Lennox 506033-16 User Manual

HEARTH PRODUCTS

KITS AND ACCESSORIES

P/N 506033-16 Rev. A, 05/2009

INSTALLATION INSTRUCTIONS FOR INSTALLING PEDESTAL KITS FOR USE WITH COUNTRY COLLECTION™ FREESTANDING WOODSTOVES

KIT CONTENTS

Please ensure that all these parts are included

1 ea. Pedestal Assembly 2 ea. 3/8”-16 x 3/8” Hex Bolts 2 ea. 3/8” Flat Washers 1 ea. Instruction Sheet

Pedestal Kits (all models)

Cat. No. Model Where Used

71108 WS-PED S160, SA160

71113 WL-PED SS210, ST210, S260, ST310

TOOLS NEEDED

9/16” Open End Wrench or Ratchet with 9/16” Socket

GENERAL INFORMATION

If you encounter any problems, need clariﬁcation of these instructions or are not qualiﬁed to properly install this kit, contact you local distributor or dealer.

INSTALLATION INSTRUCTIONS

Step 1. Remove the stove and pedestal from the cartons, if packaged,

upon receipt and check for any damaged or missing parts.

Step 2. Carefully put the stove on pedestal with the open end of the

pedestal facing the rear (see Figure 1). DO NOT LEAVE THE

STOVE UNATTENDED UNTIL IT IS BOLTED SECURELY TO THE PEDESTAL. IT COULD FALL CAUSING SERIOUS INJURY OR DAMAGE.

Step 3. Line up the holes in the brackets on the pedestal with the

threaded holes in the bottom of the stove. Using a 9/16” wrench or socket, secure the stove to the pedestal with the two 3/8” long bolts and 3/8” standard washers. Be sure to see that the stove is mounted squarely on the pedestal before tightening the two bolts securely.

Step 4. When installing a pedestal on this stove you MUST plug the four

leg mounting bolt holes, located on the bottom of the stove in the four corners, with the bolts that were used to mount the shipping legs. FAILURE TO INSTALL THESE FOUR BOLTS PROPERLY

WILL RESULT IN REDUCED CONTROL OF THE STOVE’S COMBUSTION SYSTEM! Caution: The two rear bolts should

not be installed more than two full rotations to prevent lifting the bricks off the bottom of the stove.

WOODSTOVE PEDESTAL KITS

Read this instruction sheet in its entirety before beginning the installation.

ALL WARNINGS, PRECAUTIONS AND INSTRUCTIONS IN THE INSTAL LATION AND OPERATION MANUAL PROVIDED WITH THE APPLIANCE APPLY TO THESE INSTRUCTIONS.

Check the contents of the kits upon receipt and check for any damaged or missing parts. If there is hidden damage, notify your freight company or Lennox Hearth Products dealer immediately.

CAUTION: Wear gloves during installation in case of sharp edges on the stove.

Manufactured (Mobile) Homes

In manufactured homes, this appliance must be bolted to the ﬂoor and properly grounded to the chassis. An outside air kit (order Cat. No. 71112) is also required. See the Installation and Operation Manual for details and additional requirements for manufactured home installations. Also see See steps 5, 6 and 7 on Page 2.

NOTE: DIAGRAMS AND ILLUSTRATIONS ARE NOT TO SCALE.

FRONT

Pedestal

REAR

Figure 1

MANUFACTURED HOME REQUIREMENTS

Step 5. Install the Outside Air Kit per the instructions provided in kit

(order cat. no. 71112).

Step 6. In Manufactured (mobile) Home installations the stove must

be bolted to the ﬂoor through the pedestal base, on both sides, using 1/4” Ø lag screws (not provided). The lag screws must be of an adequate length to extend through the hearth pad and into the ﬂoor. Seal any irregularities with silicone sealer.

Step 7. If installed in a manufactured (mobile) home, the heater must be

grounded to the chassis with a #8 AGW copper wire or equivalent.

SEE THE INSTALLATION AND OPERATION MANUAL FOR ADDITIONAL REQUIREMENTS FOR MANUFACTURED (MOBILE) HOME INSTALLA TIONS.

NOTE: DIAGRAMS AND ILLUSTRATIONS ARE NOT TO SCALE.

Lennox Hearth Products reserves the right to make changes at any time, without notice, in design, materials, speciﬁcations, prices and also to discontinue colors, styles and products. Consult your local distributor for ﬁreplace code information.

P/N 506033-16 REV. A 05/2009

1110 West Taft Avenue • Orange, CA 92865