INSTALLATION AND OPERATION MANUAL
Free-Standing
EPA Certified
Wood-Burning Stoves
Save These Instructions
For Future Reference
P/N 775214M, Rev. F, 09/2011
Striker™ S160
SWS160
Wood Stoves
Models Striker™ S160
and SWS160
A French manual is available upon request. Order P/N 775214CF.
Ce manuel d’installation est disponible en francais, simplement en faire la demande. Numéro de
la pièce 775214CF.
This appliance must be properly installed and operated in order to prevent the
possibility of a house fire. Please read this entire installation and operation
manual before installing and using your wood stove. Failure to follow
Portland
US
Report # 050-S-03b-2
these instructions could result in property damage, bodily injury or
even death. Contact your local building or fire officials to obtain
a permit and information on any installation requirements
and inspection requirements in your area.
WARNINGS
• Hot! Do not touch! The glass and surfaces of this appliance will
be hot during operation and will retain heat for a while after
shutting off the appliance. Severe burns may result.
• Carefully supervise children in the same room as appliance.
CONGRATULATIONS!
When you purchased your new wood stove, you joined the ranks of
thousands of individuals whose answer to their home heating needs
reflects their concern for aesthetics, efficiency and our environment.
We extend our continued support to help you achieve the maximum
benefit and enjoyment available from your new wood stove.
Thank you for selecting a Lennox Hearth Products wood stove as the
answer to your home supplemental heating needs.
TABLE OF CONTENTS
Using This Manual ......................................................................... 2
Important Safety Information ......................................................... 3
Testing Information ........................................................................ 4
Draft Requirements ........................................................................ 4
Selecting the Proper Venting System ............................................. 4
Negative Pressure Warning ........................................................... 5
Creosote ......................................................................................... 5
Disposal of Ashes ..........................................................................5
Fuel ........................................................................................... 5
Paint Curing ................................................................................... 5
Burn-In Period ...............................................................................5
Clearances to Combustibles ........................................................... 6
Floor Protection .............................................................................6
Reduced Clearances ....................................................................... 6
Alcove Clearances .......................................................................... 6
Chimney and Connector ................................................................. 6
Components Required for Installation ............................................ 6
Installation Clearances ................................................................... 7
Typical Installation Figures ............................................................. 8
Chimney Installation ...................................................................... 9
Manufactured (mobile) Home Installations .................................... 9
Chimney - Wall Pass-Through Requirements ..............................10
Leg and Heatshield Installation .................................................... 11
Outside Air Kit Installation ............................................................ 11
Stove Installation .........................................................................12
Pedestal Installation ..................................................................... 13
Post Installation Checks ............................................................... 14
Brick Installation ..................................................................... 14-15
Operating Hints ............................................................................ 16
Starting and Maintaining a Fire ....................................................16
Blower Operation (optional kit) ................................................... 17
Operating Techniques and Hints................................................... 18
Getting the Most Out of Your Stove ............................................. 18
Maximizing Your Stove’s Overall Efficiency .................................. 18
Achieving Clean, Long Burns ....................................................... 18
Maintenance ................................................................................. 19
Cleaning Glass .............................................................................19
Troubleshooting ...........................................................................20
Do’s and Don’ts ............................................................................21
Replacement Parts List ...........................................................22-26
Accessories .............................................................................27-29
Safety / Listing Labels .............................................................30-31
Product Reference Information .................................................... 32
USING THIS MANUAL
Please read and carefully follow all of the instructions found in this
manual. Please pay special attention to the safety instructions provided
in this manual.
PRODUCT IS SUBJECT TO CHANGE WITHOUT NOTICE
2
IMPORTANT SAFETY AND WARNIING
INFORMATION
READ THIS MANUAL IN ITS ENTIRETY AND UNDERSTAND THESE RULES TO FOLLOW FOR SAFETY.
1. When this room heater is not properly installed, a house
fire may result. To reduce the risk of fire, follow the installation instructions. Contact local building or fire officials
about restrictions and installation inspection requirements
in your area.
2. Wear gloves during installation to avoid injury from sharp
edges on the stove and/or its parts.
3. This unit is designed and engineered to burn only dry, wellseasoned wood. Burning wet wood will greatly reduce the
Stove’s efficiency, produce excessive amounts of smoke
and can cause dangerous chimney fires due to creosote
build-up.
4. Before opening the door, the draft control must be fully open
to avoid possible combustion flash (ignition of hot volatile
gases as the door is opened).
5. Never use gasoline, gasoline-type lantern fuel, kerosene,
charcoal lighter fluid, or similar liquids to start or ’freshenup’
a fire in this heater. Keep all such liquids well away from
the heater while it is in use. DO NOT USE CHEMICALS OR
FLUIDS TO START THE FIRE.
6. While burning, fuel utilizes oxygen from the air in the room.
Be sure to allow an adequate amount of fresh air into the
room where the stove is burning.
7. The outside surface of the stove will be hot while burning
properly and can set items like clothing and curtains on
fire. Keep furnishings and other combustible materials
away from the stove. Using the heat from the stove to dry
wet clothing can be hazardous if clothes are placed too
near the surface of the stove.
8. HOT WHILE IN OPERATION. KEEP CHILDREN, CLOTHING
FURNISHINGS AND COMBUSTIBLE MATERIAL A CONSIDERABLE DISTANCE AWAY. CONTACT MAY CAUSE SKIN BURNS.
Do not allow children to play near the stove without close
supervision. Do not touch the stove while it is burning.
Use extreme caution while the unit is in use. Surface temperatures become dangerously hot and can cause serious
burns.
9. Do not allow anyone to operate the stove who is not familiar
with the operating instructions.
10. Attempts to achieve heat output rates that exceed stove
design specifications can result in permanent damage to
the stove. Never leave your stove unattended on high burn
rates. This may cause overfiring. Overfiring the stove may
cause a house fire. If the stove glows, you are overfiring.
11. Keep a water hose or hand-operated fire extinguisher close
for safety.
12. Smoke Detectors - Since there are always several potential sources of fire in any home, we recommend installing
smoke detectors. If possible, install the smoke detector in
a hallway adjacent to the room (to reduce the possibility
of occasional false activation from the heat produced by
the stove). If your local code requires a smoke detector
be installed within the same room, you must follow the
requirements of your local code. Check with your local
building department for requirements in your area.
13. Inspect your chimney at least once a month during the burn-
ing season to check for soot and creosote accumulations.
Any accumulations over
a professional chimney sweep. Do not attempt to burn out
heavy creosote accumulations with a hot fire. If large accumulations are occurring, review your burning procedures.
14. If a creosote fire should develop, the fire department should
be called immediately and then attempts should be made
to control the fire until assistance arrives. If a “runaway”
fire should develop causing over-heating of the stove, the
door and draft regulators should be closed immediately.
The fire should die down once deprived of oxygen. After a
severe chimney fire, the complete chimney system should
be checked before further use.
15. Do Not Use Grate Or Elevate Fire - Build Wood Fire Directly
On Hearth (firebrick). Do not use andirons or other methods
of supporting the fuel.
16. Please read this entire manual before you install and use
your new room heater. Failure to follow instructions may
result in property damage, bodily injury, or even death.
17. Check all local building and safety codes before installation.
The installation instructions and appropriate code requirements must be followed exactly and without compromise.
In the absence of local codes the following standards and
codes must be followed.
18. In the U.S.A, install in accordance with the National Fire
Protection Association’s Code, NFPA 211, Standards for
Chimneys, Fireplaces, Vents and Solid-Fuel-Burning Appliances, or similar regulations, may apply to the installation
of a Solid-Fuel-Burning appliance in your area. In Canada,
the guideline is established by the CSA Standard, CAN/
CSA-B365-M93, Installation Code for Solid-Fuel-Burning
Appliances and Equipment.
19.
DO NOT CONNECT TO OR USE IN CONJUNCTION WITH ANY
AIR DISTRIBUTION DUCTWORK UNLESS SPECIFICALLY
APPROVED FOR SUCH INSTALLATIONS.
20. WARNING: BURNING IMPROPER FUEL (I.E. CHARCOAL)
CAN RESULT IN CARBON MONOXIDE POISONING, WHICH
MAY LEAD TO DEATH!
21. Carbon Monoxide Poisoning – Early signs of carbon monoxide poisoning resemble the flu with headaches, dizziness,
or nausea. If you have these signs, get fresh air at once!
Have the heater inspected by a qualified service technician.
Some people are more affected by carbon monoxide than
others. These include pregnant women, people with heart
or lung disease or anemia, those under the influence of
alcohol, and those at high altitudes.
22. Failure to use manufacturer provided parts, variations in
techniques and construction materials or practices other than
those described in this manual may create a fire hazard and
void the limited warranty.
23. Do not make any make-shift compromises during installation. Any modification or alteration may result in damage
to the appliance or dwelling and will void the warranty,
certification and listings of this unit.
24. These appliances are designed as supplemental heaters.
Therefore, it is advisable to have an alternate heat source
when installed in a dwelling.
25. Do Not Overfire – If Heater or Chimney Connector Glows,
You Are Overfiring.
26. DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
27. DO NOT BURN GARBAGE OR FLAMMABLE FLUIDS SUCH
AS GASOLINE, NAPHTHA OR ENGINE OIL.
1/8”
thick should be removed by
3
TESTING INFORMATION
Less than
10' (3 m)
10'
(3 m)
3' (914 mm)
Min.
2’ (610 mm) Min.
(914 mm)
Min.
3'
This manual describes the installation and operation of these non-catalytic
wood heaters. These heaters meet the U.S. Environmental Protection
Agency’s emissions limits for wood heaters sold on or after July 1, 1990.
This heater has been developed, tested and constructed in accordance
with the requirements of UL 1482, ULC S627 and HUD standards and
is listed by OMNI Test Laboratories, Portland, OR. It has been approved
for residential, mobile home and alcove installations.
DRAFT REQUIREMENTS
read greater than .04’ W.C. (inches water column) and less than .08”
W.C. As per NFPA-211 standard (see paragraph below), the installer
must take into account all variables within the installation and install the
appliance in such a manner that satisfies the draft requirements of the
appliance. See Chimney Guidelines below to assist you in selecting the
proper venting system for your installation.
American National Standards Institute ANSI/NFPA 211, Standard for
Chimneys, Fireplaces, Vents, and Solid Fuel-Burning Appliances
- See Draft Section: A chimney or vent shall be so designed and con-
structed to develop a flow sufficient to completely remove all flue and
vent gases to the outside atmosphere. The venting system shall satisfy
the draft requirements of the connected appliance in accordance with the
manufacturer’s instructions.
Your wood stove is dependent upon a properly functioning chimney for
optimum performance. It is a high efficiency appliance that loses much
less heat up the chimney than older appliances and fireplaces. For this
reason it is important to match the stove to the chimney. The chimney
has two functions:
1. It draws combustion air into the appliance (without air, no fuel will
burn) and
2. It exhausts combustion by-products. Your new appliance is what is
known as a “natural draft” appliance.
The appliance depends solely on the natural draft of the chimney system
to draw combustion air into the unit. Draft is the force that moves air from
the appliance up into the chimney. The amount of draft in your chimney
depends on the length of the chimney, local geography, nearby obstructions
and other factors. Too much draft may cause excessive temperatures in the
appliance (overfiring). Slow or inadequate draft equals poor combustion
and possible smoking problems. The following are some conditions that
may contribute to poor chimney draft:
1. A chimney too large for your appliance.
2. A chimney with not enough height to produce adequate draft.
3. A chimney with excessive height (this may allow exhaust to cool too
much before exiting, which will stall the rate the exhaust exits).
4. Offsets in the venting system are too restrictive (see Chimney Guide-
lines).
Inadequate draft will cause the appliance to leak smoke into the room
through the stove and the chimney connector joints.
Excessive draft may cause an uncontrollable burn or a glowing red stove
or chimney part.
Chimney Guidelines:
• This appliance requires approximately 12 feet minimum of “effective
draw” provided by the venting system. As a rule of thumb, every 90
degree total direction change in the venting will result in a loss of
approximately 5 feet of “effective draw.” Example: If two 45 degree
offsets are used, subtract 5 feet from the actual vertical vent height
to determine your “effective draw.” In this case if you had 14 feet of
vertical vent, the effective draw would only be approximately 9 feet
(14 ft. - 5 ft. = 9 ft.), therefore it may be necessary to add additional
height to the venting system.
• Do not install an offset within the first two feet above the flue outlet
on the appliance.
• In well insulated and weather tight homes, it may be difficult to establish
a good draft up your chimney. The poor draft is caused by a shortage
of air in the house. In this situation an Outside Air Kit may need to
be installed (See Negative Pressure Warning on Page 5 and Outside
Combustion Air on Page 11).
Chimney Height Requirements
The chimney must extend 3’ (.92m) above the level of roof penetration
and a minimum of 2’ (.61m) higher than any roof surface within 10’
(3m) (see below). Check with your local building officials for additional
requirements for your area.
Overfiring Damage - If the heater or chimney connector glows, you are
overfiring. Other symptoms may include: Cracking, warping or burning
out of components, plated accessories may turn color, stove glass may
develop a haze, which will not come off with cleaning.
Overfiring of a stove is a condition where excessive temperatures are
reached, beyond the design capabilities of the appliance. The damage
that occurs from overfiring is not covered under the manufacturer’s
limited warranty.
Also see Troubleshooting on Page 20.
SELECTING THE PROPER VENTING SYSTEM
The appliance is merely one component of a larger system. The other
equally important component is the venting system. This is necessary for
achieving the required flow of combustion air to the fire chamber and for
safely removing unwanted combustion byproducts from the appliance.
If the venting system’s design does not promote these ends, the system
may not function properly. Poorly functioning venting systems may create
performance problems as well as be a safety hazard. A draft test should
4
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Figure 1 - Chimney Height Requirements
To pass inspection in nearly any jurisdiction, the chimney must meet both
safety and exhaust flow requirements. The (3’ by) 2’ by 10’ rule applies
to both masonry and factory-built chimneys.
* Ref. USA - National Standard, NFPA 211-latest edition and Canada
National Standard CSA B365-01-latest edition. Vents installed with a
listed cap shall terminate in accordance with the terms of the cap’s
listings.
NEGATIVE PRESSURE WARNING
FUEL
This appliance is not designed to be operated in a negative pressure.
In very airtight homes with large kitchen exhaust fans, furnace cold air
returns, fresh air exchange systems and any other air system in close
proximity to the heating appliance may create a negative pressure in the
same room as the heating appliance. This can create dangerous back
drafting of the stove and chimney joints, drawing combustion by-products
into the home. Be sure your home has adequate makeup air to eliminate
negative pressures caused by the above-mentioned sources. Outside air
connected to the appliance probably will not resolve such a problem as
the stove or fireplace insert is not the source of negative pressure. Lennox
Hearth Products accepts no liability for damages resulting from negative
pressures described here.
Ventilation Requirements - Provide adequate air for combustion. The
fresh air requirements of this appliance must be met within the space
where it will be installed. Ventilation is essential when using a Solid-FuelBurning heater. In well insulated and weather tight homes, it may be
difficult to establish a good draft up the chimney (caused by a shortage
of air in the home). The lack of air is caused by many common household
appliances which exhaust air from the home (such as a furnace, heat
pump, air conditioner, clothes dryer, exhaust fans, fireplaces, and other
fuel burning appliances). Also, the combustion process of this heater
uses oxygen from inside the dwelling. If the available fresh air delivery
in the dwelling is insufficient to support the demands of these appliances,
problems can result (i.e. excessive negative pressure can develop in the
dwelling which will affect the rate at which this appliance can draft thus
resulting in performance problems. To correct this problem it may help
to open a window (preferably on the windward side of the house) or
install an optional outside air kit.
CREOSOTE
Creosote Formation and Need for Removal - When wood is burned
slowly, it produces tar and other organic vapors, which combine with
expelled moisture to form creosote. The creosote vapors condense in the
relatively cool chimney flue of a slow-burning fire. As a result, creosote
residue accumulates on the flue lining. When ignited, this creosote makes
an extremely hot fire. The chimney and chimney connector should be
inspected at least once monthly during the heating season to determine
if a creosote build-up has occurred. If creosote has accumulated (1/8” [3
mm] or more), it should be removed to reduce the risk of a chimney fire.
Establish a routine for the fuel, wood burner and firing technique.
Check daily for creosote build-up until experience shows how often
you need to clean to be safe. Be aware that the hotter the fire the
less creosote is deposited, and weekly cleaning may be necessary
in mild weather even though monthly cleaning may be enough in
the coldest months. Contact your local municipal or provincial fire
authority for information on how to handle a chimney fire. Have a
clearly understood plan to handle a chimney fire.
DISPOSAL OF ASHES
Ashes should be scooped out of a cool stove with a small metal shovel.
Ashes should be placed in a metal container with a tight fitting lid and moved
outdoors immediately. Other waste shall not be placed in this container.
The closed container of ashes should be placed on a non-combustible
floor or on the ground, well away from all combustible materials, pending
final disposal. If the ashes are disposed of by burial in soil or otherwise
locally dispersed, they should be retained in the closed container until
all the cinders have thoroughly cooled. Ashes can ignite up to 72 hours
after removal from the stove.
This unit is designed and engineered to burn, dry, well-seasoned wood only.
Dry, seasoned wood is that which has been cut, split and allowed to dry
under a covered area where air is free to flow and circulate under and
around the wood (not under a tarp or plastic). Make sure wood is not
stacked directly on the ground, it may absorb moisture from the ground.
It should be allowed to dry in these conditions for a minimum of six
months, preferably one year or more.
IT MUST BE UNDERSTOOD
THAT WOOD CANNOT BE LEFT IN ANY KIND OF WET OR DAMP
AREA OR IT WILL NEVER BECOME COMPLETELY SEASONED.
Your stove will not operate at the level that it is meant to unless you use
seasoned, dry wood. Do not burn driftwood or wood that has been in salt
water, doing so will void your warranty. Do not burn treated wood, coal,
garbage, cardboard, solvents, or colored paper. Burning treated wood,
garbage, solvents, or colored paper may result in the release of toxic
fumes. This type of burning will also void your warranty.
Do Not store fuel within space heater installation clearances or within
the space required for refueling and ash removal.
PAINT CURING
If your stove has plated accessories, be sure to clean it with a household
type glass cleaner and a very soft cloth to remove any fingerprints and
residues prior to the first fire and before any fire if the gold has been
handled or soiled. Do not close the door tightly during the “Burn-In
Period.” Also, open the door frequently (every 5-10 minutes) to keep the
gasket from adhering to the curing paint. Ventilate the house well during
these first firings as the paint gives off carbon dioxide and unpleasant
odors. It is recommended that persons sensitive to an imbalance in the
indoor air quality avoid the stove during the curing process.
Your new appliance is painted with a high temperature paint that cures
during the first few firings. We recommend that you put your stove through
a regimen of three burns. The first two should last for 20 minutes each
at 250 degrees (the stove should be allowed to cool completely between
each burn). The third should be a burn of at least 450 degrees F. for 45-60
minutes. The paint will become soft, gummy and emit non-toxic smoke
during these burns. After the stove cools down for the third time, the
paint will harden.
DO NOT BUILD A LARGE ROARING FIRE UNTIL
THIS CURING EFFECT IS COMPLETE OR YOU MAY DAMAGE THE
FINISH OF YOUR STOVE. Spray can touch-ups should be done only
with a high temperature stove paint (cat. no. H8159), available from all
Lennox Hearth Products dealers.
BURN-IN PERIOD
Please be patient with the heat output of your stove for the first few weeks.
The steel will go through a curing process that eliminates moisture, which
is deep in the steel and firebrick. This moisture will reduce initial heat
output of your stove and may make it difficult to start. After you have
broken in the paint on the stove it will be necessary to build hot fires to
thoroughly remove the moisture from the appliance. Running the stove
with the draft fully open for 1 to 1-1/2 hours after starting and adding
generous amounts of fuel during the first week or two should complete
the curing process. We recommend the use of a thermometer attached
to the stovetop or chimney. Temperatures on the connector pipe should
run in the 250-600 degree range.
(DO NOT OVERFIRE THE STOVE
DURING THIS PROCESS. IF THE STOVE OR CHIMNEY BECOMES
RED, REDUCE THE AMOUNT OF AIR ENTERING THE STOVE
IMMEDIATELY).
5
CLEARANCES TO COMBUSTIBLES
WARNING: BE ABSOLUTELY SURE THE DISTANCE BETWEEN THE
HEATER AND THE SURFACE OF ANY COMBUSTIBLE CONSTRUCTION IS NOT LESS THAN SHOWN IN THE FIGURES ON PAGE 7.
Floor Protection
USA - The floor in front and under the heater must be protected with
noncombustible material. The covering must extend 16” in front of the
door opening of the heater and 8” to either side of the door opening
Chimney and Connector
Minimum 6” diameter, minimum 24 MSG black steel connector pipe with
UL103HT listed factory-built chimney suitable for use with solid fuels
or masonry chimney. Horizontal connection not tested, refer to local
building codes for installation. See installation instructions for details.
Restrictions apply! Read instructions before installing.
Clearance dimensions are to 6” (152 mm) flue collar. If a single wall
connector pipe with shield is used, a 1 inch air space is needed between
pipe and shield. Shield attaches to rear of stove pipe and must run from
stove top to ceiling. Pipe shield shall be UL listed.
Canada - The floor in front and under the heater must be protected with
noncombustible material. The covering must extend 457 mm in front of
the door opening of the heater and 200 mm to either side of the stove
body and 200 mm to the rear or to the wall, whichever is smaller.
USA and Canada - A chimney connector / venting extends horizontally
over the floor, protection must also cover the floor under the connector
/ venting and at least 2” (51 mm) to either side.
Reduced Clearances
Clearances to combustible surfaces can be reduced with the use of listed
double wall connector pipe. See the clearances with double wall pipe on
the following page.
Alcove Clearances
Single Wall Pipe - Minimum 48" (1219 mm) width, maximum 48" (1219
mm) depth. Minimum ceiling height is 84” (2134 m).
Double Wall Pipe - Minimum 44" (1117 mm) width, maximum 48" (1219
mm) depth. Minimum ceiling height is 72” (1829 mm).
Residential chimney systems must be from the same brands as listed
for mobile homes but connector pipe may be double wall, single wall or
single wall with shield as listed above.
This appliance may be vented into a code-approved masonry chimney
with flue liner.
Warning: Chimney connector must be in good condition and kept clean.
Do not install damaged parts.
All of the stove connector pipe used must be of the same brand. The
chimney that the stove pipe transitions into may be a different brand.
Other than the transition of the stove pipe into the chimney, do Not mix
different brand vent components. Install all vent components per vent
manufacturer’s instructions.
The chimney connector shall not pass through an attic or roof space,
closet or similar concealed space, or a floor, or ceiling. Where passage
through a wall, or partition of combustible construction is desired, the
installation shall conform to CAN/CSA-B365, Installation Code for SolidFuel-Burning Appliances and Equipment.
There must be an effective vapor barrier at the location where the chimney
or other component penetrates to the exterior of the structure. Follow the
vent manufacturer's detailed instructions.
IMPORTANT NOTE: See Draft Requirements and Selecting a Proper
Venting System on Page 4 to assist you in choosing the proper venting
system for your installation.
Components Required For Installation
Legs AND Bottom Heat Shield or Pedestal Base.
Use all required components specified for this appliance. Do
not substitute.
WARNING: In the event that you remove the blower for any
reason, make sure a cover plate (available from Lennox Hearth
Products) is installed before using the heater. Excessive rear
wall temperatures will result if the stove is burned without the
cover plate. Note: The cover plate is not necessary if a blower
has never been installed because a knock-out will be in place
to act as the cover.
* Other approved chimney brands are Projet, Jakes Evans/GSW, Duravent, Metal Fab, Ameri-Tec, Metalbestos and Industrial Chimney (ICC).
6
Diagram B: Side View-Alcove & Parallel Installation
Diagram A: Top View-Parallel Installation
K
B
A
E
C
D
*L
K
Floor Protection
Floor Protection
Floor Protection
G G
F F
72" Min.
H
I
M
J
I
J
H
†
E
†
E
L
48”
Maximum
Depth
Diagram C: Top
View-Corner
Installation
N
P
T
INSTALLATION CLEARANCES - REFER TO FIGURES 2, 3 AND 4
PIPE INSTALLATION A
6” Single Wall Residential or
Alcove
v
6” Single w/
Pipe Shield
6” Double Wall Residential or
Residential or
Alcove
Alcove or Mobile
Home*
PIPE INSTALLATION
Single Wall Residential or
Alcove
v
Single w/
Pipe Shield
Double Wall
Air-Cooled
Residential or
Alcove
Residential or
Alcove or Mobile
Home*
USA-16”
CAN-483mm
USA-10”
CAN-330mm
USA-10”
CAN-330mm
H (2) I (6) J (2) K L (5)
USA-33-3/4”
CAN-1111mm
USA-33-3/4”
CAN-1111mm
USA-33-3/4”
CAN-1111mm
PIPE INSTALLATION Nu Pu
Single Wall Residential or
Alcove
v
Single w/
Pipe Shield
Double Wall
Air-Cooled
Residential or
Alcove
Residential or
Alcove or Mobile
Home*
30"
762mm
30"
762mm
30"
762mm
Figure 2
B (1)
14”
356mm
8”
200mm
8”
200mm
USA-47-3/4”
CAN-1340mm
USA-41-3/4”
CAN-1188mm
USA-41-3/4”
CAN-1188mm
36"
914mm
36"
914mm
36"
914mm
Figure 3
C
USA-21”
CAN-610mm
USA-18”
CAN-533mm
USA-18”
CAN-533mm
USA-33-1/2”
CAN-1003mm
USA-33-1/2”
CAN-1003mm
USA-33-1/2”
CAN-1003mm
T (6)
USA-58-1/2”
CAN-1645mm
USA-52”
CAN-1486mm
USA-52”
CAN-1486mm
D (1)
12-1/2”
318mm8”200mm
9-1/2”
241mm8”200mm
9-1/2”
241mm8”200mm
E†
USA-16”
CAN-450mm
USA-16”
CAN-450mm
USA-16”
CAN-450mm
† USA=8" (200mm) from door opening,
Canada=8" (200mm) from sides and back
of unit
u
Dimensions to Stove Body
v
Clearances may only be reduced by means
approved by the regulatory authority.
* Mobile Home - USA only
F (1,4)
9-3/4”
248mm
5-1/2”
140mm
5-1/2”
140mm
USA 0"
CAN-200mm
USA 0"
CAN-200mm
USA 0"
CAN-200mm
G (4)
USA-18”
CAN-533mm
USA-13-1/2”
CAN-419mm
USA-13-1/2”
CAN-419mm
M
84”
2134mm
84”
2134mm
72”
1829mm
Top View Corner Clearance,
Stove and Flue to Wal
Figure 4
6” Ø
Flue Collar
l
Footnotes:
1- These dimensions to the stove body are for reference only. Actual
distances should be measured from the stove’s flue collar.
2- Minimum noncombustible hearth pad dimensions.
3- Shield shall be attached to the rear of the stove pipe with a 1” air
space and must run from the top of the stove to the ceiling.
4- Not applicable to alcove installations.
5- In corner applications, when installed at minimum back wall clear-
ances, the required floor protection is dimensioned off the back
plane of the stove, therefore the floor protection required off the
back corners (at a 45 degree angle) only needs to extend to the
wall. This situation will only occur in CANADA installations.
6- Reference dimension only, to assist in planning the installation.
Clearances to connector pipe shall be measured from the flue
collar of the stove.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
7
Single Wall Pipe
Using 6” Diameter Single Wall Connector Pipe
STAINLESS STEEL LINER
Using 6” Diameter Rigid Stainless Steel Liner
INSTALL VENTING SYSTEM PER VENT MANUFACTURERS
INSTRUCTIONS!
Chimney
Termination
Cap
Storm
Collar
Roof
Flashing
Ceiling Support
Assembly
Slip
Adaptor
Single wall stove pipe
must not pass through
attics, closets, walls or
ceilings. It is used to
connect this appliance
to a factory built or
masonry chimney.
INSTALL VENTING SYSTEM PER VENT MANUFACTURERS
INSTRUCTIONS!
Chimney
Termination
Shown with Tubinox™ Stainless
Steel Liner components (see Page
28 for ordering information)
18” (457mm)
Minimum
Masonry
Adaptor
Rain Cap
Flashing
Length
90° Tee
Fasten each stove pipe
connection with at least
3 sheet metal screws.
6” x 24” 24-gage
black steel or 26
gage blued steel
single wall pipe
Fasten stove pipe to
flue collar with 3 sheet
metal screws.
Floor
Protector
Stove
Side View
Figure 5 - Typical Installation
Chimney
Connector
Floor
Protector
Stove
Side View
Figure 6 - Connected to a Masonry Chimney
YOUR CHIMNEY INSTALLATION MUST COMPLY WITH LOCAL
BUILDING AND FIRE CODES.
8
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
CHIMNEY INSTALLATION
• Install chimney as per manufacturer’s instructions. Some brands of
pipe may require removal of the spacer ring in the flue collar.
• All horizontal runs of pipe should be as short as possible and are
required by NFPA No. 211 to have an upward pitch or rise in the same
direction the smoke travels of no less than 1/4” to the linear foot. The
connector pipe must meet minimum clearances in any direction to
walls or other combustible materials. It must attach to a listed double
wall metal chimney at least 6” in diameter or to a masonry chimney
with a flue passage of at least 48 square inches.
• It is required that a chimney connector pipe not extend further than
the inner wall of the flue when it is connected to a masonry chimney
and that it either be cemented to the masonry or be installed without
cement in a thimble connected to the masonry wall. When the
connector is inserted into a thimble, the joint must be tight enough
so that it will not be dislodged in normal use. Install connector at
no less than the minimum clearances from the ceiling when using a
90-degree elbow to pass through combustible constructions.
• Chimney connector pipes should never pass through a floor, ceiling,
fire wall, partition, or combustible construction of any type unless
certain precautions are taken. The best method is to use a listed
thimble and a listed chimney in accordance with the manufacturer’s
directions. NFPA No. 211 gives approved methods for passing a flue
pipe through combustible constructions (see Page 10).
Double Wall Pipe
Using 6” Diameter Type L-Vent Connector Pipe
Mobile (Manufactured) Home Installation Shown
INSTALL VENTING SYSTEM PER VENT MANUFACTURERS
INSTRUCTIONS!
Mobile home installations
require a spark arrestor at the
chimney termination.
Termination Cap
with Spark Arrestor
3 Feet
Minimum
Fasten each stove pipe
connection with at least
3 sheet metal screws.
Remove, if mobile
home is transported
Storm
Collar
Flashing
Support
Box
Manufactured Home Installations
(ref. Figure 7)
This appliance is approved for installation into a manufactured
(mobile) home in the USA ONLY!
Installation should be in accordance with the Mobile Home
Construction and Safety Standard, Title 24 CFR, Part 3280 (in
Canada CAN/CSA Z240 MH), or, when such a standard is not
applicable, the Standard for Mobile Home Installations, ANSI
A225.1.
All mobile home installations require an outside air kit (see Page 27
for ordering information). The stove must be secured to the floor and
grounded to the chassis of the mobile home.
WARNING: DO NOT INSTALL IN SLEEPING ROOM OF A MOBILE
HOME.
CAUTION: THE STRUCTURAL INTEGRITY OF THE MOBILE HOME
FLOOR, WALL AND CEILING/ROOF MUST BE MAINTAINED.
Approved Chimney* - Your stove is approved for use with Class A, UL
103 HT (U.S.) / ULC-S629 (Canada) Listed Residential Type and Building
Heating Appliance Chimney (HT chimney - 2100° Fahrenheit) and double
wall connector pipe from Security™ Chimneys.
Clearances to connector shall be measured from 6” flue collar. Restrictions
apply! Read instructions before installing.
YOUR CHIMNEY INSTALLATION MUST COMPLY WITH LOCAL
BUILDING AND FIRE CODES.
All mobile home installa-
Minimum of
12-15’ of Flue
to achieve a
stable draft.
tions require an outside
air kit (see Page 27 for
ordering information)
and the stove must be
secured to the floor and
grounded to the mobile
home chassis.
7 Feet
Minimum
Fasten stove pipe to
flue collar using 3
sheet metal screws.
Floor
Protector
Chassis
Install Outside Air
Kits per instructions
on Page 11
Figure 7 - Typical Installation
Stove
Side View
DVL Close
Clearance
Connector Pipe
Secure Stove
to floor
Floor
Grounded to Steel Chassis
using a #8 AGW copper
wire or equivalent.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
9
Chimney Connector Systems and Clearances from Combustible
Walls for Residential Heating Appliances (NFPA 211) Refer to
Figure 8
System A
Minimum chimney clearance to brick
and combustibles 2 in. (51mm)
System A. Minimum 3.5 in. (90 mm) thick brick masonry wall
framed into combustible wall with a minimum of 12 in. (305 mm)
brick separation from clay liner to combustibles. Fireclay liner (ASTM
C 315, Standard Specification for Clay Flue Linings, or equivalent),
minimum 5/8 in. (16 mm) wall thickness, shall run from outer surface
of brick wall to, but not beyond, the inner surface of chimney flue
liner and shall be firmly cemented in place.
Clearance: 12 in. (305 mm)
System B. Solid-insulated, listed factory-built chimney length of the
same inside diameter as the chimney connector and having 1 in.
(25.4 mm) or more of insulation with a minimum 9 in. (229 mm) air
space between the outer wall of the chimney length and combustibles.
The inner end of the chimney length shall be flush with the inside of
the masonry chimney flue and shall be sealed to the flue and to the
brick masonry penetration with non-water-soluble refractory cement.
Supports shall be securely fastened to wall surfaces on all sides.
Fasteners between supports and the chimney length shall not penetrate the chimney liner.
Clearance: 9 in. (229 mm)
System C. Sheet steel chimney connector, minimum 24 gauge [0.024
in. (0.61 mm)] in thickness, with a ventilated thimble, minimum 24
gauge [0.024 in. (0.61 mm)] in thickness, having two 1 in. (25.4
mm) air channels, separated from combustibles by a minimum of 6
in. (152 mm) of glass fiber insulation. Opening shall be covered, and
thimble supported with a sheet steel support, minimum 24 gauge
[0.024 in. (0.61 mm)] in thickness.
Supports shall be securely fastened to wall surfaces on all sides and
shall be sized to fit and hold chimney section. Fasteners used to secure
chimney section shall not penetrate chimney flue liner.
Clearance: 6 in. (152 mm)
System D. Solid-insulated, listed factory-built chimney length with
an inside diameter 2 in. (51 mm) larger than the chimney connector
and having 1 in. (25.4 mm) or more of insulation, serving as a passthrough for a single wall sheet steel chimney connector of minimum
24 gauge [0.024 in. (0.61 mm)] thickness, with a minimum 2 in.
(51 mm) air space between the outer wall of chimney section and
combustibles. Minimum length of chimney section shall be 12 in.
(305 mm). Chimney section concentric with and spaced 1 in. (25.4
mm) away from connector by means of sheet steel support plates
on both ends of chimney section. Opening shall be covered, and
chimney section supported on both sides with sheet steel supports
of minimum 24 gauge [0.024 in. (0.61 mm)] thickness.
Supports shall be securely fastened to wall surfaces on all sides and
shall be sized to fit and hold chimney section. Fasteners used to secure
chimney section shall not penetrate chimney flue liner.
Clearance: 2 in. (51 mm)
Additional requirements:
1. Insulation material used as part of wall pass-through system shall be
of noncombustible material and shall have a thermal conductivity of
1.0 Btu-in./hr-ft
2
- ºF (4.88 kg-cal/hr-m2 - ºC) or less.
2. All clearances and thicknesses are minimums; larger clearances and
thicknesses shall be permitted.
3. Any material used to close up an opening for the connector shall be of
noncombustible material.
4. A connector to a masonry chimney, except for System B, shall extend
in one continuous piece through the wall pass-through system and the
chimney wall to the inner face of the flue liner, but not beyond.
10
Minimum
12 in. (305mm)
to combustibles
System B
System C
Minimum Chimney Clearance from Masonry to Sheet Steel
Supports & Combustibles – 2 in. (51mm)
Factory Built
Chimney Length
Air Space – 9 in.
(228.6mm) Min.
Minimum chimney clearance to sheet
steel supportrs and combustibles
2 in. (51mm)
2 Ventilated Air
Channels, Each
1 in. (25.4 mm)
Construction of
Sheet Steel
System D
Chimney
Section
Air Space – 2 in.
(51mm) Min.
Figure 8 - Chimney Connector Systems and Clearances from Combustible Walls
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Chimney
flue
Masonry chimney
constructed to NFPA 211
Nonsoluble
Refractory
Cement
Chimney Length
Flush with
Inside of Flue
Chimney
flue
Masonry chimney
constructed to NFPA 211
Chimney
flue
Masonry chimney
constructed to NFPA 211
Minimum chimney clearance to sheet steel
supports and combustibles 2 in. (51mm)
Sheet Steel
Supports
Chimney
Connector
Masonry chimney
constructed to NFPA 211
Minimum clearance
12 in. (305mm)
of brick
Fire clay
liner
Sheet Steel Supports
2 Air Channels, Each 1
in. (25.4 mm)
Sheet Steel Supports
Sheet Steel Supports
Chimney
connector
Min. Clearance
9 in. (229mm)
Chimney
Connector
Use Chimney
Mfrs. Parts to
Attach
Connector
Solid-Insulated
Listed FactoryBuilt Chimney
Length
Chimney
Connector
Min. Clearance
2 in. (51 mm)
1 in. (25.4 mm)
air space to
chimney length
Chimney connector
Chimney length
LEG AND HEATSHIELD INSTALLATION
Note: The threaded rods used to bolt the legs to the stove are packaged with the heatshield, as a heatshield is required when a stove is
installed on legs.
Residential and Mobile Homes
(Bolting down and grounding of stove are required only in mobile
homes).
Open all cartons, if any and remove the contents upon receipt and check
for any damaged or missing parts. If there is hidden damage, notify your
freight company or Lennox Hearth Products dealer immediately.
CAUTION: Wear gloves during installation in case of sharp
edges on the stove.
BACK
Heat Shield
Mounting Holes
Leg Installation
1. Carefully place stove on its back. Be careful not to scratch the
stove, use a piece of cardboard or carpet to protect the back of
the stove.
2. Mount all four legs as shown in Figure 9.
3. First, screw the threaded rods into the holes at the four corners
on the bottom of the stove. Screw the threaded rods into the
firebox three full rotations or 3/16 to 1/4” (if the rear rods are
screwed in too far they will lift the bricks off the bottom of the
stove). Use a washer and nut to secure the leg. Be sure the
legs are mounted squarely on the firebox bottom. Tighten nuts
securely.
4. Use the two bolts and washers provided with the heatshield kit
to mount the heatshield as shown in Figure 10.
5. Do not over tighten the heatshield mounting bolts as it may bend
the heatshield.
Threaded Rod
Figure 10
FRONT
Air Channel
OUTSIDE AIR KIT INSTALLATION
To install the “Outside Air Kit,” position the clip so that the nut is directly
above the hole punched in the back of the heatshield (See Figure 11).
Install the outside air adapter box on the stove by sliding it into the air
channel located between the bottom heatshield and the stove bottom until
the oblong ring is approximately 1/4” from the rear edge of the lower
heatshield. Make sure the ring is facing down. Thread the 1/4” bolt up
through the nut in the clip until snug against the adapter box.
Expanded View of Clip
Line up the hole in the clip with the hole in the
rear center of the bottom heatshield
Figure 9
Washer
Nut
Figure 11
To locate the hole in the hearth for outside air, mark a 4” circle on the
hearth. The circle’s center should be 2-3/4” directly back from the center
of the flue outlet and 5/8” to the left side.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Clip
1/4” Bolt
11
STOVE INSTALLATION
1. If not previously installed, install floor protection and move the
heater into the desired location.
2. Position the stove on your floor protection in the exact location
where it is to be located, making sure all minimum clearances are
met.
3. If you are installing outside air on your stove, mark a 4” circle on
the floor protection just below the oblong ring. When cut out, this
hole will accommodate the flexible outside air tube.
4. If the stove is to be fastened to the floor, locate the hold down
brackets inside the leg box and mark the floor protection below the
holes in the brackets.
5. If you are installing outside air on your stove, remove the stove and
cut the floor protection and the floor where the 4” air tube circle had
been previously drawn. If the stove is to be fastened to the floor,
drill 1/2” holes through the floor protection only, at the marks that
were for fastening the stove to the floor if so desired. Slip the flexible
outside air tube through the hole in the floor, leaving 1” of tube above
the floor protector surface, using tape to hold it in place.
6. Place the stove on the floor protection so that the previously cut or
drilled holes line up. Attach the stove to the floor with the lag bolts
if so desired.
7. If you are installing outside air on your stove place the hose clamp
over the flexible air tube and slide the tube up over the 4” ring on
the outside air adaptor box and tighten the hose clamp. Push the
outside air adaptor forward 1/4” until full contact is made with the
lower heatshield. Tighten the 1/4” bolt until the adaptor box is held
firmly in place. Use silicone sealant to create a seal between the
flexible air tube and your floor protection.
8. If it is necessary to level, secure or ground your stove, use the holes
in the bottom of the leg for those applications. To level the stove on
Olympic cast legs, locate the front leg that is not touching the hearth
pad. Insert the allen head screw through the slotted washer (supplied
with the legs) and into the threaded hole in the bottom of the leg.
See Figure 12. Push the slotted washer down until it touches the
hearth pad and then tighten the screw into the leg. Should any other
leg not be resting on the hearth pad, install a washer and screw in
that leg as well.
9. Install baffle boards and baffle blanket as per instructions on Pages
14 and 15. It is highly recommended that the baffle be assembled
before the chimney is installed so that the baffle blanket can be
adjusted into place through the flue collar.
10. If installed into a mobile home, the stove shall be grounded to the
mobile home chassis with a #8 AGW copper wire or equivalent.
11. For residential installations, install the first section of stove pipe
with the crimped end going down inside the flue collar on the heater.
Continue with your stove pipe, installing each section-crimped
end down. Make the final connection to your chimney. Your dealer
carries the necessary pipe and fittings to connect to the various listed
factory-built chimneys.
YOUR CHIMNEY INSTALLATION MUST
COMPLY WITH LOCAL BUILDING AND FIRE CODES.
12. Be sure to fasten each stove pipe connection with at least 3 sheet
metal screws.
13. Install chimney as per manufacturer’s instructions. Some brands of
pipe may require removal of the spacer ring in the flue collar.
14. All horizontal runs of pipe should be as short as possible and are
required by NFPA No. 211 to have an upward pitch or rise in the same
direction the smoke travels of no less than 1/4” to the linear foot.
The connector pipe must meet minimum clearances in any direction
to walls or other combustible materials. It must attach to a listed
double wall metal chimney at least 6” in diameter or to a masonry
chimney with a flue passage of at least 48 square inches.
15. It is required that a chimney connector pipe not extend further than
the inner wall of the flue when it is connected to a masonry chimney
and that it either be cemented to the masonry or be installed without
cement in a thimble connected to the masonry wall. When the
connector is inserted into a thimble, the joint must be tight enough
so that it will not be dislodged in normal use.
Install connector at no less than the minimum clearances from the
ceiling when using a 90-degree elbow to pass through combustible
constructions.
16. Chimney connector pipes should never pass through a floor, ceiling,
fire wall, partition, or combustible construction of any type unless
certain precautions are taken. The best method is to use a listed
thimble and a listed chimney in accordance with the manufactures
directions. NFPA No. 211 gives approved methods for passing a flue
pipe through combustible constructions.
Insert the allen
head screw
through the
slotted washer
Figure 12
12
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
PEDESTAL INSTALLATION
(For ash drawer pedestal see instructions included with pedestal)
Residential and Mobile Homes
(Bolting down and grounding are required only in mobile homes)
CAUTION: Wear gloves during installation in case of sharp
edges on the stove.
5. If required, install the Outside Air Kit (cat. no. 71112) as per the
following instructions. To locate the hole in the hearth for outside
air mark and cut a 4” (102 mm) hole in the hearth. The hole’s
center should be 3” (76 mm) directly forward from the center
of the flue outlet or locate as per the instructions below.
6. Position the stove on your floor protection in the exact location
where it is to be located, making sure all minimum clearances
are met. Mark the floor protection where the pedestal will be
located, then remove the stove.
1. Remove the heater from the carton, if packaged, upon receipt
and check for any damaged or missing parts.
2. Carefully put the stove on pedestal with the open end of the pedestal
facing the rear.
DO NOT LEAVE THE STOVE UNATTENDED
UNTIL IT IS BOLTED SECURELY TO THE PEDESTAL.
3. Line up the holes in the brackets on the pedestal with the threaded
holes in the bottom of the stove. Use the two 1/2” long bolts
and 3/8” standard washers to bolt the stove to the pedestal. Be
sure to see that the stove is mounted squarely on the pedestal
before tightening the two bolts securely.
4. When installing a pedestal on this stove you MUST plug the four
leg mounting bolt holes, located on the bottom of the stove in
the four corners, with the bolts that were used to mount the
shipping legs. The two rear bolts should not be installed more
than two full rotations to prevent lifting the bricks off the bottom
of the stove.
FAILURE TO INSTALL THESE FOUR BOLTS
PROPERLY WILL RESULT IN REDUCED CONTROL OF THE
STOVE’S COMBUSTION SYSTEM!
7. Make four 1-1/2” (38 mm) cuts in one end of the corrugated
tube and fold the flaps back. Cut a 4” (102 mm) hole through
the floor protection and the floor and insert the corrugated tube
into the hole. Cover it with the supplied screen and fasten it to
the floor protector.
8. Locate the 11-1/2” x 14” (292 mm x 356 mm) metal plate and
paint to match the stove if necessary. Position this piece so that
the 14” (356 mm) dimension evenly overlaps the lips on the back
of the pedestal (see drawing below). Attach this plate to the back
of the pedestal with the self-tapping screws supplied.
9. If the stove is to be fastened to the floor, attach the stove with
the supplied lag bolts, through the pedestal base on opposite
sides, attaching them into the floor beneath the floor protection.
Seal any irregularities with silicone sealer.
10. If installed in a mobile home, the heater shall be grounded to
the chassis with a #8 AGW copper wire or equivalent.
11. Install bricks as per instructions on Pages 14 and 15. It is highly
recommended that the baffle be assembled before the chimney
is installed so that the baffle blanket can be adjusted into place
from the flue outlet.
12. Install chimney as per manufacturer’s instructions.
Block Off Plate is
Required When
Installing Outside
Air Into Unit (Plate
is Included With
Kit # 71112)
Figure 13
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
13
POST INSTALLATION CHECKS
BRICK INSTALLATION
1. Check that all chimney pipe joints are securely fastened.
2. Check that the heater is securely fastened to the floor (if applicable).
3. Make sure the intake vent has clear access to outside air (if applicable).
4. Make sure the outside air vent has been sealed properly to keep
rodents out (if applicable).
5. Be sure all roof flashings are watertight.
6. Be sure the stove is properly grounded (if applicable).
FOR YOUR OWN PROTECTION AND INSURANCE PURPOSES,
HAVE YOUR CHIMNEY AND CONNECTOR PIPE INSTALLATION
INSPECTED BY YOUR LOCAL BUILDING CODE AUTHORITY OR
FIRE MARSHAL BEFORE STARTING A FIRE IN YOUR STOVE.
NOTIFY YOUR INSURANCE COMPANY.
CAUTION: Wear gloves during brick installation in case of
sharp edges inside the stove.
Note: Installation of the baffle boards and baffle blanket is easier when
you can still access the flue outlet, (before connecting the flue vent). Be
sure the baffle blanket is placed flat on the baffle boards so as not
to block exhaust flow to the flue. Use a ruler or a piece of kindling to
reach over the baffle blanket to be sure it is completely flat on top of the
baffle boards.
Measure bricks before installing, as per list of dimensions on next page,
to be sure the correct bricks are installed in the correct location.
1. Install bricks #1-18 in the numbered sequence shown in Figure 14
on Page 15.
2. Next, you will install the rear baffle boards which are the smaller two
of the four baffle boards. The boards will be installed with the 3-9/16”
dimension from the front to the rear of the firebox. These boards
will be placed on the top side of the rear baffle just to the rear of the
middle secondary tube, you will push the baffle boards towards the
rear of the firebox until they fall in place at the rear side of the middle
secondary tube. You will place one board to the far left side of the
firebox and one board to far right side of the firebox. Confirm that
both boards are laying flat on the rear baffle and that they are not
overlapping each other.
14
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
3. Next, you will install the baffle blanket. It will be installed with the
11” dimension from the front to rear of the firebox. Install by lifting
it into place between the front and rear baffle. Place the blanket over
the rear baffle and rear baffle boards that you have just installed. Next
you will place the baffle blanket that is protruding beyond the front
side rear baffle on the top side of the front baffle.
4. The final step of the baffle board & baffle blanket installation will be
installing the front baffle boards. The front baffle boards will be the
two remaining baffle boards which are the larger two baffle boards
of the four baffle board kit. They will be installed with the 7-3/8”
dimension from the front to rear of the firebox. Start by setting the
back side of the board on the rear baffle making sure that it is placed
far enough back to lift up and onto the front baffle. Next you will place
the front edge of the front baffle boards on the top side of the front
baffle and slide them towards the firebox front until it stops against
the front baffle edge. You will do this with each front baffle board
with one to the right side of the firebox and one to the left side of the
firebox. Confirm that the baffle blanket is directly on top of the baffle
boards and that it does not protrude beyond the front baffle or front
baffle boards as shown in Figure 15 (also see note on Page 14).
Figure 14
Rear Baffle
Board
17D
7
1
F
F
2
8
A
F
3
D
11F
12A
9
F
13F
18B
10
F
14F
4
F
5
F
6
D
Brick Sizes
A = 4-1/4” x 9”
B = 2-1/4” x 8-7/8”
D = 2-1/4” x 9”
E = 1-1/2” x 8-7/8”
F = Full Brick (4-1/2” x 9”)
G = 1-1/2” x 9”
15G
16E
Baffle Insulation Parts
18-1/4”
Side Cut-A-Way View of Firebox
Baffle Blanket
1” Thickness
Baffle Blanket
11”
Firebox
Brick
Figure 15
Front Baffle
Board
Figure 16
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
9”
1/2” Thickness
Front Baffle Board
(2 included)
9”
1/2” Thickness
Rear Baffle Board
(2 included)
7-3/8”
3-9/16”
15
OPERATING HINTS
STARTING AND MAINTAINING A FIRE
1. Burn only dry, well-seasoned wood for maximum heat output. In some
states it is illegal to burn wet wood or anything other than clean, dry
wood products.
2. Your stove is designed to operate with the door closed! Operate only
with the door shut tightly at all times except when loading wood and
possibly on start up to establish a draft. Never leave the unit unattended while the front door is slightly opened.
3. DO NOT hit or move the baffle board while loading wood. Occasionally
check the baffle. Make sure the baffle blanket is always flush with the
front of the baffle boards. Loading oversized logs may dislodge the
baffle boards.
4.
CAUTION: THE DRAFT CONTROL MUST BE FULLY OPEN BEFORE OPENING THE DOOR TO AVOID POSSIBLE COMBUSTION
FLASH!! (Ignition of hot volatile gases as the door is opened).
5. Feeding excessive amounts of fuel to the stove should be avoided.
It is important to supply it with sufficient draft and fuel to maintain a
moderately hot fire. If, during overnight burns, heavy creosote deposits
develop inside your stove and on the door, the draft is set too low
- review your burning habits!
CAUTION
Be careful not to abuse door assembly by striking or
slamming it. If the door assembly or glass is broken or
damaged, they must be replaced with factory original
parts before heater can be safely operated. Use only
components provided by the manufacturer as replacement parts.
Be sure to clean plated accessories with a household type
cleaner and a very soft cloth to remove any fingerprints and
residues prior to the first fire.
1. NEVER USE FLAMMABLE LIQUIDS TO START OR REKINDLE
A SOLID FUEL FIRE!!
2. Fully open the primary draft control by pulling the 1” plastic knob
out on the left side (lower front corner) until it stops (away from the
stove). This control determines the amount of air entering the stove.
Pushing it toward the stove reduces the burn rate in the firebox. For
your convenience, the rod on this control is marked with four grooves
to assist you in obtaining repeatable burn rates.
3. Place a small amount of crumpled paper in front of the firebox and
cover it with a few pieces of kindling.
4. Light the paper and allow sufficient time for the kindling to become
fully engulfed in flames. You will now close the wood units front door.
(Your wood units front door may or may not need to be left slightly
open during this start up process, this depends on the stove model
and the amount of draft present. Do not leave the unit unattended
while the front door is slightly open) Once kindling is burning well,
larger pieces of wood may be added, then the door should be fully
closed if there was the need to keep it slightly open during start up.
DO NOT LEAVE THE STOVE UNATTENDED WHILE THE FRONT
DOOR IS SLIGHTLY OPEN.
Figure 17
OK
CAUTION: Do Not alter the adjustment range of the draft
control for increased firing for any reason.
Operate only with fuel door and ash drawer closed. Maintain
all seals in good condition. Do not operate with broken glass.
Do Not build the fire too close to the glass.
Do not operate the appliance with the door open or ajar other
than possibly during start up to create a draft (Do not leave
the unit unattended while the front door is slightly open during start up). Operating the appliance with the door open
other then in initial start up if needed will produce extreme
temperatures within the appliance. Damage caused from
over-firing is not covered under the manufacturers limited
warranty.
5. For best results, use smaller pieces of wood to get the insert tem-
perature very high before loading larger wood for sustained burns.
If necessary, crack the door to allow ignition of the fuel charge. Do
not leave the unit unattended while the front door is slightly open.
Now you can add larger pieces of wood and after several minutes of
high burn, set the left control for the desired heat output. Check the
exhaust in about 15 to 20 minutes. Large amounts of smoke indicate
an improper burn setting (either too high or too low). Adjust and
recheck in 5 to 10 minutes.
16
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
BLOWER OPERATION
Blower Operation
The blower can be operated manually or automatically (blower will
turn on when the stove is hot and turn off when the stove is cool).
The rocker switch on the control panel allows you to select between
manual operation or automatic operation as follows (see Figure 19):
MANUAL OPERATION: Turn rocker switch to the “MANU-
AL” position and adjust rheostat knob to the desired speed. The blower
will have to be manually turned “OFF” by rotating the rheostat knob
clockwise until it clicks.
AUTO OPERATION: Turn rocker switch to the “AUTO” posi-
tion and the rheostat to the ON position (rotate rheostat knob counterclockwise until it clicks). When the stove warms up, the blower will
automatically turn on (adjust rheostat knob to the desired speed setting). When the stove cools down, the blower will automatically turn
off.
Rheostat Operation - The highest blower speed is obtained by turning the rheostat knob counterclockwise until it clicks “ON”, then rotate
towards “HIGH” to increase blower speed. Rotate the knob clockwise
for a lower speed. To turn off, continue to rotate the knob clockwise
until it clicks “OFF.”
Blower Operation Guidelines
While in auto operation mode, the blower will turn off and on based on
the temperature of the appliance. Auto operation ensures there is sufficient heat build-up to warm the air being moved by the blower before the
blower is turned on. Likewise, when the appliance cools off, the blower
is turned off to prevent circulating cool air. Depending on the size and
intensity of the fire it may be necessary to adjust the blower speed accordingly to ensure un-interrupted blower operation. For example a small
fire may require a slower blower speed to keep the heat output by the
blower consistent. If the blower is operated in manual mode, it may be
necessary to adjust the blower speed as the fire begins to burn down and
the appliance is no longer hot enough to effectively heat the air moved
by the blower. If the air coming from the blower feels cool, one should
either decrease the blower speed or stoke the fire to build up more heat.
Blower Speed Control
Knob (rheostat)
Manual / Auto
Rocker Switch
Figure 19 - Blower Controls
WARNINGS
The blower must be plugged directly into a properly
grounded three-prong receptacle, 120 VAC, 60 Hz, single
phase. Do not cut or remove the grounding prong from
this plug. Do not route power cord under or in front of
appliance.
Installation must be in accordance with National Electrical Code, ANSI/NFPA 70 - latest edition. In Canada,
the current CSA C22-1 Canadian Electrical Code - latest
edition.
DANGER: Disconnect power before servicing blower.
In the event that you remove the blower for any reason,
make sure a cover plate (available from Lennox Hearth
Products) is installed before using the heater. Excessive
rear wall temperatures will result if the stove is burned
without the cover plate. The cover plate is not necessary
if a blower has never been installed because a knock-out
will be in place to act as the cover.
NOTE: Turn blower off before opening the door to load the fuel.
NOTE: SWITCH CONDITIONS
GIVEN AT ROOM TEMPERATURE
N/C = NORMALLY CLOSED
N/O = NORMALLY OPEN
= FEMALE DISCONNECT
= MALE DISCONNECT
= STUD CONNECTION
WHT
POWER CORD
Figure 18 - Blower Wiring Schematic
TWO POSITION
SWITCH
MANUAL/TEMPERATURE
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
YLW
CONTROL/OFF
BLK
AUTO-RESET
TEMPERATURE
SWITCH N/O
3-RED
SPEED
3-RED
1-BRN
ROOM AIR
BLOWER
1-BRN
3-RED
4-GRN
4-GRN
17
OPERATING TECHNIQUES AND HINTS
ACHIEVING CLEAN, LONG BURNS
Recent developments in wood-burning technology have made wood-burning a cleaner and more convenient way to heat your home. Overall efficiency
in a wood-burning appliance is a combination of combustion efficiency
and heat transfer efficiency. Whether heating your entire home, or just a
room or two, your understanding of how to best operate your stove or
insert will enhance its overall efficiency and performance. What this can
mean to you is longer, cleaner burns, less wood use and more heat.
GETTING THE MOST OUT OF YOUR STOVE
The following sections will outline techniques you can use to “get the
most out of your stove.” Please read them carefully.
MAXIMIZING YOUR STOVE’S OVERALL EFFICIENCY
It is important to know that for high, combustion efficient, clean burns,
you will need to have sufficient temperatures inside the firebox for
thorough combustion. The best method for determining if you have
sufficient temperatures is to watch the brick lining in your firebox. When
you first light your stove, the bricks will turn a dark brown or black.
After 20 to 30 minutes of a hot fire, most of the bricks should return
to near their original light brown or yellow color. This means the bricks
have reached a high enough temperature for your stove to achieve high
combustion efficiency.
Second and just as important, is achieving a high level of heat transfer
efficiency. Slowing the rate of flow through the stove or insert enhances
heat transfer, thus allowing more time for heat to be transferred into your
home. To do this, be sure to thoroughly preheat your stove and then reduce
the amount of primary air by closing the draft control (lower left) to about
1/2 to 3/4 open. This will decrease the excess oxygen in your flue, which
carries heat up your chimney, but should still be enough air to allow the
stove to produce its maximum heat output. (More air may produce a lightly
greater amount of heat, but will greatly increase wood consumption). When
the area being heated reaches a comfortable temperature, slow the burn
rate by closing the control to further improve heat transfer.
To get the most out of your appliance, you will need to combine good
combustion efficiency with good heat transfer practices. The following
are some tips on how to operate your stove to achieve the highest overall
efficiency.
1. Thoroughly preheat your stove before slowing the burn rate by closing
the draft control.
2. Measure the stove temperature at the hottest point on the stove top
or face. Use this information to repeat burn rates.
3. Once preheated, add wood (if needed) and partially close the draft
control (lower left).
4. Operate your stove as much as possible in the low to medium burn
ranges.
5. Do not lower the draft setting so low as to completely extinguish the
flames in the firebox. Check for at least some small flames 20 minutes
after setting the draft control.
6. Do not continually operate your stove in the high (wide open) setting.
This wastes wood by carrying a great deal of heat up the chimney
and can damage your stove and chimney.
7. Go outside and check your chimney. More than a very small amount
of smoke indicates wasted heat, creosote build-up and pollution.
To achieve long burn times, after having thoroughly preheated the
stove, let the stove top cool down to 275
locate thermometer on the face of the insert just above the door). Now
load the firebox and set the draft control. At this point, you may need to
burn the stove with the draft open for a few minutes to ignite the wood.
All Lennox Hearth Products stoves are EPA tested for emissions at low
burn with the air control completely closed. Whether or not you should
burn your stove with the air control completely closed will depend on
the following factors.
* How you load your wood
* Your chimney type, height and draft
* Your wood type and its moisture content
* The temperature of the stove
* Which model stove or insert you have
Experiment with different loading configurations to achieve longer
burns. Try loading the wood from side to side and nesting it in the ashes
to prevent airflow under and around the wood. Fresh wood should be
loaded to the back of the firebox or to the sides. Hot coals or half burned
wood should be brought towards the front of the firebox. The way you
load your wood can seriously affect burn times. If the new load does not
ignite within a few minutes, try crisscrossing the load to allow more airflow
around the fire, or try a slightly hotter stove temperature.
Determining the lowest setting for efficient low burns. This will require
some experimentation on your part. Try closing the air control all the
way with the stove temperature at 325 to 350 degrees. If the flames are
completely extinguished, open the air control halfway and then slowly
close it until there is only a small amount of flame. It is important to check
the stove about 20 minutes after setting the draft control as it takes this
long for the stove temperature to stabilize. There should still be some
small flames on or above the wood load.
Use 325 degrees as a starting point. You can try starting temperatures
25 degrees higher or lower to achieve desired burn times, start 25 degrees
lower if the stove burns the wood too quickly or 25 degrees higher if there
are no flames in the firebox for more than a few minutes after loading the
wood. You may or may not need to burn the stove with the air control
open for a few minutes prior to setting the draft for a low burn, this will
depend on the factors mentioned above. Be sure not to smolder a fire
overnight. Check your chimney for large amounts of smoke as this
indicates very poor combustion.
It is important to realize that stove technology has changed. Stoves
have changed a great deal in the last few years. This has led to substantial
changes in the methods of operation in new stoves as compared to older
stoves. In old stoves without full brick linings and ceramic insulation,
the rule was “get the stove as hot as possible before setting the draft on
low for overnight burns.” On newer, high technology stoves, this is not
necessary. Although it is still important to have the stove hot enough to
burn efficiently, it will require less preheating. Once you have determined
your optimum operating temperatures for various burn rates, we believe
you will find your stove an extremely convenient way to achieve your
heating needs.
Do not reload the stove for long burns when the stainless secondary
tubes or baffles are glowing red, or when the stove is uncomfortably
hot to load. This indicates the stove is too hot to load for a long burn.
Also, do not load wood for a long burn on a deep bed of hot coals. Try
stirring the coals a few minutes before loading the stove for a low burn
to allow some of the unburned coals time to burn.
to 400 degrees (on Elites,
18
MAINTENANCE
CAUTION
DOOR HINGES: If door hinges need lubricating, use an anti-seize com-
pound (never use oil) available from your Lennox Hearth Products dealer.
DOOR LATCH: If your door latch fails to latch tightly and the gasket is
in good condition, place a length of pipe (cheater bar) over the inside
portion of the door handle and bend slightly toward the door until the
proper adjustment is obtained. If the door handle does not close easily,
apply high temperature anti-seize to the striker.
DOOR GASKET: Periodically check gasket to make sure it is not overcompressed. If compressed, replace with a special woven Door Rope.
(Don’t try substituting rope, only use special Lennox Hearth Products
Door Rope).
PLATED ACCESSORIES: Clean only with household type glass cleaner
and a very soft cotton cloth. Other products may damage plated finish,
paint and gaskets.
BAFFLE BLANKET: Your baffle blanket should be inspected during every
chimney cleaning. If the baffle blanket is compressed or heavily stained,
it should be replaced. Heavy creosote stains or matting is an indication
of improper use and your burning habits should be reviewed.
GLASS CLEANING: Only clean glass with products specifically made to
use on wood stoves. Other products could damage gaskets and paint.
Never scrape glass with a razor blade. This can pit the glass and make it
impossible to clean in the future.
WINDOW GASKET: The window gasket can be checked by running the
flame of a match near the gasket and around the door. If the flame is
drawn in around the window, the gasket should be replaced.
DOOR HANDLE: Door handle may become tight as you use the stove.
Free the handle up by using dry graphite supplied with the stove. The
directions are included with the graphite.
WARNING
Inspect and clean chimney and connector frequently.
Under certain conditions of use, creosote buildup
may occur rapidly.
Cleaning Glass: Ensure appliance is cold prior
to cleaning glass. A commercial glass cleaner
designed for stoves is recommended. Do not use
abrasive cleaners. Do not clean with any materials,
which may scratch or otherwise damage the glass.
Scratches on the glass can develop into cracks or
break. Inspect the glass regularly. If you detect a
crack, extinguish the fire and contact your dealer
for a replacement.
GLASS REPLACEMENT INSTRUCTIONS
Step 1. Remove Door Assembly - Open door to remove E clip from the upper
hinge pin. Remove upper hinge pin by pulling up while holding the opposite side of the door. Lift door out of the lower hinge pin and place
face down on a soft surface.
Step 2. Remove Door Back Screws (6 ea.) - Using a 5/32” allen wrench remove
the 6 retainer screws from the faceplate. To locate screws, peel back the
door gasket as necessary.
Step 3. Disassemble Door Assembly - Flip door assembly over to be face up.
Separate faceplate from door back by pulling up on faceplate.
Step 4. Remove Glass - Carefully remove broken glass one piece at a time
(protective gloves are recommended)
Step 5. Install New Glass Assembly - Install the new glass with gasket in recess
on door back (use only factory supplied 5mm ceramic glass. Do not
substitute).
Step 6. Reinstall Faceplate and Screws - Reinstall faceplate onto door back
and while holding the door assembly together flip the assembly back
onto it’s face. Carefully reinstall the screws. Be very careful not to
overtighten the screws (this could result in glass breakage when the
stove or fireplace insert is hot) and it is highly recommended to use anti
seize on the screws.
Step 7. Reinstall Door - Set door assembly back into the lower hinge mount
while holding the handle side of the door up. Place the upper hinge
pin back in the mount and door assembly. Reinstall the E clip that was
removed.
GLASS CLEANING GUIDELINES
WARNING: DO NOT CLEAN GLASS WHEN APPLIANCE IS HOT!
Glass on any wood stove or fireplace insert will not stay perfectly clean.
Here are some guidelines for cleaning and caring for the glass:
• Ensure the stove or fireplace insert is cold prior to cleaning glass.
• This appliance is designed to provide a flow of air over the inside of
the glass, where along with high heat helps inhibit build-up on the
glass. When build-up occurs, a commercial glass cleaner designed
for stoves is recommended. Regular household glass cleaners will
not clean creosote.
• Do not use abrasives such as steel pads, steel wool or oven cleaner
as they will scratch the glass. Never scrape glass with a razor blade
as this may pit the glass and make it impossible to clean in the future.
• Do not use chemical glass cleaners as they may damage the gaskets
or painted surfaces.
TIPS FOR KEEPING THE GLASS CLEAN
• Burn only dry seasoned cord wood. Wet wood = Dirty glass.
• A short, hot fire (15 - 20 minutes) may help to clean off some of the
normal buildup. Lower burns = more build-up. Higher burns = less
build-up.
• Keep freshly loaded wood away from the glass.
• After reloading, allow all the wood to catch flame before dampering
down the stove or fireplace insert.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Door Gasket
Door Back
Glass
Figure 20
Faceplate
Screws and
Washers
Handle Rod
Glass Gasket
19
TROUBLESHOOTING
Problem Solution
POOR DRAFT: Extend chimney in length or have the chimney realigned to the proper size flue. Oversized chimneys normally have
poor drafts. Remember, the stoves’ draft depend solely on the natural draft of the chimney (See Draft Requirements on
Page 4). If your stove is not drafting properly, your chimney is the problem. All stoves are thoroughly tested to ensure
proper draft with the correct size chimney flue.
EXCESSIVE DRAFT: With better chimneys being more common, excessive draft can be an issue. Alleviate excessive draft by slowing the
burn rate of the stove once it has reached proper operating temperature (See Maximizing Your Stoves Overall Efficiency
on Page 18).
DIRTY GLASS: 1) Burn smaller, hotter fires and check to make sure you are not setting the draft down too far with the draft control.
2) Make sure your wood is well-seasoned and dry (not open to rain - see Creosote and Fuel sections on Page 5).
3) See Poor Draft section (above) and Cleaning Glass on Page 19 .
SMOKES WHEN 1) If smoke is entering the room, check to make sure your baffle boards are properly installed
DOOR IS OPEN: and that the baffle blanket is pushed back flush with the front of the baffle boards.
2) Check the chimney for blockage due to creosote (see Chimney and Creosote sections on Pages 5 and 6).
3) Check draft (See POOR DRAFT section above).
WOOD BURNS 1) The draft control must be closed further.
TOO FAST: 2) Add fuel at lower firebox temperatures.
3) Load wood side to side and reduce the flow of air under wood.
4) The door seal may need replacing, check for leakage.
5) See “Excessive Draft.”
POOR HEAT 1) Check your wood. Wet, moist, unseasoned wood will not produce heat.
OUTPUT: 2) Your stove needs to be seasoned (moisture removed from the steel and brick). Continue to burn a fire. It normally
takes from one to three weeks of burning to season your stove (See Burn-In Procedures on Page 5).
3) See Excessive Draft section above.
PAINT GIVES OFF Paint is tempering-in. Burn only moderately hot for the first few days until paint is fully cured.
ODOR (smoke): Then burn a very hot fire to cure any paint that may not easily cure. Open windows or door to ventilate (See Burn-In
Period on Page 5).
20
DO’S AND DON’TS
DO NOT: Install or operate this stove before reading this manual.
DO NOT: Close the draft beyond the point at which the flames are completely extinguished.
DO NOT: Open the stove door without fully opening the draft first.
DO NOT: Burn driftwood or wood that has been in salt water. This includes some mill ends and scrap lumber that has been floated in salt water on
the way to the mill. (This will void your warranty).
DO NOT: Handle the plated faceplate unnecessarily. Use the door handle only.
DO NOT: Force oversized logs into the firebox as this may dislodge the baffle assembly.
DO NOT: Close the door tightly during Burn-In Period.
DO: Be sure to clean any fingerprints from optional accessories that have plated surfaces before burning the appliance. Clean the plated
surfaces only with household type glass cleaner and a very soft cloth.
DO: Consult local building department if other than recommended clearances are desired.
DO: Read instructions for the baffle boards and baffle blanket occasionally to ensure you have not bumped or moved them out of place when
loading wood.
DO: Check the chimney and baffle monthly to make sure they are clean.
DO: Burn seasoned, dry wood only! (RAIN = WET WOOD)
DO: Open the door frequently during Burn-In Period to keep gasket from adhering to the curing paint.
DO: Enjoy the warm feeling of your new Lennox Hearth Products appliance.
21
REPLACEMENT PARTS - MODELS S160 AND SWS160
Contact an Lennox Hearth Products dealer to obtain any of these
parts. Never use substitute materials. Use of non-approved parts
can result in poor performance and safety hazards.
FRONT DOOR PARTS LIST
Item # Cat. No Description
1 H5639 Door Rope Kit, 7/8” Dia. (6’ 2”)
2 H5629 Upper Hinge Pin
3 H5626 Upper Hinge Pin E-Clip
4 H5628 Lower Hinge Pin
6 H5640 Glass Gasket Kit (8’ 4”)
7 H5577 Set of 6 screws and 6 washers for door assembly
H5654 Spring Handle / Nickel
8
H5653 Spring Handle / Gold
71067 Traditional Door Glass / Plain
71068 Traditional Door Glass / Sailboat
71063 Traditional Door Glass / Cattail
9
71065 Traditional Door Glass / Evergreen
71066 Traditional Door Glass / Floral
71057 Traditional Door Faceplate / Black
71058 Traditional Door Faceplate / Gold
10
71059 Traditional Door Faceplate / Nickel
71148 Traditional Door Faceplate / Brushed Gold
71145 Traditional Door Faceplate / Brushed Nickel
71072 Arch Door Glass / Plain
71073 Arch Door Glass / Sailboat
71069 Arch Door Glass / Cattail
11
71070 Arch Door Glass / Evergreen
71071 Arch Door Glass / Floral
71060 Arch Door Faceplate / Black
71061 Arch Door Faceplate / Gold
12
71062 Arch Door Faceplate / Nickel
71147 Arch Door Faceplate / Brushed Gold
71144 Arch Door Faceplate / Brushed Nickel
13 H5579 Traditional Door Back w/ Handle (door gasket included)
14 H5578 Arch Door Back w/ Handle (door gasket included)
ASH DRAWER PEDESTAL AND PEDESTAL
15 H5514 Small & Large Pedestal Rear Block Off Plate w/ Hole
16 H5557 Ash Drawer for Small Pedestal
17 H5564 Ash Plug Remover and Rake
18 H5516 Aluminum Flex Tubing Kit w/ clamp (15” of 4” dia.)
19 H5565 6” x 6-1/2” Rodent Screen
LEGS AND LEG PARTS
18 H5516 Aluminum Flex Tubing Kit w/ clamp (15” of 4” dia.)
20 H5558 Single Black Cascade Leg
H5669 Single Black Olympic Leg
H5622 Single Gold Olympic Leg
21
H5621 Single Nickel Olympic Leg
H5620 Single Brushed Gold Olympic Leg
H5619 Single Brushed Nickel Olympic Leg
22 H5649 Heatshield / Leg Fastener Kit
23 71110 Bottom Heatshield / S160 and SWS160
24 H5662 Cascade / Olympic Leg Kit Outside Air Plenum Box
FSB BLOWER PARTS
25 H8062 FSB700 Blower Only Assembly w/ blower wiring harness
26 H5658 Fan Blade (FSB700)
27 H5657 Fan Cage (FSB700)
28 H8063 FSB700 Blower Only Wire Harness
29 H8064 Snap Switch w/gasket and screws
30 H5742 Speed Control - High Temperature (FSB700)
31 H8065 Control Panel Assembly w/ Snap Switch Housing As-
32 H8066 Control Switch (Manual, Off, Automatic)
33 H5627 Removable Inner Flue Collar Ring
H8079 S160 Nameplate Kit w/ Hardware - Nickel
34
H8080 S160 Nameplate Kit w/ Hardware - Gold
35 H5650 Draft Rod Knob
36 H8081 Ash Block Off - Hearthplate
37 H5661 Cast Iron Ash Plug
38 H5582 1/2 Cut Brick for Ash Removal
39 H5612 Firebrick 4-1/2” x 9” (10 per stove)
40 H5576 Firebrick 4-1/4” x 9” (2 per stove)
41 H5607 Firebrick 2-1/4” x 9” (3 per stove)
42 H3095 Firebrick 2-1/4” x 8-7/8” (1 per stove)
43 H5604 Firebrick 1-1/2” x 9” (1 per stove)
44 H5597 Firebrick 1-1/2” x 8-7/8” (1 per stove)
45 H3104 Front Baffle/Secondary Burn Tube Assembly
46 H3105 Middle/Rear Baffle/Secondary Burn Tube Assembly
47 H3103 Complete Baffle/Secondary Burn Tube Assembly (in-
48 H8017 Baffle Blanket 20” x 11” x 1”
49 H8016 Baffle Board Kit w/ Baffle Blanket
71052 Dry Graphite (Apply to door handle and door hinges)
H5633 Anti Seize 2 gram pouch
sembly
S160 and SWS160 STOVE PARTS
(1 ea. Lennox & 1 ea. Country)
(1 ea. Lennox & 1 ea. Country)
cludes tubes and all mounting hardware)
MISCELLANEOUS PARTS
22
REPLACEMENT PARTS - MODELS S160 AND SWS160
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
23
REPLACEMENT PARTS - MODELS S160 AND SWS160
Door Parts
1
2
3
13
8
Blower Parts
1
5
2
3
14
4
5
8
4
9
6
7
10
11
6
7
12
25
27
28
31
30
26
29
24
32
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
REPLACEMENT PARTS - MODELS S160 AND SWS160
Leg and Leg Parts
20
22
23
24
18
21
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
25
REPLACEMENT PARTS - MODELS S160 AND SWS160
Ash Drawer Pedestal and Pedestal
15
18
19
17
16
15
18
19
26
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
ACCESSORIES - MODELS S160 AND SWS160
Product Reference Information
Cat. No. Description Ship.
Weight
H7884 S160T-B, Stove / Traditional Black Door /
Nickel Nameplate
H7883 S160A-B, Stove / Arch Black Door / Nickel
Nameplate
H8406 SWS160, Stove / Traditional Black Door 313 lb. 18.91 cu. ft.
313 lb. 18.91 cu. ft.
313 lb. 18.91 cu. ft.
PEDESTALS (REQUIRED)
Cat. No. Model Description
71108 WS-PED Pedestal (ref. form #506033-16)
71109 WS-PED-ASHD Ash Drawer Pedestal (ref. form #506033-15)
or LEGS (Required) (ref. form #506033-14)
70000 LEG-OLY-B Olympic Sculptured Black (4 per pkg.)
70001 LEG-OLY-G Olympic Sculptured Gold (4 per pkg.)
70002 LEG-OLY-N Olympic Sculptured Nickel (4 per pkg.)
70007 LEG-OLY-BRG Olympic Sculptured Brushed Gold
(4 per pkg.)
70008 LEG-OLY-BRN Olympic Sculptured Brushed Nickel
(4 per pkg.)
70003 LEG-CAS-B Cascade Steel Black (4 per pkg.)
HEAT SHIELD (REQUIRED WITH LEGS)
71110 WSHS-160 Heat Shield
(ref. form #506033-14)
FACEPLATE KITS (INCLUDES FACEPLATE, HANDLE AND NAMEPLATE)
H7901 ARCH-FPK-BG Arch Faceplate/Brushed Gold
H7902 TRAD-FPK-BG-SM Sm - Traditional Faceplate/Brushed Gold
H7904 ARCH-FPK-G Arch Faceplate/Gold
H7905 TRAD-FPK-G-SM Sm - Traditional Faceplate/Gold
BLOWER
H7917 BLWR-FSB700-SS Blower Kit, FS Woodstoves
OUTSIDE AIR KITS
71111 OUTAIRK-L Outside Air Kit / Leg
(ref. form #506033-18)
71112 OUTAIRK-P Outside Air Kit / Pedestal (ref. form #506033-17)
MISC.
71053 Paint Gold (1/2 Pint) Paint Gold (1/2 pint)
71054
Paint Nickel (1/2 Pint)
Paint Nickel (1/2 pint)
H8159 TSPK-B Touch-Up Paint , Metallic Black, 12 oz.
Aerosol
H5308 W-LEGF-LBRKT Leg Fastening L-Brackets (4 per pkg.) (Tie
down kit to be used in mobile or modular
(ref. form #506033-19)
homes)
Ship.
Volume
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
27
ACCESSORIES - MODELS S160 AND SWS160
Security Chimneys™ Pipe
Tubinox Components
6” Rigid Stainless Steel Liner
Cat. No. Model Description Pc. / Container
6LL6 6LL6 LENGTH 6” X 6” 4
6LL12 6LL12 LENGTH 6” X 12” 4
6LL24 6LL24 LENGTH 6” X 24” 4
6LL36 6LL36 LENGTH 6” X 36” 4
6LL48 6LL48 LENGTH 6” X 48” 4
6L7A 6L7A ADJUSTABLE LENGTH (7 to 11) 4
6LT 6LT SPLIT BASE TEE 4
6LTCS 6LTCS TEE CAP 10
6LTC 6LTC TWIST LOCK TEE CAP 4
6LE30 6LE30 ELBOW 30 DEGREE 4
6LE45 6LE45 ELBOW 45 DEGREE 4
6LE90 6LE90 ELBOW 90 DEGREE 4
6LST 6LST FLASHING 5
6LSTSS 6LSTSS FLASHING STAINLESS 1
6LSA 6LSA SUPPORT ASSEMBLY 5
6LSB 6LSB INTERIOR SUPPORT 5
6LAAM 6LAAM ADAPTOR FLEX PIPE (MALE) 4
6LAAF 6LAAF ADAPTOR FLEX PIPE (FEMALE) 4
6LLFLEX 6LLFLEX STAINLESS FLEXIBLE LENGTH
(6”X60”)
6LMA 6LMA MASONRY ADAPTOR 1
6LLR5 6LLR5 REDUCER LENGTH (6”-5”) 4
6LLW7 6LLW7 INCREASER LENGTH (6”-7”) 4
6LCC 6LCC DELUXE RAIN CAP 1
6LCS 6LCS REGULAR RAIN CAP 1
6LRSMI 6LRSMI ADJUSTABLE INSULATION
WALL THIMBLE 6” - 12”
4
1
Secure Black™ Single Wall Stove Pipe
6” SW Pipe and Accessories
Cat. No. Model Description Pc. / Container
6SWL6 6SWL6 LENGTH 6” X 6” 100
6SWL12 6SWL12 LENGTH 6” X 12” 5
6SWL24 6SWL24 LENGTH 6” X 24” 10
6SWL36 6SWL36 LENGTH 6” X 36” 2
6SWL48 6SWL48 LENGTH 6” X 48” 5
6SWLT 6SWLT TELESCOPIC LENGTH 6” (42”-
66”)
6SWLA 6SWLA ADJUSTABLE LENGTH 6”
(3”- 9”)
6SWMA 6SWMA SINGLE WALL MASONRY
ADAPTOR 6”
6SWT 6SWT TEE 6” (TEE CAP INCLUDED) 2
6SWE45 6SWE45 ELBOW 45 DEGREE 6” 4
6SWE90 6SWE90 ELBOW 90 DEGREE 6” 4
6SWE90A 6SWE90A SWIVEL 90 DEGREE ELBOW 6” 10
6UP 6UP FLUE EXTENSION 6” 10
6SWAB 6SWAB STOVE ADAPTOR 6” 8
6SWIN7 6SWIN7 INCREASER LENGTH ( 6”- 7”) 4
6SWIN8 6SWIN8 INCREASER LENGTH (6”- 8”) 4
6SWOA 6SWOA OVAL TO ROUND ADAPTOR 6” 5
6SWLK 6SWLK DAMPER UNIT 6” 4
6PB 6PB DECORATIVE COLLAR 6”
(ASHT)
6PF 6PF TRIM COLLAR 6” (ASHT) 5
1
5
1
25
Double Wall Black Stove Pipe
6” DL Pipe and Accessories
Cat. No. Model Description Pc. / Container
6DL6 6DL6 LENGTH 6” X 6” 8
6DL12 6DL12 LENGTH 6” X 12” 4
6DL24 6DL24 LENGTH 6” X 24” 2
6DL36 6DL36 LENGTH 6” X 36” 2
6DL42A 6DL42A TELESCOPIC LENGTH (42” 66”) 1
6DL3A 6DL3A ADJUSTABLE LENGTH (3”- 9”) 4
6DL36A 6DL36A ADJUSTABLE LENGTH ( 3”-34”) 2
6DT 6DT TEE (TEE CAP INCLUDED) 4
6DE45 6DE45 ELBOW 45 DEGREE 4
6DE90 6DE90 ELBOW 90 DEGREE 4
6DMA 6DMA MASONRY ADAPTOR 1
6UP 6UP FLUE EXTENSION 10
6DAB 6DAB STOVE ADAPTOR 8
6DLW7 6DLW7 INCREASER LENGTH ( 6”- 7”) 4
6DLW8 6DLW8 INCREASER LENGTH (6”- 8”) 4
6DLK 6DLK DAMPER UNIT DL 6” 4
6DQDH 6DQDH DECORATIVE COLLAR 25
6DQ 6DQ TRIM COLLAR 10
28
ACCESSORIES - MODELS S160 AND SWS160
Secure Temp® Factory-Built Chimney
6” Secure Temp ASHT and Secure Temp G-ASHT
Cat. No. Model Description Pc. / Container
Lengths and Fittings
6L8 6L8 LENGTH 6” X 8” 1
6L12 6L12 LENGTH 6” X 12” 1
6L18 6L18 LENGTH 6” X 18” 1
6L24 6L24 LENGTH 6” X 24” 1
6L36 6L36 LENGTH 6” X 36” 1
6L48 6L48 LENGTH 6” X 48” 1
6LA 6LA ADJUSTABLE LENGTH, 12” 1
6TI 6TI INSULATED TEE (TCS INCLUDED) 1
6TCS 6TCS INSULATED SS TEE CAP (INCLUDED
WITH TI)
6TB 6TB BASE TEE GALVANIZED (TC IN-
CLUDED)
6TBS 6TBS BASE TEE STAINLESS (TCS IN-
CLUDED)
6TBD 6TBD BASE TEE GALVANIZED DOUBLE (TC
INCLUDED)
6TC 6TC BASE TEE CAP GALVANIZED 10
6TCI 6TCI INSULATED TEE CAP (USE WITH
SME SUPPORT)
6TCP 6TCP DRAIN TEE CAP (USE WITH SME
SUPPORT)
6E15 6E15 INSULATED ELBOW 15 DEGREE 2
6E30 6E30 INSULATED ELBOW 30 DEGREE 1
Aluminum Zinc Coated Steel (Lengths and Fittings)
6GL8 6GL8 LENGTH 6” X 8” 1
6GL12 6GL12 LENGTH 6” X 12” 1
6GL18 6GL18 LENGTH 6” X 18” 1
6GL24 6GL24 LENGTH 6” X 24” 1
6GL36 6GL36 LENGTH 6” X 36” 1
6GL48 6GL48 LENGTH 6” X 48” 1
6GLA 6GLA ADJUSTABLE LENGTH, 12” 1
6GTI 6GTI INSULATED TEE (TCS INCLUDED) 1
6TCS 6TCS INSULATED SS TEE CAP (INCLUDED
WITH GTI)
6GE15 6GE15 INSULATED ELBOW 15 DEGREE 2
6GE30 6GE30 INSULATED ELBOW ALUM-ZINC 30
DEGREE
Supports
6UP 6UP FLUE EXTENSION 10
PS PS SQUARE CATHEDRAL SUPPORT
EXTENSION
6SSC 6SSC SQUARE CATHEDRAL SUPPORT W/
COUPLER
6SSAC 6SSAC ADJUSTABLE SQUARE CATHEDRAL
SUPPORT w/COUPLER
6SFC 6SFC FINISHING SUPPORT W/COUPLER 1
10
1
1
1
5
5
10
1
1
1
1
Cat. No. Model Description Pc. / Container
Supports (continued)
6SM 6SM TEE SUPPORT 1
6SMA 6SMA GALVALUME ADJUSTABLE TEE
SUPPORT (2” TO 6”)
SO SO OFFSET SUPPORT / WALL SUP-
PORT
ST ST ROOF SUPPORT 10
6SD 6SD FLOOR SUPPORT 5
6SP 6SP ANCHOR PLATE 10
Braces and Firestops
6BF 6BF FIRESTOP 10
6RSM30 6RSM30 ANGLED FIRESTOP - 30 DEGREE
6RS 6RS RADIATION SHIELD 5
6RSA2 6RSA2 2PC INSULATED ATTIC RADIATION
SHIELD
6ARSA 6ARSA ADJUSTABLE INSULATED ATTIC
RADIATION SHIELD
6RSI 6RSI INSULATED RADIATION SHIELD 1
6RSM 6RSM INSULATED WALL THIMBLE 1
6RSMI30 6RSMI30 30-DEGREE RADIATION SHIELD 1
BS2 BS2 UNIVERSAL ROOF BRACE 1
BM BM UNIVERSAL WALL BAND 10
6BH 6BH GUY WIRE BAND (WIRE NOT
INCLUDED)
6FR 6FR FLAT ROOF FLASHING 3
6FAR 6FAR ADJUSTABLE ROOF FLASHING -
1/12- 7/12
6FARA 6FARA ADJUSTABLE MALLEABLE ALUMI-
NUM ROOF FLASHING 1/12 - 7/12
6FBR 6FBR ADJUSTABLE ROOF FLASHING -
8/12- 12/12
6FBRA 6FBRA ADJUSTABLE MALLEABLE ALUMI-
NUM ROOF FLASHING 8/12 - 12/12
6FBBR 6FBBR ADJUSTABLE ROOF FLASHING
12/12 - 21/12
6FPR 6FPR PEAK ROOF FLASHING 1/12 -7/12 3
6FPBR 6FPBR PEAK ROOF FLASHING 8/12 -12/12 3
6FC 6FC STORM COLLAR 10
Chimney Termination
6CC 6CC RAIN CAP 1
PE PE UNIVERSAL SPARK ARRESTER
BAND
Chimney Accessories
6PF 6PF DECORATIVE TRIM 5
6PB 6PB DECORATIVE COLLAR 25
6PA 6PA BLACK PIPE ADAPTOR 1
6PD 6PD FINISHING CONE 1
Fireplace Components
6EK-1 6EK-1 EXTERIOR KIT (INCLUDES 1 TI, 1
TCI, 1 SME, 1 RSM, 1 CC, 1 PB,
1 BM)
6IK 6IK INTERIOR KIT (INCLUDES 1 SFC, 1
RSA2, 1CC)
5
10
1
1
10
3
3
3
10
1
1
29
SAFETY / LISTING LABEL - ENGLISH
30
2011 2012 2013
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
SAFETY / LISTING LABEL - FRENCH
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
31
WARRANTY
Your wood appliance is covered by a limited warranty (provided with the
appliance). Please read the warranty to be familiar with its coverage.
3. The part number.
4. The description of the part.
5. The quantity required.
6. The installation date of the appliance.
Retain this manual. File it with your other documents for future reference.
REPLACEMENT PARTS
See Page 22 for a complete replacement parts list. Use only parts supplied from the manufacturer.
Normally, all parts should be ordered through your Lennox distributor or
dealer. Parts will be shipped at prevailing prices at time of order.
When ordering repair parts, always give the following information:
1. The model number of the appliance.
2. The serial number of the appliance.
Your Appliance’s Model Number _______________________________________
Your Appliance’s Serial Number ________________________________________
The Date On Which Your Appliance Was Installed __________________________
If you encounter any problems or have any questions concerning the
installation or application of this system, please contact your dealer.
LENNOX HEARTH PRODUCTS
1508 Elm Hill Pike, Suite 108
Nashville, TN 37210
visit us at www.Lennox.com
1-800-9-LENNOX
PRODUCT REFERENCE INFORMATION
We recommend that you record the following important information about
your appliance. If you did not purchase your appliance directly from a
Lennox Hearth Products dealer, then please call 1-800-9-LENNOX for the
name and phone number of your nearest Lennox Hearth Products dealer
who will answer your questions or address your concerns.
Your Dealer's Name _________________________________________________
Lennox Hearth Products reserves the right to make changes at any time, without notice, in
design, materials, specifications, prices and also to discontinue colors, styles and products.
Consult your local distributor for fireplace code information.
Printed in U.S.A. © 2007 by Lennox Hearth Products
P/N 775214M Rev. F 09/2011
32
1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210
Loading...