Lennox TK3-33BL, TK3-36BL, TK3-33BS, TK3-36BS, TK3-36PB User Manual
O
S
~
Cat. No. Model Description
775,175M REV. B
H1538 TK3-36BL 3-pc. Black Trim Kit, MPE-36R,
12/2005
H1539 TK3-36PB 3-pc. Brass Trim Kit, MPE-36R
H1540 TK3-36BS 3-pc. Stainless Trim Kit, MPE-36R
H3435 TK3-33BL 3-p c. Black Trim Kit, MPE -3 3R
H3436 TK3-33PB 3-pc. Brass Trim K it, MPE-33R
H1932 TK3-33BS 3-pc. Stainless T rim Kit, MPE-33R
INSTALLATION INSTRUCTIONS FOR TRIM KITS
FOR USE WITH MODELS MPE-33R AND MPE-36R ELECTRIC FIREPLACE
* KIT CONTENTS:
1 ea. Top Panel
1 ea. Left Side Panel
1 ea. Right Side Panel
6 ea. Magnets
* Note: Trim Kits with Brass and Stainless Finishes also include:
1 ea. Left Side Channel
1 ea. Right Side Channel
1 ea. Top Channel
Double-sided tape on panels
(If the kit you purchased includes channels and double-sided tape, they
should be used)
*Side Channels
Figure 1
CAUTION: CAREFULLY SEPARATE THE MAGNETS BY TWISTING
THEM APART. BE VERY CAREFUL WHEN HANDLING, BECAUSE
THE MAGNETS ARE VERY POWERFUL AND CAN SNAP TOGETHER UNEXPECTEDLY AND POSSIBLY PINCH THE SKIN OR
FRACTURE THE MAGNETS.
TOOLS REQUIRED:
None
INSTALLATION INSTRUCTIONS:
This kit contains trim panels used to finish the gaps between the wallboard or optional mantel and the fireplace, providing the appliance a finished built-in look.
ENSURE FIREPLACE IS COOL TO THE TOUCH BEFORE STARTING INSTALLATION OF THE TRIM KIT
Step 1. Place 2 magnets on each side of the fireplace, placed at approxi-
mately 8” from the top and 8” from the base. See Figure 2.
Top Panel
Right Panel
Left Panel
*Top Channel
Magnets
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Page 1 of 2
LENN
X HEARTH PRODUCT
KITS AND ACCESSORIES
8”
Figure 2
Step 2.
Brass and Stainless Trim Kits - Proceed to Step 3.
Black Trim Kits - Proceed to Step 4.
Step 3. Place the side channels over the magnets (See Figure 3 ).
Ensure that the two side channels are flush with the bottom of the
fireplace. The wider side of the side channel should be on the front of
the fireplace face after installation.
Figure 3
Step 3. Peel off the backing on the double-sided tape on the backside
of each side trim panel (see Figure 4 ). Avoid touching the sticky
surface of the tape.
Approximate
Magnet
Placement
Side
Channel
Ensure
Channel is
Flush with
Base
ane
♦
e
-
Backing
Figure 4
Backside of Side
Trim Panel
Double
Sided
Tape
Step 4. Install the side trim panels onto each side of fireplace face as
follows:
Brass and Stainless Trim Kits – Place side trim over channels,
then press firmly so double sided tape adheres panels to channels (see Figure 5 ).
Black Trim Kits – Place side trim panels over magnets on each
side of the fireplace face as shown in Figure 5.
Note: Magnets were installed on Step 1, Figure 2.
Right Side
Trim P
l
Figure 5
Step 5.
Brass and Stainless Trim Kits - Peel off the backing on double-
sided tape on the backside of the top trim panel. Press fit the top
channel against the top trim panel as shown in Figure 6.
Black Trim Kits – Proceed to Step 6.
Step 6. Place 2 magnets on the backside of the top trim panel as shown in
Figure 6.
Backside of Top
Trim Panel
~ 3”
Typical
Magnet
♦Top Channel
♦Double-sided Tape
Figure 6
Black Trim kits do not include channels or doubl
tape. See Note on page 1.
sided
Step 7. Place the Top Trim Panel over the Side Trim Panels as shown
in Figure 7.
Brass and Stainless Trim Kits – The metal channel should
go behind the side trim panels. Squeeze top and side trim
pieces together.
Black Trim Kits – The magnets act as support to hold the
trim panel in place.
Figure 7
Completed Trim Panel Installation
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
LENNOX reserves the right to make changes at any time, without notice, in design, materials,
specifications, prices and also to discontinued colors, styles and products.
Consult your local distributor for fireplace code information
Printed in U.S.A Lennox Hearth Products 2004
.
P/N 775,175M REV. B, 12/2005 Page 2 of 2 1110 West Taft Avenue • Orange, CA 92865
Loading...