Legrand SB500, SC850, SB704, SB509, SB603 Installation Instructions
...
47
47
B
A
131
53
52
42
98
42
86
53
87
98
Setscrew
Bracket
Channel
Channel nut
Swiftrack® channel support system
framework brackets
All framework brackets are manufactured to BS 6946 from steel which
complies with BS EN 10025 Grade S275JRC and are supplied singly.
Channel nuts and setscrews are not supplied with brackets, therefore
must be ordered separately
■ Dimensions and weights
Made from 5 or 6 mm thick steel unless otherwise stated
Brackets are 40 mm wide and have 14 mm diameter holes to accept
M12 (or smaller) setscrews
All bend radii are 5 mm unless otherwise stated
Weights
All weights given are in kilograms (kg) based on nominal thickness and
are for hot dip galvanised finish. For weights in stainless steel finish
contact us on +44 (0) 845 605 4333
Loads
All loads are for hot dip galvanised brackets fixed with M12 setscrews
and M12 zinc plated channel nuts. Loads for stainless steel brackets
are available on request - contact us on +44 (0) 845 605 4333
Minimum Yield Stress of material is 275 N/mm
2
Only M10 or M12 channel nuts and bolts should be used for the
attachment of load-bearing brackets
In most cases the mode of failure will be slippage of the bracket along
the channel. However there are few channel/bracket combinations
where the maximum load is dependant upon the strength of the
bracket itself
■ Finishes and standards
The standard finish for all framework brackets and beam clamps is hot
dip galvanised steel to BS EN ISO 1461
Stainless steel to
BS EN 10088 : Grade 1.4404 (equivalent to S316L31)
is also available as an alternative where applicable. To order stainless
steel finish add S to the end of the standard catalogue number
For example : SB500S
■ Assembly
Fasteners (not included)
Fixing brackets to Swiftrack channel
■ 90° brackets
SB500
SB501
SB502
SB503
Maximum load on each bracket with both
ends supported : A = 350kgf. B = 174kgf
Unit weight (kg) : 0·125
A
Maximum load on each bracket :
A = 180kgf
Unit weight (kg) : 0·125
A
Maximum load on each bracket :
A = 230kgf
Unit weight (kg) : 0·191
A
Maximum load on each bracket with both
ends supported : A = 120kgf
Unit weight (kg) : 0·191
Standard fasteners for Swiftrack are high tensile hexagon head
setscrews to BS 3692-8.8, these being zinc plated to BS 3382 : Part 2
The use of too long a fastener will prevent proper tightening because
the bolt end will foul the bottom of the channel before the head tightens
down on the fitting
When fastening brackets other than Swiftrack, longer bolts may be
required if the bracket thickness is greater than 8 mm
For channel nuts, see p. 101
Channel Backplate
type thickness
Deep channel 6 mm and 8 mm M10 or M12 x 35 mm
SC400 series 5 mm and 6 mm M10 or M12 x 20 mm
Shallow channel 7 mm and 8 mm M10 or M12 x 25 mm
SC200 series 5 mm and 6 mm M10 or M12 x 20 mm
(1) The use of too long a fastener will prevent proper tightening because the bolt end will foul
the bottom of the channel before the head tightens down on the fitting
(2) When fastener brackets other than Swiftrack, longer bolts may be required if the bracket
thickness is greater than 8 mm
Recommended
fasteners
(1)
(2)
(2)
SB504
SB505
A
Maximum load on each bracket :
A = 120kgf
Unit weight (kg) : 0·257
A
Maximum load on each bracket :
A = 300kgf
Unit weight (kg) : 0·257
104
All dimensions (mm) are nominal
105
90
45
20
45
94
130
96
90
43
50
45
20
40
40
85
40
20
20
130
40
20
20
220
40
20
20
175
40
20
20
47·5
47
47
26
46
141
54
25
141
48
54
90
142
43
50
45
20
45
90
88
96
Swiftrack® channel support system
framework brackets (continued)
■ 90° brackets (continued)
SB550
SB551
SB552
A
Maximum load on each bracket :
A = 600kgf
Unit weight (kg) : 0·359
A
Maximum load on each bracket :
A = 600kgf
Unit weight (kg) : 0·516
A
■ Square plates and splice plates
Square plates
Unit
weight
Cat. Nos.
SB50606 M6 0·063
SB50608 M8 0·062
SB50610 M10 0·061
SB50612 M12 0·058
Use as location plate when attaching any special fitment which will not
sit across both channel sides
Splice plates
Holes spaced at 45 mm centres
SB507
Unit weight (kg) : 0·125
SB509
Fasteners
(kg)
SB508
Unit weight (kg) : 0·191
SB510
SB556
Maximum load on each bracket :
A = 700kgf. 5mm thick.
Unit weight (kg) : 0·488
A
Maximum load on each bracket with
both ends supported : A = 260kgf
Unit weight (kg) : 0·478
Unit weight (kg) : 0·257
Unit weight (kg) : 0·323
■ U and Z brackets
U bracket
SB514 SB515
Unit weight (kg) : 0·243
Z bracket
SB511
Unit weight (kg) : 0·179
Hole on one side of bracket only
Unit weight (kg) : 0·307
SB513
Unit weight (kg) : 0·150
All dimensions (mm) are nominal
Loading...