Lennox LPVK-110 User Manual

HEARTH PRODUCTS

5/8” Restrictor

1” Restrictor

Rear Log Bracket

Restrictor Base Plate

Restrictor Body

Down Draft Baffle

KITS AND ACCESSORIES

INSTALLATION INSTRUCTIONS FOR THE ELDV-PVAK (H7407)

FIREPLACE ADAPTER KITS (For LPVK-110)

Fireplace

Model

ELDV

Table 1

KIT CONTENTS

Log Support Bracket - 1 each, Restrictor 5/8” - 1 each, Restrictor 1” - 1 each

TOOLS NEEDED - 5/16” Nut Driver

GENERAL INFORMATION

This kit provides components that are designed to adapt any size ELDV ﬁreplace to be used with the Lennox LPVK-110 Power Vent Kit.

ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND OPERATION MANUAL PROVIDED WITH THE APPLIANCE APPLY TO THESE INSTRUCTIONS.

Kit Catalog

Number

H7407

(ELDV-PVAK)

Kit Contents

P/N 506019-26 REV. N/C 10/2008

Rear Log Support

Remove the 2 screws indicated by arrows

Figure 1 - Log Support Bracket

VENT RUN PARAMETERS

Any Vent Run With A Vertical Height

Greater Than 30 Feet

Any Vent Run With A Vertical Height

Less Than 30 Feet

Note: See Power Vent Kit manual for maximum and minimum vent run parameters.

Table 2

ELDV POWER VENT

ADAPTER KIT

Use 5/8” Restrictor

Provided With This Kit

Use 1” Restrictor

Provided With This Kit

INSTALLATION INSTRUCTIONS

Step 1. Remove the glass door per instructions in the ELDV Care

and Operation Instructions Manual.

Step 2. Using a 5/16” nut driver, remove and discard the rear log sup- port bracket per instructions in Figure 1 and using the same screws,

install the rear log support bracket provided with this kit. Orient as shown in Figure 1.

Step 3. Refer to Figure 2 and remove two screws securing the down- draft bafﬂe. Remove and retain the down-draft bafﬂe.

Step 4. Remove two screws securing the restrictor base plate and remove the restrictor assembly from the ﬁreplace vent outlet.

Step 5. Remove two screws securing the restrictor body to the base plate. Discard the restrictor body.

NOTE: DIAGRAMS AND ILLUSTRATIONS ARE NOT TO SCALE.

Figure 2 - Removing Bafﬂe And Base Plate

Step 6. Refer to Table 2 and determine the appropriate restrictor size

Vent Grips

Mating Cutouts

1” Restrictor

5/8” Restrictor

Mating Tabs

Top Of Fireplace Vent Opening

Top Of Firebox

Restrictor Assembly

6”

2”

to accommodate the required vent run.

Step 7. Refer to Figure 3. If a 5/8” restrictor is required for the installa- tion, nest the 5/8” restrictor with the 1” restrictor by aligning the mating tabs with the mating cutouts, as shown in Figure 3. Secure the 5/8” restrictor to the 1” restrictor by bending the mating tabs over and around the 1” restrictor. If a 1” restrictor is called for, this assembly procedure should not be completed.

Step 8. Position the restrictor within the ﬁreplace vent from above with the vent grips up, this restrictor is self centering and securing (see Figure 4 ). If the restrictor fails to positively engage, remove it from the vent and bend the vent grips outward and then try again.

Step 9. Replace the restrictor base plate and secure with two screws. Replace the down draft bafﬂe and secure with two screws. Refer to Figure 2.

Step 10. Reinstall the glass enclosure panel per instructions in the Care and Operation Instructions manual provided with appliance.

Step 11. Refer to the instructions (manual number 506022-01) provided with the Power Vent Kit (LPVK-110), to complete the task of attaching the Power Vent Kit to the ELDV Fireplace.

Figure 3 - Restrictor Assembly

Figure 4 - Restrictor Assembly Position

Lennox reserves the right to make changes at any time, without notice, in design, materials, speciﬁcations, prices and also to discontinue colors, styles and products. Consult your local distributor for ﬁreplace code information.

P/N 506019-26 REV. N/C 10/2008

NOTE: DIAGRAMS AND ILLUSTRATIONS ARE NOT TO SCALE.

Lennox Hearth Products 1110 West Taft Avenue • Orange, CA 92865