Page 1
Leica Lino ML90, ML180
Page 2
DE
EN
FR
IT
ES
PT
NL
DA
SV
NO
FI
JA
ZH
KO
PL
HR
HU
RU
CZ
EL
LT
LV
EE
SL
SK
TR
BG
RO
User Manual
Version 785880b
English
Congratulations on your purchase of the Leica Lino
ML Series.
section "Safety instructions".
Before starting up the instrument
for the first time, please read
through the entire User Manual
paying special attention to the
Contents
Start up..................................................................1
Interface ................................................................4
Operation .............................................................. 5
Working with receivers ...........................................9
Checking the accuracy .......................................... 16
Technical data ...................................................... 19
Care and transport ............................................... 21
Safety instructions ............................................... 23
Warranty .............................................................. 27
Leica Lino ML series 785880c en
Start up
Inserting / replacing batteries
1 Lino ML90/180: Turn the release screw on the
battery compartment a 1/4 turn (clock wise) with
the help of a coin or a flat head screw driver to
unlock the battery compartment.
2 Open the battery compartment cover and insert
the batteries, observing the correct polarity.
RVL100:Lino ML90/180:
XCR Catch:
1
Start up
Page 3
DE
EN
FR
IT
ES
PT
NL
DA
SV
NO
FI
JA
ZH
KO
PL
HR
HU
RU
CZ
EL
LT
LV
EE
SL
SK
TR
BG
RO
3 Insert the battery compartment cover on the
bottom side first and then insert the compartment completely until it is fully closed.
4 Then lock the compartment by turning the release
screw a 1/4 turn (counter clock wise).
The battery symbol 6 lights up when the
battery voltage is too low. Replace the batteries as
soon as possible.
• Insert the batteries observing the correct polarity
• Use alkaline batteries or rechargeable batteries
only.
• Remove the batteries if the instrument is not to
be used for a long period of time (to prevent
corrosion).
Start up
Charging the rechargeable battery pack / first-time use
• In case that your Lino ML is equipped with a
rechargeable battery pack you can recharge the
battery pack with the supplied Lino ML charger
(Art Nr. 784967) by connecting the charger to the
jack on the battery door.
• The battery must be charged prior to first use
because it is delivered with as low an energy
content as possible.
• A full charging cycle takes 8 hours and the
charging will automaticly stop after a full cycle.
Each time the charger is connected to the unit a
charging cycle will be initiated. See also battery
status indications on the interface in section
"Interface" on page 4.
• The permissible temperature range for charging is
between 0°C and +40°C/+32°F and +104°F. For
optimal charging we recommend charging the
batteries at a low ambient temperature of +10°C
to +20°C/+50°F to +68°F if possible.
• It is normal for the battery to become warm
during charging.
2
Leica Lino ML series 785880c en
Page 4
DE
EN
FR
IT
ES
PT
NL
DA
SV
NO
FI
JA
ZH
KO
PL
HR
HU
RU
CZ
EL
LT
LV
EE
SL
SK
TR
BG
RO
4
1 LED off: not connected
2 LED lights continuously: charging for 8h
3 LED blinks: connected but not charging, online
operation possible
4 Jack for battery charger
WARNING:
Using a battery charger not recommended by
Leica Geosystems can destroy the batteries. This can
cause fire or explosions.
Precautions:
Only use chargers recommended by Leica
Geosystems to charge the batteries.
Leica Lino ML series 785880c en
1
2
3
8 h
3
Start up
Page 5
DE
EN
FR
IT
ES
PT
NL
DA
SV
NO
FI
JA
ZH
KO
PL
HR
HU
RU
CZ
EL
LT
LV
EE
SL
SK
TR
BG
RO
Interface
Keypad and control elements
1 LASER key
2 Horizontal MODE key
3 Vertical MODE key
Display
4 LED 1 system indicator:
• off: system off
• permanent green: system on
5 LED 2 level indication:
• off: levelled
• permanent red: out of level
6 LED 3 battery indication:
• off: battery full
• blinking: approx. 2 hours of use
• permanent red: unit switched off due to
battery too low
Special display notices:
Falling below or exceeding the permissible temperature range: The laser switches off and all LEDs flash.
Environmental conditions might lead to shut off of
the laser before the actual operation temperature
limits are reached.
Interface
Lino ML180:Lino ML90:
6
5
Lino
ML90
3
2
ON
LASER
1
4
4
Leica Lino ML series 785880c en
6
5
3
2
1
4
Lino
ML180
ON
LASER
Page 6
DE
EN
FR
IT
ES
PT
NL
DA
SV
NO
FI
JA
ZH
KO
PL
HR
HU
RU
CZ
EL
LT
LV
EE
SL
SK
TR
BG
RO
Operation
Switching on/off
• ON: Briefly press the LASER key 1.
• OFF: Briefly press the LASER key 1.
Laser functions
Pressing the MODE key 2 and 3 activates the
following laser functions:
Key
press
default laser A+B on laser A+B+C on laser D on
1x laser B on laser A+B on laser D off
2x
3x
the unit and will automaticly turn off after 180 sec.
To switch the plumb beam back on short press any
mode key 2 and 3 (see page 4).
ML90
vertical
(key 3)(key 3)(key 2)
all vertical
lasers off
repeat
default
The plumb beam will be on upon start up of
ML180
vertical
all vertical
lasers off
repeat
default
Leica Lino ML series 785880c en
horizontal
repeat
default
A
B
C
D
5
Operation
Page 7
DE
EN
FR
IT
ES
PT
NL
DA
SV
NO
FI
JA
ZH
KO
PL
HR
HU
RU
CZ
EL
LT
LV
EE
SL
SK
TR
BG
RO
Self-levelling and Lock functions
The instrument automatically levels itself within the
specified leveling range (Refer to section "Technical
data" on page 19) .
Leveling process is indicated by the LEDs. See Interface desciption on page 4.
Using the Laser with a receiver
To be able to detect the laser lines over long
distances (> 15 m) or in unfavourable lighting conditions, a laser receiver can be used. Laser lines can be
detected by a receiver that is able to detect pulsed
laser lines. The lines of the Lino ML are permanently
pulsed and are compatible with the range of recommended Leica laser receivers.
See section "Working with receivers" on
page 9.
Operation
6
Leica Lino ML series 785880c en
Page 8
DE
EN
FR
IT
ES
PT
NL
DA
SV
NO
FI
JA
ZH
KO
PL
HR
HU
RU
CZ
EL
LT
LV
EE
SL
SK
TR
BG
RO
Applications
Leica Lino ML series 785880c en
A
BE
C
7
Operation
D
F
Page 9
DE
EN
FR
IT
ES
PT
NL
DA
SV
NO
FI
JA
ZH
KO
PL
HR
HU
RU
CZ
EL
LT
LV
EE
SL
SK
TR
BG
RO
Manual fine adjustment of vertical lines
The Lino ML90 and ML180 lasers feature the possibility to manually turn the unit 360° around its center
axis and the possibility to fine adjust the unit by ± 4°
turning around the plumb axis. On the ML180 the fine
adjustment can be set to its 0° position by pressing
both mode keys 2 and 3 (see page 4) at the same
time for more than 2 seconds.
By turning the adjustment knob the laser beams can
be aligned manually.
Additionally to the manual fine adjustment
possibility described above, the Lino ML180 has the
possibility to automatically align itself to the position
of the Leica XCR Catch remote/receiver. For a detailed
description of all functions, please, refer to the
section "Working with receivers" from page 9.
Operation
360°
4°
4°
4° 4°
8
Leica Lino ML series 785880c en
Page 10
DE
EN
FR
IT
ES
PT
NL
DA
SV
NO
FI
JA
ZH
KO
PL
HR
HU
RU
CZ
EL
LT
LV
EE
SL
SK
TR
BG
RO
Working with receivers
Leica RVL100
The Leica RVL100 is a robust and easy to use laser
receiver and can be used with all Leica Lino line lasers.
Keypad
1
2
3
RVL100
1 ON/OFF key: switch the receiver on/off
2 Beeper key: change the sound level of the beeper
3 Sensitivity key: switch sensitivity (±1mm/±3mm)
Leica Lino ML series 785880c en
Display status symbols
1
2
3
4
1 Sensitivity : fine ±1 mm (default)
2 Sensitivity : coarse ±3 mm
3 Battery status: full
4 Battery status: low
5 Beep medium
6 Beep high
7 Beep off
8 Move receiver down
9 Move receiver up
9
RVL100
Working with receivers
8
5
6
7
9
Page 11
DE
EN
FR
IT
ES
PT
NL
DA
SV
NO
FI
JA
ZH
KO
PL
HR
HU
RU
CZ
EL
LT
LV
EE
SL
SK
TR
BG
RO
Leica XCR Catch
The Leica XCR Catch is a combined laser receiver and remote control for the Leica Lino ML180.
Keypad
1
2
1 ON/OFF key
2 Beeper key
3 Sensitivity key
4 Auto alignment key - Press 2 sec
5 Direction key down
6 Direction key up
3
4
XCR Cat ch
5
6
Working with receivers
10
Leica Lino ML series 785880c en
Page 12
DE
EN
FR
IT
ES
PT
NL
DA
SV
NO
FI
JA
ZH
KO
PL
HR
HU
RU
CZ
EL
LT
LV
EE
SL
SK
TR
BG
RO
Display status symbols
1
2
3
4
5
Leica Lino ML series 785880c en
XCR Catc h
6
7
8
9
AT
AK
AL AM
1 Sensitivity: fine ±1 mm
2 Sensitivity: medium ±3 mm (default)
3 Sensitivity: coarse ±5 mm
4 Remote arrows and direction keys
5 Alignment activated
6 Battery: empty
7 Battery status: medium
8 Battery status: full
9 Beep high
AT Beep low
AK Beep off
AL Move receiver down
AM Move receiver up
11
Working with receivers
Page 13
DE
EN
FR
IT
ES
PT
NL
DA
SV
NO
FI
JA
ZH
KO
PL
HR
HU
RU
CZ
EL
LT
LV
EE
SL
SK
TR
BG
RO
Pairing the Leica XCR Catch with the Leica ML180 Laser
The Leica XCR Catch remote/receiver works exclusively with the Leica Lino ML180 line laser. The
receiver that is included in the package is already
paired with the laser and only communicates with this
specific laser. If you want to pair another Leica XCR
Catch with your laser you will need to redo the pairing
procedure as described below.
When setting up the Leica Lino ML180 for
radio pairing make sure that no other Leica XCR Catch
is in operation in the area to avoid accidental pairing
with this remote.
Pairing procedure:
1Turn laser OFF 1.
2 Press and hold both buttons Horizontal MODE 2
and Vertical MODE 3.
3Turn laser ON 1.
4 Laser is in pairing mode (LED 4 5 6 blinking
slowly in sequence).
5Turn Receiver ON 7.
6 Press button Auto alignment 8 of receiver.
7 Pairing process is complete (LED 4 5 6 blinking
rapidly in sequence for 20 sec).
Working with receivers
Lino ML180: XCR Catch:
6
5
Lino
ML180
3
2
ON
LASER
1
4
If the laser is in pairing mode and does not
receive the signal from the remote, it will turn off
after 30 seconds.
The pairing procedure can be repeated
anytime. A Leica Lino ML180 laser and the paired
Leica XCR Catch remote will stay paired until they are
actively paired with another device.
12
7
8
XCR Catc h
Leica Lino ML series 785880c en
Page 14
DE
EN
FR
IT
ES
PT
NL
DA
SV
NO
FI
JA
ZH
KO
PL
HR
HU
RU
CZ
EL
LT
LV
EE
SL
SK
TR
BG
RO
Leica XCR Catch alignment features
Manual alignment
XCR Catch
± 4°
± 1.4m @ 20m
± 4.5ft @ 65ft
Lino
ML180
2
ON
LASER
1 1
Leica Lino ML series 785880c en
XCR Catc h
1 Set up the laser unit at the initial position.
2 Switch off the horizontal laserbeam with key 2.
3 Pre-align the laser (V line) within ± 4° of the
desired final alignment position.
4 Remotely align the laser with the direction
keys 1.
13
Working with receivers
Page 15
DE
EN
FR
IT
ES
PT
NL
DA
SV
NO
FI
JA
ZH
KO
PL
HR
HU
RU
CZ
EL
LT
LV
EE
SL
SK
TR
BG
RO
Automatic alignment (single mode)
In single alignment mode the Leica XCR Catch will
automatically align the Leica Lino ML180 laser once
and will then deactivate the alignment feature.
XCR Catch
1x ± 4°
± 1.4m @ 20m
± 4.5ft @ 65ft
1
2
3
XCR Catch
Working with receivers
Auto
4
3
1 Set up the laser unit at the initial position.
2 Pre-align the laser (V line) within ± 4° of the desired
final alignment position.
3 Select the sensitivity
Adjustment features for beeper and sensitivity are
deactivated during the automatic alignment
process.
Press auto alignment key 2 for 2 sec. until 2 red
4
LEDs blink.
during automatic alignment.
5 Predefine a scan direction by pressing the direction
keys
start looking for the receiver in a predefined
sequence (middle - left - right).
press the alignment key
button.
6 The auto alignment process will move the laser unit
until it is precisely aligned with the Leica XCR Catch
receiver.
7 When the receiver detects the exact position it will
sound a beep for 2 sec. and will display the lighted
green LED
alignment process will be terminated when middle
position has been found.
ment if no laser signal is found or the signal is permanently lost within a time frame of 45 sec. The receiver
will display all 5 LEDs blinking and will sound 3 short
beeps. To reinitiate the receiver press any key.
14
Horizontal laserline will be shut off
3
accordingly within the first 3 sec.
If no direction is predefined the unit will
To deactivate the auto alignment process
4
The receiver will deactivate the auto align-
1
to b e use d du ring alig nment .
2
or press the On/Off
and the middle position. The auto
Leica Lino ML series 785880c en
Page 16
DE
EN
FR
IT
ES
PT
NL
DA
SV
NO
FI
JA
ZH
KO
PL
HR
HU
RU
CZ
EL
LT
LV
EE
SL
SK
TR
BG
RO
Automatic alignment (continuous mode)
In continuous alignment mode the Leica XCR Catch
will automatically align the Leica Lino ML180 laser and
will then monitor and readjust the alignment continuously.
XCR Catch
± 4°
± 1.4m @ 20m
± 4.5ft @ 65ft
1
2
3
XCR Catch
Leica Lino ML series 785880c en
Auto
4
3
1 Repeat steps 1-3 from section "Automatic align-
ment (single mode)" on page 14.
2 Press auto alignment key 2 and sensitivity key 1
together for 2 sec. Horizontal laserline will be
shut off during automatic alignment.
3 Predefine a scan direction by pressing the direc-
tion keys 3 accordingly within the first 3 sec.
If no direction is predefined the unit will
start looking for the receiver in a predefined
sequence (middle - left - right).
To deactivate the auto alignment process
press the alignment key 2 again for 2 sec.
4 The auto alignment process will move the laser
unit until it is precisely aligned with the Leica XCR
Catch receiver.
5 When the receiver detects the exact position it
will beep for 2 sec. and will display the lighted
green LED 4 and the middle position.
6 The Leica XCR Catch makes the laser follow the
movements of the Leica XCR Catch and will
continuously keep monitoring and readjusting the
alignment after the middle position has been
found. To stop this continuous process press the
alignment key 2 or the On/Off button.
The receiver will automatically deactivate
the auto alignment in case no laser signal is found
or in case the signal is permanently lost after
more than 45 sec. The receiver will display all 5
LEDs blinking and will sound 3 short beeps. To
reinitiate the receiver press any key.
15
Working with receivers
Page 17
DE
EN
FR
IT
ES
PT
NL
DA
SV
NO
FI
JA
ZH
KO
PL
HR
HU
RU
CZ
EL
LT
LV
EE
SL
SK
TR
BG
RO
Checking the accuracy
Checking the accuracy of the Leica Lino ML90 and ML180 laser unit
Check the accuracy of your Leica Lino regu-
larly and particularly before important measuring
tasks.
Checking the accuracy of the levelling
Set the instrument on a tripod half-way between two
walls (A+B) that are approx. 5 m apart.
Allow the instrument to level. Direct the instrument
at wall A and switch on the instrument. Activate the
horizontal laser line and mark the position of the line
on wall A (-> A1). Rotate the instrument by 180° and
mark the horizontal laser line in exactly the same way
on wall B (-> B1).
Checking the accuracy
Then place the instrument at the same elevation as
close as possible to wall A and again mark the horizontal laser line on wall A (-> A2). Rotate the instrument by 180° again and mark the laser on wall B (->
B2). Measure the distances of the marked points A1A2 and B1-B2. Calculate the difference of the two
measurements. If the difference does not exceed 2
mm, then the Leica Lino is within tolerance.
| (A1 - A2) - (B1 - B2) | ≤ 2 mm
16
Leica Lino ML series 785880c en
Page 18
DE
EN
FR
IT
ES
PT
NL
DA
SV
NO
FI
JA
ZH
KO
PL
HR
HU
RU
CZ
EL
LT
LV
EE
SL
SK
TR
BG
RO
Checking the accuracy of the horizontal line
1.5 m
Set up the instrument on an even and flat surface.
Allow the instrument to level.
Position the instrument approx. 5 m away from the
wall. Direct the instrument at the wall and switch on
the horizontal and front vertical Laser line and mark
the intersection point of laser crosshairs on the wall.
Swivel the instrument to the right and then to the
left. Observe the vertical deviation of the horizontal
line from the marking. If the difference does not
exceed 3 mm, then the Leica Lino is within tolerance.
Leica Lino ML series 785880c en
Checking the accuracy of the vertical line
Set up the instrument on an even and flat surface or
on a stable tripod. Allow the instrument to level. As
reference, use a plumb-bob and attach it as close as
possible to an approx. 3 m high wall. Position the
instrument at a distance of approx. 1.5 m from the
wall at an elevation of approx. 1.5 m. Direct the
instrument at the wall and switch on the laser. Activate one of the vertical laser lines. Rotate the instrument and align it with the bottom of the plumb line.
Now read off the maximum deviation of the laser line
from the top of the plumb line. If the difference does
not exceed 2 mm, then the Leica Lino is within tolerance.
17
Checking the accuracy
Page 19
DE
EN
FR
IT
ES
PT
NL
DA
SV
NO
FI
JA
ZH
KO
PL
HR
HU
RU
CZ
EL
LT
LV
EE
SL
SK
TR
BG
RO
Checking the accuracy of the vertical plumbing
1
B1
A1
B2
1.5 m
max. 2 mm
2
1
B1
A1
B2
1.5 m
max. 2 mm
2
Set up the instrument on an even and flat surface.
Allow the instrument to level.
Checking the upper plumbing point:
Checking the lower plumbing point:
Set up the laser on its tripod or wall mount bracket
near point A1 at a minimum distance of 1.5 m from
point B1. The horizontal laser is aligned in direction 1.
Mark the laser dots A1 and B1 with a pin. Rotate the
instrument by 180° so that it points in the opposite
direction of direction 1. Adjust the instrument so that
Checking the accuracy
the laser beam hits point A1 exactly. If point B2 is no
further than 2 mm away from point B1, then the Leica
Lino is within tolerance.
Should your Leica Lino be outside of the spec-
ified tolerance, please contact an authorised dealership or Leica Geosystems.
18
Leica Lino ML series 785880c en
Page 20
DE
EN
FR
IT
ES
PT
NL
DA
SV
NO
FI
JA
ZH
KO
PL
HR
HU
RU
CZ
EL
LT
LV
EE
SL
SK
TR
BG
RO
Technical data
Leica Lino ML90 and ML180
Operation range * (with receiver at
the center of the line)
Self leveling accuracy
(@25°C/77°F)
Self-levelling range +/- 5°
Self leveling time < 10 sec.
Angular accuracy 0.2 mm/m
Laser diode type 635 nm, laser class 2
Fan angle 120°
Protection IP54
Operation temperature -10 - +45°C 14°F - +113°F -10 - +45°C 14°F - +113°F
Storage temperature -25 - +70°C -13°F - +158°F -25 - +70°C -13°F - +158°F
Battery type Type D, 2 x 1,5V
Average battery operation time
alkaline / NiMH
Dimensions
Weight with batteries 2200 g 77 oz 2200 g 77 oz
* depending on lighting conditions
All rights reserved for changes (on drawings, descriptions and technical data).
up to 100 m 328 ft up to 100 m 328 ft
0.7 mm @10 m 1/32 inch @30 ft 0.7 mm @10 m 1/32 inch @30 ft
250 x 159 x
Lino ML90 Lino ML180
20 hrs (Alkaline)
16 hrs (rechargeable)
230 mm
9.9 x 6.3 x
9.1 inch
Leica Lino ML series 785880c en
19
10 hrs (Alkaline)
12 hrs (rechargeable)
250 x 159 x
230 mm
Technic a l d a t a
9.9 x 6.3 x
9.1 inch
Page 21
DE
EN
FR
IT
ES
PT
NL
DA
SV
NO
FI
JA
ZH
KO
PL
HR
HU
RU
CZ
EL
LT
LV
EE
SL
SK
TR
BG
RO
Leica RVL100 and XCR Catch
Reception range up to 80 m 265 ft up to 100 m 328 ft
Smart Targeting range* - - up to 50 m 160 ft
Sensitivity (switchable) ±1 mm/±3 mm ±0,04/±0,12 inch
Length of reception
window
Protection IP54 IP65
Operation temperature -10 - +50°C 14°F - +122°F -10 - +50°C 14°F - +122°F
Storage temperature -25 - +70°C -13°F - +158°F -25 - +70°C -13°F - +158°F
Battery type 1x 6LR61, 9V 3x 1,5V AA
Dimensions
Weight with batteries 260 g 9.1 oz 310 g 10.8 oz
* Range for Smart Targeting can be reduced when working outdoors or close to metal structures
NiMH battery pack (part no. 784966)
42 mm 1,65 inch 86 mm 3,4 inch
147.5 x 75.5 x
29.5 mm
RVL100 XCR Catch
±1 mm/±3 mm/
±5 mm
5.8 x 2.9 x 1.2 inch
190.5 x 75.5 x
29.5 mm
7.5 x 3.0 x 1.2 inch
NiMH charger/adapter (part no. 784967)
Input voltage 3.3 V
Input current 2 A
Charge time 8 h
Input voltage 100-240 V AC 50-60 Hz
Output voltage 3.3 V
Output current 2 A
Technic a l d a t a
20
Leica Lino ML series 785880c en
±0,04/±0.12/
±0,2 inch
Page 22
DE
EN
FR
IT
ES
PT
NL
DA
SV
NO
FI
JA
ZH
KO
PL
HR
HU
RU
CZ
EL
LT
LV
EE
SL
SK
TR
BG
RO
Care and transport
Transport
Transport in the field
When transporting the equipment in the field, always
make sure that you
• either carry the product in its original transportcontainer,
• or carry the tripod with its legs splayed across
your shoulder, keeping the attached product
upright.
Transport in a road vehicle
Never carry the product loose in a road vehicle, as it
can be affected by shock and vibration. Always carry
the product in its transport container and secure it.
Shipping
When transporting the product by rail, air or sea,
always use the complete original Leica Geosystems
packaging, transport container and cardboard box, or
its equivalent, to protect against shock and vibration.
Shipping, transport of batteries
When transporting or shipping batteries, the person
in charge of the product must ensure that the applicable national and international rules and regulations
are observed. Before transportation or shipping,
contact your local passenger or freight transport
company.
Leica Lino ML series 785880c en
Storage
Product
Respect the temperature limits when storing the
equipment, particularly in summer if the equipment is
inside a vehicle. Refer to "Technical Data" for information about temperature limits.
NiMH Batteries
• Refer to "Technical Data" for information about
storage temperature range.
• A storage temperature range of 0°C to +20°C /
32°F to 68°F in a dry environment is recommended to minimize self-discharging of the
battery.
• At the recommended storage temperature range,
batteries containing a 10% to 50% charge can be
stored up to one year. After this storage period
the batteries must be recharged.
• Remove batteries from the product and the
charger before storing.
• After storage recharge batteries before using.
• Protect batteries from damp and wetness. Wet or
damp batteries must be dried before storing or
use.
Alkaline Batteries
If the equipment is to be stored for a long time,
remove the alkaline batteries from the product in
order to avoid the danger of leakage.
21
Care and transport
Page 23
DE
EN
FR
IT
ES
PT
NL
DA
SV
NO
FI
JA
ZH
KO
PL
HR
HU
RU
CZ
EL
LT
LV
EE
SL
SK
TR
BG
RO
Cleaning and Drying
Product and Accessories
• Blow dust off optical parts.
• Never touch the glass with your fingers.
• Use only a clean, soft, lint-free cloth for cleaning.
If necessary, moisten the cloth with water or pure
alcohol.
• Do not use other liquids; these may attack the
polymer components.
Damp Products
• Dry the product, the transport container, the
foam inserts and the accessories at a temperature not greater than 40°C / 104°F and clean
them.
• Do not repack until everything is completely dry.
Cables and Plugs
• Keep plugs clean and dry.
• Blow away any dirt lodged in the plugs of the
connecting cables.
Care and transport
22
Leica Lino ML series 785880c en
Page 24
DE
EN
FR
IT
ES
PT
NL
DA
SV
NO
FI
JA
ZH
KO
PL
HR
HU
RU
CZ
EL
LT
LV
EE
SL
SK
TR
BG
RO
Safety instructions
The person responsible for the instrument must
ensure that all users understand these directions and
adhere to them.
Symbols used
The symbols used have the following meanings
WARNING:
Indicates a potentially hazardous situation or
an unintended use which, if not avoided, will result in
death or serious injury.
CAUTION:
Indicates a potentially hazardous situation or
an unintended use which,if not avoided, may result in
minor injury and/or appreciable material, financial
and environmental damage.
Important paragraphs which must be adhered
to in practice as they enable the product to be used
in a technically correct and efficient manner.
Permitted use
• Projection of horizontal and vertical laser lines
and laser dots
Leica Lino ML series 785880c en
Prohibited use
• Using the product without instruction
• Using outside the stated limits
• Deactivation of safety systems and removal of
explanatory and hazard labels
• Opening of the equipment by using tools (screwdrivers, etc.), as far as not specifically permitted
for certain cases
• Carrying out modification or conversion of the
product
• Deliberate dazzling of third parties; also in the
dark
• Inadequate safeguards at the surveying site.
Limits of use
Refer to section "Technical data".
The Leica Lino is designed for use in areas permanently habitable by humans. Do not use the product
in explosion hazardous areas or in aggressive environments.
Areas of responsibility
Responsibilities of the manufacturer of the original
equipment Leica Geosystems AG, CH-9435 Heerbrugg
(for short Leica Geosystems):
Leica Geosystems is responsible for supplying the
product, including the User Manual in a completely
safe condition.
23
Safety instructions
Page 25
DE
EN
FR
IT
ES
PT
NL
DA
SV
NO
FI
JA
ZH
KO
PL
HR
HU
RU
CZ
EL
LT
LV
EE
SL
SK
TR
BG
RO
Leica Geosystems is not responsible for third
party accessories.
Responsibilities of the person in charge of the
instrument:
The person in charge of the instrument has the
following duties:
• To understand the safety instructions on the
product and the instructions in the User Manual.
• To be familiar with local safety regulations
relating to accident prevention.
Noise emissions
CAUTION:
The A-weighted sound pressure level of the
signal sound is > 80 db(A) at a distance of one meter.
Do not hold the laser receiver directly to your
ear!
Hazards in use
CAUTION:
Watch out for erroneous measurements if the
instrument is defective or if it has been dropped or
has been misused or modified.
Carry out periodic test measurements.
Particularly after the instrument has been subject to
abnormal use, and before, during and after important
measurements.
Refer to section "Checking the accuracy of the Leica
Lino".
Safety instructions
WARNING:
Flat batteries must not be disposed of with
household waste. Care for the environment and take
them to the collection points provided in accordance
with national or local regulations.
The product must not be disposed of with
the household waste.
Dispose of the product appropriately
in accordance with the national regulations
in force in your country.
Always prevent access to the product by
unauthorised personnel.
Product specific treatment and waste management
information can be downloaded from the Leica
Geosystems home page or received from the Leica
Geosystems dealer.
WARNING
Using a battery charger not recommended by
Leica Geosystems can destroy the batteries. This can
cause fire or explosions.
Precautions:
Only use chargers recommended by Leica
Geosystems to charge the batteries.
Electromagnetic Compatibility (EMC)
WARNING
The Leica Lino conforms to the most stringent
requirements of the relevant standards and regula-
24
Leica Lino ML series 785880c en
Page 26
DE
EN
FR
IT
ES
PT
NL
DA
SV
NO
FI
JA
ZH
KO
PL
HR
HU
RU
CZ
EL
LT
LV
EE
SL
SK
TR
BG
RO
tions. Yet, the possibility of it causing interference in
other devices cannot be totally excluded.
FCC Statement, Applicable in U.S.
WARNING
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communication.
However, there is no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and the receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Leica Lino ML series 785880c en
WARNING
Changes or modifications not expressly
approved by Leica Geosystems for compliance could
void the user's authority to operate the equipment.
25
Safety instructions
Page 27
DE
EN
FR
IT
ES
PT
NL
DA
SV
NO
FI
JA
ZH
KO
PL
HR
HU
RU
CZ
EL
LT
LV
EE
SL
SK
TR
BG
RO
Laser classification
The Leica Lino produces visible laser beams, which are
emitted from the instrument:
Lino ML90
Lino ML180
Safety instructions
It is a Class 2 laser product in accordance with:
• IEC 60825-1: 2014-03 "Radiation safety of laser
products"
Laser Class 2 products:
Do not stare into the laser beam or direct it towards
other people unnecessarily. Eye protection is
normally afforded by aversion responses including
the blink reflex.
WARNING:
Looking directly into the beam with optical aids
(e.g. binoculars, telescopes) can be hazardous.
CAUTION:
Looking into the laser beam may be hazardous
to the eyes.
Description Value
Maximum peak radiant
output power < 1.0 mW
Wavelength 638 nm
Pulse duration 70 μs
Pulse repetition frequency 10 kHz
Beam divergence
26
Leica Lino ML series 785880c en
180
°
Page 28
DE
EN
FR
IT
ES
PT
NL
DA
SV
NO
FI
JA
ZH
KO
PL
HR
HU
RU
CZ
EL
LT
LV
EE
SL
SK
TR
BG
RO
Labeling
Lino ML90
Lino ML180
Leica Lino ML series 785880c en
Warranty
This product comes with a three* year warranty from
Leica Geosystems.
All rights reserved for changes (drawings, descriptions and technical specifications).
*) To receive the three year warranty, the product
must be registered on our website within eight
weeks of the purchase date. If the product is not
registered, a two year warranty applies.
27
Warranty
Loading...