Lennox LSSCA40 User Manual

HEARTH PRODUCTS

KITS AND ACCESSORIES

750,164M REV. A 12/2008

CAST IRON FACADE

LENNOX HEARTH PRODUCTS

INSTALLATION INSTRUCTIONS FOR CAST IRON FACADE KITS Model Numbers LSS-CA35 (H0378) and

LSS-CA40 (H0398) FOR USE WITH SPECTRA LSS SERIES GAS FIREPLACES

GENERAL INFORMATION

These cast iron facade kits are designed to be used in conjunction with the grillwork kits. Together, when installed, these kits complete the front aspect of the Spectra LSS series gas fireplaces. The kits contain one of each of the following cast iron facade pieces: bottom, top, left and right piece. They also contain four 1/2 inch long 1/4-20 facade holding screws, six 1-1/2 inch long 1/4-20 facade holding screws and these instructions.

1/2 inch long Cast Iron Side Piece Holding Screws

3/32 inch

(2.38 mm)

1-1/4 inch (31.8 mm)

INSTALLATION INSTRUCTIONS

Step 1. Install the top and bottom grills to their corresponding top

and bottom cast iron facade pieces as detailed in the installation instructions provided with the grillwork kits.

Step 2. Install five (kit-provided) facade holding screws to each of the two side pieces ensuring compliance with the gaps shown in

Figure 1

Step 3. Hook the two cast iron side pieces onto the fireplace side

channels as shown in gap of the two holding screws. (See

Step 4. Insert set screws into the bottom corners of the arch. Set screws should be flush with the front of the mounting bosses (refer to

Figure 4

Figure 2

. If the fit is too tight or loose, adjust the

Figure 1

KITS

1-1/2 inch long Cast Iron Bottom Piece Holding Screws

Cast Iron Side Piece

Screw Head to Facade Side Piece Gap

Figure 1

1/2 inch long, 1/4-20 Facade Holding Screws

1-1/2 inch long, 1/4-20 Facade Holding Screws (Three Places)

and Fastener Usage.

Side Piece

Cast iron side piece screw head hooked behind top portion of shown fireplace side channel detail (top and bottom same method).

Note: The left cast iron side piece (shown above) is sloped upward at the top, from left to right, to form a mating fit to the arched cast iron top piece. The right cast iron top piece has the opposite slope at the top.

Installing Cast Iron Side Pieces

Figure 2

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Step 5. Slide the top cast iron piece (arched piece) as shown in

Figure 3

on to the two (2) holding screws protruding from the two

cast iron side pieces.

Top Cast Iron (Arch) Piece

Previouly Installed

Bottom Cast Iron Piece

TOP

Slot orientation

indicates facade top.

Cast Iron Side Pieces

See Detail A

Set Screw

Detail A

Figure 4

Bottom Cast Iron Piece Detail Showing Installation Orientation

Installing the Top and Bottom Cast Iron Pieces

Figure 3

Step 6. Adjustment of the set screws on the bottom corners of the

arch can be used to tighten the fit between the sides, the arch and the wall (see

Figure 4

). To adjust the set screw, it will be necessary to remove the top arch. Make adjustments in small increments until the desired fit has been achieved.

Step 7. Hook the bottom cast iron piece (with the top, up, as shown in

Figure 3 )

iron side pieces as shown in

to the 4 holding screws protruding from the two cast

Figure 3

. See

Figure 5

for the final

appearance of the installed cast iron facade.

Installed Fireplace Cast Iron Facade and Grills

Figure 5

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Lennox Hearth Products reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for fireplace code information.

P/N 750,164M REV. A 12/2008

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

LENNOX HEARTH PRODUCTS 1110 West Taft Avenue • Orange, CA 92865