Legrand E77378WHT3WB User Manual

E77378WHT3WB

Modular Tele-Power Pole

INSTALLATION INSTRUCTIONS

Wiremold Electrical Systems conform to and should
be installed and properly grounded in compliance
with requirements of the current National Electrical
Code, Canadian Electrical Code, or codes
administered by local authorities.

All electrical products may represent possible
shock or fire hazard if improperly installed or used.
Wiremold electrical products are UL listed, made for
interior use only, and should be installed in
conformance with current local and/or the National
Electrical Code.

TELEPHONE CABLES – NO. OF PAIRS 25 4
NO. OF CABLES 30% FILL 3 20

MAX FILL 7 40

The Wiremold Company

U.S. and International:
60 Woodlawn Street • West Hartford, CT 06110
1-800-621-0049 • FAX [phone] • Outside U.S. 860-233-6251
In Canada:
850 Gartshore Street • Fergus, Ontario N1M 2W8
1-800-741-7957 • FAX [phone]

© Copyright 2002 The Wiremold Company All Rights Reserved

42291 – February 2002 – For latest specs visit www.wiremold.com

Consisting of:

E77378WHT3WB-P1 Pole 14'5" [439.42cm]

Entrance End Fitting: Switched Sign Power;
two IG Circuit Connector; Standard Power
Circuit Connector; two connectorized Power
Whips; Mounting Hardware.

F10062 IG Box w/7' [213.36cm] Whip

Two 125V, 15 Amp IG duplex receptacles;
connectorized power whip.

F10063 IG Box w/11' [335.28cm] Whip

Two 125V, 15 Amp IG duplex receptacles;
connectorized power whip.

F10064 Box w/11' [335.28cm] Whip

Two 125V, 15 Amp duplex convenience
receptacles; connectorized power whip.

2 1/4"

[57mm]

1"

[25mm]

1 1/4"

[32mm]

2 5/16"

[59mm]

– CAUTION –

Make sure Power is off

before installing these poles.

4. To power boxes, plug box whip

into corresponding connector
on pole. Match the three pin
whip to the three pin connector.
Match the four pin whips to the
four pin connectors.

1. Attach Pole Brace to pole using 3/8" threaded rod
(not supplied). Secure with appropriate nuts; do not
tighten. Attach Wireduct Bracket to Wireduct. Secure
the opposite end of the threaded rod to the Wireduct
with suitable nuts. For security, double nutting at the
Wireduct end is recommended. Tighten all nuts after
checking that the pole is plumb.

CAUTION: Distance between pole and Wireduct
must not exceed 36".

2. Wireduct Power Wiring.

Run branch circuit conductors through
the Wireduct in an approved manner.
Install the modular whip connector in
1/2" KO in cover of Wireduct nearest
the pole. Working from the inside of the
Wireduct with cover open, hook the
mounting clip on the lower edge of the
hole cut. Tilt and push the receptacle
face into hole cut using a straight blade
screwdriver to compress and seat the
top of mounting clip.

Connect the whip connector pigtail
leads to the branch circuit conductors
using an approved method and carefully
observing color coding. Connect green
ground wire to ground screw in pull box.
Compress locking tabs on power whip
plug and insert into appropriate Wireduct
receptacles. Receptacle and plug with
the orange dot indicate isolated ground.

3. Additional Mounting Method for
securing pole to register counter

Erect pole at desired location. Align for
(4) holes in “U” shaped bracket with
matching holes in the counter vertical
member. Secure with appropriate
fasteners (not provided)