Lennox MPB-40 User Manual

LENNOX HEARTH PRODUCTS

KITS AND ACCESSORIES

INSTALLATION INSTRUCTIONS FOR DECORATIVE ARCH SCREEN PANEL KIT

FOR USE WITH LMDV-33/35/40, MPD-33/35/40, MPB-35/40, SSDV-35/40, SSBV-35/40,

MPD35ST, MPB35ST, EDV-4035, EDVST AND EBVST GAS FIREPLACES

DECORATIVE ARCH SCREEN PANEL KIT

CAT# MODEL DESCRIPTION

H3592 DASPK33TI 33” Decorative Arch Screen Panel

H3593 DASPK35TI 35” Decorative Arch Screen Panel

H3594 DASPK40TI 40” Decorative Arch Screen Panel

Table 1

KIT CONTENTS

QUANTITY DESCRIPTION

1 ea Arched Doorframe Assembly

1 ea. Instruction Sheet

Table 2

750,199M REV. A 04/2006

DECORATIVE ARCH SCREEN PANEL KIT

WARNINGS

Hot! Do not touch! These decorative screen doors are NOT heat guards. behind the screens will be hot during operation and will retain heat for a while after shutting off the appliance

Severe burns may result. Carefully supervise children in the same room as appliance.

• As with any similar heating appliance, surfaces of the frame, the door and appliance can become very hot.

INSTALLATION INSTRUCTIONS:

The tempered glass

Arch Screen Panel

TOOLS REQUIRED

None

GENERAL INFORMATION

This one-piece decorative screen panel assembly ﬁ ts on the face of the appliance over the glass doorframe. If you encounter any problems, need clariﬁ cation of these instructions or are not qualiﬁ ed to properly install this kit, contact you local distributor or dealer.

Read and understand all instructions and warnings in this document before beginning the installation.

CAUTION

INSTALL ONLY WHEN THE FIREPLACE IS OFF AND COLD!

1. Remove Top Panel - Remove the top louvered or radiant panel/hood assembly by pulling the assembly up and out (see Figure 1). In instances where the radiant panel is used and it is framed in with tile or other approved material, the hood must still be removed by ﬁ rmly pulling it forward until it releases from the receiving brackets. Some models have bustles (as shown in Figure 2) which must be removed. If applicable, remove the top and bottom bustle by lifting them up and out.

Top Panel

Removed

Radiant Panels

Figure 1 - Remove Top Panel

Trim Panels will be either Louvered

Panels or Radiant Panels.

Louvered Panels

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Only Some Models Have Bustles

Bustles

Lift Bustles Up And Off

Figure 2 - Remove Bustles

2. Ensure the glass door assembly on the ﬁ replace is properly aligned as follows:

a. Open or remove lower compartment door (refer to Homeowner’s

Manual provided with appliance).

Note: Units with Modesty Panels - Remove the modesty panel as follows: Lift the modesty panel by the tab on the panel’s right end, pull the right end of the panel away from cabinet and then pull the panel diagonally out of the corner post slots on the left side of the unit. Remove the modesty panel carefully, so that none of the wires become loose or disconnected.

b. Open the latch(es) at the bottom of the glass door assembly as

shown in Figure 3 (refer to Homeowners Manual).

c. Adjust glass door so that it is evenly spaced and aligned to the

ﬁ replace chassis on both sides. See Figure 3.

d. Fasten the latch(es). Ensure that the latch(es) are engaged with

the door’s vee-ﬂ ange and fully closed. See Figure 3.

Top Flange on Glass Door

Glass Door

Install Top of Door ﬁ rst per Instruction #3

Doorframe

Swing the bottom of the doorframe inward, then push into place

Figure 4 - INSTALL DOORFRAME

3. Remove the arched screen doorframe from packaging, then install it as follows:

a. Locate slots on each side of ﬁ replace. b. Position the top of the doorframe above the top of the glass door

assembly (centered and approximately 1” above glass door assembly). See Figure 4.

Note: The bottom of the doorframe should be held slightly away as shown in Figure 4. Swing the bottom of the doorframe inward aligning the sides of the doorframe between the glass door and ﬁ replace chassis and tabs on doorframe aligning into slots on ﬁ replace. Swing the bottom of the doorframe in, then push down to ensure engagement.

4. Ensure that the latch(es) below the door are engaged with the door’s veeﬂ ange and fully closed before operating the ﬁ replace (see Figure 3).

5. (Units with Modesty Panels) Reinstall modesty panel, ensuring all wires are securely connected.

6. If applicable, reinstall the top louver assembly, radiant panels or hood.

7. Reinstall or close the bottom louver or radiant panel.

Some models will have a modesty panel in the control compartment (in front of the valve). The appearance will vary from the example shown below.

Modesty Panel

Bottom Vee-ﬂ ange Glass Door

Glass Door Latch

Firebox Floor

Figure 3 - GLASS DOOR ADJUSTMENT

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Lennox Hearth Products reserves the right to make changes at any time, without notice, in design, materials, speciﬁ cations, prices and the discontinuance of colors, styles and products. Consult your local distributor for ﬁ replace code information.

P/N 750,199M REV. A 04/2006

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Figure 5 - COMPLETED INSTALLATION

1110 West Taft Avenue • Orange, CA 92865