OPERATION MANUAL
E2008 Lennox Industries Inc.
Dallas, Texas, USA
RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE
ComfortSenset 3000 Series
Model No. L3011C
Non-Programmable Thermostat
CONTROLS
506079−01
02/08
Supersedes 504,865M
Table of Contents
L3011C Thermostat 1. . . . . . . . . . . . . . . . . . . . . . . . . . . .
General 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Initial Thermostat Power-up 1. . . . . . . . . . . . . . . . . . . . .
Heating Control 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cooling Control 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting Temperature Setpoint 3. . . . . . . . . . . . . . . . .
Fan Control 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Filter Reminder 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Indicator 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Thermostat RESET 5. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Default Thermostat Settings 5. . . . . . . . . . . . . . . . . . . .
Technical Specifications 5. . . . . . . . . . . . . . . . . . . . . . . .
Thermostat Output Table 6. . . . . . . . . . . . . . . . . . . . . . .
Litho U.S.A.
L3011C Thermostat
The Lennox ComfortSenset 3000 Series model L3011C
non-programmable electronic thermostat is easy-to-use,
has a large, easy-to-read display, and provides excellent
temperature control. The thermostat also includes a programmable filter change reminder, and a system check indicator which will notify the user of the need for equipment
service.
Thermostat model L3011C t is suitable for non-heat pump,
single−stage heat/single cool applications that are
matched with a gas or electric furnace.
General
These instructions are intended as a general guide and do
not supersede local codes in any way. Consult authorities
having jurisdiction before installation.
Check equipment for shipping damage. If you find any
damage, immediately contact the last carrier.
Introduction
This document describes the operation of Lennox model
L3011C thermostat. Refer to the installation manual for
instructions regarding installation and wiring of the thermostat.
Initial Thermostat Power-up
When power is initially applied to the thermostat, the display will appear as shown in figure 1.
FILTER
ROOM
SETPOINT
Figure 1. Display − Initial Power−Up
All display segments are momentarily activated. This occurs as a normal part of thermostat initialization. Within a
few seconds, the display will appear as shown in figure 2
(figure shows temperature in Fahrenheit units).
88
88
SERVICE
FAN
ON
AUTO
SYSTEM
COOL
OFF
EMG.
HEAT
02/08 506079−01
*2P0208* *P506079-01*
ROOM
70
FAN
AUTO
If the thermostat is in heat mode, heat mode is disabled
when the HEAT button is pressed. This is indicated by OFF
in the SYSTEM box as shown in figure 5.
SYSTEM
HEAT
Figure 2. Display − Home Screen
Figure 2 illustrates the HOME screen. Note that an indoor
room temperature of 70°F is initially displayed. After about
1 minute of warm−up time, the actual room temperature will
be displayed. HEAT mode is the system default (as indicated in the SYSTEM box at lower right).
A pale blue display backlight will turn on each time a key is
pressed. The backlight will turn off 8 seconds after the last
key is pressed.
Heating Control
The HEAT button is located behind the small door on the
right−hand side of the thermostat. See figure 3.
ROOM
SETPOINT
Figure 5. Heat Mode Disabled
Heating Demand
The thermostat must be in heat mode in order to properly
control the heating equipment. When in heat mode, if the
actual temperature is lower than the temperature setpoint, a
heating demand is detected by the thermostat. The thermostat will then activate the heating equipment to satisfy the demand. Heating operation is indicated by a flame icon in the
SYSTEM box as shown in figure 6.
ROOM
69
64
72
FAN
AUTO
SYSTEM
OFF
FAN
AUTO
Figure 3. Additional Thermostat Buttons
Enabling and Disabling Heat Mode
Use the HEAT button to enable or disable heat mode as
desired. If the thermostat is in off mode, heat mode is enabled when the HEAT button is pressed. This is indicated
by HEAT in the SYSTEM box as shown in figure 4.
ROOM
SETPOINT
Figure 4. Heat Mode Enabled
69
64
FAN
AUTO
SYSTEM
HEAT
88
Figure 6. Heating Demand
When the actual temperature rises above the temperature
setpoint, the flame icon will disappear. This indicates that
the heating demand has been satisfied and that the heating equipment has been turned off.
NOTE − The heating equipment is activated for at least 3
minutes if no buttons are pressed during the demand interval.
Cooling Control
The COOL button is located behind the small door on the
right-hand side of the thermostat. See figure 3.
Enabling and Disabling Cool Mode
Use the COOL button to enable or disable cool mode as
necessary. If the thermostat is in off mode, cool mode is
enabled when the COOL button is pressed. This is indicated by COOL in the SYSTEM box.
If the thermostat is in cool mode, cool mode is disabled
when the COOL button is pressed. This is indicated by
OFF in the SYSTEM box.
SYSTEM
HEAT
506079−01 02/08
Page 2
Cooling Demand
The thermostat must be in cool mode in order to properly
control the cooling equipment. When in cool mode, if the
room temperature is higher than the temperature setpoint,
a cooling demand is detected by the thermostat.
The thermostat will then activate the cooling equipment to
satisfy the demand. Cooling operation is indicated by a
snowflake icon in the SYSTEM box as shown in figure 7.
When the actual temperature drops below the temperature
setpoint, the snowflake icon will disappear. This indicates
that the cooling demand has been satisfied and that the
cooling equipment has been turned off.
ROOM
Figure 7. Cooling Demand
NOTE − The cooling equipment is activated for at least 4
minutes if no buttons are pressed during the demand interval. Cooling equipment operation is locked out for 5 minutes after a demand has been satisfied. If another cooling
demand occurs during this 5−minute interval, the snowflake icon will flash; however, the cooling equipment will
not run until the 5−minute delay has elapsed.
Adjusting Temperature Setpoint
The temperature setpoint represents the desired temperature of the space around the thermostat. The default temperature setpoint is 70°F. To adjust the setpoint, press the
UP or DOWN arrow keys to the right of the display screen.
The existing setpoint will be displayed just below the actual
room temperature as shown in figure 8.
79
FAN
AUTO
SYSTEM
COOL
Use the UP or DOWN arrow keys to adjust the setpoint up
or down. The setpoint will increase by 1°F each time the
UP key is pressed. The setpoint will decrease by 1°F each
time the DOWN key is pressed.
After the desired setpoint is reached, the HOME screen
will reappear after about 8 seconds.
Fan Control
The FAN button is located behind the small door on the
right-hand side of the thermostat. See figure 3. The FAN
button can be used to select either continuous fan mode or
auto fan mode.
If continuous fan mode is enabled, the fan will run continuously regardless of whether the heating or cooling equipment is running. Also, ON will be displayed in the FAN box
as shown in figure 9.
ROOM
Figure 9. Fan ON with Icon
If auto fan mode is selected, the fan will only run when the
heating or cooling equipment is running. In this case,
AUTO will be displayed in the FAN box as shown in figure 10.
ROOM
73
73
FAN
ON
SYSTEM
HEAT
FAN
AUTO
ROOM
SETPOINT
Figure 8. Setpoint Display and Adjustment
69
64
FAN
AUTO
SYSTEM
HEAT
SYSTEM
HEAT
Figure 10. Fan AUTO with Icon
To change from continuous to auto fan mode and vice versa, press the FAN button. Also note the presence of a fan
icon in the FAN box. This icon indicates that the fan is running.
Page 3
L3011C THERMOSTAT
Filter Reminder
The L3011C thermostat includes a filter reminder feature.
The filter reminder can be set for 1, 3, 6, or 12−month intervals. The SETTINGS button, located behind the door on
the right−hand side of the thermostat is used to set the filter
reminder interval. See figure 3. Press the SETTINGS button from the HOME screen to display the Filter Reminder
Settings screen as shown in figure 11.
FILTER
0
Figure 11. Filter Reminder Settings
The default setting for the filter reminder is 0, which disables the function. Use the UP arrow while in the Filter Reminder Settings screen to select the desired interval between reminders. It may be necessary to press the UP
arrow several times to access the desired setting. The
HOME screen will reappear about 10 seconds after the arrow key has been pressed for the final time.
After the programmed interval has elapsed, the FILTER reminder will be displayed as shown in figure 12. After the filter has been changed, reset the filter reminder by pressing
the SETTINGS button for 4 seconds. The screen will blink
for a few moments to indicate that the timer has been reset.
FILTER
ROOM
Figure 12. Display of Filter Reminder
Service Indicator
When abnormal equipment operation is detected, the
SERVICE indicator will flash on the upper-right corner of
the screen. This indicates that the equipment requires service from a qualified service technician. The SERVICE indicator is shown in figure 13.
ROOM
Figure 13. Service Indicator Flashing
72
73
FAN
AUTO
SYSTEM
HEAT
SERVICE
FAN
AUTO
SYSTEM
HEAT
506079−01 02/08
Page 4
Thermostat RESET
Under some abnormal conditions, it may be desirable to
reset" the thermostat to its default condition. This can be
useful on rare occasions when the the thermostat is behaving abnormally (e.g. after an electrical storm or power outage). The RESET button can be used to recover from this
situation.
The RESET button is an unlabeled, recessed button located behind the door on the right−hand side of the thermostat, just below the SETTINGS button. The RESET button
is visible in figure 3. Use a paper clip or small pencil to
press the RESET button. After the RESET button is
pressed, the thermostat settings will return to the defaults
listed in the Default Settings section.
Default Thermostat Settings
Default thermostat settings are in table 1.
Table 1. Default Thermostat Settings
Mode Heat
Setpoint 70°F (or 21°C)
Fan Auto
Filter Reminder OFF (reminder setting = 0)
Equipment Protection
Timers
Reset back to zero
Technical Specifications
Thermostat Type
Electronic nonprogrammable thermostat for 1H/1C, gas or
electric heat, non−heat pump, non−power robbing applications.
Power Supply Range
18VAC − 30VAC (24VAC nominal), 60Hz
Temperature Display
Display Scale: Fahrenheit or Celsius user selectable (via
DIP switches)
Display range: 35°F (2°C) to 99°F (37°C)
Display resolution: 1°F (1°C)
Display Accuracy: +/−1°F
Temperature Measurement Range
Measurement Scale: Fahrenheit
Measurement Range: 35°F to 99°F
Measurement Resolution: 0.5°F
Measurement Accuracy: +/−1°F
Field Offset: via DIP switches to +/−3°F
Sampling Method: temperature measurements sampled
every 15 seconds. Displayed temperature is the average
of the last four measurements.
Temperature Setpoint Range
Setting range: 50°F (10°C) to 90°F (32°C)
Setting resolution: 1°F (1°C)
Fan Control
AUTO or ON modes, gas or electric heat compatible via
DIP switches (also see Thermostat Output section).
I/O Relays
All thermostat relays are latching type to minimize power
consumption.
1.. HEAT/COOL relay output
2.. FAN relay output
3.. SERVICE relay input
Equipment Protection Timers
Minimum Compressor OFF time: 5 minutes
Minimum Compressor ON time: 4 minutes
Minimum Furnace ON time: 3 minutes
Minimum furnace cycle time (elapsed time between any
furnace activation and the next furnace activation): 6 minutes.
Minimum elapsed time between any compressor activation and the next compressor activation: 6 minutes.
NOTE − All protection timers (except the compressor OFF
timer) can be over−ridden if a heating or cooling demand is
initiated or terminated using the UP, DOWN, HEAT, or
COOL buttons.
Equipment Protection Override
Both the minimum compressor OFF timer and the minimum equipment cycle timer can be over−ridden by pressing and holding either the HEAT or COOL button down for 4
seconds.
Over−Temperature Protection
Thermal mechanical switch opens W1 at 93°F+/−6°F.
Filter Reminder
Settings of 0 (Off), 1, 3, 6 or 12 months are available. When
programmed time has elapsed, a FILTER indicator is displayed.
Service Reminder
The SERVICE indicator is displayed only under the following conditions:
S if the thermostat Y1 terminal has been activated with
24VAC for at least 5 minutes, AND the L terminal is
shorted to the R terminal;
OR
S if the thermostat Y1 terminal has been activated with
24VAC for at least 5 minutes, AND the L terminal is
shorted to the C terminal.
Page 5
L3011C THERMOSTAT
Power Loss/Recovery
Thermostat memory is retained for a minimum of 24 hours
during a power loss (includes retention of programmed
temperature setpoint, heat/cool and fan mode settings, filter reminder status, and equipment protection timers). After 24 hours of power loss, programmed settings will be
lost and replaced with default settings.
IMPORTANT
Power must be applied for at least six consecutive
hours prior to a power loss in order for memory to
be retained for the specified time.
LCD Backlight
Activated for 8 seconds when any key is pressed.
NOTE − During an electrical storm or similar disturbance,
the backlight may activate for a few seconds. This is normal and will no longer occur after the electrical disturbance
has passed.
Thermostat Operating Conditions
35°F to 105°F, 5% to 90% RH
Thermostat Storage Conditions
−40°F to 185°F, 5% to 95% RH
Thermostat Output Table
Table 2 depicts the L3011C thermostat output states for
various input conditions.
Table 2. L3011C Thermostat Outputs
Condition
Gas Heat, Auto Fan
heat demand X
cool demand X X
no demand
Gas Heat, Continuous Fan
heat demand X X
cool demand X X
no demand X
Electric Heat, Auto Fan
heat demand X X
cool demand X X
no demand
Electric Heat, Continuous Fan
heat demand X X
cool demand X X
no demand X
NOTE − X = output is activated with 24VAC.
W1 Y1 G
506079−01 02/08
Page 6
Loading...