Bubble Master 2000
V.12.15.00
Please Read Carefully Before Operating
Table of Contents
Page 1 Technical Specifications
Page 2 Warning
Page 3 Operating Procedure
Page 4 BubbleMaster 2000 Control Features
Page 5 Shut Down Procedure
Page 5 Trouble Shooting the BubbleMaster 2000
Page 6 Maintenance
Page 6 Safety Precautions
Page 7 Warranty
Page 8 Accessories
Technical Specifications
Model: BubbleMaster 2000
Type: Water Base Bubble generating system
Size: 723 x 412 x 406 mm. High (Incl. Bubble Projector)
28 1/2x 16 x 16 1/4 High (Incl. Bubble Projector)
Weight: 21 Lbs. 9.51 Kg.
Power Rating: 115 Volt A.C. 50/60 Hz 1 Amps
220 Volt A.C. 50/60 Hz 0.5 Amps
BubbleMaster 2000 Illustration
1
Warning
WARNING
READ THESE IMPORTANT SAFETY INSTRUCTIONS
Do not remove the outer case until power has been
disconnected from the machine
WARNING
Ensure that this unit is grounded at all times.
Failure to do so may result in serious injury.
Never use alternative fluids. Toxicity free output
M.S.D.S. Available by request or at www.lemaitrefx.com
WARNING
is your responsibility.
2
Operating Procedure
Setup
Unpack the Bubble Master
2000 and inspect all components. Although the packaging was designed for the
rigours of todays parcel delivery sevices, damage may have
occurred during shipping.
1.) Prior to operation, the
extension sleeve may be
placed over the bubble outlet.
This will allow the bubbles to
be projected higher, before
they begin to disperse outwards.
For lower flying bubbles do not use the extension sleeve.
2.) Place the Bubble Master 2000 on a level sturdy surface, or use the optional adjustable
stand sold separately.
3.) Open a container of Le Maitre BubbleMaster 2000 Bubble Fluid, and pierce the foil top.
Pour the fluid into the bubble outlet. Fill up to 1/2 below the resevoir top. This initially
should take approximately 1 gallon.
4.) Plug the BubbleMaster 2000 into an outlet that is capable of sustaining the current
load listed on the product serial plate.
3
BubbleMaster 2000 Controls
1. Power up unit by connecting to suitable power supply
2. Upon power up the display will read" LE MAITRE FX BUBBLE 2000" for 2-5 seconds .
3. The Main Menu will be displayed. The Main Menu will indicate System Status (ON or
OFF), Fan Status (ON or OFF), and the current Speed Setting (0 to 99).
4. Pressing the START/STOP/ENTER keypad at the Main Menu will change the setting to
System Status ON or OFF.
5. To select the Fan Speed Menu, Bubble On Menu, Bubble Off Menu, or Main Menu
press the Previous Menu or Next Menu keypads until the appropriate menu is displayed.
6. To change the value of the Fan Speed, Bubble On Time, or Bubble Off Time settings
use the 'Increase or 'decrease' keypads, the new setting will be saved by pressing the
START/STOP/ENTER keypad.
4
Shut Down Procedure
1.) Disconnect the BubbleMaster 2000 from the power source.
2.)Remove the bubble extension sleeve if used..
3.) Using a funnel, empty the contents of the fluid reservoir back into the
1 gallon fluid container. This can be done by tipping the unit, and pouring the fluid out of the bubble outlet.
4.) Replace cap on the fluid container to keep dirt and debris from
entering.
5.) Rinse out fluid reservoir and bubble wheels with hot tap water tap
water to remove excess Bubble fluid residue. Using a paper towel wipe
out extension sleeve and bubble oulet.
Empty into sink or appropriate drain.
Troubleshooting BubbleMaster 2000
Bubble Wheel not turning:
Ensure that set screws are secure in bubble wheel motor shaft.
Intermittent bubbles produced.
Ensure that there is enough fluid in the fluid reservoir, and that the bubble wheels are
being submersed in bubble fluid.
5
Maintenance
Fluid Reservoir
When storing the Bubble Master 2000 for any extended period, be sure to thoroughly
rinse the fluid reservoir.
Bubble Wheels
When storing the Bubble Master 2000 for any extended period, be sure to thoroughly
rinse bubble wheels.
Safety Precautions
1. Ensure that operation of the machine is supervised by suitably trained and authorised
personnel.
2. Do not modify the machine or use a machine which has been damaged in any way.
3. Allow sufficient air circulation around the machine at all times.
4. Protect the BubbleMaster 2000 from direct weather effects and wet locations.
5. Use only Le Maitre Special Effects Bubble Master 2000 bubble fluid.
6. Avoid direct bubble output continuously at persons, structure or objects within close
proximity of the discharge nozzle.
7.) Do not allow any liquid to spill into or on the remote control or the cover behind the
remote.
6
Warranty
Warranty:
All warranty is one year parts and labour unless specified and is on
manufacturer defect only. Overuse or poor maintenance is not
accepted. Le Maitre fluids must always be used. Accept no substi
tutions as there are no exceptions to this rule. Proof of purchase or
proof of sale must always accompany any warranty returns. An
RA (return authorization) number must be noted on the outside of
any box returned to our facilities. Any packages without a clearly
marked RA number will not be accepted by our receiving depart
ment. Freight on warranty items are freight prepaid to our facility
and we will prepay freight back to your facility after repair, by the
most economical means available. Should you require the item
express-returned, then you are responsible for any difference in
freight cost.
Return Policy:
Return of any product must be done within 30 days of purchase.
The package must be returned freight prepaid and the RA number
clearly marked on the outside of the box. A restocking charge of
up to 25% may be levied. Only credits are issued to the dealers
account. Any product not returned within 30 days is considered
purchased.
Warning:
Le Maitre Special Effects Inc. considers all it's product to be safe
for use in the application it was intended. Le Maitre Special
Effects takes no responsibility for misuse or incorrect use. Always
refer to equipment owners manual for proper use.
7
Accessories
g ng
g ng
gnging
g
gnging
Model De scription
CLF 2944 DMX Interface
CLB 2005 Bubble Stand Mountin
CLB 2007 Bubble Machine Stand
CLB 2004 Bubble Wall Mountin
CALL Bubble Machine Han
CLB 2004 Bubble Securin
CLB 2006 Bubble FDS Option
CLF 3100 20 L. Pail Han
CPH PC001 5 Pin DMX/Bubble Remote Cable 25'
CPH PC005 5 Pin DMX/Bubble Remote Cable50'
CPH PC007 5 Pin DMX/Bubble Remote Cable100'
Bng Bracket
Plate
Plate
Bng Bracket
Bng Bracket
Use only Le Maitre Special Effects Bubble Master 2000 Bubble Fluid. This biodegradable
fluid has been formulated to deliver long lasting dryer bubbles that almost dry on contact.
Recommended Fluid
8
Notes
9
Loading...