Lennox RG35A/BGEF, RG35A2/BGCEF, RG35A1/BGEF, RG35A1/BGCEF, RG35B/BGE Owner's Manual

OWNER’S MANUAL

FOR THE

AIR CONDITIONER

REMOTE CONTROLLER

Before using your air conditioner, please
read this manual carefully and keep it for
future reference.

Australia 13 23 50 New Zealand 0800 653 330

Web www.lennoxaus.com.au

NOTE:

This remote controller will only function
with the following Lennox inverter models –

LNIV2610
LNIV3510
LNIV5010
LNIV6510

Read this manual

Inside you will fi nd many helpful hints on how to use
and maintain your air conditioner properly. Just a little
preventative care on your part can save you a great deal
of time and money over the life of your air conditioner.
You’ll fi nd many answers to common problems in the
chart of troubleshooting tips. If you review the chart of
Troubleshooting Tips fi rst, you may not need to call for
service.

Congratulations on your purchase
of a Lennox air conditioner

E963_Lennox AC Remote Controller 16pp A5_3.indd 16-1E963_Lennox AC Remote Controller 16pp A5_3.indd 16-1 23/01/12 9:27 AM23/01/12 9:27 AM

2 3

CONTENTS HANDLING THE REMOTE CONTROLLER

HANDLING THE REMOTE CONTROLLER .......... 3

Location of the remote controller ........................ 3

Replacing batteries ...........................................3

REMOTE CONTROLLER SPECIFICATIONS .......4

PERFORMANCE FEATURES .............................. 4

FUNCTION BUTTONS ....................................... 6

INDICATORS ON LCD ...................................... 9

HOW TO USE THE BUTTONS .........................10

Auto operation ................................................ 10

Cooling/Heating/Fan operation ......................... 10

Dehumidifying operation .................................. 11

Adjusting air fl ow direction ............................... 11

Timer operation ..............................................12

SLEEP / FRESH function ..................................15

LED / FOLLOW ME function ............................. 15

TURBO / SELF-CLEAN function ........................15

Location of the remote controller

• Use the remote controller within a distance of 8 metres
from the appliance, pointing it towards the receiver.
Reception is confi rmed by a beep.

Replacing batteries

NOTE: Replace the batteries when there is no receiving beep

from the indoor unit or if the transmission indicator on the
remote controller fails to light.

The remote controller is powered by two dry cell batteries
(R03/LR03X2) housed in the rear part and protected by a
cover.

(1) Remove the cover by pressing and sliding it off.

(2) Remove the old batteries and insert the new batteries,

placing the (+) and (-) ends correctly.

(3) Re-attach the cover by sliding it back into position.

NOTE: When the batteries are removed, the remote
controller erases all programming. After inserting new
batteries, the remote controller must be reprogrammed.

CAUTION

• The air conditioner will not operate if curtains, doors
or other materials block the signals from the remote
controller to the indoor unit.

• Prevent any liquid from falling into the remote
controller. Do not expose the remote controller to
direct sunlight or heat.

• If the infrared signal receiver on the indoor unit is
exposed to direct sunlight, the air conditioner may
not function properly. Use curtains to prevent the
sunlight from falling on the receiver.

• If other electrical appliances react to the remote
controller. either move these appliances or consult
your local dealer.

CAUTION

• Do not mix old and new batteries or batteries of
different types.

• Do not leave the batteries in the remote controller if
they are not going to be used for 2 or 3 months.

• Do not dispose batteries as unsorted municipal
waste. Collection of such waste separately for special
treatment is necessary.

8m

The design and specifi cations are subject to change without
prior notice for product improvement. Consult with the sales
agency or manufacturer for details

E963_Lennox AC Remote Controller 16pp A5_3.indd 2-3E963_Lennox AC Remote Controller 16pp A5_3.indd 2-3 23/01/12 9:27 AM23/01/12 9:27 AM

4 5

REMOTE CONTROLLER SPECIFICATIONS

PERFORMANCE FEATURES

PERFORMANCE FEATURES

Model

RG35A(2)/BG(C)EF, RG35A1/BG(C)EF, RG35B/BG(C)E, RG35C/BG(C)E,
RG36A(1)/BG(C)EF, RG36A2/BG(C)EF, RG36B(1)/BG(C)E, RG36C/BG(C)E

Rated Voltage

3.0V (Dry cell batteries R03/LR03 x 2)

Signal Receiving Range

8m (when using 3.0 voltage, up to 11m)

Environment

-5ºC ~ 60ºC

1. Operating Mode: AUTO, COOL, DRY, HEAT (Cooling only model without), and FAN.

2. Timer Setting Function in 24 hours.

3. Indoor Setting Temperature Range : 17ºC~30ºC.

4. Full function of LCD (Liquid Crystal Display).

NOTE: There is only a slight difference in appearance
between the RG35 series and RG36 series. The operations
and functions of the buttons are the same. Some buttons
have two functions, some buttons have only one function,
for example

SLEEP
FRESH

and

SLEEP

.

Please refer to the above illustrations for details.

RG35A(2)/BG(C)EF

RG35B/BG(C)E

RG35C/BG(C)E

MODE MODE

MODE

SWING SWI NG

SWING

TEMP TEMP

TEMP

SHORTCUT SHORTCUT

SHO RTCUT

FA N

SPE ED

FAN

SPEED

FAN

SPEED

TIMER

OF F

TI MER

OFF

TIMER

OFF

RESET RE SET

RE SE T

LOCK LOC K

LOCK

LED

FOL LOW ME

LED

TIMER

ON

TIME R

ON

TIMER

ON

TURBO

SELF CL EAN

TURB O

DIRE CT DI REC T

DIRECT

SLEEP
FRESH

SLEEP

SLEEP

MODE

SWING

TEMP

SHORTCUT

FAN

SPEE D

TIM ER

OFF

RESET LOCK

LED

FOL LOW ME

TIMER

ON

DIRE CT

SLEEP

RG35A1/BGEF

TURBO

FP

RG36A(1)/BG(C)EF

RG36A2/BG(C)EF RG36C/BG(C)E

TUR BO

SELF

CLEAN

TURBO

SLEEP
FRESH

SLEEP

SLEEP

SHORT

CUT

SHORT

CUT

SHORT

CUT

TIMER

ON

TIMER

ON

TIMER

ON

TIMER

OFF

TIM ER

OFF

TIMER

OFF

LOCK

LOCK

LOCKRESE T

RESET

RESE T

LED

FOLLOW

ME

LED

FAN

SPEED

FAN

SPEED

FAN

SPEED

DIRECT

DIRECT

DIRECT

SWING

SWING

SWING

MODE

MODE

MODE

TEMP

TEMP

TEMP

SLEEP

SHORT

CUT

TI MER

ON

TIMER

OFF

LOCK

RESET

LED

FAN

SPEED

DIRECT

SWING

MODE

TE MP

RG36B(1)/BG(C)E

TURBO

FP

ON/OFF

ON/OFF

ON/OFF

ON/OFF

Models of RG36B/BG(C)E do
not have FP function.

E963_Lennox AC Remote Controller 20pp A5_1c.indd 4-5E963_Lennox AC Remote Controller 20pp A5_1c.indd 4-5 13/12/11 4:56 PM13/12/11 4:56 PM

6 7

FUNCTION BUTTONS FUNCTION BUTTONS

UP Button (+)

Press this button to increase setting temperature or to
increase the Hour setting during Timer setting.

DOWN Button (-)

Press this button to decrease setting temperature or to
decrease the Hour setting during Timer setting.

SHORTCUT (MEMORY SHORTCUT) Button

• Used to restore the current settings or restore previous
settings.

• On the fi rst time connecting to power, if the SHORTCUT
button is pressed, the unit will operate on AUTO mode,
24°C, and fan speed will be set to Auto.

• Pressing this button whilst the remote controller is on,
the system will automatically revert back to the previous
settings including operating mode, setting temperature,
fan speed level and sleep feature (if activated).

• Pressing this button whilst the remote controller is off,
the system will only resume the previous settings and
will not transmit the signals to the unit. The sleep feature
is disabled.

• If pressing for more than 2 seconds, the system will
automatically restore the current operation settings
including operating mode, setting temperature, fan speed
level and sleep feature (if activated).

FAN SPEED Button

Used to select the fan speed in four steps:

AUTO LOW MED HIGH

TIMER ON Button

Pressing this button will initiate the auto-on time sequence.
Each press will increase the auto-timed setting in 30
minutes increments.

When the setting time displays 10H, each press will increase
the auto-timed setting in 60 minute increments. To cancel
the auto-timed program, simply adjust the auto-on time to
0:0.

ON/OFF Button (

ON/OFF

)

Operation starts when this button is pressed and stops when
this button is pressed again.

MODE Button

Each time the button is pressed, the operation mode is
selected in the following sequence:

AUTO COOL DRY HEAT FAN

NOTE: Heat mode is for Cooling & Heating models only.

SWING Button

Used to stop or start horizontal louvre auto swing feature.

DIRECT Button

Used to change the louvre movement and set the desired up/
down air fl ow direction. The louvre changes 6º in angle for
each button press.

SLEEP/FRESH Button

Active/Disable SLEEP function. If pressing for more than 2
seconds, the FRESH function will be activated. Pressing for
more than 2 seconds again will disable it.

NOTE: While the unit is running under SLEEP mode, it would
be cancelled if the MODE, FAN SPEED or ON/OFF buttons
are pressed.

TURBO/SELF-CLEAN (or FP) Button:

Active/Disable TURBO function. If pressing for more than
2 seconds, the SELF-CLEAN function will be activated.
Pressing for more than 2 seconds again to disable
(depending on model). During the heating operation (only
when the setting mode is HEAT), press this button and the
unit will operate at a setting temperature of 8°C.The display
window of indoor unit will display FP. Pressing ON/OFF,
SLEEP, FP, MODE, FAN SPEED, UP, DOWN and SHORTCUT
while operating will cancel the FP function.

RESET Button:

When you press the recessed RESET button, all current
settings are cancelled and the control will return to the initial
settings.

1

2

4

5

3

8

10

9

6

7

11
12
13

14

15

MODE

SWING TEMP

SHORTCUT

FAN

SPEED

TIMER

OFF

RESET LOCK

LED

FOLLOWME

TIMER

ON

TURBO

SELFC LEAN

DIRECT

SLEEP
FRESH

RG35A(2)

1

2

4

5

3

8

10

9

6

7

11
12
13

14

15

MODE

SWING

TEMP

SHORTCUT

FAN

SPEED

TIMER

OFF

RESET LOCK

LED

FOLLOWME

TIMER

ON

TURBO

FP

DIRECT

SLEE P

RG35A 1

1

2

4

5

3

9

10

8

6

7

11

12

13

14

15

TU RBO

SELF

CLEAN

SLEEP
FRESH

SHORT

CUT

TIMER

ON

TIMER

OFF

LOCK

RESET

LED

FOLLOW

ME

FAN

SPEED

DIR ECT

SWING

MOD E

TEMP

RG36A(1)

1

2

4

5

3

9

10

8

6

7

11

12

13

14

15

TURBO

FP

SLEEP

SHORT

CUT

TIMER

ON

TIMER

OFF

LOCK

RESET

LED

FAN

SPEED

DIR ECT

SWING

MOD E

TEMP

RG36B1

ON/OFF

ON/OFF

2 9

10

11

12

3

4

5

6

7

1 8

E963_Lennox AC Remote Controller 20pp A5_1c.indd 6-7E963_Lennox AC Remote Controller 20pp A5_1c.indd 6-7 13/12/11 4:56 PM13/12/11 4:56 PM

8 9

FUNCTION BUTTONS (continued) INDICATORS ON LCD

TIMER OFF Button

Press this button to initiate the auto-off time sequence.
Each press will increase the auto-timed setting in 30 minute
increments.When the setting time displays 10H, each press
will increase the auto-timed setting in 60 minute increments.
To cancel the auto-timed program, simply adjust the auto-off
time to 0:0

LED/FOLLOW ME Button

Disable/Active indoor screen Display. When pressing for
more than 2 seconds, the FOLLOW ME function will be
activated. Pressing for more than 2 seconds again will
disable it.

LOCK Button

When you press the recessed LOCK button, all current
settings are locked in and the remote controller does not
accept any operation except that of the LOCK. Press again to
cancel the LOCK mode.

NOTE:

• Button designs shown may be slightly different from
the actual one you purchased depending on individual
models.

• All the functions described above are related to the
indoor unit. If the indoor unit does not have this feature,
then nothing will happen when that button on the remote
controller is pressed.

Transmission Indicator

This transmission indicator lights when remote controller
transmits signals to the indoor unit.

Mode display

Displays the current operation mode. Including auto ( ),
cool (

), dry ( ), heat ( ) (Not applicable to cooling only

models), fan (

) and back to auto ( ).

Temp./Timer display

Displays the temperature setting (17ºC~30ºC). When you
set the operating mode to FAN, no temperature setting is
displayed. In the TIMER mode, display shows the ON and
OFF settings of the TIMER.

Fan speed display

Displays the selected fan speed, AUTO (no display) and three
fan speed levels “

” (LOW) “ ” (MED) “ ”(HIGH) can be
indicated. The fan speed is AUTO when the operating mode
is either AUTO or DRY.

ON/OFF display

Displayed by pressing the ON/OFF button once.

Press the ON/OFF button again to remove.

Lock Display

Displayed when LOCK mode is activated.

FOLLOW ME Display

Displayed when FOLLOW ME function is activated.

Sleep Display

Displayed under sleeping operation.

Press the SLEEP button again to remove.

NOTE:

All indicators shown in the fi gure are for the purpose of clear
presentation. During the actual operation only the relative
functional signs are shown on the display window.

1

2

4

5

3

9

10

8

6

7

11

12

13

14

15

TURB O

SELF

CLE AN

SLEEP
FRESH

SHORT

CUT

TIM ER

ON

TIMER

OFF

LOC K

RESET

LED

FOLL OW

ME

FAN

SPEED

DIRECT

SWING

MODE

TEMP

ON/O FF

13

14

15

auto cool dry heat fan

sleep follow me lock run

SET TEMP. TIMER ONOFF

E963_Lennox AC Remote Controller 20pp A5_1c.indd 8-9E963_Lennox AC Remote Controller 20pp A5_1c.indd 8-9 13/12/11 4:56 PM13/12/11 4:56 PM

10 11

Dehumidifying operation

Ensure the unit is plugged in and power is on. The
OPERATION indicator on the display panel of the indoor unit
starts fl ashing.

1. Press the MODE button to select DRY mode.

2. Press the UP/DOWN buttons to set the desired

temperature. The temperature can be set within a range
of 17ºC~ 30ºC in 1ºC increments.

3. Press the ON/OFF button to start the air conditioner.

NOTE:

In the Dehumidifying mode, you cannot change the fan
speed. It has already been automatically controlled.

Adjusting air fl ow direction

Use the SWING and DIRECT button to adjust the desired
airfl ow direction.

1. When pressing the DIRECT button, the horizontal louvre

changes 6 degree in angle for each press.

2. When pressing the SWING button, the louvre will swing

up and down automatically.

NOTE:

When the louvre swings or moves to a position which would
affect the cooling or heating effect of the air conditioner, it
will automatically change the swing/moving direction.

HOW TO USE THE BUTTONS HOW TO USE THE BUTTONS

Auto operation

Ensure the unit is plugged in and power is on. The
OPERATION indicator on the display panel of the indoor unit
starts fl ashing.

1. Press the MODE button to select Auto.

2. Press the UP/DOWN button to set the desired
temperature. The temperature can be set within a range
of 17ºC~ 30ºC in 1ºC increments.

3. Press the ON/OFF button to start the air conditioner.

NOTE:

1. In the Auto mode, the air conditioner can logically choose
the mode of Cooling, Fan, and Heating by sensing the
difference between the actual ambient room temperature
and the setting temperature on the remote controller.

2. In the Auto mode, you cannot change the fan speed. It
has already been automatically controlled.

3. If the Auto mode is not comfortable, the desired mode
can be selected manually.

Cooling /Heating/Fan operation

Ensure the unit is plugged in and power is on.

1. Press the MODE button to select COOL, HEAT (cooling &
heating models only) or FAN mode.

2. Press the UP/DOWN buttons to set the desired
temperature.

3. Press the FAN button to select the fan speed in four
steps - Auto, Low, Med, or High.

4. Press the ON/OFF button to start the air conditioner.

NOTE:

In the FAN mode, the setting temperature is not displayed
in the remote controller and you are not able to control the
room temperature either. In this case, only steps 1, 3 and 4
may be performed.

3

1

2

2

MODE

SWING TEMP

SHORTCUT

FAN

SP EED

TIMER

OFF

RES ET LO CK

LED

FOLLOWME

TIME R

ON

TURBO

SELFCL EAN

DIRECT

SLEEP
FRESH

3

1

2

2

MODE

SWING TEMP

SHORTCUT

FAN

SPEED

TIMER

OFF

RESET LOC K

LED

FOLLOWME

TIMER

ON

TURBO

SELFCL EAN

DIRECT

SLEEP
FRESH

4

1

2

2

MODE

SWING

TEM P

SHORTCUT

FAN

SP EED

TIMER

OFF

RES ET LO CK

LED

FOLLOWME

TIME R

ON

TURBO

SELFCL EAN

DIRECT

SLEEP
FRESH

3

E963_Lennox AC Remote Controller 20pp A5_1d.indd 10-11E963_Lennox AC Remote Controller 20pp A5_1d.indd 10-11 14/12/11 11:57 AM14/12/11 11:57 AM

12 13

HOW TO USE THE BUTTONS HOW TO USE THE BUTTONS

Timer operation

Press the TIMER ON button can set the auto-on time of the
unit. Press the TIMER OFF button can set the auto-off time
of the unit.

To set the Auto-on time

1. Press the TIMER ON button. The remote controller shows
TIMER ON, the last Auto-on setting time and the signal
“h” will be shown on the LCD display area. Now it is
ready to reset the Auto-on time to START the operation.

2. Push the TIMER ON button again to set desired Auto-on
time. Each time you press the button, the time increases
by half an hour between 0 and 10 hours and by one hour
between 10 and 24 hours.

3. After setting the TIMER ON there will be a one second
delay before the remote controller transmits the signal
to the air conditioner. Then, after approximately another
2 seconds, the signal “h” will disappear and the set
temperature will re-appear on the LCD display window.

To set the Auto-off time

1. Press the TIMER OFF button. The remote controller
shows TIMER OFF, the last Auto-off setting time and the
signal “h” will be shown on the LCD display area. Now it
is ready to reset the Auto-off time to stop the operation.

2. Push the TIMER OFF button again to set desired Auto-off
time. Each time you press the button, the time increases
by half an hour between 0 and 10 hours and by one hour
between 10 and 24 hours.

3. After setting the TIMER OFF there will be a one second
delay before the remote controller transmits the signal
to the air conditioner. Then, after approximately another
2 seconds, the signal “h” will disappear and the set
temperature will re-appear on the LCD display window.

1

2

MODE

SWING

TEMP

SHORTCUT

FAN

SPEED

TIMER

OFF

RESE T LOC K

LED

FOLLOWME

TIMER

ON

TURBO

SELFCLEAN

DIRECT

SLEEP
FRESH

CAUTION

The effective operation time set by the remote controller for the timer function is limited to the following settings: 0.5, 1.0,

1.5, 2.0, 2.5, 3.0, 3.5, 4.0, 4.5, 5.0, 5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0, 9.5, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20,
21, 22, 23 and 24.

Example of Timer Setting

Start

Off

6hourslater

TIMERON

TIMER OFF

Stop

On

Set 10 hours l ater

TIMER OFF (Auto-off Operation)

The TIMER OFF feature is useful when you want the unit to
turn off automatically after you go to bed. The air conditioner
will stop automatically at the set time.

Example:

To stop the air conditioner in 10 hours;

1. Press the TIMER OFF button, the last setting of stopping
operation time and the signal “h” will show on the display
area.

2. Press the TIMER OFF button to display “10h” on the
TIMER OFF display of the remote controller.

3. Wait for 3 seconds and the digital display area will
show the temperature again. The “TIMER OFF” indicator
remains on and this function is activated.

TIMER ON (Auto-on Operation)

The TIMER ON feature is useful when you want the unit
to turn on automatically before you return home. The air
conditioner will automatically start operating at the set time.

Example:

To start the air conditioner in 6 hours.

1. Press the TIMER ON button, the last setting of starting
operation time and the signal

2. Press the TIMER ON button to display “6:0h” on the
TIMER ON display of the remote controller.

3. Wait for 3 seconds and the digital display area will show
the temperature again. The“TIMER ON” indicator remains
on and this function is activated

E963_Lennox AC Remote Controller 20pp A5_1c.indd 12-13E963_Lennox AC Remote Controller 20pp A5_1c.indd 12-13 13/12/11 4:56 PM13/12/11 4:56 PM

14 15

HOW TO USE THE BUTTONS HOW TO USE THE BUTTONS

SLEEP / FRESH function

• Pressing this button for less than 2 seconds will initiate the
SLEEP function. Keep pressing this button for more than 2
seconds and the FRESH function is initiated.

• The sleep function enables the unit to automatically increase
(cooling) or decrease (heating) by 1ºC per hour for the fi rst
two hours, then hold steady for the next 5 hours. After that
the unit will cease operation. It is able to maintain the most
comfortable temperature and save energy.

NOTE: The SLEEP function is only available under Cooling,
Heating and AUTO operations.

• When the FRESH function is initiated, the Ionizer/Plasma Dust
Collector (depending on models) is energized and will help to
remove pollen and impurities from the air.

Example of Timer Setting

TIMER ON OFF

On

Stop

2hourslater
after settin g

Set

Start

10 hours later
after setting

Off

Stop

Start

2hourslater
after setting

5hourslater
after setting

Set

TIMER ON OFF

COMBINED TIMER
(Setting both ON and OFF timers simultaneously)

TIMER OFF

TIMER ON

(On

Stop

Start operation)

This feature is useful when you want to stop the air
conditioner after you go to bed, and start it again in the
morning when you wake up or when you return home.

Example:

To stop the air conditioner 2 hours after setting and start it
again 10 hours after setting.

1. Press the TIMER OFF button.

2. Press the TIMER OFF button again to display 2.0h on the
TIMER OFF display.

3. Press the TIMER ON button.

4. Press the TIMER ON button again to display 10h on the
TIMER ON display

5. Wait for 3 seconds and the digital display area will show
the temperature again. The “TIMER ON OFF” indicator
remains on and this function is activated.

TIMER ON TIMER OFF

(Off

Start

Stop operation)

This feature is useful when you want to start the air
conditioner before you wake up and stop it after you leave
the house.

Example:

To start the air conditioner 2 hours after setting, and stop it 5
hours after setting.

1. Press the TIMER ON button.

2. Press the TIMER ON button again to display 2.0h on the
TIMER ON display.

3. Press the TIMER OFF button.

4. Press the TIMER OFF button again to display 5.0h on the
TIMER OFF display .

5. Wait for 3 seconds and the digital display area will show
the temperature again. The “TIMER ON OFF” indicator
remains on and this function is activated.

NOTE: The timer setting (TIMER ON or TIMER OFF) that in
sequence occurs directly after the set time will be activated
fi rst.

1

MOD E

SWI NG

TEMP

SHORTCUT

FAN

SPEE D

TIMER

OFF

RESET LOCK

LED

FOLLOWME

TIMER

ON

TURBO

SELF CLEAN

DIR ECT

SLEEP
FRES H

1

2

MODE

SWING

TEMP

SHORTCUT

FAN

SPEED

TIMER

OFF

RESET LOCK

LED

FOLLOW ME

TIMER

ON

TURBO

SEL F CLE AN

DIRECT

SLEEP
FRESH

LED / FOLLOW ME function

• Pressing this button for less than 2 seconds will initiate LED
function. Keep pressing this button for more than 2 seconds
and the FOLLOW ME function is initiated.

• When the FOLLOW ME function is activated, the remote
display is actual temperature at its location. The remote
control will send this signal to the air conditioner every 3
minutes until the FOLLOW ME button is pressed again.

• The FOLLOW ME function is not available under DRY and FAN
mode.

• Switching the operation mode or turning off the unit will
cancel the FOLLOW ME function automatically.

TURBO / SELF-CLEAN function

• Pressing this button for less than 2 seconds will initiate
TURBO function. Pressing this button for more than 2
seconds, the SELF-CLEAN function is initiated.

• Turbo function enables the unit to reach the preset
temperature in the shortest possible time. When pressing
this button on cooling mode, the unit will blow strong cooling
air with super high fan speed. When pressing this button on
heating mode (applicable to the unit adopts PTC only), the
PTC will be energized and bring fast heating operation.

• Under SELF-CLEAN mode, the air conditioner will
automatically clean and dry the evaporator keeping it as
fresh for the next operation.

1

2

E963_Lennox AC Remote Controller 16pp A5_2.indd 14-15E963_Lennox AC Remote Controller 16pp A5_2.indd 14-15 21/12/11 10:07 AM21/12/11 10:07 AM