Legrand L2EVSE30 User Manual [en, fr, es]

Pour obtenir des informations techniques supplémentaires ou spéciques à une application, appelez au 800-223-4185 ou visitez notre site Internet www. legrand.us/PassAndSeymour. Nous sommes impatients de mettre notre expertise à votre service. Distribué par :

L2EVSE30

Electric Vehicle (EV) Charging Station Station de chargement pour véhicules électriques Estación de carga de vehículo eléctrico (EV)

USER GUIDE / GUIDE DE L’UTILISATEUR / GUÍA DE USUARIO

designed to be better.

For additional technical or application-specific information, call 800-223-4185 or visit our website at www.legrand.us/PassAndSeymour. We’re eager to put our expertise to work for you.

Distributed by:

™

P.O. Box 4822 Syracuse, NY 13221-4822 800-776-4035 www.legrand.us/PassandSeymour

Legrand Canada

570 Applewood Crescent Vaughan, ON, L4K 4B4 Phone: 905.738.9195, Fax: 905.738.9721 www.legrand.ca

designed to be better.

™

www.legrand.us

Table of Contents

Warnings and Notes.................................................. 1

EV Charging Station Mechanical Overview................................ 2

Quick Start........................................................ 2, 3

Status Indicator Display............................................... 3

Delay Timer Indicator Flow ............................................ 4

Features ........................................................... 5

Speciﬁcations ....................................................... 5

Limited One Year Warranty ............................................ 6

Warnings and Notes

Read and understand all instructions before using charging station. The L2EVSE30 Charging Station should be connected to a 40A 208/240VAC, 60Hz grounded branch circuit.

Warning: Improper wiring of any electrical device can cause serious injury

or death. These devices must be installed only by an electrician or other qualiﬁed person in accordance with all appropriate codes and standards. If you are not sure about any part of these instructions, consult a qualiﬁed electrician.

Warning: Shock, ﬁre property damage, personal injury or death may occur if

the charging station is not installed or used in accordance with the instructions and users guide.

Warning: There are no user-serviceable parts contained in this product. Any

attempt to service this product may result in shock, ﬁre, property damage, personal injury or death.

If you have any questions about the use of this product, contact your Legrand technical representative at: 800-223-4185.

INSTRUCTIONS PERTAINING TO THE RISK OF ELECTRIC SHOCK

This product should be supervised when used around children. Do not put ﬁngers into the electric vehicle connector. Do not use this product if the ﬂexible power cord or EV cable is frayed, have

broken insulation, or any other signs of damage. Do not use this product if the enclosure or the EV connector is broken, cracked,

open or show any other indication of damage. CAUTION: To reduce the risk of ﬁre, connect only to a circuit provided with 40

amperes maximum branch circuit overcurrent protection in accordance with the National Electrical Code, ANSI/NFPA 70.

User Guide instructions in French begin on page 7. User Guide instructions in Spanish begin on page 13.

EV Charging Station Mechanical Overview

The charging station is compliant with SAE J1772, and applicable for vehicles ﬁtted with the standard SAE J1772 vehicle charge port and charging systems. The charging station (Figure 1) is comprised of a Charge Connector (a), a NEMA 3R rated enclosure (b), with a status indicator display (c), with a charge cable (d), with a cable hook (e).

The charging station is intended to be hardwired to a dedicated 40A 208/240VAC 60Hz grounded supply circuit by a licensed electrical installer. Installation permits may be required depending on the local codes.

Charge Delay Buttons

Status Indicator (c)

• Ready (Green LED on)

NEMA 3R Rated Enclosure (b)

Charge Connector (a)

• SAEJ1772 compliant

Charge Cable (d)

• Charging (Green LED flashes)

• Fault (Red LED on)

AC Charger Power Switch

Cable Hook (e)

Figure 1

Quick Start

1. Turn on the AC Charger Power Switch located on the right side of the charger.

2. Check to see if your charging station is ready to charge by reviewing the indicator light located in the front panel. Review indicator display status on page 3 of the User Guide.

A solid green light indicates the station is ready to charge. A ﬂashing green light indicates charging in progress. A solid red light indicates that the charger is faulty. Stop using the charger and

contact a service technician.

A ﬂashing red light indicates the charger is recovering from a minor failure.

Stop using the charger until the light turns solid green.

If the indicator lights on your charging station do not match the description above please consult the indicator display status section of the User Guide.

Quick Start (continued)

3. If your charging station is ready to charge, connect the charge connector to the vehicle’s charge port receptacle. While the vehicle is connected, the charge status indicator light will ﬂash. Once the vehicle has been fully charged, the charging will automatically stop. If necessary, charging may be stopped before the vehicle is completely charged.

4. To stop charging, disconnect the vehicle plug and place it back in the charging station (Figure 2).

Delay Timer Indicator Flow

FRONTPANEL DELAYTIMER LED BEHAVIOR DESCRIPTIONDEFINITION

4 LEDs offDelay Timer is not enabled.

2HR

4HR 6HR 8HR

4 LEDs flashing on

2HR LED solid on Delay Timer is set to 2 hours

The charger is ready and the delay timer can be set.

Figure 2

The charging station is equipped with a delayed start option that allows the startup of the charging to be delayed so the vehicle can be charged during off-peak hours. Select desired delay time by pressing the delay timing button. Change time by pressing again. Press stop button to cancel delay. Remove and re-insert charge plug into vehicle to restart charge sequence (see delay indicator chart on page 4).

Status Indicator Display

The charging station has a status indicator display as shown below.

FRONT PANEL LED BEHAVIOR DEFINITIONDESCRIPTION

Power is off.

Off

Solid on

Flashing Charging in process

Solid on

Use the switch on the side of the charger to turn on the power.

Charger is turned on.

Connect the charging cable to start charging.

Charger is faulty.

Please stop using the charger and immediately contact Legrand tech support.

2HR

4HR 6HR 8HR

2HR and 4HR LEDs solid on

2HR, 4HR, and 6HR LEDs solid on

2HR, 4HR, 6HR, and 8HR LEDs solid on

2HR LED flashing on

2HR LED solid on and 4HR LED flashing on

2HR and 4HR LEDs solid on, 6HR LED flashing on

2HR, 4HR, and 6HR LEDs solid on, 8HR LED flashing on

Delay Timer is set to 4 hours

Delay Timer is set to 6 hours

Delay Timer is set to 8 hours

Delay charging is enabled.

Current delay time is less than 2 hours.

Delay charging is enabled.

Current delay time is 2 - 4 hours.

Delay charging is enabled.

Current delay time is 4 - 6 hours.

Delay charging is enabled.

Current delay time is 6 - 8 hours.

Flashing on

Charger is recovering from a minor failure.

Please stop using the charger until the LED turns solid green.

+ 7 hidden pages