Lennox ELDV-35, ELDV-40, ELDV-45 User Manual
HEARTH PRODUCTS
KITS AND ACCESSORIES
INSTALLATION INSTRUCTIONS FOR EYEBROW LINTEL KITS
FOR USE WITH ELDV-35, ELDV-40 & ELDV-45 DIRECT VENT GAS FIREPLACES
KIT CONTENTS:
1 ea. Eyebrow
1 ea. Lintel
3 ea. #10 Screws
1 ea. Instruction Sheet
CAT. NO. MODEL NO. WHERE USED
H4387 ELDV35 ELDV-35
H4388 ELDV40 ELDV-40
H4389 ELDV45 ELDV-45
Table 1
TOOLS NEEDED:
5/16” Nut Driver or Socket
#26 (.147") Drill Bit
Drill Motor
Eyebrow Lintel Kits
750,235M
Rev. NC, 08/2006
EYEBROW LINTEL KITS
INSTALLATION INSTRUCTIONS
Step 1. Remove glass door assembly per the following instructions.
WARNING
Handle this glass with extreme care! The glass panel is
susceptible to damage — do not scratch while handling
or while re-installing the glass door frame.
WARNING
Do not operate appliance with the glass front removed,
cracked or broken. Replacement of the glass should be
done by a licensed or qualifi ed service technician.
HEARTH PRODUCTS
KITS AND ACCESSORIES
750,235M
EYEBROW LINTEL KITS
Rev. NC, 07/2006
INSTALLATION INSTRUCTIONS FOR EYEBROW LINTEL KITS
FOR USE WITH ELDV-35, ELDV-40 & ELDV-45 DIRECT VENT GAS FIREPLACES
KIT CONTENTS:
TOOLS NEEDED:
INSTALLATION INSTRUCTIONS
1 ea. Eyebrow
5/16” Nut Driver or Socket
Step 1. Remove glass door assembly per the following instrucitons.
1 ea. Lintel
#26 (.147") Drill Bit
3 ea. #10 Screws
Drill Motor
1 ea. Instruction Sheet
WARNING
Eyebrow Lintel Kits
Handle this glass with extreme care! The glass panel is
CAT. NO. MODEL NO. WHERE USED
susceptible to damage — do not scratch while handling
or while re-installing the glass door frame.
ELDV-35
ELDV-40
ELDV-45
WARNING
Table 1
Do not operate appliance with the glass front removed,
cracked or broken. Replacement of the glass should be
done by a licensed or qualifi ed service technician.
Lintel
Glass Door Removal Procedure:
Refer to Figure 2 and remove the front glass enclosure panel as
follows:
Eyebrow
1. Remove the bottom compartment door by lifting and pulling it towards
the front of the fi replace.
Instruction Sheet
2. Locate the two (2) latches at the top of the control compartment
Screws
and disengage them from the fl oor frame bottom Vee-fl ange, pulling
Figure 1 - Kit Contents
down on their handles to open them.
3.Swing the bottom of the door out and raise it slightly to lift the top
fl ange of the door frame away from the appliance.
IMPORTANT
INSTALL ONLY WHEN APPLIANCE IS OFF AND COLD!
GENERAL INFORMATION
These eyebrow lintel kits are designed to provide an aesthetically pleasing
appearance and conceal the gap above the fi replace.
ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND
HOMEOWNER'S MANUALS PROVIDED WITH THE APPLIANCE APPLY
TO THESE INSTRUCTIONS.
If you encounter any problems, need clarifi cation of these instructions
or are not qualifi ed to properly install this kit, contact you local distributor or dealer.
Door
Assembly
Bottom Panel
Figure 2 - Glass Door Removal and Reinstallion.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Instruction Sheet
Eyebrow
Screws
Lintel
Figure 1 - Kit Contents
IMPORTANT
INSTALL ONLY WHEN APPLIANCE IS OFF AND COLD!
GENERAL INFORMATION
These eyebrow lintel kits are designed to provide an aesthetically pleasing
appearance and reduces the gap above the fi replace.
ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND
HOMEOWNER'S MANUALS PROVIDED WITH THE APPLIANCE APPLY
TO THESE INSTRUCTIONS.
If you encounter any problems, need clarifi cation of these instructions
or are not qualifi ed to properly install this kit, contact you local distributor or dealer.
Glass Door Removal Procedure:
Refer to Figure 2 and remove the front glass enclosure panel as
follows:
1. Remove the bottom compartment door by lifting and pulling it towards
the front of the fi replace.
2. Locate the two (2) latches at the top of the control compartment
and disengage them from the fl oor frame bottom Vee-fl ange, pulling
down on their handles to open them.
3. Swing the bottom of the door out and raise it slightly to lift the top
fl ange of the door frame away from the appliance.
Door
Assembly
Bottom Panel
Figure 2 - Glass Door Removal and Reinstallation.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
1
Step 2. Using a 5/16" socket or nutdriver, remove the existing lintel as
shown in Figure 3. Retain the screws for Step 3.
Eyebrow Mounting Holes
Lintel
Figure 3 - Removing Lintel
Step 3.Install the new lintel provided using the screws that were removed
in step 2 (reversing instructions in step 2 and see Figure 3).
Step 4. Install the eyebrow as follows:
Note: Three holes must be drilled in the fi replace to install the eyebrow.
When the eyebrow is properly aligned to the appliance, drill into the holes
on the eyebrow and into fi replace.
1. Align the eyebrow provided as shown in Figure 4. Ensure that
the eyebrow is pushed in fl ush to the fi replace front.
2. Drill into fi replace through the center hole on eyebrow.
3. Install a screw (provided) into the center hole on eyebrow into
hole that you drilled. Repeat this process for the other 2 holes
on eyebrow using the other 2 screws provided. See Figure 5.
Drill through the
center mounting
hole fi rst, then install screw. Repeat
this process for the
other 2 holes.
Figure 5 - Installing Eyebrow
Step 5. Reinstall glass door per instructions in Homeowner's Manual and
per Step 1 and Figure 1.
Eyebrow
Lintel
Ensure Eyebrow is pushed in
fl ush to fi replace front.
Eyebrow
Figure 4 - Installing Eyebrow
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
LHP reserves the right to make changes at any time, without notice, in design, materials, specifi cations, prices and the discontinuance of colors, styles and products. Consult your local
distributor for fi replace code information.
Figure 6 - Completed Installation
Printed in U.S.A. © 2006 by LHP
P/N 750,235M REV. NC 08/2006
LHP
1110 West Taft Avenue
Orange, CA 92865
Loading...