Lennox EDVCR, EBVPF, EBVCL, EDVPF, EBVST User Manual

...
LOG PLACEMENT GUIDE
Glowing Embers
LOG PLACEMENT GUIDE FOR LENNOX DIRECT VENT AND B-VENT SERIES
MULIT-OPEN GAS FIREPLACE HEATERS
GENERAL INFORMATION
This log placement guide has been prepared to present detailed log placement illustrations and provide instruction to assist in the place­ment of logs at the initial (new appliance) setup and after the annual cleaning and inspection cycles. The information provided here is to be used in conjunction with the Homeowner's Care and Operation In­structions provided together with this document in the appliance lit­erature packet. Please read the Homeowner's Care and Operation In­structions completely before completing the procedures detailed in this placement guide.
INITIAL INSTALLATION CONSIDERATIONS
If the logs are being installed for the first time, the following para­graphs apply:
DO NOT attempt to install the logs until the appliance installation has been completed, the gas line connected and tested for leaks and the initial burner operation has been checked out.
750,161M REV. B 10/2004
Figure 1
EDVPF, EDVST, EDVCL, EDVCR, EBVPF,
EBVST, EBVCL AND EBVCR SERIES
Step 1. Remove the appliance front door.
Step 2. Remove the foamed log set from the interior of the firebox. Remove the logs from their packaging. Handle logs carefully to pre­vent breakage.
CERAMIC FLOOR PANELS, LOGS AND GLOWING EMBER PLACEMENT
Step 1. Install the Ceramic Floor Panels as shown in
Direct Vent fireplaces only).
Note: This appliance is provided with enough Glowing Embers for sev­eral applications, do not feel compelled to use all that is in a new bag. For best glowing effect, replace the ember material annually. Replace­ment Glowing Embers are available (Catalog Number 88L53).
Step 2. Position the individual logs as shown in
on pages 3 and 4
that have notches to fit over the grate tines should be positioned with these notches directly against the grate. Proper log placement is criti­cal to encourage outstanding flame appearance and prevent sooting. When positioned properly as shown, logs will be positioned between flame peaks and will not impinge any flames.
. Logs should be placed in the order shown. All logs
Figure 3
Figures 4A and 4B
(for
Figure 2
Note: Do Not place Glowing Embers (Rockwool) over burner slots.
Step 3. Separate the Glowing Ember (Rockwool) into pieces about
the size of a quarter Distribute these pieces over the front surface of the burner, as shown in
Figure 2
tioned, the Glowing Embers will cover approximately 65% of the front burner and with no appreciable gaps or openings. Ensure that the main burner ports remain uncovered by the ember material.
. Do not use more than is necessary. When properly posi-
Figure 1
. Keep the pieces fluffed up, not matted.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
1
CERAMIC FLOOR PANEL PLACEMENT (Direct Vent Fireplaces Only)
Catalog Number for the Ceramic Floor Panel set: 55M4901 (For EDVPF), 55M5101 (For EDVCL),
55M5501 (For EDVST) And 55M7601 (For EDVCR).
1 1/4" Dia. Through Holes (4 Places)
Ceramic Floor Panel
Log Support
EDVST Shown
Burner
Place The Four Legs Of The Grate Assembly In The Four Holes Of The Ceramic Floor Panel
Small Door Opening
Chamfer Corner Pointing Toward
Burner
EDVCL Shown*
Small Door Opening
*NOTE: EDVCR & EDVPF Are Installed In Similar Fashion With Chamfer End Pointing Toward Small Door Opening
1 1/4" Dia. Through Holes (4 Places)
Ceramic Floor Panel
Figure 3
2
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Loading...
+ 2 hidden pages