87045 LIMOGES Cedex
Telephone: (+33) 05 55 06 87 87 - Fax: (+33) 05 55 06 88 88
19" LCS2 freestanding cabinets
1. GENERAL FEATURES
19" LSC2 freestanding cabinets are intended for digital infrastructures.
19" LCS2 cabinets are metal and provide IP20 - IK08 protection. They
have a single or double screen-printed curved glass door and are
finished throughout in charcoal grey RAL 7016.
19" LSC2 cabinets can be joined together, either directly or via a
cabling unit, and can be equipped with a modular plinth.
Equipment and accessories for cable management, vertical extension,
thermal management, etc. complete the range.
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
CONTENTS Page
1. General features.................1
2. Range.........................3
3. Technical features ...............4
4. Dimensions.....................5
5. Baying........................10
6. Plinths........................12
7. Cable management .............17
8. Vertical extension ...............20
9. Thermal management ...........21
10. Accessories ...................22
11. 19" equipment .................24
12. Power distribution...............27
1. GENERAL FEATURES (continued)
1.1 Presentation (continued)
The 4 structural uprights and the 2 end plates form a metal framework
that is screwed together. The cabinet can be dismantled completely if
access is difficult.
The end plates contain the cabinet's cable entries. Their configuration,
which is identical for the top and the bottom, is dependent on the
dimensions of the cabinet:
(mm) Width 600 Width 800
1.1 Presentation
The main parts of 19" LCS2 freestanding cabinets are:
- A framework consisting of 4 uprights and 2 end plates
- A single or double screen-printed curved glass front door
- 2 side panels (excluding extension cabinets)
- A rear panel
- 4 x 19" uprights
Depth 600
Depth 800
Depth 1000
Technical data sheet: F01424EN/01
Each cable entry is pre-cut in 19" format in order to be equipped with
a cable entry plate (see section 7.1).
The whole structure stands on 4 levelling feet that can be adjusted
from the inside and the outside of the cabinet.
Updated on: 24/10/2014 Created on: 21/02/2012
1/31
19" LCS2 freestanding cabinets
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
1. GENERAL FEATURES (continued)
1.1 Presentation (continued)
The single front door comprises:
- Curved colourless transparent glass with "pixel" screen-printing on
the vertical edges
- A handle equipped with a 2433A key lock
- 2 metal hinges (3 for 47U height)
The double front door comprises:
- Two half-doors made of curved colourless transparent glass with
"pixel" screen-printing on the external vertical edges
- A locking bolt located at the top of each half-door
- Two metal hinges on each half-door
Doors are removable and single door is reversible.
Locks are compatible with key barrels (other key codes) and inserts
Cat. Nos. 0 368 13/16/17/18/19/20/22/23/24/25/26/27.
For a perfect finish, 2 fascia trims, clipped onto the end plates,
continue the "pixel" design from the door. The upper trim carries the
Legrand name.
The side and rear metal panels are equipped with:
- A 2433A locking bolt
- A stainless steel equipotential link clip
Each panel is removable for total accessibility:
1. GENERAL FEATURES (continued)
1.1 Presentation (continued)
The four 19" uprights have dual marking of the Us and assistance with
depth adjustment for easy installation.
The adjustment is continuous with markings at 12.5 mm intervals:
12.5 mm
The dual marking of the Us enables location in relation to the top or
the bottom of the cabinet:
A
A
B
B
The clip automatically provides continuity of the metal conductive parts
between the panels and the rest of the cabinet (no risk of this being
forgotten).
The lock is compatible with key barrels (other key codes) and inserts
Cat. Nos. 0 368 13/16/17/18/19/20/22/23/24/25/26/27.
In the above example, the marking indicates that this is U no. 14 from
the top and U no. 29 from the bottom of the cabinet.
The 19" uprights are perforated with 9.5 x 9.5 mm square holes.
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
2/31
19" LCS2 freestanding cabinets
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
1. GENERAL FEATURES (continued)
1.2 Standards
19" LCS2 freestanding cabinets comply with the following standards:
IEC 60529
EN 60529
IEC 62262
EN 62262
IEC 60950-1
EN 60950-1
C 77-210-1
EIA-310-E Cabinets, racks, panels and associated
IEC 60297-3-100
DIN 41414-7
19" LCS2 freestanding cabinets can be integrated in installations
complying with the following standards:
EN 50173-1 Information technology -
EN 50174-1 & 2
C 90-480-1 & 2
ISO IEC 11801 Information technology - Generic cabling for
NF C 15-100
Part 4-41
IEC 60364-4-41 Low voltage electrical installations
(NF C 20-010) Degrees of protection provided by
enclosures (IP code)
(NF EN 50102, NF C 20-015) Degrees of
protection provided by enclosures for electrical
equipment against external mechanical impacts
(IK code)
Safety of information technology equipment
equipment (ANSI/EIA/310-E-2005)
(NF C 20-150, NF C 20-151) Dimensions of
mechanical structures of the 482.6 mm series
(19 in)
Generic cabling systems
Information technology - Cabling installation
customer premises
Low voltage electrical installations recommendations
- Protection for safety
- Protection against electric shock
2. RANGE
2.1 Cabinet with single front door
Catalogue
Number
Capacity Width
(mm)
(1)
0 463 00 24U 600 600
0 463 06 29U 600 600
0 463 12 33U 600 600
0 463 18 42U 600 600
0 463 19 42U 600 800
0 463 21 42U 800 600
0 463 22 42U 800 800
0 463 23 42U 800 1 000
0 463 28 47U 800 800
0 463 29 47U 800 1 000
Two extension freestanding cabinets complete the range. These are
supplied without side panels and with a baying kit:
19" LCS2 extension cabinets
Catalogue
Number
Capacity Width
(mm)
(1)
0 463 30 42U 600 600
0 463 33 42U 800 800
2.2 Cabinet with double front door
Door opening suitable for small spaces
Catalogue
Number
Capacity Width
(mm)
(1)
0 463 41 42U 800 600
0 463 42 42U 800 800
0 463 43 42U 800 1 000
Depth
(mm)
Depth
(mm)
Depth
(mm)
(1)
(1)
(1)
To meet specific requirements, the made-to-measure department
offers 40 sizes and various configurations: front and rear door
(microperforations, metal double door…), mounting of equipment,
other colours, etc.
(1)
Designated dimensions. See section 4.1 for overall dimensions.
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
3/31
19" LCS2 freestanding cabinets
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
3. TECHNICAL FEATURES
3.1 Index of protection
- IP20 in accordance with IEC EN 60529
Protected against solid objects whose diameter is larger than 12.5 mm
- IK08 in accordance with IEC EN 62262
Protected against mechanical impact with an energy of 5 joules
3.2 Mechanical performance
- Permissible load: 420 kg
- Resistance to shock acceleration and vibration in accordance with
IEC 61587-1: level DL4
3.3 Design
- Structural uprights and upper end plate 1.5 mm thick
galvanised steel + paint finish
- Lower end plate 1.5 mm thick Z140 MB-C galvanised steel
- Curved front door made of 5 mm thick colourless transparent
safety glass.
Charcoal grey RAL 7016 internal screen-printing on the vertical
edges: 2 x 143 mm in 600 mm width, 2 x 243 mm in 800 mm width.
- Single door handle charcoal grey RAL 7016 polyamide
- Door hinges zamak + paint finish
- Fascia trims charcoal grey RAL 7016 ABS.
Legrand marked in relief + pad printed in aluminium grey RAL 9006.
- Panels 1.2 mm thick sheet steel + paint finish
- Single door and panels bolt charcoal grey RAL 7016 polyamide
- 19" uprights 1.5 mm thick galvanised steel.
Number of U marked using black inkjet marking.
- Levelling feet zinc-plated steel with black polypropylene fixed base
3. TECHNICAL FEATURES (continued)
3.6 Electrical continuity of the conductive parts
Continuity of the metal conductive parts of the cabinet is achieved
by construction. For the panels, a stainless steel clip automatically
provides the equipotential link by pressing against the lower end plate
with galvanised steel finish.
3.7 Weight
Net weight excluding packaging.
Cabinet catalogue number Weight (kg)
0 463 00 69
0 463 06 77
0 463 12 84
0 463 18 (extension 0 463 30) 99 (72)
0 463 19 110
0 463 21/41 114
0 463 22/42 (extension 0 463 33) 127 (90)
0 463 23/43 151
0 463 28 138
0 463 29 163
Note: 19" LCS2 cabinets are delivered on a 125 mm high pallet.
3.4 Corrosion resistance
- Corrosion class of the environment:
C2 according to EN ISO 12944-2,
3K3 according to IEC EN 60721-3-3
- Salt spray test according to ISO 9227 (NSS test) and
IEC EN 60068-2-11 (test Ka) for 168 hours:
degree of rusting Ri1 according to ISO 4628-3,
propagation 1 mm according to ISO 4628-8
- Sulphur dioxide (SO2) test according to EN ISO 6988 for 48 hours:
degree of rusting Ri1 according to ISO 4628-3,
ISO 10289 annex A class 8 type image
3.5 Properties of the paint coating
- Thermosetting polyester paint applied by electrostatic dusting
- Charcoal grey RAL 7016
- Textured satin appearance
- 60 to 80 m thick
- Excellent impact and scratch resistance
- Excellent resistance to cleaning agents (excluding strong chlorinated,
fluorinated and ketone solvents).
Some products may change the appearance. It is therefore advisable
to carry out a test first.
- Light exposure test (xenon-arc lamp) according to
ISO 4892-2 method B for 500 hours: no visible fading
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
4/31
19" LCS2 freestanding cabinets
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
4. DIMENSIONS
All dimensions are in mm.
4.1 Dimensions
Model shown: 600 x 600 mm cabinet / 800 x 800 mm double door cabinet
Overall D
W
H1
FRONT VIEW
D W
REAR VIEWSIDE VIEW
A
4. DIMENSIONS (suite)
4.1 Dimensions (suite)
Single front door cabinets
Cat. No. Capacity W D
0 463 00
0 463 06
0 463 12
0 463 18
0 463 19
0 463 21
0 463 22
0 463 23
0 463 28
0 463 29
Extension cabinets
H2
0 463 30
0 463 33
Double front door cabinets
Cat. No. Capacity W D
0 463 41
0 463 42
0 463 43
24U 600 600 1226 1241/1271 610 659 1138 1208
29U 600 600 1448 1463/1493 610 659 1138 1208
33U 600 600 1626 1641/1671 610 659 1138 1208
42U 600 600 2026 2041/2071 610 659 1138 1208
42U 600 800 2026 2041/2071 610 859 1138 1408
42U 800 600 2026 2041/2071 810 657 1525 1408
42U 800 800 2026 2041/2071 810 857 1525 1608
42U 800 1000 2026 2041/2071 810 1057 1525 1808
47U 800 800 2248 2263/2293 810 857 1525 1608
47U 800 1000 2248 2263/2293 810 1057 1525 1808
42U 600 600 2026 2041/2071 600 659 1138 1208
42U 800 800 2026 2041/2071 800 857 1525 1608
42U 800 600 2026 2041 / 2071 810 657 1165 815 1535
42U 800 800 2026 2041 / 2071 810 857 1165 1015 1535
42U 800 1000 2026 2041 / 2071 810 1057 1165 1215 1535
Overall dimensions
(1)
H1 H2 min./max. W D A B
(1)
H1 H2 min / max W D A B C
(2)
Overall dimensions
(2)
VIEW FROM ABOVE
C
A
VIEW FROM ABOVE
160°
160°160°
B
B
(1)
Without level adjustment feet
(2)
With level adjustment feet (+15 to 45 mm)
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
5/31
19" LCS2 freestanding cabinets
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
4. DIMENSIONS (continued)
4.2 Usable dimensions
4.2.1 600 mm wide freestanding cabinets
600 mm wide cabinets are available in 4 heights:
24U, 29U, 33U and 42U
600
Usable space 450
4. DIMENSIONS (continued)
4.2 Usable dimensions (continued)
4.2.1 600 mm wide freestanding cabinets (continued)
600 mm wide cabinets are available in 2 depths: 600 and 800 mm
Model shown: 600 x 600 mm cabinet
659 / 859
600 / 800
7070
Continuous
adjustment with
markings at 12.5 mm
intervals
(6 x 12.5 mm)
425 max / 625 max
Capacity 24U/29U/33U/42U
Usable space 1086/1308/1486/1886
Fixing centre 1038/1260/1438/1838
Capacity 24U/29U/33U/42U
Usable space 996/1218/1396/1796
AA
115 115
Fixing centre
391 max./591 max.
Fixing centre
337 max./537 max.
Oblongs
7 x 50
Usable space 490
FRONT VIEW (without door)
Usable space 490/690
SIDE VIEW
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
6/31
19" LCS2 freestanding cabinets
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
4. DIMENSIONS (continued)
4.2 Usable dimensions (continued)
4.2.1 600 mm wide freestanding cabinets (continued)
600
41
(2)(1) (2)
425 max./625 max.
465
118 (193 max.) 87 (162 max.)
Usable space 450
Fixing centre 465 (19")
600/800
487/687
4. DIMENSIONS (continued)
4.2 Usable dimensions (continued)
4.2.2 800 mm wide freestanding cabinets
800 mm wide cabinets are available in 2 heights:
42U and 47U
800
7070
Usable space 450
600
451
(3)
(with door)
A-A CROSS-SECTION VIEW
(1)
Dimension below door at 19" uprights
(2)
Continuous adjustment with markings at 12.5 mm intervals
(3)
See front view on page 6
75
79
213
346
9.5 x 9.5
Capacity 42U/47U
Usable space 1886/2018
9096/296 133133
AA
600/800
VIEW FROM ABOVE
88
Usable space 690
Note: The dimensions of the upper and lower end plates are identical.
FRONT VIEW (without door)
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
7/31
19" LCS2 freestanding cabinets
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
4. DIMENSIONS (continued)
4.2 Usable dimensions (continued)
4.2.2 800 mm wide freestanding cabinets (continued)
800 mm wide cabinets are available in 3 depths: 600, 800 and
1000 mm
Model shown: 800 x 800 mm single door cabinet
657/857/1057
600/800/1000
Continuous
adjustment of the
four 19" uprights
with markings at
12.5 mm intervals
(6 x 12.5 mm)
425 max./625 max./825 max.
4. DIMENSIONS (continued)
4.2 Usable dimensions (continued)
4.2.2 800 mm wide freestanding cabinets (continued)
Model shown: 800 x 800 mm single door cabinet
800
141
(2)(1) (2)
425 max./625 max./825 max.
122 (197 max.) 87 (162 max.)
Usable space 97
Fixing centre 465 (19")
9.5 x 9.5
465
487/687/887
BB
600/800/1000
Capacity 42U/47U
Usable space 1796/2018
115 115
Fixing centre 1838/2060
Fixing centre
391 max./591 max./791 max.
Fixing centre
337 max./537 max./737 max.
Oblongs
7 x 50
Usable space 450
Fixing centre 465 (19")
800
(3)
(with door)
A-A CROSS-SECTION VIEW
(1)
Dimension below door at 19" uprights
(2)
Continuous adjustment with markings at 12.5 mm intervals
(3)
See front view page 7
Usable space 67
Fixing centre 465 (19")
Usable space 97
141
B-B CROSS-SECTION
Usable space 490/690/890
800 mm wide 19" LCS2 cabinets enable 19" equipment to be fixed
horizontally in the upper and lower parts.
SIDE VIEW
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
8/31
19" LCS2 freestanding cabinets
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
4. DIMENSIONS (continued)
4.2 Usable dimensions (continued)
4.2.2 800 mm wide freestanding cabinets (continued)
800
175
41
90 451
75/104/104
451
9.5 x 9.5
79
213
90
133133
96/296/496
4. DIMENSIONS (continued)
4.3 Positioning of supports on the floor
The cabinets are equipped with 4 levelling feet.
Accessories can be used to modify the link with the floor
(see sections 10.1 to 10.3).
600/800
346
600/800/1000
100 100
47
507/707/907
Ø 38 feet
400/600
600/800/1000
VIEW FROM ABOVE
Note: The dimensions of the upper and lower end plates are identical.
4.2.3 19" uprights
52
23,8
23,5
44,45
15,8715,87
44,45
47U / 42U / 33U / 29U / 24U
9,5
2092 / 1870 / 1470 / 1292 / 1070
7,5
1,5
32
52
15,87 15,87
44,45
23,8
8,25
44,45
44,45
9,5
31,25
17
4644,4544,45
16
8,5
2510,5
Ø 9
16
VIEW FROM BELOW
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
9/31
19" LCS2 freestanding cabinets
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
5. BAYING
5.1 Direct baying
19" LCS2 freestanding cabinets can be joined laterally together using
a baying kit:
Cat. No. For cabinets depth (mm)
0 463 37 600
0 463 38 800
0 463 39 1000
Note: The LCS2 range includes extension cabinets (single door) for
the 42U x 600 x 600 and 42U x 800 x 800 sizes. These special
cabinets are supplied with the baying kit and without side
panels.
A baying kit comprises:
- 2 galvanised steel lugs
- 2 steel crosspieces + paint finish (same as cabinets)
- Fixing screws
5. BAYING (continued)
5.2 Baying via cabling unit
5.2.1 Presentation
The LCS2 cabling unit is used to join laterally two 42U 19" LCS2
freestanding cabinets together, and provides easier management of
cables and patch cords.
Joined to 2 x 600 mm wide cabinets, the cabling unit is an
alternative solution to an assembly of 2 x 800 mm wide cabinets
and has smaller dimensions.
The cabling unit is available in 2 depths:
Cat. No. For 42U cabinets depth (mm)
0 463 34 600
0 463 35 800
Note: The LCS2 range includes extension cabinets (single door) for
the 42U x 600 x 600 and 42U x 800 x 800 sizes. These special
cabinets are supplied without side panels.
A cabling unit principally comprises:
- 2 identical end plates
- 2 identical doors
The crosspieces provide protection against dust and maintain the IP20
protection of the cabinets.
1600 (1610 overall)
800 800
VIEW OF A COMBINATION FROM ABOVE
The cabling unit can only be installed between 2 cabinets.
It cannot be mounted at the end.
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
10/31
19" LCS2 freestanding cabinets
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
5. BAYING (continued)
5.2 Baying via cabling unit (continued)
5.2.1 Presentation (continued)
Each door is reversible and easy to remove.
The end plates have cut-outs for cable entries.
The installation of a side cable tray optimises cable management (see
section 7.2).
5. BAYING (continued)
5.2 Baying via cabling unit (continued)
5.2.2 Features (continued)
Combination shown with two 600 x 600 mm cabinets.
250
2026
The cabling units are the same colour as 19" LCS2 cabinets, enabling
attractive assemblies to be created.
5.2.2 Features
- IK08
- IP20 maintained when joined
- Doors with handle equipped with a 2433A key lock (same as single
door cabinets)
- End plates 1.5 mm thick galvanised steel + paint finish (same as
cabinets)
- Doors 1.2 mm thick sheet steel + paint finish
(same as cabinets)
- Supplied with earthing kit and complete set of screws
- Feet zinc-plated steel with black polypropylene fixed base
FRONT VIEW
W
5252
REAR VIEW
Type of baying W Overall W
With 2 cab. width 600 1450 1460
With 1 cab. width 600 & 1 cab. width 800 1650 1660
With 2 cab. width 800 1850 1860
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
11/31
19" LCS2 freestanding cabinets
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
5. BAYING (continued)
5.2 Baying via cabling unit (continued)
5.2.2 Features (continued)
21
600/800
675/875 overall
VIEW FROM ABOVE
202
65
120
600/800
610/810
180/280
250
293
100
40
6. PLINTHS
6.1 Freestanding cabinet plinths
6.1.1 Presentation
19" LCS2 cabinets can be equipped with a 100 or 200 mm high metal
plinth.
310
LCS2 plinths comprise 4 one-piece corner blocks and 4 traps, height
100 mm, providing total accessibility on all 4 sides.
The plinths are the same colour as the cabinets so that they match
perfectly (charcoal grey RAL 7016).
A plinth is fixed directly to the end plate of the cabinet:
600/800
(1)
Usable height: 1922 mm
DETAILED VIEW FROM ABOVE
288
570/770
160/260
Usable space 250
INTERNAL CROSS-SECTION VIEW
(1)
Note: It is also possible to place 2 x 100 mm high plinths one on top of
the other.
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
12/31
19" LCS2 freestanding cabinets
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
6. PLINTHS (continued)
6.1 Freestanding cabinet plinths (continued)
6.1.1 Presentation (continued)
The following is required to create a plinth:
- The correct plinth kit for the width of the cabinet (corner blocks +
solid front and rear traps)
- The correct set of 2 solid side traps for the depth of the cabinet
(2 sets for a 200 mm high plinth)
D
Plinth kit (mm)
H = 100 W = 600
W = 800
H = 200 W = 600
W = 800
Cat. No.
0 464 50
Cat. No.
0 464 51
Cat. No.
0 464 52
Cat. No.
0 464 53
H
Set of 2 solid side traps (mm)
H = 100 D = 600
D = 800
D = 1000
H = 200 D = 600
D = 800
D = 1000
Cat. No. 0 464 54
Cat. No. 0 464 56
Cat. No. 0 464 58
2 x Cat. No. 0 464 54
2 x Cat. No. 0 464 56
2 x Cat. No. 0 464 58
W
6. PLINTHS (continued)
6.1 Freestanding cabinet plinths (continued)
6.1.1 Presentation (continued)
If cabinets are joined together directly, their plinths can be joined
together mechanically (screws not supplied).
The solid traps can be replaced by:
- Either a ventilated trap for natural ventilation
- Or a trap with brushes for cable entry on one side of the plinth
These special traps, also 100 mm high, are supplied singly.
D
W/D = 600
W/D = 800
W
Ventilated trap Trap with brushes
Cat. No. 0 464 60 Cat. No. 0 464 62
Cat. No. 0 464 61 Cat. No. 0 464 63
The plinths can be equipped with cross bars. Fixed between 2 corner
blocks, they can be used for clamping cables and, in a 200 mm high
plinth, for fixing a U-shaped cable tray.
0 476 93/94/95
Cross bars
Cat. No. For depth (mm)
0 476 93
0 476 94
0 476 95
600
800
1000
U-shaped cable trays
Cat. No. Internal width x height (mm)
0 464 69
0 464 70
200 x 54
400 x 54
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
13/31
19" LCS2 freestanding cabinets
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
6. PLINTHS (continued)
6.1 Freestanding cabinet plinths (continued)
6.1.2 Features
6.1.2.1 Cabinet plinths (plinth kit + side traps)
- Plinth fixed using M12 screws
- Traps fixed using black zinc-plated M6 screws
- Corner blocks 2 mm thick steel + paint finish (same as cabinets)
- Traps 1.5 mm thick steel + paint finish (same as cabinets) with
double fold reinforcement on floor side
- Supplied with complete set of screws for the equipotential link with
the cabinet
- Can be fixed to the floor (screws not supplied)
14
100
or
200
W
A
A
14
D
B
C
D
B
6. PLINTHS (continued)
6.1 Freestanding cabinet plinths (continued)
6.1.2 Features (continued)
6.1.2.3 Cross bars
- 2 mm thick galvanised steel
- Supplied singly with fixing screws
A
B
25
12.5
Ø 4.5
Ø 8.5
25
9
16
Dimensions (mm)
Overall Fixings Usable area
W x D W D A B C D
600 x 600 599 599 478 478 449 449
600 x 800 599 799 478 678 449 649
800 x 600 799 599 678 478 649 449
800 x 800 799 799 678 678 649 649
800 x 1000 799 999 678 878 649 849
6.1.2.2 Ventilated traps/with brushes
- Height 100 mm
- Steel thick 1.5 mm + paint finish (same as cabinets) with double fold
reinforcement on floor side
- Supplied with black zinc-plated M6 fixing screws
The ventilated traps have Ø 5 mm perforations:
Cat. No.
0 476 93 444 375
0 476 94 644 575
0 476 95 844 775
6.1.2.4 U-shaped cable trays
- Length 3 m
- Frame 100 x 50 mm
- Zinc-plated steel
- Supplied with screws for fixing on the cross bars
Cat. No. Overall dimensions (mm) Wire diameter (mm)
0 464 69 218 x 64 4.4
0 464 70 424 x 64 3.9 and 5.9
A B
The traps with brushes are supplied with a black stiff brush and a
black flexible brush (polyamide fibres).
The usable feedthrough area of the cable entry with brushes is:
- 424 x 45 mm for width/depth 600 mm
- 624 x 45 mm for width/depth 800 mm
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
14/31
19" LCS2 freestanding cabinets
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
6. PLINTHS (continued)
6.2 Plinth for cabling unit
When joining 19" LCS2 freestanding cabinets via a cabling unit,
Cat. No. 0 464 64 is used to link the plinths of the joined cabinets (at
the front and/or rear).
Cat. No. 0 464 64 comprises a 100 mm high trap.
For a height of 200 mm, the number of traps must be doubled.
100
Cat. No. 0 464 64
6. PLINTHS (continued)
6.3 Linking interface (continued)
6.3.1 Presentation (continued)
The linking interface helps to maintain the bending radius of the
cables:
U-shaped cable tray, see section 6.1.
200
Cat. No.
0 464 64 x 2
The trap is made of 1.5 mm thick steel with paint finish (same as
cabinets) and supplied with its fixing screws.
6.3 Linking interface
6.3.1 Presentation
The linking interface Cat. No. 0 464 66 provides protection and a
finish for the link between freestanding cabinets and cable ducts. It is
positioned to the right or left of a 600 mm deep cabinet equipped with
a 200 mm high plinth.
It is mechanically joined to the cabinet plinth.
The interface comprises:
- 3 corner blocks
- A front panel trap
- A cover
Its reversible cover with cut-outs allows for different cable entry
configurations.
6.3.2 Features
- Corner blocks and cover 2 mm thick steel + paint finish
(same as cabinets)
- Trap 1.5 mm thick steel + paint finish (same as cabinets)
- Supplied with black cable entry brushes (polyamide fibres)
and complete set of screws (apart from those for fixing to the floor)
120
600
(1)
Usable feedthrough area with brush: 110 x 435 mm
75
435
435
(1)
120
600
(1)
160
200
Fixing to the floor
14
478
478
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
15/31
19" LCS2 freestanding cabinets
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
6. PLINTHS (continued)
6.4 Adjustable height plinths
6.4.1 Presentation
Adjustable height plinths are used in rooms equipped with a raised
floor composed of tiles. The plinth transfers the load of the cabinet
directly to the ground.
Adjustable height plinth
Cat. No. For cabinet width / depth (mm)
0 464 30 600 x 600
0 464 31 600 x 800
0 464 32 600 x 1000
0 464 34 800 x 600
0 464 35 800 x 800
0 464 36 800 x 1000
Each plinth is supplied with front and rear floor tile support brackets.
Side tile support brackets must be order separately for the end of the
cabinets:
Set of 2 side tile support brackets
Cat. No. For plinth depth (mm)
0 464 38 600
0 464 39 800
0 464 40 1000
6. PLINTHS (continued)
6.4 Adjustable height plinths (continued)
6.4.2 Features
- For floor tiles 30 or 38 mm thick
- Height adjustable from 200 to 350 mm in 25 mm steps + fine
adjustement by levelling feet
- Permissible load: 1 000 kg
- Direct fixing to the end plate of the cabinet by M12 screws
- Can be fixed to the floor (screws not supplied)
- Plinth 2 mm thick galvanised steel
- Tile support brackets 1.5 mm thick galvanised steel
- Levelling feet zinc-plated steel with block polypropylene fixed base
- Supplied with complete set of screws for the equipotential link with
the cabinet
Depth
14
C
25
support
Set of
2 lateral
tile support
brackets
Cat. Nos
0 464 38/
39/40
Width
B
Ø9
D
H
thickness)
30
or 38
(tile
A
15
31
(tile
area)
Cat. No. Width x
0 464 30
0 464 31
0 464 32
0 464 34
0 464 35
0 464 36
(1)
Ajustable in 25 mm steps + fine adjustement
Depth
600 x 600
600 x 800 730 635 478 x 678 520 x 720
600 x 1000 930 835 478 x 878 520 x 920
800 x 600
800 x 800 730 635 678 x 678 720 x 720
800 x 1000 930 835 678 x 878 720 x 920
(1)
H
Min. Max. A B C D With
200 350
Usable area Distance
530
730
530
530
(width x depth)
cabinet
435 478 x 478 520 x 520
435
435 678 x 478 720 x 520
635
To the
ground
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
16/31
19" LCS2 freestanding cabinets
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
7. CABLE MANAGEMENT
7.1 Cable entry plates
7.1.1 Presentation
19" LCS2 freestanding cabinets have pre-cut 19" format top and
bottom cable entries.
800
600
7. CABLE MANAGEMENT (continued)
7.1 Cable entry plates (continued)
7.1.1 Presentation (continued)
The metal plates are equipped with 2 quick fixings that do not require
any screws or tools.
At the top of LCS2 cabinets, the metal plates must be fixed
using screws and cage nuts with pins in order to provide
the equipotential link between the plate and the painted end
plate of the cabinet.
1
Cat. No. 0 364 54
2
After cutting out the cable entries, they can be equipped with
feedthroughs with brushes using the following 19" equipment:
Cat. No. Plate with brushes
0 465 28 Plastic 1U
0 465 29 Plastic 2U
0 465 30 Metal 1U
0 465 31 Metal 2U
The plastic plates Cat. Nos. 0 465 28/29 clip directly onto the cable
entries. They require a flat screwdriver for removal.
CLICK
The 3U cable entries also enable the installation of plates with fans
Cat. Nos. 0 464 87/88 for thermal management of the cabinet (see
section 9.1).
7.1.2 Features
7.1.2.1 Plastic plates
ABS plates equipped with a flexible brush (2 brushes for 2U height).
Black RAL 9005
1U plate Cat. No. 0 465 28 (above):
- 2 feedthroughs 125 x 25 mm
- 1 central feedthrough 113 x 25 mm
2U plate Cat. No. 0 465 29:
- 2 feedthroughs 125 x 45 mm
- 1 central feedthrough 113 x 45 mm
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
17/31
19" LCS2 freestanding cabinets
P
L
P
L
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
7. CABLE MANAGEMENT (continued)
7.1 Cable entry plates (continued)
7.1.2 Features (continued)
7.1.2.2 Metal plates
Plates 1.5 mm thick steel equipped with a flexible brush
(2 brushes for 2U height).
Black RAL 9005.
1U plate Cat. No. 0 465 30:
- 1 feedthrough 400 x 23 mm
2U plate Cat. No. 0 465 31 (above):
- 1 feedthrough 400 x 66 mm
7.2 Cable trays
7.2.1 Presentation
With the cable management supports, a side and/or rear cable tray
can be installed in 19" LCS2 freestanding cabinets.
The advantage of the flat cable tray over the U-shaped tray is that the
cables flow more easily (no edges).
7. CABLE MANAGEMENT (continued)
7.2 Cable trays (continued)
7.2.1 Presentation (continued)
The supports are fixed onto the structural uprights of the cabinet, and
the tray is mounted without screws:
1
2
P
Cat. No. Set of 3 supports
0 464 72 For cabinet width/depth 600 mm
0 464 73 For cabinet width/depth 800 mm
0 464 74 For cabinet depth 1000 mm
Cat. No. Flat cable trays
0 464 76 For 33U cabinet
0 464 77 For 42U cabinet
42U 19" LCS2 cabinets can also be joined via a cabling unit,
providing a solution for easy management of cables and cords (see
section 5.2).
7.2.2 Features
7.2.2.1 Cable management supports
- Supplied in sets of 3
- For fixing using self-tapping screws
- Max. diameter of grid wire: 6 mm
- 1.5 mm thick galvanised steel
W
L
6.5 x 11.5
9.5 x 9.5
50
Cat. No. W (mm) No. of tray fixing points Fixing centre
0 464 72 450 9 510
0 464 73 650 13 710
0 464 74 850 17 910
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
18/31
19" LCS2 freestanding cabinets
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
7. CABLE MANAGEMENT (continued)
7.2 Cable trays (continued)
7.2.2 Features (continued)
7.2.2.2 Flat cable trays
- Frame: 100 x 50 mm
- Zinc-plated steel
Cat. No. Overall dimensions (mm) Wire diameter
(mm)
0 464 76 1405 x 255 4.4
0 464 77 1805 x 255 4.4
7.3 Vertical cable management grid
7.3.1 Presentation
800 mm wide 42U 19" LCS2 freestanding cabinets can take the
vertical cable management grid Cat. No. 0 331 35, fixed onto the
outside of the 19" uprights.
The guide has articulated latches. As the latches are clipped on, their
direction of opening can be reversed.
7. CABLE MANAGEMENT (continued)
7.4 Vertical cable manager
7.4.1 Presentation
800 mm wide 42U 19" LCS2 42U freestanding cabinets can be fitted
with the set of 2 vertical cable manager panels Cat. No. 0 464 80.
The panels are mounted on the outside of the 19" uprights. The wiring
is organised using feedthroughs with brushes, cable management
rings and slots for cable ties.
42U 19" LCS2 cabinets can also be joined via a cabling unit,
providing a solution for easy management of cables and cords (see
section 5.2).
7.3.2 Features
- Supplied singly
- Overall dimensions: H 1562 x W 100 X D 155 mm
- Wire diameter: 5 mm
- Steel wire + paint, ABS-PC latches
- Supplied with screws
- Black RAL 9005
The management rings are plastic and radiate out to provide optimum
protection for cords (maintain the bending radius). Each ring clips on
horizontally or vertically:
CLICK
42U 19" LCS2 cabinets can also be joined via a cabling unit,
providing a solution for easy management of cables and cords (see
section 5.2).
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
19/31
19" LCS2 freestanding cabinets
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
7. CABLE MANAGEMENT (continued)
7.4 Vertical cable manager (continued)
7.4.2 Features
- Set of 2 panels
- For fixing on 19" uprights and framework
- Ability to adjust the depth of the 19" uprights retained
- Feedthroughs: 174 x 50 mm usable
- Supplied with 8 flexible brushes and 8 stiff brushes (black polyamide
fibres)
- Supplied with 10 cable management rings, usable cross-section
4070 mm2 (Cat. No. 0 465 42)
- Supplied with 9 cable ties with tightening indicator:
3 x Cat. No. 0 331 94,
3 x Cat. No. 0 331 95 and 3 x Cat. No. 0 331 96
- Supplied with screws
- Overall panel dimensions: 1878 x 108 mm
- Panels 1.5 mm thick steel
- Polyamide rings
- Black RAL 9005
7.5 Cable ties
7.5.1 Cable ties with tightening indicator
Cable ties with tightening indicator are wide ties with a smooth inner
surface for optimum protection of cables. They incorporate a warning
system to prevent over-tightening: fusible crescent-shaped pins snap
one after the other and act as visual and audible indicators.
8. VERTICAL EXTENSION
The set of 2 vertical extension uprights Cat. No. 0 464 81 increases
the capacity of 42U 800 mm wide 19" LCS2 freestanding cabinets by
12 U, giving a total capacity of 54U.
0 464 81
42U
800
Hooks hold the excess strap in place.
The ties are released by pinching the head of the tie and can be reused.
Cat. No. Width (mm) Length (mm)
0 331 94 15 180 35 15
0 331 95 15 225 50 35
0 331 96 15 320 80 50
- Tensile strength: > 100 N
- Fire resistance: UL 94 HB
- Black high impact PBT
7.5.2 Self-locking cable ties
Self-locking cable ties are repositionable textile ties that do not
damage cables.
Cat. No. Colour Width (mm) Length (mm)
0 331 84 Black 16 150 35
0 331 85 Red 16 150 35
0 331 86 Green 16 150 35
0 331 87 Black 16 300 80
0 331 88 Red 16 300 80
0 331 89 Green 16 300 80
- Tensile strength: > 220 N
- Fire resistance: UL 94 V2
- Double-sided textile with "loops" on one side and "hooks" on the other
Tightening Ø (mm)
Max. Min.
Max. tighte-
ning Ø (mm)
x 2
The extension, mounted on either side of 19" uprights, has 6 x 2U
positions for mounting 19" equipment vertically (panels, 19" PDUs,
etc.).
The cable management rings are plastic and radiate out to provide
optimum protection for cords (maintain the bending radius). Each ring
clips on horizontally or vertically:
Features
- Set of 2 uprights
-
For fixing on 19" uprights and
- Ability to adjust the depth of the 19" uprights retained
- Positions for 19" equipment: usable area 450 x 90 mm, perforations
9.5 x 9.5 mm
- Supplied with 8 cable management rings, usable cross-section
4070 mm2 (Cat. No. 0 465 42)
- Supplied with screws
- Overall dimensions of upright: 1878 x 108 mm
- Uprights 1.5 mm thick steel
- Polyamide rings
- Black RAL 9005
framework
(top, bottom and central)
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
20/31
19" LCS2 freestanding cabinets
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
9. THERMAL MANAGEMENT
9.1 Plates with fans
19" LCS2 freestanding cabinets can take plates with fans at the 3U
cable entries. Installed in the top of the cabinet, the plates provide a
high extraction rate.
Cat. No. No. of fans Output (m3/h)
0 464 87 2 180
0 464 88 3 270
Features
- IP XXB - IK08
- 230 V~ - 50/60 Hz power supply
Cat. No. Current (A) Power (W)
0 464 87 0.25 36
0 464 88 0.37 54
- Equipped with 3 x 0.75 mm2 flexible power supply cable,
length 2.5 m
- Fixed using M6 screws and cage nuts with pins (supplied)
- Plate steel + paint finish (same as cabinets)
- Charcoal grey RAL 7016
133 (3U)
89
60
482
465 (19
200
)
"
9. THERMAL MANAGEMENT (continued)
9.2 1U ventilation drawers
The ventilation drawers are 19" equipment which provide circulation
of the internal air. They provide targeted heat removal and ensure
uniformity of the temperature in the cabinet.
Cat. No. No. of fans Depth (mm)
0 464 89 2 150
0 464 90 4 300
Each fan provides an output of 90 m3/h.
The arrows below indicate the ventilation direction in the operating
position:
Features
- IP XXB - IK08
- 230 V~ - 50/60 Hz power supply per IEC 60320 C14 socket
Cat. No. Current (A) Power (W)
0 464 89 0.25 36
0 464 90 0.5 72
60
45
45
482
465 (19
324
133 (3U)
)
"
162
89
- Supplied with C13 cord - French/German standard plug, length 1.2 m
- Illuminated ON/OFF switch
- For fixing on 2 x 19" uprights using M6 captive screws and 9.5 mm
cage nuts with pins (supplied)
- Weight: 3 kg (Cat. No. 0 464 89)
5.3 kg (Cat. No. 0 464 90)
- Drawer steel
- Black RAL 9005
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
21/31
19" LCS2 freestanding cabinets
P 600
P 800
P 1000
P 600/800/1000
P 600
P 800
P 1000
P 600/800/1000
P 600
P 800
P 600/800
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
9. THERMAL MANAGEMENT (continued)
9.2 1U ventilation drawers (continued)
150
(1)
442
75
200
60
43
1U
(53 overall)
442
200
60
43
(53 overall)
(1)
Overall dimensions: +70 mm for back connection
9.3 Thermostat
The mechanical thermostat Cat. No. 0 348 48 is used to control the
switching on/off of the fans in order to control the temperature inside
the cabinets.
1U
Fans Thermostat Cat. No. 0 348 48
19
"
300
(1)
150
75
"
19
10. ACCESSORIES
10.1 Anti-tilt kit
The anti-tilt kit Cat. No. 0 464 84 stabilises a 19" LCS2 freestanding
cabinet (which is not fixed to the floor) when heavy products installed
on telescopic equipment are removed.
The kit, which consists of 2 rails fixed under the lower end plate,
prevents the cabinet tilting forwards.
The kit can be mounted before or after installation of the cabinet.
The kit is suitable for all three cabinet depths:
P 600/800/1000
P 600
P 800
P 1000
Features
- IP20
- 230 V~ - 50/60 Hz
- Adjustment range +5°C to +60°C
- Switching range: 2°C
- NC contact: 5 A, 250 V~
- NO contact: 10 A, 250 V~
- Connection via 2.5 mm2 terminal block
- Class N interfercab. suppression according to VDE 0875
- Magnetic mounting
- Black
51
68
To limit the projection of the rails at the front of the cabinet, another
type of mounting is possible for cabinets depth 600/800 mm:
P 600/800
P 600
P 800
It is essential not to exceed the following dual limit:
- 100 kg total weight installed on runners
- 570 mm projection
570
++
+…=
100 Kg max.
37
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
22/31
19" LCS2 freestanding cabinets
P 600
P 800
P 1000
P 600/800/1000
P 600
P 800
P 600/800
570
++
100 Kg max.
+…=
A
B
Ø 10 mm max
A
B
Ø 10 mm max
A
B
Ø 10 mm max
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
10. ACCESSORIES (continued)
10.1 Anti-tilt kit (continued)
Features
C-section, length 1400 mm.
Steel + paint finish (same as cabinets)
Supplied with fixing screws
Charcoal grey RAL 7016
40
10.2 Floor fixing kit
Fixing kit Cat. No. 0 464 86 is used to fix a 19" LCS2 freestanding
cabinet to the floor permanently. The 4 lugs in the kit, when screwed
to the floor, lock the levelling feet of the cabinet.
12 12
2.5
60
10. ACCESSORIES (continued)
10.2 Floor fixing kit (continued)
The kit is used for remote fixing outside the cabinet.
Features
Set of 4 galvanised steel lugs (without screws).
100 30
Ø 11 Ø 11
200
10.5
14
40
2.5
Ø 10 mm max
B
10.3 Casters
19" LCS2 freestanding cabinets can be equipped with a set of 4
pivoting casters Cat. No. 0 464 83.
The total load on the 4 casters must not exceed 380 kg.
Features
- Set of 4 casters with fixing screws
- Raise cabinet by 70 mm
- Wheels black polyamide
54 35
12 27
32 30
70
A
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
Ø 50
23/31
19" LCS2 freestanding cabinets
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
10. ACCESSORIES (continued)
10.4 19" lighting kit
The kit Cat. No. 0 464 85 consists of a 1U 19" panel equipped with a
fluorescent light.
Features
- Quick screw-free fixing on 2 x 19" uprights
- Class I
- IP20
- ON/OFF switch
- 230 V~ - 50Hz power supply
- Ferromagnetic ballast
- Rear connection on terminal block
- For Ø 16 mm fluorescent tube, length 288 mm, G13 cap
- Supplied with 8 W white tube
- Panel 1.5 mm thick steel + black RAL 9005 finish
11. 19" EQUIPMENT
11.1 19" management panels
For ease of mounting, the 19" LCS2 panels incorporate a quick fixing:
- The plastic panels clip on directly. The only tool required is a flat
screwdriver for their removal (see section 7.1).
- The metal panels are equipped with 2 ergonomic fixings that do not
require any screws or tools.
11. 19" EQUIPMENT (continued)
11.1 19" management panels (continued)
11.1.1 Management panels with 2 axes
- Metal panels with quick fixing
- Horizontal and front to back feedthrough
- Plastic cable management rings radiating out (to protect cords and
maintain the bending radius)
Cat. No.
0 465 22
0 465 23
- Excellent resistance to unclipping under the weight of cables and
cords
Panels
with
2 axes
Metal 1U 90 30 x 60 1890
Metal 2U 90 65 x 60 4070
Depth
(mm)
Dimensions of
feedthroughs
(mm)
Rings usable
cross-section
(mm2)
The quick fixing for metal panels is compatible with 1.4 to 2.75 mm
thick 19" uprights with 8.25 to 9.5 mm square perforations.
An automatic equipotential link is ensured with 19" LCS2 uprights.
Direct clipping on of plastic panels is compatible with 1.5 to 2 mm
thick 19" uprights with 9.5 mm square perforations.
10 kg
50 mm
- Panels 1.5 mm thick steel
- Polyamide rings
- Zamak quick fixing
- Black RAL 9005
11.1.2 Management panels with brushes
- Direct clip-on plastic panels
- Metal panels with quick fixing
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
24/31
19" LCS2 freestanding cabinets
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
11. 19" EQUIPMENT (continued)
11.1 19" management panels (continued)
11.1.2 Management panels with brushes (continued)
Cat. No. Panels with brushes Dimensions of brush
feedthrough (mm)
0 465 28 Plastic 1U Side: 125 x 25
Central: 113 x 25
0 465 29 Plastic 2U Side: 125 x 45
Central: 113 x 45
0 465 30 Metal 1U 400 x 23
0 465 31 Metal 2U 400 x 66
- Panels ABS or 1.5 mm thick steel
- Flexible brush (2 brushes for 2U height)
- Zamak quick fixing
- Black RAL 9005
These panels are also used to equip cabinet cable entries with
brush feedthroughs (see paragraph 7.1).
11. 19" EQUIPMENT (continued)
11.2 Fixed shelves
11.2.1 Projecting mounting fixed shelf
- For direct screw-free fixing on 2 x 19" uprights
- Shelf is perfored for a better internal ventilation,
and possibility of clamping using cable ties
Cat. No. Depth (mm) Usable width (mm)
0 465 00 115 435
0 465 01 200 435
0 465 02 360 435
- Height 2U
- Max. load: 15 kg
- Automatic earthing on 19" LCS2 uprights
- 50 x 7 mm oblong perforations
- 1.5 mm thick steel
- Black RAL 9005
Note: When mounted towards the front, projecting shelves can be
used as temporary work surfaces.
11.2.2 Fixed shelf for fixing on 4 x 19" uprights
- Quick screw-free fixing system
- For mounting on 4 x 19" uprights
- Fixing independent of the depth position of the 19" uprights
- Shelf is perfored for a better internal ventilation,
and possibility of clamping using cable ties
11.1.3 Blanking plates
- Direct clip-on plastic plates
- Metal plates with quick fixing
Cat. No. Blanking plates
0 465 32 Plastic 1U
0 465 33 Plastic 2U
0 465 38 Metal 1U
0 465 39 Metal 2U
0 465 40 Metal 3U
- Plates ABS or 1.5 mm thick steel
- Zamak quick fixing
- Black RAL 9005
1
2
3
Cat. No. For cab. depth
(mm)
0 465 05 600 425 440
0 465 06 800 625 440
0 465 07 1000 825 440
- Height 1U
- Max. load: 50 kg
- Automatic earthing
- 50 x 7 mm oblong perforations
- Shelf 1.5 mm thick steel
- Black RAL 9005
Depth (mm) Width (mm)
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
25/31
19" LCS2 freestanding cabinets
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
11. 19" EQUIPMENT (continued)
11.3 Telescopic shelves
- Quick screw-free fixing system
- For mounting on 4 x 19" uprights
- Easy adjustment to the depth position of the 19" uprights
- Shelf is perfored for a better internal ventilation, and possibility of
clamping using cable ties
- Locking in open position
Cat. No. For cab.
depth (mm)
0 465 08 600 425 425 320
0 465 09 800 625 425 420
0 465 10 1000 625 425 420
- Height 1U
- Max. load: 50 kg
- Automatic earthing
- 50 x 7 mm oblong perforations
- Shelf 1.5 mm thick steel
- Black RAL 9005
- Ball-bearing runners
In case of the risk of tilting when heavy items are removed,
the cabinet must be fixed to the floor or stabilised using an
anti-tilt kit (see sections 10.1 and 10.2).
11.4 Fixed shelf for heavy items
- For mounting on 4 x 19" uprights
- Front fixing via screws
- Adjustment in 12.5 mm intervals
to the depth position of the 19" uprights
Cat. No. For cab. depth
(mm)
0 465 17 1000 820 425
- Height 1U
- Max. load: 100 kg
- Supplied with screws and cage nuts with pins
- 50 x 7 mm oblong perforations (possibility of clamping using cable ties)
- 2 mm thick steel
- Black RAL 9005
11.5 Keyboard shelf
Shelf for computer screen.
Depth
(mm)
Depth
(mm)
Width
(mm)
Travel
(mm)
Width
(mm)
11. 19" EQUIPMENT (continued)
11.5 Keyboard shelf (continued)
With sliding shelf for mouse, integrated mat and position for mouse
250
- For mounting on 4 x 19" uprights
- Front fixing via screws
- Min. fixing centre: 625 mm
Cat. No. For cab.
depth (mm)
0 465 19
800
1000
- Height 1U (5U with vertical keyboard support)
- Max. load: 50 kg
- Supplied with screws and cage nuts with pins
- 1.5 mm thick steel
- Black RAL 9005
11.6 Set of 2 fixed sliders
- For fixing on 4 x 19" uprights
Cat. No. For cab. depth
(mm)
0 465 11 600 337 312 382 —
0 465 12 800 537 512 582 465
0 465 13 1000 737 712 782 654
- Max. load: 50 kg
- Supplied with screws
- 1.5 mm thick galvanised steel
Cat. No. 0 465 11 and 0 465 12
Ø 6.5
Ø 7
Depth
(mm)
625 420 500
(mm)B (mm)
460 max.
Shelf for screen
A
A
B
D
Width
(mm)
Usable
depth (mm)
C
(mm)
12.5
23.5
D
(mm)
22.5
12.5
19.5
With retractable
keyboard support
5U
Ø 15
Ø 7 Ø 7 (Cat. No. 0 465 12)
C
Profile and dimensions when in position in 19" LCS2 freestanding cabinets:
465 (width between 19" uprights)
462
441
18.5
394
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
23.5
12
10.5
26/31
69.5
69.5
19" LCS2 freestanding cabinets
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
11. 19" EQUIPMENT (continued)
11.6 Set of 2 fixed sliders (continued)
Cat. No. 0 465 13
Ø 6.5
Ø 7
Ø 15
Ø 7
Profile and dimensions when in position in 19" LCS2 freestanding cabinets:
465 (width between 19" uprights)
18.5
A
B
D
674
C
462
441
351
12.5
45
12.5
29
10.5
12. POWER DISTRIBUTION
12.1 Vertical PDUs
- Designed to provide 230 V~ power supply for active products
- For mounting in 42U/47U LCS2 freestanding cabinets with a PDU
22.5
support cat. No. 0 465 75/76 (see section 12.3)
- PDU fixing centre: 1697 mm min - 1703 mm max
19.5
69.5
12
69.5
Mounting with a PDU support
Cat. No. 0 465 75/76
- 2P+E sockets
- Protection of each circuit by circuit breaker
- Circuit breakers equipped with cover for protection against accidental
breaks
- Overall dimensions: H 1720 x W 55 x D 51 mm (88 mm overall depth
at the circuit breaker slot)
- Supplied with fixing screws
- Black aluminium body, plastic end pieces for fixing
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
27/31
19" LCS2 freestanding cabinets
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
12. POWER DISTRIBUTION (continued)
12.1 Vertical PDUs (continued)
12.1.1 Single phase PDU
PDUs comprising 2 circuits.The total number of sockets is distributed
equally between the 2 circuits.
Each circuit is identified by colour coding (white sockets and black
sockets).
Cat. No.
0 465 81 24 C13 IEC 60320
0 465 84
0 465 80 24 French - Belgian
0 465 88 24 German
0 465 89 22 British
(1)
Clamping capacity: Ø12 to Ø18 mm
Features
Cat. No.
2P+E sockets
Number Standard
4/6 mm2 terminal block
via cable gland
16 C13 IEC 60320
3x2.5 mm2 cord of 3 m
lenght with IEC 60309
6 C19 IEC 60320
2P+E plug 32A
4/6 mm2 terminal block
via cable gland
Power supply Use
Voltage Max. current Power
Connection
(1)
(1)
(1)
Protection
12. POWER DISTRIBUTION (continued)
12.1 Vertical PDUs (continued)
0 465 80 0 465 81 0 465 85 0 465 880 465 84 0 465 89
(1)
0 465 81
16A circuit
breaker
0 465 84
Single pole
+ neutral
0 465 80
0 465 88
0 465 89
(1)
Per circuit
230V - 250V
50/60 Hz
16A 3680 W
C type
16A circuit
breaker
Single pole
C type
12.1.2 Three-phase PDU
One circuit per phase composed of 8 C13 sockets + 1 C19 socket.
Cat. No.
0 465 85
2P+E sockets
Number Standard
24 C13 IEC 60320
3 C19 IEC 60320
Connection
5x4 mm2 cord of 3 m lenght
with IEC 60309 3P+N+E
plug 32A
Features
Cat. No.
Power supply Use
Voltage Max. current Power
(1)
Protection
16A circuit
breaker
Single pole
+ neutral
0 465 85
380V
50/60 Hz
32A 3680 W
C type
(1)
Per circuit/phase
(1)
Legrand also has a range of 19" PDU and vertical PDU with
intensity measure ability. To know all the features of these metered
PDU, consult the specific data sheet.
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
28/31
19" LCS2 freestanding cabinets
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
12. POWER DISTRIBUTION (continued)
12.2 19" PDUs
- Designed to provide 230 V~ power supply for active products
- For mounting on 19" fixing centre
- 180° reversible end pieces for 2 fixing options:
- 2P+E sockets
- Connection via 2.5 mm2 terminal block
- Overall dimensions: H 55 x W 483 x D 52 mm (Cat. No. 0 332 37,
88 mm overall depth at the circuit breaker slot)
- Provide a 2U space
- Supplied with screws and cage-nuts
- Black aluminium body, plastic end pieces for fixing
12.2.1 Socket PDU
Cat.
No.
0 465 51 12
0 465 52 9
0 465 50 9
0 465 54 6 —
0 332 88 6
0 332 37 6 Circuit breaker
0 332 87 6
0 465 60 9
0 465 62 6 —
0 332 38 6 Circuit breaker
0 465 65 6
6 339 00 5
2P+E sockets
Number Standard
C13 IEC
60320
C19 IEC
60320
French
-
Belgian
German
British
Additional
function
—
—
—
Switch with
indicator
Tamperproof for
uninterruptible
power supply
(UPS)
—
— Black
Colour
Black
Black
Alumin. grey
White sockets
Alumin. grey
Red sockets
Black
Alumin. grey
White sockets
Alumin. grey
White sockets
12. POWER DISTRIBUTION (continued)
12.2 19" PDUs (continued)
12.2.1 Socket PDU (continued)
Features
Cat. No.
0 465 51
0 465 52
0 465 50
0 465 54
0 332 88
0 332 37
0 332 87
0 465 62
0 332 38
0 465 65
6 339 00
12.2.2 PDU with surge protector
- Provides protection against mains overvoltages while keeping
sockets energised
- Replacement of protection with surge protector module
Cat. No. 0 775 41 (indication by red LED)
Cat.
No.
0 332 78 6
Power supply Use
Voltage Max. current Power Protection
10A 2500 W
16A circuit
breaker
230V - 250V
50/60 Hz
2P+E sockets
Number Standard
French
-
Belgian
16A 3680 W
13A 2990W —
Additional
function
Surge protector
Switch with
indicator
2 pole
C type
16A circuit
breaker
2 pole
C type
Colour
Alumin. grey
White
sockets
—
—0 465 60
Features
Power supply Use
Voltage Max. current Power Protection
230V - 250V
50/60 Hz
16A 3680 W —
Legrand also has a range of 19" PDU and vertical PDU with
intensity measure ability. To know all the features of these metered
PDU, consult the specific data sheet.
Cat. No.
0 332 78
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
29/31
19" LCS2 freestanding cabinets
1600 (0 465 75)
73
(71 intérieur)
20
31.2
27 x 7
74 x 980.5 x 5.5
105.5 x 5.5
70.5 x 5.5
29 x 9
94 x 9
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
12. POWER DISTRIBUTION (continued)
12.2 19" PDUs (continued)
12.2.3 PDU to be equipped
Cat. No. Capacity Colour
0 332 79 16 Mosaic modules Alumin. grey
12.3 PDU supports
- Vertical supports to be fixed at the side back of 42U/47U 19" LCS2
cabinets
- Make possible the mounting of the vertical PDU in 19" LCS2
cabinets (see section 12.1)
- Can receive 19" PDU vertically
- Many possibilities of fixing by screw. PDU with buttons can be fixed
by hanging all 7U
Cat. No. For cabinet capacity
0 465 75 42U
0 465 76 47U
- Supplied with fixing screws
- 1.5 mm thick galvanised steel
12. POWER DISTRIBUTION (continued)
12.3 PDU supports (continued)
(71 inside)
25
31.2
73 (71 inside)
73 (71 intérieur)
20
27 x 7
1822 ( 0 465 76)
800 (0 465 75)
911 (0 465 76)
105.5
1858 (0 465 75)
2080 (0 465 76)
1827 (0 465 75)
2049 (0 465 76)
1755 MAX (0 465 75)
105.5 x 5.5
70.5 x 5.5
1986 MAX ( 0 465 76)
ø 22
ø 12
74 x 980.5 x 5.5
29 x 9
94 x 9
5 x 7U ( 0 465 75)
6 x 7U ( 0 465 76)
(1)
7 U
(1)
(1)
(1)
For mounting PDU with buttons
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
30/31
19" LCS2 freestanding cabinets
12. POWER DISTRIBUTION (continued)
12.4 Multi-application DIN rail kit
- For mounting modular devices on 19" fixing centre (circuit breakers,
Legrand multimedia network components… etc)
- Capacity 24 modules
- Height 4 U (to respect the bending radius of the network cables)
- Max current: 32A
12.4.1 DIN profile rail with front panel
- Cat. No. 0 465 46
- Comprises a front panel, and 15 mm deep rail
equipped with brackets for 19" fixing centre
- IPXXC (front part only)
- Supplied with a 24 modules blanking plate,
screws and cage-nuts
- Rail, fixing brackets and front panel made of steel
- Black RAL 9005 (front panel)
12.4.2 Rear cover
- Cat. No. 0 465 47
- Used with cat. No. 0 465 46 (DIN profile rail
with front panel)
- To be used for heigh current applications
(greater than 50 V)
- Ensure IPXXB
- Compatible with EMC requirements
- Supplied with terminal block for protection
conductors (1X6 to 25 and 8X1.5 to 16 mm2),
12 cable entry glands for Ø 22 mm and fixing screws
- 1.5 mm thick galvanised steel
Catalogue number(s): 0 463 00/06/12/18/19/21/22/23
0 463 28/29/30/33/34/35/41/42/43
Technical data sheet: F01424EN/01 Updated on: 24/10/2014 Created on: 21/02/2012
CONTENTS
31/31
Loading...