Lemon Duo339 Super, Duo405 User Manual

Page 1

PN: 5839003068

Page 2

While all efforts have been made to ensure the accuracy of all contents in this manual, we assume no liability for errors or omissions or statements of any kind in this manual, whether such errors or omissions or statements resulting from negligence, accidents, or any other cause. The contents of this manual are subject to change without notice.

Protect our environment! We strive to produce products in compliance with global environmental standards. Please consult your local authorities for proper disposal.

Note: User’s Manual is Just to guide the user about the functionality of the phone. This dose not seems any certificate of technology. Some functions may very due to modifications and up gradations of software or due to print mistake.

SAFETY PRECAUTIONS

Before using your phone, please read the following important information to eliminate or reduce any possibility of causing damage and personal injury.

Do not use wireless phones while driving.

Switch off wireless devices in aircraft. The signal may cause interference. Using them on aircraft is illegal.

Do not use mobile phones where blasting is in progress. Follow regulations and rules strictly.

Do not use mobile phones at a refueling point. Don’t use near fuel or chemicals

Follow regulations or rules in hospital and health care facilities. Switch phone off near medical equipment.

All wireless devices may get interference that could affect performance.

Only qualified service personnel can install or repair this device.

Use only approved accessories and batteries.

Use only in normal position. Do not expose your phone to extreme high temperatures above +60℃（+140°F）. Do not use anything static to clean

your phone. Ensure the phone is turned on and in service. Enter the emergency number, then press Pick Up key. Give your location. Do not end the call

until told to do so.

Improper use will invalidate the warranty! These safety instructions also apply to original accessories.

Page 3

Table of Content

GENERAL INFORMATION ........................................................................................ 4

Antenna ................................................................................................................ 4

Network Service.................................................................................................... 4

Accessories .......................................................................................................... 4

Privacy.................................................................................................................. 4

KNOW YOUR MOBILE PHONE................................................................................. 4

Positions of Phone Keys ....................................................................................... 5

Display Screen...................................................................................................... 6

IMPORTANT INFORMATION..................................................................................... 7

Use of Passwords................................................................................................. 7

Battery Information ............................................................................................... 7

Usage & Maintenance........................................................................................... 8

Emergency Calls................................................................................................... 9

GETTING STARTED.................................................................................................. 9

First Call ............................................................................................................... 9

Mounting the SIM Card......................................................................................... 9

Mounting the T-Flash Card.................................................................................. 10

Charging the Battery............................................................................................11

Switching Your Phone On/Off...............................................................................11

Waken Up Your Phone.........................................................................................11

CALLING ................................................................................................................. 11

Making Calls ........................................................................................................11

Answering Calls.................................................................................................. 12

Options in Call .................................................................................................... 12

GUIDE TO MENU OPERATIONS............................................................................. 12

Phone Book........................................................................................................ 12

Messaging .......................................................................................................... 13

Call Center.......................................................................................................... 14

Organizer............................................................................................................ 15

Multimedia .......................................................................................................... 17

Fun & Games ..................................................................................................... 18

Opera Mini .......................................................................................................... 19

Lemon Twist:....................................................................................................... 19

Settings .............................................................................................................. 21

Services.............................................................................................................. 24

File Manager....................................................................................................... 24

APPENDIX ............................................................................................................... 25

Appendix A: Guidance on Entry Methods............................................................ 25

Appendix B: Troubleshooting .............................................................................. 26

Appendix C: FCC Statement............................................................................... 26

WAP/MMS Settings································································································· 27

Page 4

GENERAL INFORMATION Antenna

Use of other antenna devices could damage your mobile phone and reduce performance. Your phone has a built-in antenna. Don’t touch the antenna area unnecessarily when the phone is switched on. Contact with the antenna affects call quality and may cause the phone to operate at a higher power level than otherwise needed.

Network Service

A lot of features described in this manual are called network service. They are special services provided by wireless service providers. You should subscribe to these services from your home service provider and learn instructions on uses before you select the network you want to use.

Accessories

Li-Ion battery is the manufacturer-approved rechargeable battery available for your phone. May be some batteries performs best after several full charge/discharge cycles. Use only batteries, chargers and accessories approved by the phone manufacturer for use with this particular model. The use of any other types will invalidate any approval or warranty applying to the phone, and may be dangerous. Please consult with your dealer for availability of approved accessories.

Privacy

The shoot or recording of photos, images or sounds privately may be prohibited by law and/or subject to criminal prosecution. We recommend you to be responsible and respectful of privacy laws when you are taking photos, or doing records.

KNOW YOUR MOBILE PHONE

Page 5

Positions of Phone Keys

1. Right/left Key 10. OK key

2. Up/down Key 11. [ * ] Key

3. Left Soft Key 12. [ # ] Key

4. Right Soft Key 13. USB connecter

5. SIM2 pick up key 14. Camera

6. Music shortcuts key 15. Speaker

7. SIM1 Pick Up Key 16.FM antenna

8. Hang Up Key 17.Torch

9. Numeric Keys 18. 3.5 mm Earphone Jack

Key Name Description

SIM1 Pick Up Key

Making or answering a call. In the standby mode, press this key to access the Call Logs.

Left Soft Key

Use the left soft key to execute to functions indicated at the left of the prompt bar on the screen.

Should press it to access UI Music shortcut key

In the standby mode, press it to access Audio

player. SIM2 Pick Up

Key

In the standby mode, press it to Pick Up Key

Hang Up Key

End an ongoing call.

In the menu mode, press this key to return the

standby mode and cancel current operations.

Press this key to stop the alarm ringing once the

alarm rings.

Right Soft Key

Use the right soft keys to execute to functions indicated at the right of the prompt bar on the screen.

Selection Keys / OK Key

Scrolling options in the function list or the phone

book.

In the edit mode, direction keys are used for

moving the cursor.

In the standby mode, press direction keys to

activate a specified function.

In the standby mode long press the space Key to

activate/ deactivate Torch Light.

Numeric Keys

Used to enter numbers, letters and some special

characters.

In the standby mode, press and hold # key to

activate Silent mode;

Page 6

Display Screen

Your mobile phone has a single screen display, which consists of three main areas: The First line displays states icons, which indicate the signal strength, the remaining power of the battery, etc. The Middle lines display text and graphics, including numbers, text, animated icons and the information you enter. The Last line displays the currently available operations assigned to the left or right soft key.

States Icons

Network Signal

Fight mode

Connecting GPRS and using GPRS

Divert all Voice Calls

Auto Keypad Lock

Alarm Clock is activated

Battery States

SIM1 and SIM2 Missed Calls

SIM1 and SIM2 New Message or Message Memory Full

Message sending

SIM1 and SIM2 New MMS

MMS is busy

Roaming Startup

Wap message

Audio player

Bluetooth

Earphone plugged in

Memory card inserted

Sound States

Ring Only

Vib. Only ( Silent mode)

Vib. then Ring

Vib. and Ring

Page 7

IMPORTANT INFORMATION Use of Passwords

Your mobile phone and SIM card have various passwords. Those passwords avoid unauthorized use of your phone and SIM card. You can change PIN, PIN2 and phone password in the “Settings > Security Setup”

Phone Code

The Phone code can be used to avoid unauthorized use of your phone. The factory setting for the phone code is 0000. If phone lock is enabled, you will be asked to input the phone password when you switch on your phone.

PIN (4 to 8 digits)

The PIN (Personal Identification Number) code protects your SIM card from unauthorized use. The PIN code is usually supplied with the SIM card. When the PIN code request is enabled, the password is asked every time the phone is turned on. Three times wrong PIN input, the SIM card will be locked and you will need to use the PUK to unlock it. PUK is usually set by the network operator.

1. Enter the correct PUK to unlock the SIM card, and then enter the new PIN and press OK.

2. If you are prompted to enter the new PIN again, enter it and press OK.

3. If the PUK is correct, the SIM card will be unlocked and the PIN will be reset.

PUK (8 digits)

The PUK (Personal Unblocking Key) code is required to change a blocked PIN code. Please contact your network operator for the code. Note: Ten times wrong input in succession, the SIM card will be invalid and you need to consult with your network operator for a new SIM card.

PIN2 (4 to 8 digits)

The PIN2 code, supplied with some SIM card, is used for some functions, such as Call Cost, Fixed Dial and so on. Please consult your network operator to confirm whether your SIM card supports those services or not. Three times wrong PIN2 code input, the SIM card will be locked and you will need to use the PUK2 to unlock it.

1. Enter the correct PUK2 to unlock PIN2, and then enter the new PIN2 and press OK.

2. If you are prompted to enter the new PIN2 again, enter it and press OK.

PUK2 (8 digits)

The PUK2 code, supplied with some SIM card, is required to change a blocked PIN2 code. It may be supplied with the SIM card. If not, contact your network operator. Note: Ten times wrong input in succession, the SIM card will be invalid and you need to consult with your network operator for a new SIM card.

Barring Code

To activate call barring, you need a Barring Code. You obtain the password from your service provider.

Battery Information Charing and Discharging

 The charger is designed to be used in temperatures between 0°C to 40°C.  Do not charge the phone in wet and damp conditions.  Use only batteries approved by the phone manufacturer and recharge your battery

only with the charges approved by the manufacturer.

 We strive to produce products in compliance with global environmental standards

Page 8

 The charger meets the standard for safety of information technology equipment

and office equipment use. It must be used for this purpose only.

 Your phone is powered by a rechargeable battery. Full performance of the battery

is achieved only after two or three complete charge and discharge cycles.

 When the battery level is low, “Low Battery” will be displayed on the LCD screen. If

you have selected Alert Tone (Warning Tone of any profile in Profiles), the phone will sound the alert tone.

 When a charger is not in use, disconnect it from the power source. Do not leave the

battery connected to a charger for longer than 12 hours, since overcharging may shorten its life.

 Temperature extremes will affect the ability of your battery to charge.

Tips for Battery

 Placing the battery in hot or cold places, such as in a closed car in summer or

winter, will reduce the capacity and lifetime of the battery.

 Do not let the metal contacts on the battery touch other metal contacts. It could

short-circuit and damage the battery. Use the battery only for its intended purpose.

 Do not disassemble or modify the battery by yourself.  Do not clean the battery with water or any organic solvent.  Always keep the battery dry.  The battery can be charged and discharged many times but it will wear out as last.

When the talk and standby time is obviously shorter than normal, please change the original battery approved by manufacturer.

 Do not short-circuit the battery.  Turn off mobile phone before removing the battery.  Do not dispose of batteries in fire.  If you smell anything strange from the battery or find that the battery is overheated,

you should stop using it immediately and contact the authorized After Service Center in your region.

 If you don’t use the battery for a long time, please fully charge the battery before

you store it.

 Batteries should never be placed in municipal waste. Batteries must be recycled or

disposed of properly. Please follow local regulations for disposal of batteries.

Usage & Maintenance

To keep your product working well, take a moment to review the following usage & maintenance tips, which will help you to fulfill any warranty obligations and to enjoy this product for many years.

 Keep your phone and all its parts and accessories out of children’s reach.  Your products are not water-resistant. Keep it dry. Precipitation, humidity and

liquids contain minerals that will corrode the connectors.

 Always treat your products with care and keep it in a clean and dust-free place.  Do not expose your product to extreme high or low temperatures. Your phone

operates best in temperature between 15 °C and 25°C. Minimum and maximum temperatures recommended by the manufacturer are -10°C and 55°C.

 Do not expose your product to open flames or lit tobacco products.  Do not attempt to disassemble or modify your product. Only authorized personnel

should perform service.

 Do not drop, throw or try to bend your product.

Page 9

 Do not paint your product.  Do not use harsh chemicals, cleaning solvents, or strong detergents to clean it.  Keep anything magnetic, such as credit cards, far away from your product.  If you find that the battery has any crack, deformation or anything else, you should

stop using the battery immediately.

 If the electrolyte leak out and contact your skin or clothes, you should immediately

use soap and clean water to clean it. In case the electrolyte spatters into your eyes, you must use the clean water to wash your eyes thoroughly and go to the hospital immediately.

 If your phone or any accessory doesn’t function normally, please send them to the

nearest authorized service facility. The qualified personnel there will assist you, and if necessary, arrange for service.

Emergency Calls

This phone, like any wireless phones, operates using radio signals, wireless and landline networks which cannot guarantee connection in all conditions. Therefore, you should never rely solely upon any wireless phone for essential communications (e.g. medical emergencies). To make an emergency call: 1> Switch your phone on. Some networks may require that a valid SIM card is properly inserted in the phone. 2> Dial the official emergency number. Emergency numbers vary by location. While making an emergency call, please remember to give all information as particularly as possible. Never hand off the call please until you are given permission to do so.

GETTING STARTED

First Call

 Insert a SIM card (Switch off your phone at first, and then remove the battery).

Enter the area code and the phone number and press Pick Up Key.

Tip: Before you get started, you must insert a valid SIM card in your phone and charge

the battery first.

 SIM Card: Please refer to “Mounting the SIM Card” for more reference on

installation.

 Charging the battery: please refer to “Charging the battery” for more details.

Mounting the SIM Card

Your mobile phone number, PIN (Personal Identification Number), PIN2, PUK (Personal Unlock Key), PUK2 (Personal Unlock Key2), IMSI (International Mobile Subscriber Identity), the network information, the phonebook data, SMS (short messages) and other data are stored in your SIM card. Note: This particular phone model only supports the SIM cards of 1.8V and 3V.  Some network operators don’t offer PIN2 and PUK2, so functions using those

passwords will be unavailable.

 The SIM card and its contacts can be damaged by scratches or bending easily, so

be careful while handling, inserting or removing the card.

 Keep all miniature SIM cards out of children’s reach.

Page 10

Note: Always make sure the phone is switched off before you insert or remove the SIM card, otherwise it may damage the SIM card.

Mounting

Remove the battery cover by sliding it. Insert the SIM card, with the notch at the bottom right and the gold contacts face down, into the card slot. Align the card to the arrow sign as the following picture shows:

Replace the battery and close the cover tightly.

Note:

 If the SIM Card is installed improperly or damaged, the prompt words “Insert SIM”

will display on the screen after you switch on your phone. Remove the SIM Card and check the way that performs as pictures show, and then mount it again.

 If “Insert SIM” still appears on the screen after you have inserted the SIM correctly,

there may be something wrong with your SIM card. Please ask the network operator to repair it.

 If the screen displays that the SIM card is locked permanently, please consult with

your network operator.

Mounting the T-Flash Card

Insert the T-Flash card, with the gold contacts face down, and into the card slot. Align the card to the arrow sign as the following picture shows:

Page 11

Charging the Battery

Note: Please always keep your phone connector and charger dry.

1. Connect the connector of the travel adapter to the phone.

2. Plug the travel adapter into a proper AC wall outlet.

3. When your phone indicates that the battery is fully charged, please pull the ravel adapter out from the I/O socket of the phone.

Tip:

1. If the battery is totally empty or not enough, it may take a few minutes before the

charging indicator appears on the screen.

2. You can turn on/off, and use the phone while charging.

Warning: Make sure that the standard voltage/power of the place where you charge the battery matches with the rated voltage/power of our travel adapter.

Switching Your Phone On/Off

 Press and hold Power Key for a few seconds to switch your phone on.  If the phone ask for a phone lock code:

Enter the phone lock code, and press OK.  If the phone ask for a PIN code: Enter the PIN code, and press OK. The PIN code is usually supplied with the SIM card. Please consult your network operator for more information.  Access the standby mode. Press and hold Power Key for a few seconds to switch your phone off.

Waken Up Your Phone

 If your phone gets into far-gone standby mode (the screen goes out): Press Power Key and then you can waken up your phone.  If your phone ask for “Press Unlock and then space key”: Enter the SIM2 Pick up key and then press the space key.

CALLING Making Calls

1. Enter the phone number (with the area code)

2. Press the SIM1/SIM2 Pick Up Key to make a call.

3. Press the Hang Up Key to end a call.

Making International Calls

1. Press the + Key for the international prefix symbol +.

2. Enter the country code, area code and phone number.

3. Press the Pick Up Key to make a call.

Clear Wrong Enters

Press the right soft key to delete the last character on the screen. Hold the right soft key will clear all you entered.

Making a call from the Phone Book

1. Press the right soft key to access the Phone Book.

2. Scroll the Up/Down key to select the number you want, and press the Pick Up Key to call the number.

Last Number Redial

1. In the standby mode, press the Pick Up Key to access the Call Logs.

Page 12

2. Press the Up/Down key to reach the desired number or name and press the Pick Up Key.

Speed Dialing

You can save 8 Speed Dial Numbers you often dial to positions titled with number keys from “2” to “9” respectively. Select “Phonebook > Options > Phonebook settings > Speed dial > Set Number”, and then set “Status” on. In the standby mode, press and hold the number key to dial the corresponding number.

Adjusting the Sound Volume

During a call, you can press the up/down navigation Keys to adjust the earpiece volume.

Answering Calls

1. To answer an incoming call, press the Pick Up Keys.

2. To end or reject an incoming/ongoing call, press the Hang Up Key.

Tip: If the caller can be identified, the screen will display the caller’s name. If the caller can’t be identified, the screen will only display the caller’s number.

Options in Call

Your phone provides a number of functions that you can use during a call. During a call, you can access Hold/End single call, New Call, Phone Book, Messages, Sound Recorder and other functions.

GUIDE TO MENU OPERATIONS

All function options about the mobile phone are listed as below with brief descriptions. Press the LSK or center key to enter to Main Menu.

Phone Book

You can fast locate the number of the person you want to contact. Please enter the initial letter of the person’s name, and related records about it will display in the middle of the screen. You can locate your records by up or down key and press OK key. Options for Searched number are:

1. View: Check the details of entry.

2. Send text message: Send the text message to the searched number.

3. Send multimedia message: Send MMS to the searched number.

4. Call: Call on the searched number.

5. Edit: Edit the entry.

6. Delete: Delete the entry.

7. Copy: Copy the entry to phone memory, SIM memory or to a file.

8. Move: Move the entry from phone to SIM or vice-versa.

9. Send vCard: Send contact as text message, as MMS, via Bluetooth.

10. Add to Blacklist: Add the entry to blacklist.

11. Mark several: You can choose one or more options, and to Unmark, Send text

message, Delete marked, Unmark all operation.

12. Caller groups: The phone is programmed with five caller groups. You can make

individual setting for each group, such as rename, ring type, incoming call picture, incoming call video and each group member’s personal setting.

13. Phonebook settings: Set the phonebook in ten categories:

- Preferred storage: Select the storage, SIM1/SIM2, phone memory or all.

- Speed dial: Set the number to speed dial.

Page 13

- My vCard: You can edit the number & send your number.

- Extra number: Other numbers such as the owner number, fixed dialed numbers, service dialing number and SOS number stored on the SIM card. You can check and edit other numbers stored on the SIM card. * Note: Service number needs the support of SIM card.

- Memory status: Check the status of SIM1/SIM2 and phone.

- Copy contacts: Copy contacts from SIM1/SIM2 to phone or vice-versa.

- Move contacts: Move contacts from phone SIM1/SIM to phone or vice-versa.

- Delete all contacts: Delete all contacts from SIM1/SIM2 or phone.

Messaging

Only when your network operator supports this service, you can use the function.

Write Message

You can edit the SMS.

Inbox

The phone will prompt you when you receive a new message.

Drafts

In the Drafts, please select Options, and then you can do send form SIM1/SIM2, edit and some other operations.

Outbox

This function is used to check messages in outbox.

Sent messages

This function is used to check the messages sent from SIM1/SIM2.

Delete messages

This function is to delete the messages of Inbox, Drafts, Outbox, Sent messages or All messages at once.

MMS

Write Message: You can edit the MMS message. Inbox: The phone will prompt you when you receive a new MMS. Outbox: This function is used to check MMS in outbox. Drafts: This function is used to check messages in drafts. Templates: Your phone saves messages both for MMS in common use. You can view, write message, properties. MMS Settings: You can configure the default information about MMS properties.

Broadcast Message

This network service enables you to receive all kinds of text messages, such as weather reports or transportation information. Until now, there are several networks afford the service in this world. Please consult your network operator for more reference.

SIM1/SIM2 Broadcast message:

Receive Mode: Turn on or off the Cell Broadcast. Read Message: Scroll the Up/Down Key to select the message. Languages: Select the desired language to display the broadcast message. Note: Your network operator decides whether the language is supported or not. Channel Settings: You can choose Select, Add, Edit or Delete to receive the Broadcast information.

Templates

Your phone saves messages both for SMS in common use. You can edit, remove or write message.

Page 14

SMS Settings

You can configure the default information about SMS properties. Before using message function, you need to do necessary settings as follows:

1. Profile settings: User should set a proper profile for mobile message. Enter into

each mode to find the profile name, message centre number, validate time, sending profile setting.

2. Voicemail server:

Edit: Input or modify the number and the name of voice mailbox. Connect to Voice: You can hear messages in the voice mailbox. Note: This service is supplied by the network, such as the message machine service. It enables the caller to leave messages when you can't or you are unwilling to answer the coming call. Your number for the voice mailbox is saved in this phone. In standby mode, hold the number key 1 to dial the number of the voice mailbox after the number is configured. Please consult your network operator for more details.

3. Common settings: Activate Delivery Reports, Reply Path and Save sent message.

4. Memory status: User can check the available space in SIM card or mobile

message box.

5. Preferred storage: User can choose location to save the message either in mobile

or SIM card.

Call Center Call History SIM1/SIM2 Call history Missed Calls: Displays the list of recent missed phone numbers; Dialed Calls: Displays the list of recent dialed phone numbers; Received Calls: Displays the list of recent received phone numbers. Delete Call Logs: You can delete all records of missed calls, dialed calls or received

calls with this function or Delete all folders drastically.

Call Timers:

 Last Call: The last call time can be checked.  Dialed calls: The total time for all dialed calls can be checked.  Received calls: The total time for all received calls can be checked.  Reset All: Reset the counters.

Call Cost:

Last Call Cost: You can check the last call’s charges. Total Cost: You can check the whole call’s charges. Reset Cost: You can modify the call’s charges, and reset the cost to 0. PIN2 code is required while modifying. Max Cost: You can check and modify the upper limit. PIN2 code is required while modifying. Price per Unit: You can check and modify the call’s rate. PIN2 code is required while modifying. Note: This function is related with the SIM card. Some SIM cards don’t support the function. PIN2 is provided from the network operator. Please consult your network operator to obtain the number.

Text msg. Counter:

Sent: You can check and clear the number of sent messages. Received: You can check and clear the number of received messages. Note: This function has nothing to do with the SIM card. The amount of sent or

Page 15

received messages will not change even if you change the SIM card.

GPRS Counter:

- Last Sent: User can get the record of the bytes sent last time.

- Last received: User can get the record of the bytes received last time.

- All Sent Data: User can get the record of all the bytes sent.

- All Received Data: User can get the record of all the bytes received.

- Reset Counters: User can reset all counting.

In any country using digital GSM network, so long as you are in network covering range, you can know it by examining the indication bar of the network signal intensity at upper left corner of the screen.

Call Settings SIM1/SIM2 Call settings

1. Caller ID (Net work Service): You can select Set By Network, Hide ID or Send ID.

The default state is the Set By Network.

2. Call Waiting > Activate, the network will notify you of a new incoming call while you

have a call in progress (Net work Service).

3. Call Divert: This network service allows you to divert your incoming calls to anther

number. For details, contact your service provider.

4. Call Barring > Activate, this network service allows you to restrict incoming calls from

your phone. For details, contact your service provider.

5. Line Switching: Switch to Line 1 or 2, the default one is Line 1.

Note: If Line 2 is selected, making calls from Line 2 depends on the network operator.

6. Close User Group (Only for SIM1): if On, this network service specifies the group of

people whom you can call and who can call you. For further information, contact your network operator or service provider.

Tip: only SIM1 card support this option. Advance settings

1. Auto Call Record: When set the status On, the phone will record each and every

calls and save it in the phone or memory card.

2. Blacklist: you can set 20 numbers. When this Black list is enabled, you won’t receive

the calls from the numbers entered in the Blacklist.

3. Auto Redial: On, the phone will automatically redial the last called number after a

while if you fail to connect to the number. The times for auto redial are up to 10 times. Press Abort to end Auto Redial.

4. Background Sound: This function is to activate different background sound like

Motor cycle, Sidewalk, MRT1, MRT2, Restaurant, Pub, Chord, Alarm, Dou, White noise etc.

5. Call time Display: On the call, time will display when status On.

6. Call Time Reminder: This function prompts you to end the call in time to save the call

cost. You can select Off, Single, or Periodic.

7. Auto quick end: You can set ON/ OFF, and set a time (1~9999s) as your desire.

8. Reject by SMS: This function when enabled is used to send the reject message

during an incoming call.

Organizer

Offer you several little tools to let you feel more comfortably.

Page 16

Bluetooth

You can use Bluetooth transmission of documents directly. Search equipment to the transfer, In accordance with the onscreen instructions can operate, and accepts data, choose to receive the same, document will be automatically stored in the directory.

Power: Bluetooth Switched on or off. Visibility: Fix it On make your phone discoverable for others. My device: Can inquiry new device. Search audio device: You can search audio device. My Device Name: The default name is “LEMON Duo339 super”. Advanced: Audio Path: This function is to keep the audio path to phone or BT headset when

connected Bluetooth headset. Storage: This function to set the storage location for the file received via Bluetooth sharing.

Sharing permission: It should be Fully control by default. My address: One can found the BT address of the phone at this option.

Calendar

This includes English, Hindi and Hijri Calendar. You can View today, View all, Add event, Jump to date.

Tasks

You can View, Add, Edit, Delete, Delete overdue, Delete All, Jump to date, Send vCalendar and Save as file as desired. Start up the Task and press OK. Press Options to access to the next step to add a new memo.

Alarm

The mobile phone provides several alarms and you can set them as your need. If you have configured an alarm, an icon indicated that you have configured the alarm will appear. No icon will show if you don’t set an alarm. Select “Edit” to set the alarm.

World Clock

Scroll to browse every city’s time zones in the world map. The related date and time will display at the bottom of the screen.

Calculator

The calculator can add, subtract, multiply and divide.

Unit Converter

You can make the units conversion for weight and length. Enter the number into the column, and then press “OK” to get the result.

Currency Converter

You can make currency conversions. Press OK after enter the exchange rate, and then enter the number of the currency, and press OK to get the result.

Health

Provides the reference of BMI and Menstrual.

Page 17

Ebook reader

You can read E-book with “*.TXT” format which saved in your memory card.

Multimedia Camera

During the view-findings mode, press the left soft key, to carry out the following operations:

Photos: To display the file list. Camera Settings: To set some relative spec of the camera. Image Settings: This includes photo size and photo quality adjustment. White balance: To set the balance of light. Scene Mode: To set the scene mode auto or night. Effect settings: To set special shot effect. Storage: To set the default storage path. Restore Default: Can restore default. Image viewer

Enter the “image viewer” to view the image files in the default folder “Photos”.

Video recorder

Your phone supports the video recorder function. Press your navigation keys left and right to adjust the EV, and press it up and down to adjust the zoom. Press the center navigation key to get start and pause. Press the RSK to stop the video recording and LSK to go to Options to perform the following operations:

Camcorder Settings: To set some spec. of the video recorder. Video settings: You can set the video quality, size limit and so on. White balance: To set the balance of light. Effect settings: To set special shot effect. Storage: You can store the Video in the phone or Memory card. Restore Default: Press the left soft key and select Yes to return to default settings.

Video Player

You can perform the following operations:

Play: You can play the specified video. Send: You can forward the video as multimedia message, Email and via Bluetooth. Use as: This option is used to set the video as caller ID function. Rename: You can rename the specified video. Delete: You can delete the specified video. Delete All Files: You can delete all videos. Sort by: You can sort your videos by Name, Type, Time and so on. Storage: To set the default storage path.

Audio Player

The Play, Stop, Back, Forward functions correspond to the Up, Down, Left and Right key respectively. Select List to access the Play List, and then select Options to perform the following functions:

Note: The current system does not support some MP3 with a non-standard format.

1. Play: to play the specified music.

2. Details: Title，artist, Size, Time, and so on.

3. Add to Ringtones: You can use MP3 music as the ring tone for incoming calls.

Page 18

4. Refresh List: You can refresh the music file list of the memory card.

5. Settings:

- Pre. Play list: You can choose the Mp3 files in the Phone or in the memory card.

- List Auto Gen.: On/Off, play the music saved in system/select music files from the File Manager to play.

- Repeat: You can select Off, One or All.

- Shuffle: You can select On/Off.

- Background Play: On, the music will continue to play even if you exit the Playing

Screen (music will stop when a call is coming).

Bluetooth settings

There are two sub options here.

- BT stereo output > you can select On/Off.

- BT stereo headset > Insert the earphone and access the Headset mode

automatically. Audio effect: User can change the equalizer effects to different modes while playing audio player in headset mode.

Note: Press the volume keys (* and #) to adjust the volume. Make sure that the volume is appropriate for your hearing while using the audio player. To enjoy non-stop music, please download music to the “My Music” folder of phone’s internal memory recognized as a USB disk on your PC. The Audio Player of the phone will automatically play music files from the “My Music” folder. You may need to refresh it manually from the settings in case you have earlier selected manual refresh settings.

Sound Recorder

The mobile phone supports 2 recording formats: WAV and AMR. You can record conversations, which may be saved to the Audio folder under Phone/ File Manager. If there is a record, press the left soft key you can select: Record, Play, Append (only for AMR), Rename, Delete, Delete All, Setting, Use, and so on.

FM Radio

You can use your phone to listen to FM radio stations once the original Handset is plugged into the connector or antenna is opened.

1. Press the Down key to Power on/ off the FM radio.

2. Press the OK key to record the FM.

3. Press the Left/Right key to change the searching function of step to next frequency.

4. Press the */ # key to adjust radio volume.

5. Press Options to access the following options: channel list, manual input, Auto search, Settings, Record, Append, File list.

Schedule FM Record

With this function, your phone can record the FM program as the schedules once the original Headset is plugged into the accessories connector. You can set Off or On, the date and time, repeat style, channel settings and record settings.

Fun & Games

There are several interesting game and java application in the phone. Please refer to instructions from the menu for more details. Tip: The game menu includes Start Game, Game Level, Best Grades and Game Help.

Page 19

Opera Mini

Opera Mini is a web browser designed primarily for mobile phones to open big memory size websites. Memory size websites. You can experience better, faster, efficient and economic way of Web browsing.

Lemon Twist:

Lemon Twist includes various features like Atom(m-Commerce), Facebook, Twitter, Buzzintown, Nimbuzz messenger, MSN messenger, Yahoo Front Page, Yahoo mail.

Note: GPRS should be activated from the operator side and also in the SIM Card.

This E-mail function can receive and send emails supported only Outlook Email server. Please read the following related information carefully before you use the function: Email: Please log on some Internet web to apply an email account. That email account is just the "Email" referred in your manual. It belongs to the email server computer system provided from the network operator. Emails you received and sent are transferred by that email server. Email Server: is a computer that supplies the email service from the network operator. Please consult your network operator to obtain the server name. POP3 and IMAP are common use servers in our life:

1. POP3: is a client/server protocol in which e-mail is received and held for you by

your Internet server. Once you connect the web and enable the email, your phone will automatically download the new email from POP3 email server to the phone's inbox, and then delete those emails from the server. If you want to save those emails, please select the "Leave a copy of messages on server" option in "Email Setting".

2. IMAP: (Internet Message Access Protocol) is a standard protocol for accessing

e-mail from your local server. IMAP provides the user more capabilities for retaining e-mail on the server and for organizing it in folders on the server. IMAP can be thought of as a remote file server.

Note: Please consult your network operator to ensure which type your email is.

User Name: The name you enter when you applied the email account. When you log

on the email, the server should verify your identity. Password: The code you enter when you applied the email account. The email server will verify whether you are the only user for the email account or not according to the user name and password you input. Email Address: This is the address used in Internet. According to the address, people send emails to your mailbox. The address is assigned by the system when you apply the email, so you can’t modify the address.

Send and Receive

You can read sent and received emails.

Write Email

 To: edit the receiver E-mail address.  CC: edit others E-mail address which used to send the E-mail to others at the

same time.

 BCC: edit others E-mail address which used to send the E-mail to others secretly

at the same time.

Page 20

 Subject: edit the Subject of the E-mail.  Attachment: attach 3 files saved in the phone. The default mail size is up to 90K.  Priority: you can select Normal, Low or High.  Content: enter the text and press “Ctrl” Key to switch input methods.

When you select Done, you can do the following operations:

− Send: to send the email.

− Send and Save: to save the email to Sent and send it out.

− Save to Drafts: to save the email to Drafts without sending it out

− Quit without Saving: to exit the Email Option without saving the email.

Inbox

All received emails display in the inbox, and the icon

means the email is unread. Use the Down/ Up key to scroll the cursor to check the list, and the subject and time will display. If the email has been read, the icon will change to the read icon. Please press the left soft key to access Option, and follow steps described as below:

 Reply: to reply the sender.  Reply to all: to reply all senders.  Forward: to forward this email to others.  Delete: to delete this email.

Outbox

In the Outbox, Select Options, and then you can View or select other operations.

Sent

After the email is sent out successfully, you will be asked to save the email into the Sent or not. Please refer to the Unsent for more details.

Drafts

Emails in Inbox, Sent or Unsent and the email unfinished can all be saved into the Drafts. Please select Option, and then you can Edit, Mark as Deleted or Delete.

Clear mailbox

Use the function to delete emails in Inbox, Sent, Outbox or Drafts respectively.

Delete marked Emails

Use the function to delete e-mails with the deleted mark in Inbox, Outbox, Sent, Drafts respectively, or Delete all mailboxes drastically.

E-mail Accounts

Please select one mode from them. After you edited the mode, please activate it to use the E-mail function. 1> E-Mail Address: user define 2> Display Name: user define 3> Username: user define 4> Password: user define 5> Outgoing Server: user define 6> Incoming Server: user define 7> Advanced Settings:  Account Setting:

1> Account Name: user define 2> Data Account: user define 3> Protocol: POP3 4> Check Interval: user define 5> Download Size: user define( 102400, max)

Page 21

6> Retrieve amount: user define( 50, max) 7> Reply to address: user define

 Outgoing Server:

a) Outgoing Port: 25 b) Authentication: user define

 Incoming Server:

1> Incoming port: 110 2> Download Options: user define 3> Copy on Server: user define 4> Del. server mail: user define

 Signature: You can set Auto Signature, Signature Image and Signature Text.

Tip: the word “user define” may indicate what you enter or select should consider the local network condition, please consult your network operator and the local dealer for more information.

Templates

You mobile phone saves many template in common use. What you can do for those are Edit, Remove and Write Email.

Settings

User Profiles General

1. Activate

2. Customize

 Tone Settings: Includes SIM1/SIM2 Incoming Call, Alarm, Power on, Power off,

SIM1/SIM2 Message, and Keypad.

 Volu me : Includes the volume setting of Ring Tone and Key Tone. The volume

degree is from 1 to 7.

 Alert Type:

− Ring Only: Just ringing.

− Vib. Only: Just vibration, no ringing.’

− Vib. And ring: Vibration and Ringer at same time.

− Vib. then ring: Ringing after vibration.

 Ring Type:

− Single: Rings once when a call is coming.

− Repeat: Rings continuously when a call is coming.

− Ascending: Rings continuously and the volume increases gradually.

 Extra Tone:

− Warning: If necessary, you will be warned by the prompt tone.

− Error: You will be warned by a tone if you make a mistake.

− Camp On: A prompt tone will be heard after searching the network successfully.

− Connect: A prompt tone will be heard after getting through to the dialed number.

 Answer Mode:

− Any Key: Press any key to answer a call (Except of Hang Up Key and Right Soft

Key)

Page 22

Meeting

Please refer to “General” for more details.

Outdoor

Please refer to “General” for more details.

Indoor

Please refer to “General” for more details.

Headset

Insert the earphone and access the Headset mode automatically. This mode has no Activate options. Please refer to “General” for more details. Note: Press and hold the # key to enable or cancel the silent mode. In the Silent mode you can’t hear any sounds indicates a call or a SMS is coming.

Bluetooth

You will enter into Bluetooth mode after you activate the Bluetooth function. This mode has no Activate option; the detailed operation has been shown in the “General”.

Energy-Saving

This mode is only activated. The backlight goes dim when you activate this profile.

Dual SIM settings

You can choose one mode as your desire from the options:

1) Dual SIM open, 2) Only SIM1 open, 3) Only SIM2 open, 4) Flight mode.

Phone settings Time and Date:

 Set home city: Select the desired home city.  Set Time/Date: Enter the current time, date and Daylight saving.  Set Format: Select a time, a date format and Date separator.  Update with Time Zone: It can be set to On or Off.

Schedule Power On/Off: You can set the time for auto power on /off. Do turn the status on before using that function.

Note: Please disable the Schedule Power On function before you board an airplane. Language: Select the desired language for the display text. Pref. Input Methods: Select the desired input method for the default input method. Greeting Text: Set the status on, greetings will display when power on. Navigation Key: You can configure short cut functions for the Up, Down, Left and

Right key respectively. In the standby mode, press any one of them to access the appointed function.

Auto update of date and time: It can be set to On or Off. UART setup: When using this phone as GPRS Modem, select different UART port to

decide whether SIM1 or SIM2 to be used.

Display Settings

With this function you can configure the basic status of display characteristics including Wallpaper, Screen saver, Power on display, Power off display, Show date and time, Show owner number, Show Operator1 name, Show Operator2 name, Clock type and LCD backlight.

Network Settings

Please contact the network operator for the following network service.

Page 23

SIM1/SIM2 network settings

1. Network Selection New Search or Select Network can help search the network where you are in. You can select the selection mode: Automatic or Manual. When you select Automatic, the phone will make the preferential selection according to the network where the SIM card belongs. When you select Manual, you are required to select the same network as the registered network with the network operator by SIM card for your use.

2. Preferences Select the Preferred Networks. The default network is the network where the SIM card belongs. Select Options to perform the following operations:

 Add From List: Display all PLMN list.  New: Create a new network and set the network priority.  Change Priority: Reset the selected Network Priority.  Delete: Delete the current preferred network.

Security settings SIM1 security settings SIM1 Lock

It is asked to input the PIN. It can be configured if the PIN is correct. If SIM card is set on, it needs to input the PIN every time you power on. Three times wrong PIN input, it's asked to input PUK. PUK is used to release and modify the locked PIN. If PUK isn't provided or missed, please consult your network operator.

Change Password

You can change SIM1 PIN, SIM1 PIN2.

SIM2 security settings SIM2 Lock

Change Password

You can change SIM2 PIN, SIM2 PIN2.

Phone Lock

You can lock or unlock the phone. Enter the password to activate or deactivate the phone lock. When the phone is locked, you will be required to enter the phone password. 4-8 numbers can be used for the phone password. The default phone password is 0000.

Auto Keypad Lock

You can lock/unlock the phone keyboard and set the Key Lock Time to None, 5 sec, 30 sec, 1 min, 5min.

Change Password

You can change your phone password. The default password is “0000”.

Mobile tracker

This feature allows users to track their phone if they are lost or stolen. Switch on Mobile Tracker application and whenever a new SIM is inserted in your phone you will receive a SMS on pre defined numbers.

1) Open mobile tracker This function requires your network support. You can set ON or OFF. When the function ON and the phone change a SIM card, the phone will sent a message to the

Page 24

number which you set in Tracker Number. The message will tell you that which number is using your phone now. The default password is 0000.

2) Recepient number You can set upto 5 recepient numbers to which the tracker message would be received.

3) Change Password You can change Phone Tracker Password. The default password is “0000”.

Shortcuts: You can set shortcuts for those functions you often use.

Restore Factory Settings

Access Settings to select Restore Factory Settings, and input password then press OK. All settings can be restored to factory settings with this function. The default phone password is 0000.

Sound effets

This functions is used to change the equalizer effects (Normal, Bass, Dance, Classical, Treble, Party, Pop, Rock) during playing audio player.

Services STK Service

This service is offered as the SIM card service provided by the network operator.

Internet service

Internet service enables you tour around the Internet world easily and happily. Please follow the steps described as below:

1. Homepage: The default Internet Web Address.

2. Bookmarks: Save the Web address you often use.

3. Input Address: Press the left soft key to access Enter Address, and then input the

web address to go to the Internet.

4. Recent Pages: Records after you browse the Website.

5. Service Inbox: Messages sent to users from the Web site.

6. Settings: You can configure: Select SIM, Profiles, Browser Options, Preferences,

Security settings, Service Message Settings.

Data Account

Press the left soft key to perform following steps:

1. GPRS: Edit the GPRS account.

Note:

1) To open this function, you should apply GPRS service to your SIM card.

2) Some of the heavy sites could not be open as it will show the error “Insufficient memory”. Suggest to open only WAP enabled site.

3) Download from some of the websites could not be done.

File Manager

You can use the function to manage all types of files saved in the Memory card or Phone.

Page 25

APPENDIX Appendix A: Guidance on Entry Methods

This phone provides input methods, which can be used in editing the Phone Book, short messages, memos, greetings, alarms and other text applications.

The Icons of Input Methods

After entering different kinds of edit windows (including edit phonebook, short messages. etc.), the icons of input are as follows:

“e

ABC”: The Entry method of Smart ABC appears as: “e2 ABC”.

“e

abc”: The Entry method of Smart ABC appears as: “e2 abc” “ABC”: The entry method of Multitap ABC appears as: “ABC”. “abc”: The entry method of Multitap abc appears as: “abc” “HI”: The entry method of Multitap Hindi appears as: “HI” “123”: The Entry method of Numeric appears as: “123”

How to Switch Between the Input Methods

Press the # key to switch the input methods. e.g.: If the current input is Smart ABC the screen will show “abc”.

How to Input Special Symbols

If you want to input special symbols, such as " @ = < >”, Etc., please press the “*” key at the right bottom of your keypad.

Page 26

Appendix B: Troubleshooting

This section lists some problems that you might meet while using your phone. If you feel that your phone do not operate normally, please reset settings first, and then follow Troubleshooting Guide. If you are still unable to solve problems, please contact the authorized service center or the store from where you purchased the phone.

Problems Solutions

Can not answer or make a call

Make sure that the phone has been switched on. Make sure that the battery is charged. Make sure that the signal intensity is high enough. Make sure the own number function in the call setting is system preset or number sending. Make sure the line switch in call setting is the system preset line. Check whether you have set up call barring or fixed dialing or any other safety function. Check whether you have set up call diverts. Check whether you have inserted the proper SIM card correctly.

Low voice Check if the volume has been set too low.

No ring

Check whether you have set up the” Silent” option. Check whether the ring volume is not too low Move away from a noisy place to check if you can hear the phone ringing.

Check whether you have set up call diverts. T-Flash card

detect slowly

Format your T-Flash card with your phone.

Note: To protect your files from getting lost, please backup the

important information into the safe place before you formatting

card.

Appendix C: FCC Statement

This device has been tested and found to comply with Part 15 of the FCC rules. Performance is subject to the following conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

3. Changes or modifications not expressly approved by the manufacturer or authorized service center could void the user’s authority to operate this equipment.

Page 27