Lelux Electronics LELUX218WR Users Manual
OWNER'S MANUAL
INSTALLATION
1. Remove the screw from the battery compartment cover.
2. Install 2 “CR2032” batteries (included) on the battery box,
ensure the polarity is correct.
3. Replace the battery cover and screw.
4. Mount the magnetic door/window sensor
Choose a suitable location, stick the main unit to the
door/window frames by attached double – side tape. Then stick
the magnetic unit (smaller unit) to the door/window by attached
double-side tape and make sure to align the “ ”mark to right
“ ”mark on the main unit and “▲” facing “▲” at no more than1/4”
apart as shown in (fig.1a/b)
5.External Magnetic sensor terminal
You can additional wire magnetic sensor to expanding you
desired detection area.
a.remove the screw from the battery compartment cover
b.remove the screw from terminal and take out connect wire
(fig.2)
c.Measure the length of wire needed to connect the sensor to the
transmitter, then cut the wire to the correct length. Strip about
1/2 inch of insulation from the wire ends, and twist the wires
together
d.Connect the sensor switch on door to the main terminal post
using the wire you just cut. (There is no polarity need to be
taken care of, any terminal will be fine, as long as the wires from
a loop)
e.Connect another sensor switch screw to another switch
terminal post by using the parallel another wire as shown in
(Fig.3)
f.If you connect more than one sensor to the main unit, connect
them in series as shown in (Fig.4)
NOTE: After select a location, you should test the sensor transmitting range before mount it permanently, turn the CHIME switch to
ON of T015, T016 main unit or press HOME button of T018 main
unit, then open/close the magnetic switch of door/window sensor
to trigger, you will hear the main unit sounds “DING DONG” chime
if signal is received successfully, if not, elongate mini retractable
antenna or change location is required.
LEARNING CODE TO MAIN UNIT
The door/window sensor compatible T015, T016, T018 main
unit, must learn code to main unit then use, learn code operation
see main unit manual.
OPERATION
After 60 seconds installed battery, the unit will into standby
mode. Once the door/window opened or the unit vibration will
output wireless radio signal and LED flash。
BATTERY LOW INDICATOR
When battery goes low, the LED will light on 3 seconds and off
1 second, change a new alkaline 9V battery immediately, or the
sensor might not detection properly.
WIRELESS SLIM
DOOR/WINDOW SENSOR
Warning:
Changes or modifications to this unit not expressly approved
by the party responsible for compliance will void the user's authority to operate the equipment. Any change to the equipment will
void FCC grant.
This equipment has been tested and found to comply with the
limits for a Class C digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for
help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation
(fig.1a) (fig.1b)
(fig.3)
(fig.2)
(fig.4)
- 1 - - 2 - - 3 -
Loading...