47
47
B
A
131
53
52
42
98
42
86
53
87
98
Setscrew
Bracket
Channel
Channel nut
Swiftrack® channel support system
framework brackets
All framework brackets are manufactured to BS 6946 from steel which
complies with BS EN 10025 Grade S275JRC and are supplied singly.
Channel nuts and setscrews are not supplied with brackets, therefore
must be ordered separately
■ Dimensions and weights
Made from 5 or 6 mm thick steel unless otherwise stated
Brackets are 40 mm wide and have 14 mm diameter holes to accept
M12 (or smaller) setscrews
All bend radii are 5 mm unless otherwise stated
Weights
All weights given are in kilograms (kg) based on nominal thickness and
are for hot dip galvanised finish. For weights in stainless steel finish
contact us on +44 (0) 845 605 4333
Loads
All loads are for hot dip galvanised brackets fixed with M12 setscrews
and M12 zinc plated channel nuts. Loads for stainless steel brackets
are available on request - contact us on +44 (0) 845 605 4333
Minimum Yield Stress of material is 275 N/mm
2
Only M10 or M12 channel nuts and bolts should be used for the
attachment of load-bearing brackets
In most cases the mode of failure will be slippage of the bracket along
the channel. However there are few channel/bracket combinations
where the maximum load is dependant upon the strength of the
bracket itself
■ Finishes and standards
The standard finish for all framework brackets and beam clamps is hot
dip galvanised steel to BS EN ISO 1461
Stainless steel to
BS EN 10088 : Grade 1.4404 (equivalent to S316L31)
is also available as an alternative where applicable. To order stainless
steel finish add S to the end of the standard catalogue number
For example : SB500S
■ Assembly
Fasteners (not included)
Fixing brackets to Swiftrack channel
■ 90° brackets
SB500
SB501
SB502
SB503
Maximum load on each bracket with both
ends supported : A = 350kgf. B = 174kgf
Unit weight (kg) : 0·125
A
Maximum load on each bracket :
A = 180kgf
Unit weight (kg) : 0·125
A
Maximum load on each bracket :
A = 230kgf
Unit weight (kg) : 0·191
A
Maximum load on each bracket with both
ends supported : A = 120kgf
Unit weight (kg) : 0·191
Standard fasteners for Swiftrack are high tensile hexagon head
setscrews to BS 3692-8.8, these being zinc plated to BS 3382 : Part 2
The use of too long a fastener will prevent proper tightening because
the bolt end will foul the bottom of the channel before the head tightens
down on the fitting
When fastening brackets other than Swiftrack, longer bolts may be
required if the bracket thickness is greater than 8 mm
For channel nuts, see p. 101
Channel Backplate
type thickness
Deep channel 6 mm and 8 mm M10 or M12 x 35 mm
SC400 series 5 mm and 6 mm M10 or M12 x 20 mm
Shallow channel 7 mm and 8 mm M10 or M12 x 25 mm
SC200 series 5 mm and 6 mm M10 or M12 x 20 mm
(1) The use of too long a fastener will prevent proper tightening because the bolt end will foul
the bottom of the channel before the head tightens down on the fitting
(2) When fastener brackets other than Swiftrack, longer bolts may be required if the bracket
thickness is greater than 8 mm
Recommended
fasteners
(1)
(2)
(2)
SB504
SB505
A
Maximum load on each bracket :
A = 120kgf
Unit weight (kg) : 0·257
A
Maximum load on each bracket :
A = 300kgf
Unit weight (kg) : 0·257
104
All dimensions (mm) are nominal
105
90
45
20
45
94
130
96
90
43
50
45
20
40
40
85
40
20
20
130
40
20
20
220
40
20
20
175
40
20
20
47·5
47
47
26
46
141
54
25
141
48
54
90
142
43
50
45
20
45
90
88
96
Swiftrack® channel support system
framework brackets (continued)
■ 90° brackets (continued)
SB550
SB551
SB552
A
Maximum load on each bracket :
A = 600kgf
Unit weight (kg) : 0·359
A
Maximum load on each bracket :
A = 600kgf
Unit weight (kg) : 0·516
A
■ Square plates and splice plates
Square plates
Unit
weight
Cat. Nos.
SB50606 M6 0·063
SB50608 M8 0·062
SB50610 M10 0·061
SB50612 M12 0·058
Use as location plate when attaching any special fitment which will not
sit across both channel sides
Splice plates
Holes spaced at 45 mm centres
SB507
Unit weight (kg) : 0·125
SB509
Fasteners
(kg)
SB508
Unit weight (kg) : 0·191
SB510
SB556
Maximum load on each bracket :
A = 700kgf. 5mm thick.
Unit weight (kg) : 0·488
A
Maximum load on each bracket with
both ends supported : A = 260kgf
Unit weight (kg) : 0·478
Unit weight (kg) : 0·257
Unit weight (kg) : 0·323
■ U and Z brackets
U bracket
SB514 SB515
Unit weight (kg) : 0·243
Z bracket
SB511
Unit weight (kg) : 0·179
Hole on one side of bracket only
Unit weight (kg) : 0·307
SB513
Unit weight (kg) : 0·150
All dimensions (mm) are nominal
90
40
ϑ
A
90
ϑ
138
48
48
48
45
140
45∞
50
90
90
50
130
90
50
140
51
120
40
80
40
40
175
45
175
23
85
95
41
47
40
80
40
80
90
90
Swiftrack® channel support system
framework brackets (continued)
■ Angle brackets and plates
Obtuse angle brackets
Unit
weight
Cat. Nos. Angle (kg)
SB520 15 0·197
SB524 45 0·197
SB526 60 0·197
SB528 75 0·197
Acute angle brackets
Unit
A weight
Cat. Nos. Angle (mm) (kg)
SB532 45 65 0·237
SB534 60 46 0·197
SB536 75 46 0·197
■ T brackets and plates
T plate
SB554
SB555
■ Joining brackets and channels
Jointing bracket
SB518
Unit weight (kg) : 0·249
Jointing channel
SB651
For SC400 channel. 45 mm deep
Unit weight (kg) : 0·85
SB650
For SC200 channel. 23 mm deep
Unit weight (kg) : 0·55
■ L brackets
L bracket
SB600
Unit weight (kg) : 0·359
T bracket
SB603
Unit weight (kg) : 0·233
Cross plate
SB603+
Unit weight (kg) : 0.284
90° T bracket
SB606
Unit weight (kg) : 0·32
Not available in S finish
45° T bracket
SB607
Unit weight (kg) : 0·163
Left hand
L corner bracket
SB602
Unit weight (kg) : 0·27
Not available in S finish
Right hand
L corner bracket
SB601
Unit weight (kg) : 0·27
Not available in S finish
Unit weight (kg) : 0·35
Not available in S finish
106
Unit weight (kg) : 0·32
Not available in S finish
All dimensions (mm) are nominal
107
86
148·5
149
86
53
48
48
87
98
80
40
140
95
80
40
189
175
252
Outer
holes
Ø20
45
63
20
43
55
20
55
175
Outer
holes
Ø20
45
63
20
55
20
55
84
293
30
48
*28
*25
40
47
*25
*65
*87
80
*22
*41
80
*22
*125
*41
80
*22
*41
40
*25
*16
*37
80
*47
*13
110°
Swiftrack® channel support system
framework brackets (continued) and beam clamps
■ Wing brackets and shelf brackets
2 lug wing bracket
SB700
Unit weight (kg) : 0·492
Angled wing bracket
SB707
Unit weight (kg) : 0·250
Not available in S finish
3 lug wing bracket
SB701
Unit weight (kg) : 0·581
Shelf bracket
SB703
Gusset only, 3 mm thick
Unit weight (kg) : 0·369
■ Base plates and gusseted brackets
Single channel
base plate
SB704
Double channel
base plate
SB705
■ Beam clamps
Beam clamps are supplied singly
Nut, bolts, cone point screws and U bolts where shown are included
Beam clamps conform to BS 6946
Dimensions and weights
All weights given are in kilograms (kg) based on nominal thickness and
are for hot dip galvanised finish unless otherwise stated. For weights in
stainless steel finish contact us on +44 (0) 845 605 4333
Beam clamp
SC850
6 mm
Maximum load : 400kgf/pair
Use in pairs
Not available in S finish
Unit weight (kg) : 0.117
Window
beam clamp
SC852/21
6 mm
For 21 mm channel
Maximum load : 475kgf/pair
Use in pairs
Unit weight (kg) : 0·37
Beam clamp
SC851
6 mm
Maximum load : 200kgf
Unit weight (kg) : 0·208
Window beam clamp
SC852/41
6 mm
For 41 mm channel and
21 mm back-to-back channels
Maximum load : 475kgf/pair
Use in pairs
Unit weight (kg) :
0·52
Distance between hole centres :
100 mm
Unit weight (kg) : 0·618
Single channel gusseted
bracket
SB702
Unit weight (kg) : 1·848
All dimensions (mm) are nominal
Distance between hole centres :
149 mm
Window beam clamp
SC852/82
Beam clamp
SC853
Unit weight (kg) : 0·848
Double channel gusseted
bracket
SB706
6 mm
For 41 mm
back-to-back channels.
Maximum load : 900kgf/pair
Use in pairs
Unit weight (kg) : 0·30
Maximum load : 375kgf/pair
Use in pairs
Not available in S finish
Unit weight (kg) : 0·56
Beam Clamp
Unit weight (kg) : 2·118
SC854
6 mm
Maximum load : 350kgf/pair
Use in pairs
Unit weight (kg) : 0·17
(*) Inside dimensions (mm)
Loading...