The Pilot carries a one year warranty on the meter and transmitter.
Batteries are not warranted. Contact our Customer Service Department to
report any problems. When calling, please be prepared to provide the
customer service representative with the following information: Your
name, the serial number of the inoperable unit, and the date(s) of
purchase for the meter. If warranty replacement parts are shipped to you,
you may be required to return the inoperable part.
LeMond Fitness Inc. neither makes, assumes nor authorizes any
representative or other person to make or assume for us, any other
warranty whatsoever, whether expressed or implied, in connection with
the sale, service, or shipment of our products. We reserve the right to
make changes and improvements in our products without incurring any
obligation to similarly alter products previously purchased. In order to
maintain your product warranty and to ensure the safe and efficient
operation of your cadence meter, only authorized replacement parts can
be used. This warranty is void if parts other than those provided by
LeMond Fitness are used.
SPECIFICATIONS
Cadence Meter
Heart Rate Range:30 to 240 bpm (beats per minute)
Heart Rate Accuracy:± 4 bpm
Battery:2 AA batteries
Battery Life:6 months to 1 year, depending on usage
Transmitter
Emitted Frequency:122 kHz
Battery:3 AA batteries
Battery Life:6 months to 1 year, depending on usage
Page 5
CONTENTS
Description7
Installation to the RevMaster9
Display Window13
Quick Start Program15
Custom HR Training and Calorie Calculation16
Key Functions18
Cadence Training20
Troubleshooting23
○○○○○○○○○○○○○○○○○○○○○○○○○
Console9
Transmitter10
Magnet12
○○○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○
○○○○○○
Appendix
FCC Compliance25
○○○○○○○○○○○○○○○○
Changing the Console and Transmitter
Codes26
Dip Switch Codes27
Console Codes28
○○○○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○○
NOTE:
•Press any key to turn on the Pilot console.
•Never disassemble the console or transmitter asit
can not be reassembled.
•The console is water resistant, not water proof.
Do not deliberately place it in water.
•To clean the console, wipe it off with a clean rag
sprayed with diluted household cleaner.
Page 6
DESCRIPTION
The Pilot assembly consists of a console, a magnet, and a
transmitter. A sensor in the transmitter counts the number of
times a magnet mounted in the right crank passes the sensor.
The transmitter will then send a coded RF (radio frequency)
signal to the console containing the measured values.
The console has inboard receivers that pick up the signals
from the transmitter and from telemetry (chest strap) heart rate
signals. The heart rate is then shown in the display window. The
console will track cadence (RPMs), speed (MPH/KPH), time,
distance, and caloric expenditure.
The console and the transmitter use AA batteries as a
source of power. Install the supplied batteries in the console and
in the transmitter prior to using.
Console Battery Installation:
1.Loosen the battery cover screw remove the battery
cover from the console.
2.Insert 2 AA batteries into the battery compartment
and reinstall the battery cover.
Page 7
DESCRIPTION
Transmitter Battery Installation:
1.Remove the battery cover from the transmitter.
2.Install 3 AA batteries in the battery compartment
and reinstall the battery cover.
NOTE:
•Excessive use of the back light [ ]will drain
the console batteries prematurely.
•Expected life of the console batteries is 6
months to 1 year.
•If the console battery power is low, then “BATTLOW” will be shown in the display window for
2 seconds after the display is turned on to inform
you to change the console batteries.
•Expected life of the transmitter batteries is 6
months to 1 year.
Page 8
INSTALLATION OF THE PILOT
THE CADENCE METERCANONLYBEINSTALLEDONA
LEMOND REVMASTERBIKE.
To install the meter, the following tools are needed:
•Philips Screwdriver
•4-mm Hex Key (supplied)
Console Installation:
1.Ensure that the batteries are installed in the console and
the console turns on.
2.Spread the bottom of the console clamp apart and
clamp itback together over the top center of the handle
bar.
3.Insert a mounting screw into each hole and use a
4-mm hex key to tighten the screws.
Handlebar
Console
Clamp
Battery Cover
Screw
Mounting Screws
Page 9
Loading...
+ 20 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.