Leister Welding-Pen A, Welding-Pen S Operating Instructions Manual
The LEISTER Welding-Pen A and S are hot air tools that can be installed for continuous
operation. They have an ergonomic shape and are light weight what makes them
suita
ble as hand tools as well as for the installation into machines and vent constructions.
The cooled heater tube as well as the LEISTER screw-on drawing nozzle with
taking tip make the Welding Pen to a very efficient tool for plastic welding.
• Welding of thermoplastic materials and also single-ply flexible plastics in the
form of boards, tubes, profiles, foams, tiles and sheets.
•
The following procedures are possible:
Rod and melt welding by means of LEISTER nozzles
• The hot air tools Welding Pen A and S need an external air-supply
(LEISTER blower or compressed air).
LEISTER Welding-Pen A
LEISTER Welding-Pen S
Hot air tools
Please read operating instructions carefully
before use and keep for further reference.
GB
OPERATING INSTRUCTIONS
1
APPLICATION
®
LEISTER Process Technologies, Riedstrasse, CH-6060 Sarnen /Switzerland
Tel. +41 41 662 74 74 Fax +41 41 662 74 16
www.leister.com sales@leister.com
LEISTER Welding-Pen A
• Heating element protected
against overheating
• Adaptor tube with heat protection
• Temperature steplessly adjustable
by regulation of air flow
LEISTER Welding-Pen S
• Heating element protected
against overheating
•
Adaptor tube with heat protection
• Temperature steplessly adjustable
with potentiometer
Electrical safety: double insulated
2
TEST SIGNS
TECHNICAL DATA
Danger to life when opening the tool, as live components
and connections ar exposed. Unplug the tool before
opening it.
Incorrect use of hot air blowers can cause fire and
explosion hazard, especially near combustible materials
and explosive gases.
The tool must be operated with supervision. Warmth can
reach combustible materials, which are out of sight.
For personal protection on building sites we strongly
recommend the tool be connected to a GFCI (Ground
Fault Circuit Interrupter) or a RCCB (Residual Current
Cir
cuit Breaker) .
The voltage rating stated on the tool must correspond to
the line/mains voltage.
Do not touch the element housing and nozzle when they
are hot as they can cause burns. Let the tool cool down.
Do not point hot air flow in the direction of people or
animals.
Protect tool from damp and wet.
FI
120
230
WARNING
CAUTION
Welding-Pen A Welding-Pen S
Voltage V~
120 230 100 120 230
Frequency Hz 50/60 50/60 50/60 50/60 50/60
Capacity W 600 1000 450 600 1000
Temperature °C 20 – 600 20 – 600 20 – 600 20 – 600 20 – 600
Air flow l/min. >70 >120 >40 >50 >60
Air pressure Pa max. 10
5
(dynamic)
Weight g 1000 with 3m cable, air hose and Y-connection
Size mm ø 32/43 × 270
Mains voltage cannot be switched over
This tool is CCA certificated (CENELEC Certification Agreement).
Description of tool
1. Heat protection tube
2. Potentiometer for temperature
adjustment
3. Handle
4. Hose clamp
5. Air hose
6. Y-connection
7. Hose connection for
air-supply G1/4”
8. Cable screw fitting for mains
supply M16 × 1.5
9. Power-supply cord
10. Cover
11. Screwed nozzle joint
1
2
3
4 5
1
11
11
5
4
6
8
9
7
10
3
4 5
3
USAGE Welding-Pen
Welding-Pen S
Welding-Pen A
Loading...