial port (COM) connector
25 PCIe x16 card slot (negotiable link width x4) 26 PCIe x1 card slot
27 PCIe x16 card slot 28 Coin-cell battery
29 Rear-fan connector
31 DisplayPort connector
4 Memory slots (DIMM)
8 Flex bay fan connector
10 SATA power connectors
12 Clear CMOS/Recovery jumper
20 ThinkStation
22 Parallel connector
24 Thunderbolt™ control connector
30 E-lock connector
32 Cover presence switch connector (Intrusion switch
®
LED connector
connector)
33 PS/2 keyboard and mouse connector
Chapter 1. Product overview 7
Internal storage drives
Internal storage drives are devices that your computer uses to read and store data. You can add drives to
your computer to increase storage capacity and enable your computer to read other types of media. Internal
storage drives are installed in bays.
When you remove or install an internal storage drive, note the type and size of the drive that each bay
supports and correctly connect the required cables. Refer to the appropriate section in Chapter 7 “Hardware
removal and installation” on page 53 for instructions on how to remove or install internal storage drives for
your computer.
The following illustration shows the locations of the storage drives.
Note: The computer hardware might look slightly different from the illustration.
Figure 5. Storage-drive bay locations
1 Type-1 storage-drive cage
3 Flex bay (available on some models)
8 P330 User Guide
2 SD card slot (available on some models)
4 M.2 solid-state drive slot
5 Type-2 storage-drive cage 6 Type-1 storage-drive bay
7 PCIe card slots (3)
1 Type-1 storage-drive cage
You can install a 3.5-inch storage drive or a 2.5-inch storage drive in this cage.
2 SD card slot (available on some models)
An SD card is installed in some computer models.
3 Flex bay (available on some models)
Depending on your computer model, one of the following devices might be installed in the flex bay:
• Flex module
• Front-access storage enclosure
• Flex storage enclosure
4 M.2 solid-state drive slot
One M.2 solid-state drive is installed in some computer models.
5 Type-2 storage-drive cage
You can install a 2.5-inch storage drive in this cage.
6 Type-1 storage-drive bay
You can install a 3.5-inch storage drive or a 2.5-inch storage drive in the storage-drive bay.
7 PCIe card slots (3)
You can install compatible PCIe cards and PCIe solid-state drives in the PCIe card slots.
Machine type and model label
The machine type and model label identifies your computer. When you contact Lenovo for help, the machine
type and model information helps support technicians to identify your computer and provide faster service.
The following is a sample of the machine type and model label.
Note: The computer hardware might look slightly different from the illustration.
Chapter 1. Product overview 9
MT-M XXXX-XXXXXX
S/N XXXXXXXX
Figure 6. Machine type and model label
Computer features
For your specific computer model, some features might vary or not apply.
Information about your computer
• To view basic information (such as microprocessor and memory information) about your computer, do the
following:
1. Click the Start button to open the Start menu.
2. Click Settings ➙ System ➙ About.
• To view detailed information about the devices (such as the network adapters) on your computer, do the
following:
10
P330 User Guide
1. Right-click the Start button to open the Start context menu.
2. Click Device Manager.
3. Locate and double-click your device in Device Manager to view device properties. Type the
administrator password or provide confirmation if prompted.
Memory
Up to four double data rate 4 (DDR4) error correction code (ECC) unbuffered dual inline memory modules
(UDIMMs) or DDR4 non-ECC UDIMMs
Internal drives
Your computer supports the following storage drives:
• SD card (available on some models)
• Hard disk drive (available on some models)
• M.2 solid-state drive with the Intel Optane technology (available on some models)
• M.2 solid-state drive without the Intel Optane technology (available on some models)
• Slim optical drive (available on some models)
• Solid-state drive (available on some models)
To view the amount of storage drive space, do the following:
1. Right-click the Start button to open the Start context menu.
2. Click Disk Management and follow the instructions on the screen.
Video features
• PCIe x16 graphics card slots on the system board for discrete graphics cards
• Video connectors on a discrete graphics card:
– DVI connector (available on some models)
– DisplayPort connector (available on some models)
– Mini DisplayPort connector (available on some models)
Audio features
Integrated audio controller supports the following connectors and devices on your computer:
• Audio line-out connector
• Headset connector
• Internal speaker
• Microphone connector
Input/Output (I/O) features
• 100/1000 Mbps Ethernet connector
• 9-pin serial connector
• Audio connectors (audio line-out connector, microphone connector, and headset connector)
• HDMI connector (available on some models)
• Display connectors (DisplayPort connector, DVI connector, and Mini DisplayPort connector) (vary by
graphics card)
• PS/2 keyboard connector (available on some models)
Chapter 1. Product overview 11
• PS/2 mouse connector (available on some models)
• USB connectors
• USB-C connector
Expansion
• Flex bay (available on some models)
• Memory slots
• M.2 solid-state drive slot
• PCIe x1 card slot
• PCIe x16 card slot
• PCIe x16 card slot (negotiable link width x4)
• SD card slot (available on some models)
• Storage-drive bay
• Storage-drive cages (available on some models)
Power supply
Your computer comes with one of the following power supplies:
• 250-watt automatic voltage-sensing power supply
• 400-watt automatic voltage-sensing power supply
Wireless features
Depending on your computer model, the following wireless features are supported:
• Wireless LAN
• Bluetooth (available on some models)
System management features
• Ability to store power-on self-test (POST) hardware test results
• Desktop Management Interface (DMI)
Desktop Management Interface provides a common path for users to access information about all
aspects of a computer. The information includes the processor type, installation date, attached printers
and other peripherals, power sources, and maintenance history.
• ErP LPS compliance mode
The energy-related products directive (ErP) lowest power state (LPS) compliance mode reduces the
consumption of electricity when your computer is in sleep or off mode. For more information, see
“Enabling or disabling the ErP LPS compliance mode” on page 34.
• Intelligent Cooling Engine (ICE)
The energy-related products directive (ErP) lowest power state (LPS) compliance mode reduces the
consumption of electricity when your computer is in sleep or off mode. For more information, see
“Switching between better acoustic and better thermal performance” on page 35 and “Enabling or
disabling the system to record thermal alert logs” on page 35.
• Intel
®
Standard Manageability (ISM)
Intel Standard Manageability builds certain functionalities into computer hardware and firmware.
Therefore, computers are less expensive for businesses and easier to monitor, maintain, update, upgrade,
and repair.
• Intel Active Management Technology (Intel AMT)
12
P330 User Guide
With specific Intel platform capabilities and third-party management and security applications, Intel Active
Management Technology enables IT administrators or managed service providers to easily and remotely
discover, repair, and protect their networked computing assets.
• Preboot Execution Environment (PXE)
Preboot Execution Environment enables you to start computers using a network interface. This manner is
independent of starting computers from data storage devices (such as the hard disk drive) or installed
operating systems.
• System Management (SM) basic input/output system (BIOS) and SM software
The SM BIOS specification defines data structures and access methods in a BIOS. Therefore, a user or an
application can store and retrieve information specific about the computer in question.
• Wake on LAN (WOL)
Wake on LAN is an Ethernet computer networking standard that allows a computer to be turned on or
woken up by a network message. The message is usually sent by a program running on another computer
on the same local area network.
• Windows Management Instrumentation (WMI)
Windows Management Instrumentation is a set of extensions to the Windows Driver Model. It provides an
operating system interface through which instrumented components provide information and notification.
Security features
• Ability to enable and disable a device
• Ability to enable and disable USB connectors individually
• Antivirus program
• BIOS passwords and Microsoft
®
Windows® accounts to deter unauthorized use of your computer
• Computrace Agent software embedded in firmware
• Cover presence switch (also called intrusion switch)
• Firewalls
• Smart USB Protection function
• Startup sequence control
• Startup without a keyboard or mouse
• Support for a cable lock
• Support for a Kensington-style cable lock
• Support for a padlock
• Trusted Platform Module (TPM)
Preinstalled operating system
Your computer is preinstalled with the Windows 10 operating system. Additional operating systems might be
identified by Lenovo as compatible with your computer. To determine if an operating system has been
certified or tested for compatibility, check the Web site of the operating system provider.
Computer specifications
This section lists the physical specifications for your computer.
Dimensions
• Width: 165 mm (6.5 inches)
• Height: 376 mm (14.8 inches)
Chapter 1. Product overview 13
• Depth: 328 mm (12.91 inches)
Weight
Maximum configuration as shipped: 10.6 kg (23.37 lb)
Environment
• Air temperature:
Operating: From 10°C (50°F) to 35°C (95°F)
Storage in original shipping package: From -40°C (-40°F) to 60°C (140°F)
Storage without package: From -10°C (14°F) to 60°C (140°F)
• Humidity:
Operating: 30%–90% (non-condensing)
Storage: 20%–90% (non-condensing)
• Altitude:
Operating: From -15.2 m (-50 ft) to 3048 m (10 000 ft)
Storage: From -15.2 m (-50 ft) to 10 668 m (35 000 ft)
Electrical input
• Input voltage: From 100 V ac to 240 V ac
• Input frequency: 50/60 Hz
Programs
This section provides information about the programs on your computer.
Accessing a program on your computer
To access a program on your computer, do one of the following:
• From Windows Search:
1. Type the program name into the search box next to the Start button.
2. In the search results, click the name of the desired program to launch the program.
• From the Start menu or Control Panel:
1. Click the Start button to open the Start menu. Then, click the name of the desired program to launch
the program.
2. If the program name is not displayed on the Start menu, access the program from Control Panel.
a. Click the Start button to open the Start menu.
b. Click Windows System ➙ Control Panel.
c. View Control Panel by Large icons or Small icons, and then click the name of the desired program
to launch the program.
An introduction to Lenovo programs
This section provides information about the major Lenovo programs available on your operating system.
14
P330 User Guide
• Lenovo Vantage
Your computer’s best features and capabilities should be easy to access and understand. With Lenovo
Vantage, they are.
Use Lenovo Vantage to do the following:
– Manage updates, get the latest drivers, and keep the software on your computer up-to-date.
– Protect yourself from malicious Wi-Fi networks.
– Optimize your computer performance, monitor your computer health.
– Access your user guide, check warranty status, and view accessories customized for your computer.
– Read how-to articles, explore Lenovo forums, and stay up-to-date on technology news with articles
and blogs from trusted sources.
– Configure hardware settings.
– Create and manage your Lenovo ID.
This app is filled with exclusive Lenovo content to help you learn more about what you can do with your
Lenovo computer.
Chapter 1. Product overview 15
16 P330 User Guide
Chapter 2. Using your computer
This chapter provides information to help you use the various features provided by your computer.
Registering your computer
When you register your computer with Lenovo, you enter required information into a Lenovo database. The
information enables Lenovo to contact you when there is a recall or other severe problem and provide
quicker service when you call Lenovo for help. In addition, some locations offer extended privileges and
services to registered users.
To register your computer with Lenovo, go to
instructions on the screen.
https://support.lenovo.com/productregistration and follow the
Setting the computer volume
To set the computer volume, do the following:
1. Click the volume icon in the Windows notification area on the taskbar.
Note: If the volume icon is not displayed in the Windows notification area, add the icon to the
notification area. See the Windows help system.
2. Follow the instructions on the screen and the hover text to adjust the volume, mute the speaker, or
unmute the speaker.
Using a disc
This section provides instructions on how to use a disc and the optical drive.
Guidelines about using the optical drive
When using the optical drive, follow these guidelines:
• Do not place the computer in a location where the drive is exposed to any of the following conditions:
– High temperature
– High humidity
– Excessive dust
– Excessive vibration or sudden shock
– An inclined surface
– Direct sunlight
• Do not insert any object other than a disc into the drive.
• Do not insert damaged discs into the drive. Warped, scratched, or dirty discs can damage the drive.
• Before moving the computer, remove the disc from the drive.
Handling and storing a disc
When handling and storing a disc, follow these guidelines:
• Hold the disc by its edges. Do not touch the surface of the side that is not labeled.
© Copyright Lenovo 2018 17
• To remove dust or fingerprints, wipe the disc with a clean, soft cloth from the center to the outside. Wiping
the disc in a circular direction might cause loss of data.
• Do not write or stick paper on the disc.
• Do not scratch or mark the disc.
• Do not place or store the disc in direct sunlight.
• Do not use benzene, thinners, or other cleaners to clean the disc.
• Do not drop or bend the disc.
Playing and removing a disc
To play a disc, do the following:
1. With the computer on, press the eject/close button on the front of the optical drive. The tray slides out of
the drive.
2. Insert a disc into the tray. Some optical drive has a snap hub in the center of the tray. If your drive has a
snap hub, support the tray with one hand and then push the center of the disc until it snaps into place.
3. Press the eject/close button again or gently push the tray forward to close the tray. The disc player
program starts automatically. For more information, refer to the help system of the disc player program.
To remove a disc from the optical drive, do the following:
1. With the computer on, press the eject/close button on the front of the optical drive. The tray slides out of
the drive.
2. Carefully remove the disc from the tray.
3. Press the eject/close button again or gently push the tray forward to close the tray.
Note: If the tray does not slide out of the drive when you press the eject/close button, turn off your
computer. Then, insert a straightened paper clip into the emergency-eject hole adjacent to the eject/close
button. Use the emergency eject only in an emergency.
Recording a disc
If your optical drive supports recording, you can record a disc.
Recording a disc using Windows tools
To record a disc using Windows tools, do one of the following:
• Burn a disc using the AutoPlay window.
1. Ensure that the disc is played automatically.
a. Click the Start button to open the Start menu.
b. Click Settings ➙ Devices ➙ AutoPlay.
c. Select or turn on Use AutoPlay for all media and devices.
2. Insert a recordable disc into the optical drive that supports recording. The AutoPlay window opens.
3. Follow the instructions on the screen.
• Burn a disc using Windows Media
1. Insert a recordable disc into the optical drive that supports recording.
2. Open Windows Media Player. See “Accessing a program on your computer” on page 14.
3. Follow the instructions on the screen.
• Burn a disc from an ISO file.
®
Player.
18
P330 User Guide
Loading...