Legrand TITAN User Manual
6. Tighten the mounting screws, insert the label, attach the wall plate, and
restore power to the circuit.
7. Calibrate the Dimmer if necessary – Refer to Single Gang Installation
Instructions, step #7.
3. Connect the dimmer as shown in the wiring diagram using the appropriate
sized wire connectors.
4. With the word “TOP” up, install dimmer in the wall box using mounting
screws provided (leave mounting screws “finger tight” at this point).
ins are removed between adjacent dimmers
F
TITAN
™
INSTALLATION INSTRUCTIONS
INCANDESCENT DIMMERS, MAGNETIC LOW VOLTAGE DIMMERS,
FAN SPEED CONTROLS, DEHUMMER FAN SPEED CONTROLS,
FLUORESCENT DIMMERS
/N 340840 Rev. B
P
Couplers
MULTI GANG INSTALLATION INSTRUCTIONS
FINS ARE REMOVED
NOTE: A 3 gang Installation
of Narrow Dimmers is shown and
described below. Any Combination of
Wide and Narrow Dimmers will gang
the same way.
1. Select the correct box size from
Table 3.
Table 3 – Wall-box Gang
Requirements – FINS are REMOVED
Narrow Dimmers
Wide Dimmers
2. Remove the End Cap and break the fins between adjacent dimmers (2 screws
for each End Cap). Keep these screws as they will be needed at step #5.
NOTE: The End Cap and the Fins that are not between dimmers do NOT
get r
emo
ved.
0 1 23456
0 0 1 2 3 456
1 1345678
2 3456789
3 5 6 7 8 9 10 11
4 7
5 9
8 9 10 11 12 13
10 11 12 13 14 15
6 11 12 13 14 15 16 17
e this
v
Remo
screw to
remove End Cap
End Cap
e this
v
Remo
screw to
remove End Cap
Remove fins
between
adjacent
dimmers
using a
vise or
heavy-duty
pliers
5. Attach the Small Couplers between the Dimmers with the screws that were
removed in step 2.
Small Couplers
6. Tighten the mounting screws, insert the label, attach the wall plate, and
restore power to the circuit.
7. Calibrate the Dimmer if necessary – Refer to Single Gang Installation
Instructions, step #7.
ARRANTIES
W
Lifetime Warranty. The device you have purchased is warranted under normal use
against defects in workmanship and materials for as long as you own the device. If the
device fails due to manufacturing defect during normal use, return the device for
eplacement to the store where purchased or send to:
r
Pass & Seymour Legrand
50 Boyd Avenue
acuse, NY 13209
Syr
All requests for replacement must include a dated sales receipt (legible copies
acceptable).
ALL OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO A
PERIOD OF TWO YEARS FROM THE DATE OF PURCHASE. YOUR SOLE AND EXCLUSIVE
REMEDY AGAINST PASS & SEYMOUR LEGRAND UNDER ANY WARRANTY SHALL BE THE
ALENT REPLA
EQUIV
APPLY TO ANY DEFECT ARISING OUT OF ANY ALTERATION OF THE DEVICE, IMPROPER
WIRING, IMPROPER INSTALLATION, MISUSE, ABNORMAL USE OR NEGLIGENCE. IN NO
EVENT SHALL PASS & SEYMOUR LEGRAND BE LIABLE FOR LOST PROFITS, INDIRECT,
SPECIAL, EXEMPLARY, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do
not allow limitations on how long implied warranties last and do not allow exclusion or
ation of incident
limit
exclusions may not apply to every purchaser.
P.O. Box 4822, Syracuse, NY 13221-4822
(800-223-4185)
www.passandseymour.com P/N 340840 Rev. B
CEMENT OF THE DEVICE. IN NO EVENT SHALL ANY W
onsequential damages. Some of the abo
al or c
e limit
v
ARRANTY
ations or
CAUTION: To be installed by a certified electrician or other qualified person.
INCANDESCENT DIMMERS “CD” SERIES: These dimmers are for use with
Incandescent and Halogen lamps.
CAUTION: To reduce the risk of overheating and possible damage to other
equipment, do not install to control a receptacle, a fluorescent light, a motoroperated appliance, or a transformer supplied appliance.
• Do not use this dimmer with incandescent lamps whose power
requirements exceeds maximum power (stated in Watts) of this control.
• Do not connect this dimmer to power source other than 120VAC, 60 Hz only.
• Use copper wire only.
• A 50W minimum load is required.
MAGNETIC LOW VOLTAGE DIMMERS “CDLV” SERIES: These dimmers are for
use with Magnetic Low Voltage Incandescent and Halogen lamps.
CAUTION: To reduce the risk of overheating and possible damage to other
equipment, do not install to control a receptacle, a fluorescent light, or a
motor-operated appliance. Connect only in a 120VAC, 60Hz circuit to control
the primary winding of a transformer supplied incandescent and halogen
lamp. The maximum VA rating of this dimmer applies to the transformer
input, not the load on the transformer secondary.
• Do not use to control a solid state electronic low voltage transformer.
• Do not use with inoperative or missing lamps. Use of this dimmer with
inoperative or missing lamps can create an over current condition which
may damage the transformer. Use transformers that incorporate thermal
protection or a fuse at the primary windings.
• Use copper wire only.
• A 50VA minimum load is required.
FAN SPEED CONTROLS “CDSC” SERIES: These controls are for use with Fan
or Blower units. Use only with Fan or Blower units marked “Suitable for Use
with Solid State Fan Speed Controls”. Set multi-speed fans to their highest
setting before installing this control.
• Do not use this control with Fan or Blower units that exceed the maximum
power (stated in Amps) of this control.
• Do not connect this control to power source other than 120VAC, 60 Hz only.
• Use copper wire only.
• A 0.25 Amp minimum load is required.
DEHUMMER FAN SPEED CONTROLS “CDDH” SERIES: These controls are for
use with a single ceiling paddle fan only.
• Do not use this control with a ceiling paddle fan that exceeds the maximum
power (stated in Amps) of this control.
• Do not connect this control to power source other than 120VAC, 60 Hz only.
• Use copper wire only.
FLUORESCENT DIMMERS “CDFB” SERIES: These dimmers control dimmable
ballasts:
• Use copper wire only.
• A 0.25 Amp minimum load is required.
• These dimmers are compatible with the following ballasts:
Compatible
P&S Cat #
CDFB5
CDFB8
CDFB53P
CDFB83P
CDFB10
CDFB16
CDFB103P
CDFB163P
CDFB7-277
CDFB10-277
CDFB73P-277
CDFB103P-277
Voltage
120VAC
60 HZ
277VAC
60 HZ
Ballast
Manufacturer
Advance
Lutron
am
ania/Osr
v
Syl
e
anc
Adv
Sylvania/Osram
Model
REZ-132-SC, REZ-2S32-SC, REZ-3S32-SC,
REZ-154, REZ-2S54, REZ-1Q18-M2, REZ2Q18-M2, REZ-1T42-M2, REZ-2T42-M3,
REZ-1TTS40/REZ-1TTS40-SC, REZ2TTS40/REZ-2TTS40-SC,IEZ-2S24-D, REB2S26-M1-LS-DIM/REB-2S26-M1-BS-DIM
2W-T426-120-1-S, 2W-T426-120-2-S, 2WT432-120-1-S, 2W-T432-120-2-S, 2WT832-120-1-S, 2W-T832-120-2-S
QTP1x32T8/UNV DIM, QTP2x32T8/UNV
DIM, QTP3x32T8/UNV, DIM, QTP4x32T8/
UNV DIM
VEZ-132-SC, VEZ-2S32-SC, VEZ-3S32-SC,
VEZ-154, VEZ-2S54, VEZ-1Q18-M2, VEZ2Q18-M2, VEZ-1T42-M2, VEZ-2T42-M3,
VEZ-1TTS40/VEZ-1TTS40-SC, VEZ-2TTS40/
VEZ-2TTS40-SC, IEZ-2S24-D
QTP1x32T8/UNV DIM, QTP2x32T8/UNV
DIM, QTP3x32T8/UNV, DIM, QTP4x32T8/
UNV DIM
PACKAGE CONTENTS
One of the following Dimmers:
Narr
ow Dimmers Wide Dimmers
Cat no.: Cat no.: Cat no.: Cat no.:
CD700 CD703P CD1600 CD1603P
CD1100 CD1103P CD2000 CD2003P
CDLV700 CDLV703P CDLV1600 CDLV1603P
CDLV1100 CDLV1103P CDFB10 CDFB103P
CDFB5 CDFB53P CDFB16 CDFB163P
CDFB8 CDFB83P CDFB7-277 CDFB73P-277
CDSC6 CDFB10-277 CDFB103P-277
CDDH16 CDSC12
Wire Nuts Coupler Small Coupler
WARNING: To prevent severe shock or electrocution, always turn power
OFF at the service panel before installing this dimmer, working on the
circuit, or changing a lamp.
• To be installed by a certified electrician or other qualified person.
WALL PLATE LABELING SYSTEM
These dimmer wall plates contain a label holding slot. A
0.33" x 1.5" label can be placed in this label holding slot.
These labels can be printed from an Avery®standard
template: Divider tab inserts 8-Tabs or equivalent.
Install the label with the following procedure:
1. Disconnect power to the circuit by removing fuse or
turning circuit breakers OFF.
2. Remove the wall plate by
placing a small flat head
screwdriver into one of
the four slots located at
the top and bottom of the
wall plate. Gently twist a
half turn until the plate
pops off.
3. Slide the label in from the
back side of the wall
plate (as shown at right).
WIRING INFORMATION
IMPORTANT NOTES Read the following before installation:
• Requirements for wire strip length and wire connections.
WIRE NUT USAGE CHART
Wire Combinations Strip Lengths Color
1#14 & 1#16; 1#14 & 2#18; 2,3#16; 1/2" Except 9/16" Orange
1#16 & 1-3#18; 3-5#18; 2#18 For #16 & #18 AWG
1#10 & 1#14; 1#12 & 1#14 2, 3#14; 1/2" Except 5/8" Yellow
2#14 & 1,2#16; 2#14 & 2,3#18; For #16 AWG
1#14 & 1-4#16; 1#14 & 1-4#18
1#10 & 1,2#12; 1#10 & 1-3#14; 2,3#12; 7/16" Except 1/2" Red
1#12 & 1-3#14; 1#12 & 3#16; 3,4#14 For #16
1#14 & 1,2#16; 1#14 & 1,2#16; 7/16" For #14 & #16 Ivory
2,3#16; 2-5#18 1/2" For #18
Use Only Copper Wire With This Device.
• Use a separate neutral wire for each phase of a multiphase system
containing a dimmer, and for high power single phase applications where
flickering is present.
• All dimmers can be damaged by improper wiring. Check for short circuits
prior to installing the dimmer.
Procedure for short circuit check:
a. Disconnect power to the circuit by removing fuse or turning circuit
breakers OFF.
b. Install a switch instead of the dimmer. Turn the switch to the “on” position.
c. Turn power ON. If the circuit breaker trips, a short is present. If the light
fails to turn ON and OFF with the switch, the wiring may be incorrect.
d. Correct wiring, if necessary and retest.
e. Install the dimmer only after the light operates properly with the switch.
• Protect from dirt and dust. The dimmer can be damaged from
contaminates encountered during the construction process. If lighting is
required prior to the construction process completion, then a switch should
be temporarily installed in place of the dimmer. The dimmer should not be
installed until the construction process is complete.
• Any dimmer damaged by improper installation is not covered under warranty.
• It is normal for the dimmer to feel warm during operation.
• Cleaning Instructions: Wipe dimmer with a damp, clean cloth.
DO NOT clean the dimmer with chemicals or cleaning solutions.
WIRING DIAGRAMS
Table 1
Dimmer Catalog # Diagram #
CD700, CD1100, CDLV700, CDLV1100, CD1600, CDLV1600,
CD2000, CDFB5, CDFB8, CDFB10, CDFB16, CDFB7-277, 1
CDFB10-277, CDDH16, CDSC6, CDSC12
For Single Pole Installation of: CD703P, CD1103P, CDLV703P,
CDLV1103P, CD1603P, CDLV1603P, CD2003P, CDFB53P, CDFB83P, 2
CDFB103P, CDFB163P, CDFB73P-277, CDFB103P-277
ay Installation of:
or 3-W
F
V1103P, CD1603P, CDL
CDL
CDFB103P, CDFB163P, CDFB73P-277, CDFB103P-277
allation of
t
ay Ins
or 4-W
F
V1103P, CD1603P, CDL
CDL
CDFB103P, CDFB163P, CDFB73P-277, CDFB103P-277
DIAGRAM 2 (Single-Pole Wiring Using 3-Way Preset Dimmer)
CD703P, CD1103P, CDL
V1603P, CD2003P, CDFB53P, CDFB83P, 3
: CD703P, CD1103P, CDL
V1603P, CD2003P, CDFB53P, CDFB83P,
GRAM 1 (Singl
DIA
e-P
e Wiring)
ol
V703P,
V703P,
4
DIAGRAM 3 (3-Way Wiring)
DIAGRAM 4 (4-Way Wiring)
SINGLE GANG INSTALLATION INSTRUCTIONS
1. Disconnect power to circuit by removing fuse or turn
circuit breakers OFF before installing.
For existing installations: Remove wall plate and
2.
switch mounting screws, pull existing switch from wall
box. For new installations: Install a 1-gang wall-box.
3. Disconnect existing switch from circuit.
3-way installation: Identify the “COMMON” wire (wire
connected to the terminal marked common or odd
colored terminal). For “new” installation identify wire
connected to power source or to the load.
4. Connect dimmer as shown in the wire diagram with
appropriate sized wire connectors (see Table 1).
5. Install dimmer in wall box, with the word “TOP” up, using mounting screws provided.
6. Insert the label, attach the wall plate and restore power to the circuit.
7. Dimmer Set-up Adjustments:
Incandescent Dimmer: The Full ON voltage can be reduced to save energy
a.
by reducing the Full ON light level. To change the Full ON light level, slide
the dimmer knob up to its full brightness. DISCONNECT POWER FROM
CIRCUIT, and remove the wall plate. Use a small insulated, screwdriver to
adjust the trim potentiometer. Turn down to decrease the Full ON light level.
Magnetic Low Voltage Dimmer: The minimum light level may need
b.
adjustment for variations in low voltage transformers. To change the
minimum light level, slide the dimmer knob down to the lowest
brightness. DISCONNECT POWER FROM CIRCUIT, and remove the wall
plate. Use a small insulated, screwdriver to adjust the trim
potentiometer. Turn down to decrease the minimum light level.
c.
Fan Speed Controls: The minimum fan speed level may need adjustment
for variations in fans. To change the minimum fan speed, slide the knob
down to the lowest level. DISCONNECT POWER FROM CIRCUIT, and
remove the wall plate. Use a small insulated, screwdriver to adjust the
trim potentiometer. Turn down to decrease the fan speed. Make certain
that the fan does not “stall” in any of the ON positions as overheating of
the fan may occur. DO NOT USE THE FAN PULL CHAIN TO CHANGE
SPEEDS AFTER THIS CONTROL IS INSTALLED. THE FAN PULL CHAIN
NEEDS TO REMAIN AT THE MAXIMUM SPEED.
d. Dehummer Fan Speed Controls: No adjustments required. Make certain
that the fan does not “stall” in any of the ON positions as overheating of
the fan may occur. DO NOT USE THE FAN PULL CHAIN TO CHANGE
SPEEDS AFTER THIS CONTROL IS INSTALLED. THE FAN PULL CHAIN
NEEDS TO REMAIN AT THE MAXIMUM SPEED.
e. Fluorescent Dimmer: The
minimum light level may need
adjustment for variations in
ballasts. To change the
minimum light level, slide the
dimmer knob down to the
lowest brightness. DISCONNECT
POWER FROM CIRCUIT, and
remove the wall plate. Use a
small insulated, screwdriver to
adjust the trim potentiometer.
Turn up to increase the
minimum light level.
Knob
Trim Potentiometer
NOTE: Never adjust
trim potentiometer
when circuit is live.
MULTIPLE GANGING OF DIMMERS
Any combination of dimmer models may be ganged together. Using a vise or heavy-duty pliers, remove the fins on either or both sides of the heat sink, as
necessary. Dimmers can be ganged without removing fins by proper selection and placement of outlet boxes (see Table 2 and
Table 3). When Dimmers are ganged, De-rate the maximum load according to the following De-Rating Table 1:
Table 1 – Derating for Multi-Gang Installations
Fins are NOT Removed Fins are Removed
Dimmer 1-Gang 2-Gang 3- or more Gang 2-Gang 3- or more Gang
Catalog # Installation Installation Installation Installation Installation
CD700 700W 700W 700W 700W 700W
CDLV700 700VA 700VA 700VA 700VA 700VA
CD703P 700W 700W 700W 700W 700W
CDLV703P 700VA 700VA 700VA 700VA 700VA
CD1100 1100W 1100W 1000W 1000W 900W
Narrow
Dimmers
Wide CDFB10 10A 10A 10A 10A 10A
Dimmers CDFB16 16A 16A 16A NO FINS TO REMOVE
MULTI GANG INSTALLATION INSTRUCTIONS
NOTE: A 3-gang Installation of Narrow Dimmers is shown and described
below. Any Combination of Wide and Narrow Dimmers will gang the same way.
1. Select the correct box size from Table 2.
Table 2 – Wall-box Gang Requirements – FINS are NOT REMOVED
Wide Dimmers
0 0 1 1+1* 4 4+1* 7 7+1*
1 13 56 8 911
2 4 5 7 8 10 11 13
3 6 8 9 11 12 14 15
4 9 10 12 13 15 16 -
5 11 13 14 16 – – -
6 14 15 – – – –
*Wall Box Requirements for Ganging an Even Number of Narrow Dimmers.
4+1 set up shown below:
4-gang
x
wall bo
CDLV1100 1100VA 1100VA 1000VA 1000VA 850VA
CD1103P 1100W 1100W 1000W 1000W 950W
CDLV1103P 1100VA 1100VA 1000VA 1000VA 850VA
CDFB5 5A 5A 5A 5A 5A
CDFB8 8A 8A 8A 7.7A 6.3A
CDFB53P 5A 5A 5A 5A 5A
CDFB83P 8A 8A 8A 7.7A 6.3A
CDSC6 6A 6A 6A 6A 6A
CDDH16 1.6A 1.6A 1.6A 1.6A 1.6A
CD1600 1600W 1600W 1600W 1600W 1550W
CDLV1600 1600VA 1600VA 1600VA 1600VA 1550VA
CD1603P 1600W 1600W 1600W 1600W 1550W
CDLV1603P 1600VA 1600VA 1600VA 1600VA 1550VA
CD2000 2000W 2000W 2000W
CD2003P 2000W 2000W 2000W
CDFB7-277 7A 7A 7A 7A 7A
CDFB10-277 10A 10A 10A 10A 10A
CDSC12 12A 12A 12A 12A 12A
CDFB103P 10A 10A 10A 10A 10A
CDFB163P 16A 16A 16A NO FINS TO REMOVE
CDFB73P-277 7A 7A 7A 7A 7A
CDFB103P-277 10A 10A 10A 10A 10A
2. Remove the End Cap between adjacent dimmers (2 screws for each End
FINS ARE NOT REMOVED
w Dimmers
o
Narr
01 2 3 4 56
2.712
1-gang
x
wall bo
Chase nippl
e
Cap). Keep these screws as they will be needed at step #5.
Remove this screw to remove End Cap
End Cap
Remove this screw to remove End Cap
NOTE:
The End Cap that is not between dimmers does not get removed.
3. Connect the dimmer as shown in the wiring diagram using the appropriate
sized wire connectors.
4. With the word “TOP” up, install dimmer in the wall box using mounting
screws provided (leave mounting screws “finger tight” at this point).
5. Attach the Couplers between the Dimmers with the screws that were
removed in step 2.
NO FINS TO REMOVE
Loading...