Lennox EBSTPM-2, EBSTNM-2 User Manual
HOMEOWNER'S CARE AND
OPERATION INSTRUCTIONS
B-VENT MULTI-OPEN
EBST (See-through) EBPF (Peninsula)
EBCL (Corner-Left)
RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE
OTL Report No. 116-F-07-5
WARNING: IF THE INFORMATION IN THIS MANUAL
IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
FOR YOUR SAFETY: Do not store or use gasoline
or other flammable vapors or liquids in the vicinity of this or any other appliance.
EBCR (Corner-Right)
ELITE
B-VENTED GAS APPLIANCES
P/N 875,012M REV. D 05/2004
SERIES
MODELS
sledoMtlovilliMsledoMcinortcelE
2-MNTSBE2-MNRCBE2-ENTSBE2-ENRCBE
2-MPTSBE2-MPRCBE2-EPTSBE2-EPRCBE
2-MNFPBE2-MNLCBE2-ENFPBE2-ENLCBE
2-MPFPBE2-MPLCBE2-EPFPBE2-EPLCBE
MNYABBEPNYABBEENYABBE
AVERTISSEMENT: ASSUREZ-VOUS DE BIEN SUIVRE
LES INSTRUCTIONS DONNÉ DANS CETTE NOTICE POUR
RÉDUIRE AU MINIMUM LE RISQUE D'INCENDIE OU
POUR ÉVITER TOUT DOMMAGE MATÉRIEL, TOUTE
BLESSURE OU LA MORT.
POUR VOTRE SÉCURITÉ: Ne pas entreposer ni utiliser
d'essence ni d'autre vapeurs ou liquides inflammables
dans le voisinage de cet appareil ou de tout autre
appareil.
POUR VOTRE SÉCURITÉ: Que faire si vous sentez une
odeur de gaz:
®
FOR YOUR SAFETY: What to do if you smell gas:
• DO NOT light any appliance.
• DO NOT touch any electrical switches.
• DO NOT use any phone in your building.
• Immediately call your gas supplier from a
neighbor’s phone.
Follow your gas suppliers instructions.
• If your gas supplier cannot be reached, call the
fire department.
Installation and service must be performed by a
qualified installer, service agency or the gas
supplier.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
• Ne pas tenter d'allumer d'appareil.
• Ne touchez à aucun interrupteur. Ne pas vous servir
des téléphones se trouvant dans le batiment où
vous vous trouvez.
• Evacuez la piéce, le bâtiment ou la zone.
• Appelez immédiatement votre fournisseur de gaz
depuis un voisin. Suivez les instructions du
fournisseur.
• Si vous ne pouvez rejoindre le fournisseur de gaz,
appelez le service dos incendies.
L'installation et service doit être exécuté par un
qualifié installeur, agence de service ou le fournisseur
de gaz.
1
CONGRATULATIONS!
GENERAL INFORMATION
In selecting this LENNOX B-Vented Gas Appliance you have chosen the finest and
most dependable fireplace to be found anywhere. Its a beautiful, prestigious
alternative to a wood burning fireplace. Welcome to a Family of tens of thousands
of satisfied LENNOX Fireplace Owners.
Please carefully read and follow all of the instructions found in this manual. Please
pay special attention to the safety instructions provided in this manual. The
Homeowner's Care and Operation Instructions included here will assure that you
have many years of dependable and enjoyable service from your LENNOX product.
TABLE OF CONTENTS
Introduction...................................... page 2
General Information.......................... page 2
Operation/Care of Your Appliance.....page 3
Gas Controls/Control Compartment,
Access ............................................ page 4
Variable Flame Adjustment ............... page 5
Outside Combustion Air Control ....... page 5
Venting Action and Safety Limit........page 5
Maintenance ..................................... page 6
Front Glass Enclosure Panel,
Removal and Installation ................ page 6
Maintenance Schedule...................... page 7
Burner Adjustments.......................... page 8
Log Placement.................................. page 9
Vermiculite and Black/Gray Ceramic
Fiber Chunks Placement ................ page 9
Millivolt Appliance Checkout............. page 9
Electronic Appliance Checkout..........page 10
Wiring Diagrams...............................page 10
Warranty........................................... page 10
Replacement Parts ............................ page 10
Product Reference Information ........page 10
Accessory Components.................... page 11
Lighting Instructions – Millivolt........ page 14
Lighting Instructions – Electronic..... page 16
Troubleshooting Guide – Millivolt ......page 18
Troubleshooting Guide – Electronic ... page 19
Replacement Parts List...................... page 21
INTRODUCTION
The millivolt appliances are designed to operate
on either natural or propane gas. A millivolt gas
control valve with piezo ignition system provides safe, efficient operation. If any optional
accessories which require electrical power are
being installed, the electrical power must be
provided at the time of appliance installation.
The electronic appliances are designed to operate on either natural or propane gas. An
electronic intermittent pilot system provides
safe, efficient operation. External electrical
power is required to operate these units.
These appliances comply with National Safety
Standards and are tested and listed by OmniTest Laboratories (Report No. 116-F-07-5) to
ANSI Z21.50 - 2000 (in Canada, CSA 2.22 -
2000), and CAN/CGA-2.17-M91 in both USA
and Canada, as vented gas fireplaces.
Installation must conform to local codes. In
the absence of local codes, installation must
comply with the current National Fuel Gas
Code, ANSI Z223.1 (NFPA 54). (In Canada, the
current CAN/CGA B149 installation code.) Electrical wiring must comply with local codes. In
the absence of local codes, installation must
be in accordance with the National Electrical
Code, NFPA 70 - (latest edition). (In Canada,
the current CSA C22.1 Canadian Electric Code.)
DO NOT ATTEMPT TO ALTER OR MODIFY
THE CONSTRUCTION OF THE APPLIANCE OR
ITS COMPONENTS. ANY MODIFICATION OR
ALTERATION MAY VOID THE WARRANTY,
CERTIFICATION AND LISTINGS OF THIS UNIT.
WARNING: IMPROPER INSTALLATION,
ADJUSTMENT, ALTERATION, SERVICE
OR MAINTENANCE CAN CAUSE INJURY
OR PROPERTY DAMAGE. REFER TO THIS
MANUAL. FOR ASSISTANCE OR ADDITIONAL INFORMATION CONSULT A
QUALIFIED INSTALLER, SERVICE
AGENCY OR THE GAS SUPPLIER.
Note: Installation and repair should be per-
formed by a qualified service person. The appliance should be inspected annually by a qualified professional service technician. More frequent inspections and cleanings may be required due to excessive lint from carpeting,
bedding material, etc. It is imperative that the
control compartment, burners and circulating
air passage ways of the appliance be kept clean.
S'assurer que le brùleur et le compartiment des
commandes sont propres. Voir les instructions d'installation et d'utilisation qui
accompagnent l'appareil.
Provide adequate clearances around air openings and adequate accessibility clearance for
service and proper operation. Never obstruct
the front openings of the appliance.
Due to high temperatures the appliance should
be located out of traffic and away from furniture and draperies. Locate furniture and window coverings accordingly.
WARNING: THESE FIREPLACES ARE
VENTED DECORATIVE GAS APPLIANCES.
DO NOT BURN WOOD OR OTHER MATERIAL IN THESE APPLIANCES.
These appliances are designed to operate on
natural or propane gas only.
Input of millivolt models is shown in the following table:
sledoMtlovilliM
enaporPdnalarutaN
sledoMsaG
,2-MNFPBE,2-MNTSBE
,2-MPFPBE,2-MPTSBE
PNYABBE,MNYABBE
,2-MNRCBE,2-MNLCBE
2-MPRCBE,2-MPLCBE
Input of electronic models is shown in the
following table:
sledoMcinortcelE
enaporPdnalarutaN
sledoMsaG
,2-ENFPBE,2-ENTSBE
,2-EPFPBE,2-EPTSBE
ENYABBE
,2-ENRCBE,2-ENLCBE
2-EPRCBE,2-EPLCBE
)H/UTB(etartupnI
detaludom-yllaunaM
005,73OT000,03
000,43OT000,62
)H/UTB(etartupnI
etaRdexiF
005,73
000,43
2
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
The following table shows the units' gas orifice size for the elevations indicated:
.taN.porP
*ezisecifirO
noitavelE
)sretem(teeF
0054-0
)2731-0(
ledoM
.oN
2-TSBE
2-FPBE
44#55#
YABBE
2-RCBE
74#"50.0
2-LCBE
* Each model has two burners. Each burner
contains one of these orifices.
Maximum manifold pressure is 3.5 in. w.c.
(0.87 kPa) for natural gas and 10 in. w.c. (2.49
kPa) for LP/Propane gas.
Do not use these appliances if any part has
been under water. Immediately call a qualified,
professional service technician to inspect the
appliance and to replace any parts of the
control system and any gas control which
have been under water.
Ne pas se servir de cet appareil s'il a été plongé
dans l'eau, complètement ou en partie. Appeler
un technicien qualifié pour inspecter l'appareil
et remplacer toute partie du système de
contrôle et toute commande qui ont été plongés
dans l'leau.
Test gage connections are provided on the
front of the millivolt gas control valve (identified OUT for the manifold side and IN for inlet
pressure. A ¹⁄₈" NPT test gage connection is
provided on the electronic gas control valve
adjacent to the outlet to the main burner.
Minimum inlet gas pressure to these appliances is 5.0 inches water column (1.24 kPa)
for natural gas and 11 inches water column
(2.74 kPa) for propane for the purpose of input
adjustment.
Maximum inlet gas supply pressure to these
appliances is 10.5 inches water column (2.61
kPa) for natural gas and 13.0 inches water
column (3.23 kPa) for propane.
The appliance must be isolated from the gas
supply piping system (by closing its individual
manual shut-off valve) during any pressure testing of the gas supply piping system at test
pressures equal to or less than ¹⁄₂ psig (3.5 kPa).
The appliance and its individual shut-off valve must
be disconnected from the gas supply piping system
during any pressure testing of that system at pressures in excess of ¹⁄₂ psig (3.5 kPa).
These appliances must not be connected to a
chimney or flue serving a separate solid fuel
burning appliance.
Any safety guard or screen removed for servicing the appliance must be replaced prior to
operating the appliance.
WARNING: B-VENT APPLIANCES ARE NOT
DESIGNED TO OPERATE IN NEGATIVELY
PRESSURED ENVIRONMENTS (PRESSURE
WITHIN THE HOME IS LESS THAN PRESSURES OUTSIDE). SIGNIFICANT NEGATIVELY PRESSURED ENVIRONMENTS
CAUSED BY WEATHER, HOME DESIGN,
OR OTHER DEVICES MAY IMPACT THE
OPERATION OF THESE APPLIANCES.
NEGATIVE PRESSURES MAY RESULT IN
POOR FLAME APPEARANCE, SOOTING,
DAMAGE TO PROPERTY AND/OR SEVERE
PERSONAL INJURY. DO NOT OPERATE
THESE APPLIANCES IN NEGATIVELY PRESSURED ENVIRONMENTS. PROVIDING ADEQUATE VENTILATION TO THE APPIANCE
FOR COMBUSTION AIR WILL ELIMINATE A
NEGATIVE PRESSURE ENVIRONMENT.
WARNING: FAILURE TO COMPLY WITH
THE INSTALLATION AND OPERATING INSTRUCTIONS PROVIDED IN THIS DOCUMENT WILL RESULT IN AN IMPROPERLY INSTALLED AND OPERATING APPLIANCE, VOIDING ITS WARRANTY. ANY
CHANGE TO THIS APPLIANCE AND/OR
ITS OPERATING CONTROLS IS DANGEROUS. IMPROPER INSTALLATION OR USE
OF THIS APPLIANCE CAN CAUSE SERIOUS INJURY OR DEATH FROM FIRE,
BURNS, EXPLOSION OR CARBON MONOXIDE POISONING.
Carbon Monoxide Poisoning: Early signs of
carbon monoxide poisoning are similar to
the flu with headaches, dizziness and/or
nausea. If you have these signs, obtain
fresh air immediately. Turn off the gas
supply to the appliance and have it serviced by a qualified professional, as it may
not be operating correctly.
WARNING: CHILDREN AND ADULTS
SHOULD BE ALERTED TO THE HAZARDS
OF HIGH SURFACE TEMPERATURES. USE
CAUTION AROUND THE APPLIANCE TO
AVOID BURNS OR CLOTHING IGNITION.
YOUNG CHILDREN SHOULD BE CAREFULLY SUPERVISED WHEN THEY ARE IN
THE SAME ROOM AS THE APPLIANCE.
WARNING: DO NOT PLACE CLOTHING
OR OTHER FLAMMABLE MATERIALS
ON OR NEAR THIS APPLIANCE.
AVERTISSEMENT: SURVEILLER LES
ENFANTS. GARDER LES VÊTEMENTS,
LES MEUBLES, L'ESSENCE OU AUTRES
LIQUIDES À VAPEUR INFLAMMABLES
LOIN DE L'APPAREIL.
OPERATION AND CARE OF YOUR
APPLIANCE
Appliance operation may be controlled by the
following means: the factory provided modesty
panel-mounted ON-OFF control switch, an optional wall-mounted ON-OFF switch or optional
remote control.
The modesty panel mounted ON-OFF control
switch is located behind the control compartment access panel, below the appliance front
glass enclosure panel. See
Hinge
Pin
ON/OFF
Switch
Piezo Ignitor
Control Compartment Access -
Millivolt Control Valve Shown
Figure 1
Figure 1.
Gas Valve
Control
Compartment
Access panel
Modesty Panel
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
3
Gas Controls/Control Compartment Access
The gas controls can be found behind the
control compartment access panel.
To open the control compartment access panel,
actuate the spring-loaded magnetic catches
securing the panel, by gently depressing the
outer top corners of the panel until the catches
"pop" the door free, allowing it to swing out and
down to open.
On millivolt systems, the piezo ignitor, Hi/Lo
flame adjustment knob, and pilot and main gas
ON/OFF control knob are located on the modesty panel. On both millivolt and electronic
systems the gas valve is located behind the
modesty panel. Refer to
Remove the bottom control compartment access panel by compressing the spring-loaded
hinge pin on the left side until it disengages
from the left cabinet panel hole. Pull the panel
away from the fireplace.
Once the control compartment access panel
has been removed, the modesty panel can be
removed as follows: pull the bottom right
corner of the modesty panel out slightly to
disengage the snap-fit feature; lift the modesty
panel by the tab on the panel's right end, pull
the right end of the panel away from the
cabinet and then pull the panel diagonally out
of the left side cabinet panel slots. (In the
above procedure, reverse the words "left" and
"right" for EDCR-2 models).
Variable Flame Height Adjustment
TPTH TP TH
Figure 1.
Manifold Pressure Port
I
H
L
O
W
P
I
L
O
T
Inlet Pressure Port
IN
OUT
F
F
O
P
I
L
it
O
T
O
N
Remove the modesty panel carefully, so that
none of the wires become loose or disconnected. Now complete access to the gas control valve and its related controls is attainable.
To ease door closure, depress the catches to
place them in their retracted position, then
close the door.
Operation of millivolt and electronic gas control systems are different. Before lighting and
operating your appliance determine if you have
a millivolt or electronic appliance.
Figure 1 on page 4
for access to the gas
Refer to
control valve. Millivolt appliances will be fitted
with the gas control valve shown in
Figure 2
Appliances with electronic systems will be
fitted with the electronic valve shown in
Figure 3
. Familiarize yourself with the gas
control valve that your appliance uses.
Millivolt Appliances -
To light millivolt appliances refer to the detailed lighting instructions found on
(English) and page 14
(French). Millivolt ap-
page 13
pliance lighting instructions may also be
found on the pull out lighting instruction
labels attached to the gas control valve.
Millivolt appliances are fitted with a burner ON/
OFF control switch (rocker switch). See
1 on page 3
for its location. Once the pilot is lit,
Figure
the ON/OFF rocker switch will control the appliance ON/OFF operation. To operate: Toggle the
switch between its ON and OFF positions.
OFF
ON
ON/OFF Switch
IN
PSI
Manifold Pressure Port
CONTROL
IG
N
ITE
R
Honeywell Electronic
Figure 3
If your millivolt appliance is equipped with an
.
optional wall-mounted ON/OFF switch or remote control kit and the pilot is lit, the appliance
main burner may be turned on and off with the
wall switch or remote control.
Electronic Appliances -
To light electronic appliances refer to the detailed lighting instructions found in both English and French on
instructions respectively. Electronic appliance
lighting instructions may also be found on the
pull out lighting instruction labels attached to
the gas control valve.
Electronic appliances are fitted with a ON/OFF
burner control switch (rocker switch). See
Figure 1 on page 3
tronic system will go through the whole lighting sequence automatically once the rocker
switch is toggled to the ON position.
If your electronic appliance is equipped with an
optional wall-mounted ON/OFF switch or remote control kit the appliance main burner may
be turned on and off with the wall switch or
remote control.
pages 15 and 16
for its location. The elec-
Inlet
Pressure
Port
Electronic
Gas Control
Valve
Gas Valve
of these
Main Gas
SIT Millivolt Gas Valve
Control Knob
Note: The piezo ignitor is located on the modesty panel - see Figure 1.
Figure 2
4
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Variable Flame Height Adjustment
( Millivolt Appliances only)
1. All Millivolt appliances are equipped with a
variable gas control valve. Flame height for
these models may be adjusted through a range
between fixed low and high settings while the
appliance is in operation.
Adjust the flame height as desired after lighting
the appliance by rotating the variable adjustment control knob located on the front of the
valve
(refer to Figure 2)
provided to this knob so that the adjustment
may be made at the modesty panel.)
2. When lit for the first time, this appliance will
emit a slight odor for 14 hours. This is due to the
“burn-in” of internal paints and lubricants used
in the manufacturing process.
3. Keep lower control compartment clean by
vacuuming or brushing at least twice a year.
More frequent cleaning may be required due to
excessive lint from carpeting, bedding materials, etc. It is important that control compartments, burners and circulating air passageways of the appliance be kept clean.
4. Always turn off gas to the pilot (millivolt
appliances) and let the unit cool down before
cleaning. Before re-lighting, refer to the lighting instructions in this manual. Lighting in-
structions may also be found on the pull out
lighting instruction labels attached to the
gas control valve.
5. Always keep the appliance area clear and
free from combustible materials, gasoline and
other flammable liquids.
6. Remember, Millivolt appliances have a continuous burning pilot flame. Exercise caution
when using products with combustible vapors.
7. Clean the front glass enclosure only when
necessary and when the unit is cool. Wipe
surface with clean, dampened, soft cloth. Follow with dry, soft towel as desired. Take care
not to scratch the glass surface.
. (An extension is
WARNING: DO NOT USE ABRASIVE
CLEANERS. NEVER CLEAN THE GLASS
WHEN IT IS HOT.
CAUTION: DO NOT TOUCH THE FRONT ENCLOSURE GLASS WITH YOUR HANDS WHILE
THE FIREPLACE IS IN USE.
Outside Combustion Air Controls
Many appliances are equipped, when installed,
with an outside (make-up air) vent system
that is designed to provide the appliance with
outside make-up air for combustion when in
operation. The outside air control lever for
the outside air system is standard on all
appliances but should not be operated if the
complete system is not installed. Refer to
Figure 4
system is installed, the installer will remove
the securing screw from the combustion air
control lever located on the right side (EBST2, EBPF-2 and EBCL-2), or left side (EBCR-2)
of the fireplace opening.
If the securing screw has not been removed and
you have reason to believe that you have a
complete outside air system, contact your distributor to have your appliance inspected for
the presence of the complete system. DO NOT
assume that you have this system in place.
. When the complete outside air vent
Outside Air Control Lever with Stop Behind
Securing Screw
Outside Air Shutter in the
Closed Position
Control Compartment Access Panel
Outside Air Control Lever
and Securing Screw Location
(EBST-2, EBPF-2 and EBCR-2 Units Shown)
Figure 4
WARNING: DO NOT OPERATE THE SHUTOFF
LEVER UNLESS A COMPLETE OUTSIDE
COMBUSTION AIR SYSTEM HAS BEEN INSTALLED WITH YOUR APPLIANCE.
To open the outside air shutter, open the
botttom control access panel, reach into the
gap between the firebox bottom and the
modesty panel, and pull the outside air control lever all the way out. The outside air
shutter should be fully open when the fireplace is in use and completely closed when
the fireplace is not being used. Closing it
when not in use will prevent outside cold air
from entering the dwelling.
Venting Action and Safety Limit Operation
If you suspect that the appliance is not venting
properly, or you notice windows fogging or
sweating, you may want to conduct the following spillage test:
1 - Place unit in its normally-operated con-
dition, that is, with the glass enclosure panels in place.
2 - Close all doors and windows in the
room. Turn on all exhaust fans in the house.
3 - Light the appliance.
4 - Wait 15 minutes.
5 - To check for venting action, start by
holding a smoke producing device within an
inch of one edge (side edge, not top or
bottom edge) of one glass enclosure panel.
The smoke should be drawn toward the edge
of the glass enclosure panel. Continue the
test by moving the smoke producing device
along the entire length of both side-edges of
the glass door. Repeat the test for all glass
enclosure panels.
6 - If the smoke is not drawn towards the
edges of the glass door turn off the appliance and call a qualified service technican.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
5
Manual-Reset Safety Limit Switch
This appliance is equipped with a manualreset blocked flue safety limit switch. Refer to
Figure 5
for its location. If, during appliance
operation, the flame goes out (independently
of the burner on/off wall switch), it may be due
B - To access the blocked flue safety switch
when top radiant panel is covered with noncombustible material:
Note: This procedure should only be performed
by a qualified service technician.
to the operation of this safety limit switch.
First allow the appliance to cool, then reset
the safety switch by pushing the red reset
button on it.
1 -Lower bottom hinged panel on the control side of the fireplace. Remove the modesty panel and glass enclosure panel as
described on page 8, under "Remove the
A - To access the blocked flue safety switch
when top radiant panel is not covered with
non-combustible material:
front glass enclosure panel as follows:",
Steps 2, 3, 4, 5 and 6.
2 -Remove the side baffle securing screws
(5) and then remove the baffle.
1 - Lift up and remove top radiant panel/
eyebrow assembly on the control side of
unit.
2 - Reach between the cabinet side and the
firebox side wall and locate the blocked flue
safety switch.
3 - Push the red reset button on the switch.
3 -Remove the safety switch bracket secur-
ing screws (2), and pull the switch/bracket
assembly through the side panel slot.
4 -Push the red reset button on the switch.
5 -Reinstall the switch/bracket assembly.
6 -Reinstall the side baffle.
7 -Reinstall front glass door.
8 -Raise the bottom hinged panel.
The applilance should then relight and remain
lit. If this does not occur, turn off the appli-
ance and call a qualified service technician.
The appliance should then relight and remain
lit. If this does not occur, check unit for a
blocked flue condition.
SAFETY SWITCH LOCATION (EBCL-2 SHOWN)
EBST-2 and EBPF-2 Safety Switch Location Also as Shown; EBCR-2 Location
on Left End of Fireplace, EBBAY Location on The Rear of Fireplace.
FIREBOX SIDE BAFFLE SECURING SCREW
FIREBOX BOX
SIDE WALL
FIREBOX SIDE BAFFLE
MANUALLY-RESET
SAFETY LIMIT SWITCH
Maintenance
The appliance and venting system should be
thoroughly inspected before initial use and at
least annually by a qualified service technician. However, more frequent periodic inspections and cleanings should be performed by
the homeowner. Homeowner must contact a
qualified service technician at once if any
abnormal condition is observed.
Refer to the maintenance schedule for maintenance tasks, procedures, periodicity and by
whom they should be performed. Always
verify proper operation of the appliance after
servicing.
IMPORTANT: TURN OFF GAS AND ANY ELECTRICAL POWER BEFORE SERVICING THE
APPLIANCE.
Front Glass Enclosure Panel, Removal
and Installation.
WARNING: NEVER OPERATE THE APPLIANCE WITHOUT THE GLASS ENCLOSURE
PANELS IN PLACE AND SECURE. DO NOT
OPERATE APPLIANCE WITH FRONT GLASS
CRACKED, BROKEN OR MISSING. REPLACEMENT MUST BE DONE BY A LICENSED OR
QUALIFIED SERVICE TECHNICIAN.
These fireplaces are designed to operate only
with the glass enclosure panels properly installed. Generally the glass enclosure panels
should not be removed except to gain access
to the components within the firebox, and the
appliance may only be operated without the
front glass enclosure panel in place for very
brief periods of time during initial appliance
checkout and adjustment.
During this appliance checkout and adjustment
period, a potential safety hazard exists - EXERCISE EXTREME CAUTION to prevent the occurrence of any burn injuries from the exposed
flames or hot surfaces. Also note, that while the
front glass enclosure panel (or any of the panels)
is removed, the flame appearance will appear to
be smaller than normal.
WARNING: HANDLE THE GLASS WITH EXTREME CARE! TEMPERED GLASS IS SUSCEPTIBLE TO DAMAGE (SCRATCHES, FOR
SAFETY SWITCH
BRACKET SECURING SCREW
TOP RADIANT PANEL
AND EYEBROW
Figure 5
6
CABINET SIDE WALL
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
EXAMPLE) – HANDLE GLASS DOOR
(GLASS ENCLOSURE PANEL) GENTLY
WHILE REINSTALLING IT.
Maintenance Schedule
Annually (Before the onset of the Burning Season)
Maintenance Task Accomplishing Person Procedure
Inspecting/Cleaning Burner, Logs
and Controls
Check Flame Patterns and Flame Height
Inspecting/Cleaning Pilot Burner and the Two
Main Burners
Checking Vent System
Appliance Checkout
Periodically (After the Burning Season)
Qualified Service Technician
Qualified Service Technician
Qualified Service Technician
Qualified Service Technician
Qualified Service Technician
Inspect valve and ensure it is properly operating. Check piping for leaks. Vacuum the control compartment, fireplace logs and burner
area.
Refer to
Figure 8 on page 8
and verify that the
flame pattern and height displayed by the
appliance conforms to the picture. Flames
must not impinge on the log set.
Refer to
Figure 1 on page 8 (SIT) or Figure 12
on page 9 (Honeywell)
. Remove any surface
build-up on pilot and burner assembly. Clean the
pilot nozzles, ignitor/flame rod and hood with a
soft brush. Ensure the pilot flame engulfs the
flame sensor as shown.
Inspect the vent system at the top and at the
base (within the firebox) for signs of blockage
or obstruction. Look for any signs of dislocation of the vent components.
Perform the appropriate appliance checkout
procedure detailed in this manual.
Maintenance Task Accomplishing Person Procedure
Cleaning Firebox Interior
Check Flame Patterns and Flame Height
Checking Vent System
Cleaning Glass Enclosure Panels
Homeowner
Homeowner
Homeowner
Homeowner
Carefully remove logs, vermiculite and black and
gray ceramic fiber chunks. Vacuum out interior of
the firebox. Clean firebox walls and log grate.
Replace logs, vermiculite and black and gray ce-
page 8
ramic fiber chunks as detailed on
Refer to
Figure 8 on page 8
.
and verify that
the flame pattern and height displayed by the
appliance conforms to the picture. Flames
must not impinge on the log set.
Inspect the vent system at the top and at the
base (within the firebox) for signs of blockage or obstruction. Look for any signs of
dislocation of the vent components.
Clean as necessary following the directions
provided in this manual. DO NOT TOUCH OR
CLEAN GLASS WHILE IT IS HOT.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
7
WARNING: DO NOT ATTEMPT TO SUBSTITUTE THE MATERIALS USED ON THESE
DOORS, OR REPLACE CRACKED OR BROKEN GLASS WITH ANY MATERIALS OTHER
THAN THOSE PROVIDED BY THE APPLIANCE MANUFACTURER.
THE GLASS DOORS OF THIS APPLIANCE MUST
ONLY BE REPLACED AS A COMPLETE UNIT AS
PROVIDED BY THE MANUFACTURER. DO
NOT ATTEMPT TO REPLACE BROKEN,
CRACKED OR CHIPPED GLASS SEPARATELY.
Refer to
Figure 6
and remove the front glass
enclosure panel as follows:
1. Remove the top bustle, and the top louver
assembly or radiant panel. Then remove the
bottom bustle.
2. Open the control compartment access panel.
To open the control compartment access panel,
actuate the spring-loaded magnetic catches
securing the panel, by gently depressing the
outer top corners of the panel until the catches
"pop" the door free, allowing it to swing out and
down to open.
3. Remove the bottom control compartment
access panel by compressing the spring-loaded
hinge pin on the left side until it disengages
from the left cabinet corner post hole. Pull the
panel away from the fireplace.
Lower Compartment Door and Hinge
Modesty Panel
Glass
Enclosure
Panel
Latch
Bottom Vee-flange
(Glass Enclosure
Panel Frame)
EBST-2 SHOWN
Top Flange
(Glass Enclosure
Panel Frame)
Front Glass
Enclosure Panel
Firebox Floor
Figure 6
5. Locate the latch at the top of the control
compartment. To disengage the latch from the
bottom vee-flange of the glass enclosure panel,
reach for the handle located towards the back
of the latch and pull the handle down towards
the front of the unit.
6. Swing the bottom of the door out and raise
it slightly to lift the top flange of the door frame
away from the appliance.
4. Reinstall the modesty panel by inserting the
tongues on the left side of it into the slots on
the left side cabinet panel. Swing the right side
of the modesty panel towards the unit. Engage
the hook on the right side of the modesty panel
with the right side cabinet panel slot. Gently
press the bottom right corner of the modesty
panel to engage the snap-fit feature.
(The left and right designations used here are
reversed in EBCR-2 applications.)
5. Reinstall the bottom control compartment
access panel by inserting the right side locating pin into the right side cabinet panel and
then the left side spring-loaded pin into the left
side cabinet panel.
6. Reinstall the top and bottom bustle, and the
top louver assembly or radiant panel.
Burner Adjustments
Note -
The air shutter for the burner primary air
opening is factory-set. Do not adjust the factory-set position. The factory-set position is
shown in Figure 7.
*Air Shutter
Opening
Burner
Venturi
Tube
Orifice
4. Once the control compartment access panel
has been removed, the modesty panel can be
removed as follows: pull the bottom right
corner of the modesty panel out slightly to
disengage the snap-fit feature; lift the modesty
panel by the tab on the panel's right end, pull
the right end of the panel away from the
cabinet and then pull the panel diagonally out
of the left side cabinet panel slots. (In the
above procedure, reverse the words "left" and
"right" for EBCR-2 models).
Remove the modesty panel carefully, so that
none of the wires become loose or disconnected. Now complete access to the gas control
valve and its related controls is attainable.
To install the front glass enclosure panel,
proceed as follows:
1. Visually inspect the gasket on the backside
of the panel. The gasket surface must be clean,
free of irregularities and seated firmly.
2. Position the glass enclosure panel in front
of the firebox opening at a 45 degree angle and
engage the top flange over the lip at the top of
the firebox opening.
3. Swing the glass enclosure panel down and
back. Ensure the gasket seats evenly as the
panel draws shut. Engage the Vee-flange at
the bottom of the panel with the latch and then
close the latch to secure the panel.
*Note - Do Not Adjust the Factory-Set Position.
Each of the two air shutters (one for each burner) are
open the amount shown in the table, below.
RENRUBNIAM
GNITTESRETTUHSYROTCAF
saGlarutaN
sledoM
sehcni
)mm(
enaporP
saG
sehcni
)mm(
2-TSBE
2-FPBE
2-RCBE
61/1)5.1(61/5)8(
2-LCBE
YABBE
Figure 7
8
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Loading...