Lenmar OmniSource 10-12 Owner's Manual

®

®

10•12

OmniSource

BATTERY CHARGER and RECONDITIONER

BCR10

OWNER'S MANUAL

Please read before using this system.

IINNTTRROODDUUCCTTIIOONN

Thank you for purchasing LENMAR's OmniSource
virtually all 9.6V, 10V, and 12V full size and VHS-C camcorder batteries. The OmniSource 10•12
is an AC/DC Battery Charger and Reconditioner. Two methods of charging are available. The
Discharge/Charge mode for nickel cadmium batteries will automatically discharge and then quick
charge batteries. The discharging process eliminates any battery memory, thereby allowing the
battery to be charged to its maximum capacity. The second method is the quick charge function,
which is especially useful for NoMEM™ batteries and lead acid batteries where discharging
should be avoided.

The OmniSource 10•12 allows you to Charge or Discharge/Charge your batteries through a
standard household AC outlet or on the road from a 12V cigarette lighter socket.

The OmniSource 10•12 is a complete, convenient system to refresh and charge your full size and
VHS-C camcorder batteries.

TThhee ffoolllloowwiinngg ssttaatteemmeenntt iiss rreeqquuiirreedd iinn tthhee ssttaattee oof
bbyy tthhee MMaatteeeell EEnnvviirroonnmmeennttaall JJuussttiiccee FFoouunnd

WWAARRNNIINNGG:: HHaannddlliinngg tthhee ccoorrdd oonn tthhiiss

CCaalliiffoorrnniiaa ttoo ccaauussee bbiirrtthh ddeeffeeccttss o

®

®

10•12. The OmniSource 10•12 can charge

f CCaalliiffoorrnniiaa ppuurrssuuaanntt ttoo tthhee sseettttlleemmeenntt ooff aann aaccttiioo

daattiioonn aaggaaiinnsstt mmuullttiippllee eelleeccttrroonniiccss aanndd aapppplliiaannccee mm

pprroodduucctt wwiillll eexxppoossee yyoouu ttoo lleeaadd,, aa cchheemmiiccaall kknnoowwnn

orr ootthheerr rreepprroodduuccttiivvee hhaarrmm.. WWaasshh hhaannddss aafftteerr hhaannddll

aannuuffaaccttuurreerrss..

ttoo tthhee ssttaattee ooff

iinngg..

nn bbrroouugghhtt

OOPPEERRAATTIINNGG IINNSSTTRRUUCCTTIIOONNSS
MMOODDEELL BBCCRR1100

AAUUTTOOMMAATTIICC DDIISSCCHHAARRGGEE TTOO RREECCHHAARRGGEE OOFF BBAATTTTEERRYY

1. If you wish to automatically discharge and recharge a battery, engage the battery onto the OmniSource base unit.
(Refer to Battery Placement and Compatibility List to determine which side your battery fits on.)

2. Plug either the AC (110V) or DC (Cigarette Plug) into "input" jack. The Red LED light will illuminate to indicate power
is on.

3. Push the Discharge button. The Yellow LED light will illuminate to indicate the battery is being reconditioned.
Memory, if any is being eliminated. Important: Do not discharge NoMEM™ or Lead Acid Batteries.

4. When the battery is fully discharged, the Yellow LED light will go out and the Green LED will illuminate, indicating
battery is now being charged.

5. When the Green LED light goes out, it indicates battery is fully charged. It is recommended to remove battery from
unit.

6. Battery is now ready to be used.

NOTE: Unit will buzz if discharge button is pushed and battery is not properly connected.

CCHHAARRGGEE OONNLLYY FFEEAATTUURREE FFOORR NNooMMEEMM AANNDD LLEEAADD AACCIIDD BBAATTTTEERRI

1. Plug either the AC (110V) or DC (Cigarette Plug) into "input" jack. The Red LED light will illuminate to indicate power
is on.

2. Engage the battery onto the OmniSource base unit. (Refer to Battery Placement and Compatibility List to determine
which side your battery fits on.)

3. The Green LED light will illuminate, indicating battery is now being charged.

4. When Green LED light goes out, it indicates battery is fully charged. Remove battery from unit.

55.. BBaatttteerryy iiss nnooww rreeaaddyy ttoo bbee uusseedd..

DISCHARGE ONLY FEATURE - FOR NiCd BATTERIES ONLY

To discharge a battery without automatically charging, does not require a power source.

1. Engage the battery onto the OmniSource base unit. (Refer to Battery Placement and Compatibility List to determine
which side your battery fits on.)

2. Push the discharge button. The Yellow LED light will illuminate to indicate battery is being reconditioned. Memory, if
any is being eliminated.

3. When the battery is fully discharged, the Yellow LED light will go out.

4. Remove the battery from the unit.

NOTE: Unit will buzz if discharge button is pushed and battery is not properly connected.
BATTERY PLACEMENT AND BATTERY COMPATIBILITY LIST
Slot "A" ON TOP

Manufacturer Battery Model #

Mathes:

Lenmar: PAN88, PBA50, LBA6500

Magnavox: AR8378BK01, V80039BK01, V80086BK01,
Panasonic: LCS2012, LCS2312, PV-BP50, PV-BP88, VW-VB30,

Quasar: VE-257, VE-258, VE-55A

Sylvania: AR8378BK01, AR8395BK01, V80039BK01,

NOTE: May fit additional makes and models of equivalent 12V batteries.

For placement onto unit, slide the battery in the angled slot with contacts side going in first, facing down.

Canon: BP-101A, BP-100, BP30/A, BP-31, BP-32, BT-30A

Curtis

Sears: 5399, 53991

Zenith: VAC-904, VAC-907

EA13P60, VSBS0016

GE: 1CVA125, 1CVA155, 1CVA156

V80096BK01
VW-VB31, VW-VBM7E

V80086BK01, V80096BK01

IEESS