Lennox LBLK-100 User Manual

HEARTH PRODUCTS
KITS AND ACCESSORIES
INSTALLATION INSTRUCTIONS FOR BLOWER KIT
LBLK-100 (CATALOG NO. H4678) FOR USE WITH ELDV SERIES FIREPLACES
GENERAL INFORMATION
This blower kit may be used with ELDV series fireplaces. The LBLK­100 blower kit is used with a field supplied ON/OFF power switch. The blower is installed beneath the firebox. Room air is drawn in through the bottom area of the fireplace, heated as it passes across the firebox, and discharged through the upper open area at the top of the fireplace. The LBLK-100 blower kit contains one blower, one power cord and these instructions.
INSTALLATION INSTRUCTIONS
Step 1. Turn off the fireplace and allow it to cool before proceeding.
Step 2. If the appliance is connected to 120 volt power, disconnect the power.
Step 3. Shut off the gas supply to the fireplace.
750,216M REV. N/C 03/2006
Step 6. Remove the logs from the fireplace ( carefully to prevent breakage.
Step 7. Remove the grate asembly, burner baffle, burner asembly
(
Figure 2
Step 8. Connect the provided power cord to the terminals on the blower.
) and the blower cover panel (
Blower Cover Panel
see Figure 1
Figure 3
BLOWER KIT
LBLK-100
). Handle logs
).
Burner Assembly
Step 4. Remove the bottom panel of the fireplace by pulling it forward.
(
see Figure 1
Step 5. Remove the door assembly by opening the two latches (located under the door assembly) securing the glass door (
Figure 1
).
Logs
see Figure 1
Door Asembly
Bottom Panel
).
Figure 2
Figure 3
Grate Assembly
Blower Cover Panel
Burner Baffle
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
1
Step 9. - Installing The LBLK-100 Blower 9A. First, tilt the left side of the blower into the cutout (
Left Side Of Blower Assembly Tilted Into Access Cutout
see Figure 4
).
Cabinet Bottom
Figure 6
Figure 4
Blower Access Cutout
Step 9B. Next, rest the blower on the cabinet bottom (
see Figure 5
Blower Access Cutout
LBLK-100 Blower Resting On Cabinet Bottom
Figure 5
Step 9C. Now gently slide the blower assembly towards the back of the
fireplace (
see Figure 6
).
).
Cabinet Bottom Blower Assembly Base
Figure 7
Step 9E. Place the blower assembly in its final position at the back of the
cabinet bottom, resting on the blower mounting tabs ( Bend the mounting tabs over the blower base to secure.
Blower Assembly
see Figure 8 )
.
Step 9D. Rotate the blower assembly so the base rests on the cabinet bottom (
2
see Figure 7
).
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Figure 8
Blower Mounting Tab
Blower Base
WIRING DIAGRAM MILLIVOLT GAS VALVES
BLOWER MOUNTING TABS
BLOWER ASSEMBLY
ELECTRICAL OUTLET
APPLIANCE- MOUNTED ON/OFF SWITCH
BK/W(1)
BK/W(1)
THERMOPILE
TP-TH
TP TH
GAS VALVE
120 VAC
BK
GR
W
OPTIONAL BLOWER SWITCH
JUNCTION BOX
INTERMITTENT ELECTRONIC WIRING DIAGRAM
GR
BK
W
R
BK
IGNITOR MODULE
3V
SPARK TO PILOT IGNITOR
BLACK (IGNITOR)
WALL-MOUNTED ON/OFF SWITCH (OPTIONAL) THERMOSTAT (OPTIONAL)
WALL MOUNTED CONFIGURATION FOR FAN SWITCH (OPTIONAL)
BLACK
BK
R
W
GR
FAN
(OPTIONAL)
JUNCTION BOX
Figure 9
120 V
AC
TRANSFORMER 3V
TO WALL SWITCH OR THERMOSTAT
Figure 10
FAN
(OPTIONAL)
Step 10. Install the field-provided ON/OFF switch in a convenient
location on a wall, near the fireplace.
Step 11. Route a 3-wire, 120Vac power line to the ON/OFF switch as shown in
Figure 9
(for Millivolt model) and
Figure 10
(for Electronic
model).
Then route the wires to the unit’s junction box. Remove the receptacle box by squeezing the sides of the J-Box and slide the two tabs through the cutout.
BLACK (SENSOR)
BLACK
BATTERY BACK-UP
RED
BROWN
BROWN
ORANGE (THTP)
BLACK (TP)
GREEN (TH)
TP
HI
LO
TH
OUT
VENT
PILOT
IN
TH
TP
IMPORTANT: Ground lead must be connected to the green screw located on the junction box. Failure to do so will prevent the appliance from operating. The appliance must be electrically
grounded in accordance with local codes or, in the absence of local codes, the National Electrical Code, ANSI/NFPA 70-(latest edition). (In Canada, the current CSA C22-1 Canadian Electrical Code.)
IN
Step 12. Connect the supply wires to the receptacle as shown in
Figure 9
(for Millivolt) and
Figure 10
(for Electronic). Reinstall the
receptacle box.
Step 13. Plug the blower cord into the receptacle (
see Figure 11
Step 14. Reinstall items from Steps 7, 6 and 5.
Step 15. Restore the electrical power to the unit.
Step 16. Start the fireplace by following the procedures indicated in
the lighting instructions section of the Homeowners Care And Opera­tions instructions manual, supplied with the fireplace.
Step 17. Check the start-up and shutdown, and the running operation of the blower.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
).
Figure 11
3
The manufacturer reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for fireplace code information.
Printed in U.S.A. © 2006 by Lennox Hearth Products
P/N 750,216M REV. N/C 03/2006
4
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
1110 West Taft Avenue - Orange, CA 92865
Loading...