Leggett & Platt Premium Models Series, Prodigy 2.0 Owner's Manual
2.0
owners manual
ENGLISH
SPANISH
FRENCH
Queen
Split King
LPAdjustableBases.com
CONTENTS
CONTENTS
Advisory ...................................................................................................................... 3
Acoustics .................................................................................................................... 5
Fabric Cleaning Information .......................................................................................... 5
Installation ................................................................................................................. 6
Power Down Operation ............................................................................................... 10
Remote Control Function ............................................................................................ 12
Remote Control Programming ..................................................................................... 13
Troubleshooting ......................................................................................................... 16
Accessories ............................................................................................................... 17
1-3-25 Warranty ........................................................................................................ 18
Spanish translation begins on page 20.
La traducción en español inicia en la página 20.
French Canadian translation begins on page 38.
La traduction en Français débute à la page 38.
If adjustable base does not operate or if parts are missing, call:
800-888-3078
Do not contact retail store or dealer.
IMPORTANT INFORMATION
WARNINGWARNING
READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT
FOR OPTIMUM ADJUSTABLE BASE
OPERATION, USE A GROUNDED, ELECTRICAL
SURGE PROTECTION DEVICE (NOT
INCLUDED). FAILURE TO USE A SURGE
PROTECTION DEVICE COULD COMPROMISE
SAFETY OR CAUSE PRODUCT MALFUNCTION.
ELECTRICAL RATING
Electrical components are rated for 100-240V,
50-60Hz, 1.5A.
ELECTRICAL GROUNDING
This product is equipped with a polarized or
grounded electrical power cord. The power cord
will only fit into a grounded, electrical surge
protection device (not included) or a grounded
electrical outlet.
ADVISORY
PRODUCT RATINGS
The base lift motors are not designed for
continuous use. Reliable operation and full
life expectancy will be realized as long as the
lift motor operation does not exceed five (5)
minutes over a forty-five (45) minute period, or
approximately 11% duty cycle. Note: Massage
equipped bases are not designed for continuous,
extended massage operation. Massage systems
are rated for a maximum of 2 hours of use within
any 6 hour period. Any attempt to circumvent
or exceed product ratings will shorten the life
expectancy of the product and may void the
warranty.
The recommended maximum weight (including
mattress) is 700 lb (317 kg) distributed evenly
across the base. This product is not designed
to support or lift this amount in the head
or foot sections alone. Note: Exceeding the
recommended weight restrictions could damage
the base and void the warranty.
WARRANTY WARNING
Do not open any control boxes, motors or
remote control devices (with the exception of
the remote control and power down box battery
compartments). The product warranty will be
void if these components are tampered with. Do
not attempt to alter component wiring or adjust
or modify the structure of the product in any
way or the warranty will be void. Any repair or
replacement of base parts must be performed by
authorized personnel.
LUBRICATION
This product is designed to be maintenance free.
The lift motors are permanently lubricated and
sealed—no additional lubrication is required.
Do not apply lubricant to lift motor lead screws
or any nylon nuts or the base may inadvertently
creep downward from the elevated position.
For best performance, consumers should enter
and exit the adjustable base with the base in the
flat (horizontal) position. Avoid placing entire
weight on head or foot section of the base,
including when in the raised position.
STAND ON BASE AT ANY TIME.
UL (Underwriters Laboratories) recognized
components.
CFR 1633 approved for use with most
mattresses.
Assembled in USA.
DO NOT
Prodigy™ 2.0 Adjustable Base Owners Manual 99301584-c
3
ADVISORY
IMPORTANT INFORMATION
READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT
SMALL CHILDREN / PETS WARNING
After the base is unboxed, immediately dispose
of packaging material as it can smother small
children and pets. To avoid injury, children or
pets should not be allowed to play under or on
the base. Children should not operate this base
without adult supervision.
PACEMAKER WARNING
This product produces a vibrating sensation.
It is possible that individuals with heart-assist
pacemakers may experience a sensation similar
to exercise. Consult physician for complete
information.
HOSPITAL USE DISCLAIMER
This base is designed for in-home use only. It
is not approved for hospital use and does not
comply with hospital standards. Do not use this
base with tent type oxygen therapy equipment, or
use near explosive gases.
SERVICE REQUIREMENTS
Service technicians are not responsible for
moving furniture, removing headboards and
footboards or any items required to perform
maintenance on the base. In the event the
technician is unable to perform service due
to lack of accessibility, the service call will
be billed to the purchaser and the service will
have to be rescheduled.
FCC COMPLIANCE
The equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference when the equipment
is operated in a residential environment. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to radio
or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment
and receiver.
- Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
This device complies with Part 15 of the FCC
rules. Operation is subject to the following
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
Prodigy™ 2.0 Adjustable Base Owners Manual 99301584-c
4
FCC Caution: Any changes or modifications not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate this equipment.
Radio Frequency = 2.4GHz.
ACOUSTICS
LIFTING/LOWERING MECHANISMS
The lift/lower feature will emit a minimal
humming sound during operation. This is normal.
During operation, the lift arm wheels make contact
with the platform support of the base. This applies
slight tension on the moving components and
resonance is reduced to a minimum level. If
excessive noise or vibration is experienced, reverse
the movement action (up or down) of the base with
the remote control. This should realign the base’s
activating mechanisms to the proper operational
position.
MASSAGE OPERATION
The massage feature will emit a minimal tone
during operation. This is normal. When the
massage level is increased, motor resonance will
intensify accordingly.
FABRIC CLEANING INFORMATION
LOCATION ENVIRONMENT
The level of sound experienced during operation
is directly related to the location environment. For
example, when a base is located on a hardwood
floor with the massage feature in operation, a
vibrating tone will be audible. To minimize this
resonance, place a piece of carpet, or rubber
caster cups, under each leg or caster of the base.
It is possible to experience vibration or noise from
the headboard brackets, headboards or footboards
if mounting bolts are not firmly tightened.
Spot clean only with water based shampoo
or foam upholstery cleaner. Pretest a small,
inconspicuous area before proceeding. Do not
over wet. Do not use solvents to spot clean.
Pile fabrics may require brushing with a nonmetallic, stiff bristle brush to restore appearance.
Hot water extraction or steam cleaning is not a
recommended cleaning method.
To prevent overall soiling, frequent vacuuming
or light brushing with a non-metallic stiff bristle
brush to remove dust and grime is recommended.
When cleaning a spill, blot immediately to remove
spilled material. Clean spots or stains from the
outside to the middle of the affected area to
prevent circling. Use a professional furniture
cleaning service when an overall soiled condition
is apparent.
Prodigy™ 2.0 Adjustable Base Owners Manual 99301584-c
5
INSTALLATION
For installation and setup, complete the following procedures, in the order indicated below
and on the following pages:
STEP 1
Before discarding any packing materials,
check the adjustable base shipping carton
and verify the following items are
included:
t#FE-FHT
t3FNPUF$POUSPMX"""CBUUFSJFT
t3FNPUF$POUSPM)PMEFS
t1PXFS4VQQMZ
feed cord, and electrical power cord)
t%VBM4ZOD$BCMF(split sizes only)
t.BUUSFTT3FUBJOFS
(includes power brick, electrical
t8BSSBOUZ"DUJWBUJPO$BSE
t2VJDL4FUVQ(VJEF
LEG
(4 pieces)
WARRANTY
ACTIVATION CARD
DUAL SYNC CABLE
(split sizes only)
QUICK SETUP GUIDE
MATTRESS
RETAINER
REMOTE CONTROL
w/ 3 AAA batteries
REMOTE CONTROL HOLDER
(shown with remote control)
Prodigy™ 2.0 Adjustable Base Owners Manual 99301584-c
6
POWER SUPPLY (power brick, electrical feed
cord, and electrical power cord)
factory attached to base, no assembly
required
INSTALLATIONINSTALLATION
WARNINGWARNING
CAUTIONCAUTION
WARNINGWARNING
STEP 2
Remove the hardware box. Cut zip-tie and remove
mattress retainer.
STEP 3
Install (4) legs into the base frame. Simply screw each leg
into a tapped hole at the corner of the base frame (FIGURE 1).
Push pin in to adjust leg height (achieve leg height of 6 inches
to 10 inches).
FIGURE 1
LEGS – SCREW
INTO TAPPED
HOLE AT EACH
CORNER
PUSH PIN IN
TO ADJUST LEG
HEIGHT
(6 INCHES TO
10 INCHES)
AT LEAST TWO PEOPLE ARE
RECOMMENDED FOR HANDLING AND
MOVING ADJUSTABLE BASE.
CAUTION
DO NOT ATTEMPT TO SCREW
LEGS INTO ANY OTHER INSERTS.
THIS WILL DAMAGE PRODUCT.
STEP 4
Carefully lift the adjustable base from the shipping carton,
keeping the unit top-side-down. Uncoil and extend out
power cord from base.
POWER CORDS MUST NOT INTERFERE WITH
ANY ADJUSTABLE BASE MECHANISMS.
Prodigy™ 2.0 Adjustable Base Owners Manual 99301584-c
7
INSTALLATION
STEP 5
Remove the plastic packaging from the base frame. Carefully rotate the
adjustable base over to position the base so it is resting on its legs (FIGURE 2).
FIGURE 2
4-PORT CHARGING HUB
HEAD END
OF BASE
STEP 6
Plug electrical power cord into a working, grounded electrical outlet.
Note: An electrical surge protection device is recommended (not included).
STEP 7
Install batteries in remote control (3-AAA, included) (FIGURE 3). Note:
Make sure batteries are properly oriented. Briefl y activate all functions of the
base with the remote control to verify all features are in working order. If
base does not operate, refer to the Troubleshooting section of this manual.
(located on each side of
base, for charging low-
voltage devices only)
FIGURE 3
POSITIVE (+)
END
TAB
BATTERY
COMPARTMENT
DOOR
PRESS IN ON TAB AND LIFT
OUT TO REMOVE BATTERY
COMPARTMENT DOOR.
INSERT TABS IN TAB SLOTS
AND SNAP IN TO REPLACE.
STEP 8
Return base to the level position.
POSITIVE (+)
END
Prodigy™ 2.0 Adjustable Base Owners Manual 99301584-c
8
INSTALLATION
MATTRESS RETAINER INSTALLATION (OPTIONAL)
Mattress is equipped with a MicroHook™ system
to captivate the mattress (FIGURE 4), but if
desired a mattress retainer can also be used. If
installing a mattress retainer, proceed to Step 9.
If not installing a mattress retainer, proceed to
Step 10.
IMPORTANT!
THIS PRODUCT SHOULD NOT BE USED WITH
EITHER A DUST RUFFLE OR A MATTRESS
ENCASEMENT. IF EITHER A DUST RUFFLE
OR MATTRESS ENCASEMENT IS NEEDED,
THEN A MATTRESS RETAINER BAR IS
REQUIRED.
FIGURE 4
Micro-Hook™
SYSTEM
FOOT END OF BASE
Micro-Hook™
DETAIL
STEP 9
Install mattress retainer at the foot end of the adjustable base as follows:
a. Locate grommeted holes at foot end of base.
b. Place mattress retainer ends into grommeted holes in top surface
of adjustable base (FIGURE 5). Press down until horizontal retainer
section is fl ush against base.
FIGURE 5
MATTRESS
RETAINER
STEP 10
Install mattress on adjustable base.
Typical Prodigy™ 2.0 adjustable base installation is now complete.
Prodigy™ 2.0 Adjustable Base Owners Manual 99301584-c
9
POWER DOWN OPERATION
To lower the base to the fl a t position during an electrical power outage, complete the following procedure:
STEP 1
Verify power is unplugged from electrical power source.
STEP 2
Locate (1) power brick (FIGURE 6) and (2) 9 volt batteries (not
included).
FIGURE 6
POWER
BRICK
STEP 3
Install (2) 9 volt batteries in power brick (FIGURE 7).
FIGURE 7
BATTERY
COMPARTMENT DOOR
(push down and slide off
to remove)
10
UNDERSIDE OF
POWER BRICK
INSTALL (2) 9 VOLT BATTERIES
*BATTERIES NOT INCLUDED
Prodigy™ 2.0 Adjustable Base Owners Manual 99301584-c
POWER DOWN OPERATION
STEP 4
Press the head down button on the remote control until the head
section is fl at, then press the foot down button on the remote
control until the foot section is fl at (FIGURE 8).
FIGURE 8
HEAD
DOWN
BUTTON
FOOT
DOWN
BUTTON
STEP 5
Remove two (2) 9 volt batteries from power brick. Plug power
cord back into electrical power source (FIGURE 9). When power is
restored from outage, base is ready to resume normal operation.
FIGURE 9
Prodigy™ 2.0 Adjustable Base Owners Manual 99301584-c
11
REMOTE CONTROL FUNCTION
Press and hold to raise head to the
SNORE BUTTON
preprogrammed position. Head will
automatically lower to fl at after 15
minutes.
*To program a position, adjust base to
desired position, press and hold the set
button until the massage motors and
underbed light turn on and off, then
press and hold the Snore button until
the massage motors turn on and off.
HEAD UP/DOWN BUTTON
Press and hold to raise or lower the head
section.
PILLOW TILT UP/DOWN BUTTON
Press and hold to raise or lower the
pillow tilt section.
SET BUTTON
Press and hold to program M1, M2 and
Snore presets.
HEAD MASSAGE UP/DOWN BUTTON
Press to increase or decrease massage
intensity. Massage has 3 speeds:
Low, medium and high. Massage will
automatically shut off after 15 minutes.
MASSAGE ON/OFF BUTTON
Press “on” to turn both massage motors
on. Press “off” to turn both massage
motors off.
FLAT BUTTON
Press and hold to lower the base to the
level position.
UNDERBED LIGHT BUTTON
Press to turn underbed light on. Press
again to turn underbed light off.
LOCK BUTTON
Press to lock remote control. Press again
to unlock remote control.
FOOT UP/DOWN BUTTON
Press and hold to raise or lower the foot
section.
M1 BUTTON
Press and hold to adjust base to the
programmed position.
*To program a position, adjust base to
desired position, press and hold the set
button until the massage motors and
underbed light turn on and off, then
press and hold the M1 button until the
massage motors turn on and off.
M2 BUTTON
Press and hold to adjust base to the
programmed position.
*To program a position, adjust base to
desired position, press and hold the set
button until the massage motors and
underbed light turn on and off, then
press and hold the M2 button until the
massage motors turn on and off.
FOOT MASSAGE UP/DOWN BUTTON
Press to increase or decrease massage
intensity. Massage has 3 speeds:
Low, medium and high. Massage will
automatically shut off after 15 minutes.
NOTE
REMOTE CONTROL REQUIRES THREE (3) AAA SIZE BATTERIES (INCLUDED).
PRESS & HOLD TO ONE TOUCH
Note: If using 2 remotes to operate 1 or more bases, both remotes must be set to the same “press & hold” or “press & touch” mode.
To change remote control functions from “press and hold” to “one touch” (“one touch” = press and release), simultaneously press
the HEAD MASSAGE DOWN and FOOT MASSAGE DOWN buttons for 5 seconds. The massage motor
and off confi rming the change. Your base is now set to “one touch.”
When in “one touch” mode:
M1, M2, and Snore buttons
Press and release (one touch) button. Base will adjust to the programmed position. Press any other button to stop the base during movement.
Flat button
Press and release (one touch) button. Base will shut off massage motor, if active, and adjust base to level position. Press any other
button to stop the base during movement.
To revert back to factory settings, simultaneously press and hold the SET button and the FLAT button for 5 seconds. The massage
motor will turn on and off confi rming the change. Your base is now set to factory settings. Note: M1, M2, and Snore positions will
revert to factory preprogrammed positions.
12
Prodigy™ 2.0 Adjustable Base Owners Manual 99301584-c
and underbed light will turn on
REMOTE CONTROL PROGRAMMING
(
Program One Remote to Operate One Base - perform the
following numbered procedure.
STEP 1
Unplug the adjustable base electrical power
cord from power source. Wait 30 seconds, then
plug back in.
STEP 2
Remove the battery compartment door from the
remote control (FIGURE 10).
FIGURE 10
LEARN
SWITCH
BATTERY
COMPARTMENT
DOOR
1 remote control - 1 base)
FIGURE 11
LEARN
BUTTON
CONTROL
BOX
STEP 3
Position base on its side. Locate the control
box, attached to the underside of the base
(FIGURE 11).
STEP 4
Using a pointed object, push the learn button
in two times in rapid succession (FIGURE 11).
The underbed lighting will come on.
STEP 5
On the remote control, press and hold the learn
switch (FIGURE 10)
goes off.
until the underbed lighting
STEP 6
Operate remote control to verify programming.
One remote control is now programmed to
operate one base.
Prodigy™ 2.0 Adjustable Base Owners Manual 99301584-c
13
REMOTE CONTROL PROGRAMMING (1 or 2 remote controls - 2 bases)
Program One Remote to Operate Two Bases (Tandem Syncing)
- perform the following numbered procedure. Note: Make
sure both remotes are in “press & hold” mode and both bases
are fl at before beginning procedure. IF USING 2 REMOTES TO
OPERATE 1 OR MORE BASES, BOTH REMOTES MUST BE IN THE
SAME “PRESS & HOLD” OR “PRESS & RELEASE” MODE FOR FLAT OR
PROGRAMMABLE BUTTONS TO FUNCTION.
BASE 1
OR
STEP 1
Plug both adjustable bases into electrical power source.
Operate both remote controls to verify each remote
functions properly with its respective base. NOTE: see
1-to-1 programming procedure if bases do not operate.
Using remote controls, adjust both bases to fl at position.
STEP 2
UNPLUG both bases from electrical power outlet.
STEP 3
Choose base 1 remote. Retain base 2 remote control as a
spare or use if 2 remotes are desired to operate both bases.
STEP 4
Position both bases on their sides, in close proximity
to each other. CAUTION: AT LEAST TWO PEOPLE
ARE RECOMMENDED FOR HANDLING AND MOVING
ADJUSTABLE BASE.
STEP 5
Locate dual sync cable (FIGURE 12).
FIGURE 12
DUAL SYNC
CABLE
REMOTE 1 REMOTE 2
FIGURE 14
MALE
PLUG
FEMALE
PLUG
FIGURE 15
CONTROL
BOX
FEMALE
PLUG
BASE 2
DUAL
SYNC
CABLE
CONTROL
BOX
CABLE
REMOVED
FROM
CONTROL
BOX
STEP 6
On base 1, unplug the existing cable from the control box
(FIGURE 13). Insert one male plug of dual sync cable into
the control box (FIGURE 14). Insert removed cable into
the female plug of the dual sync cable (FIGURE 15).
FIGURE 13
CONTROL
BOX
14
EXISTING
CABLE
Prodigy™ 2.0 Adjustable Base Owners Manual 99301584-c
STEP 7
Repeat Step 6 with base 2, using the remaining male and
female plugs of the dual sync cable.
STEP 8
Turn both bases over so they are resting on their legs.
CAUTION: MAKE SURE CABLE IS CLEAR OF BASE AND FREE
OF ANY PINCH POINTS.
STEP 9
Plug both bases into electrical power source.
STEP 10
Operate both bases with the remote control. NOTE: If
bases do not operate in unison with the remote, verify
dual sync cable connections are fully seated in both MFP
ports. Unplug both bases, wait 10 seconds, then plug
them back in.
REMOTE CONTROL PROGRAMMING (separating 2 bases)
Separate Two Bases - for independent adjustable base
movement, perform the following numbered procedure.
STEP 1
Unplug both bases from electrical power outlet. Position
both bases on their sides, in close proximity to each other.
CAUTION: AT LEAST TWO PEOPLE ARE RECOMMENDED FOR
HANDLING AND MOVING ADJUSTABLE BASE.
STEP 2
Locate control box on both bases. Locate dual sync cable
(FIGURE 12).
STEP 3
On each base, remove the male plug of the dual sync
cable from the control box (FIGURE 16).
STEP 4
On each base, remove the cable from the female plug
of the dual sync cable and plug it into the control box
(FIGURES 16 and 17).
FIGURE 16
MALE
CONTROL
BOX
PLUG
FEMALE
PLUG
CABLE
REMOVED
FROM
CONTROL
BOX
REMOTE 1
REMOTE 1
FIGURE 18
LEARN
BUTTON
BASE 1
BASE 2
CONTROL
BOX
STEP 7
On remote control 1, press and hold the learn switch
(FIGURE 19) until the underbed lighting goes off.
FIGURE 17
CABLE
REMOVED
FROM
FEMALE
PLUG
CONTROL
BOX
STEP 5
Plug base 1 into electrical power outlet. Using a pointed
object, push the learn button in two times in rapid succession
(FIGURE 18). The underbed lighting will come on.
STEP 6
Remove the battery compartment door from the both
remote controls.
FIGURE 19
LEARN
SWITCH
BATTERY
COMPARTMENT
DOOR
STEP 8
Repeat Steps 5, 6 & 7 with base 2 and remote control 2.
STEP 9
Turn both bases over so they are resting on their legs.
CAUTION: AT LEAST TWO PEOPLE ARE RECOMMENDED FOR
HANDLING AND MOVING ADJUSTABLE BASE.
Independent remote control operation is now
restored (remote control 1 operating base 1; remote
control 2 operating base 2).
Prodigy™ 2.0 Adjustable Base Owners Manual 99301584-c
15
TROUBLESHOOTING
If the adjustable base fails to operate, investigate the symptoms and possible solutions
provided in the chart below:
SYMPTOM
Remote control illuminates and appears to be
operable, but will not activate base.
No features of the base will activate.
Remote control will not illuminate.
Head or foot section will elevate, but will not
return to the horizontal (flat) position.
SOLUTION
t7FSJGZQPXFSDPSEJTQMVHHFEJOUPBXPSLJOHHSPVOEFE
electrical outlet. A grounded, electrical surge protection
device is recommended. Test outlet by plugging in
another working appliance.
t *GUIFCBTFXBTPQFSBUFEPWFSUIFSBUFEEVUZDZDMF
thermal switch opens. Wait 30 minutes before trying
to operate the base. Once the base resumes normal
operation, do not exceed the duty cycle.
t1SPHSBNUIFSFNPUFDPOUSPMTFFRemote Control
Programming section of this manual for programming
procedures).
t6OQMVHQPXFSDPSEXBJUTFDPOETBOEQMVHJOUP
reset electronic components.
t&MFDUSJDBMDJSDVJUCSFBLFSNBZCFUSJQQFE$IFDL
electrical service breaker box to verify.
t%FGFDUJWFTVSHFQSPUFDUJPOEFWJDFPSFMFDUSJDBMPVUMFU
Test outlet by plugging in another working appliance.
t3FQMBDFCBUUFSJFTJOUIFSFNPUFDPOUSPM
t#BTFNFDIBOJTNNBZCFPCTUSVDUFE&MFWBUFCBTFBOE
check for obstruction. Remove obstruction.
t )FBETFDUJPONBZCFUPPDMPTFUPUIFXBMM
Excessive massage motor noise.
16
Prodigy™ 2.0 Adjustable Base Owners Manual 99301584-c
t*GCBTFJTMPDBUFEPOIBSETVSGBDFnPPSJOHQMBDFDBSQFU
pieces or rubber caster cups under each leg or caster
of the base. (See accessory sheet for rubber caster cup
order information.)
t&MFWBUFUIFIFBEPSGPPUTFDUJPOBTIPSUEJTUBODFXJUI
the remote control) to realign the lift/lower mechanisms
with the bed support platform.
t7FSJGZUIBUUIFCBTFJTOPUQPTJUJPOFEBHBJOTUBXBMM
nightstand, or other object that may cause vibration or
noise.
t*GCBTFJTJOTUBMMFEPWFSBCFEGSBNFWFSJGZNBTTBHF
motors are not causing bed frame (or bed frame
components) to vibrate.
ACCESSORIES
OPTIONAL EQUIPMENT
Contact customer service toll free (800-888-3078) to order the accessories indicated in the chart
below.
ACCESSORY DESCRIPTION
Head Board Brackets-TXL
Head Board Brackets-FXL/Q
Push-in Locking Casters
Bed Link Kit (connects two bases together)
Swing-away Hinges (headboard required for use,
cannot be used with bed straps)
(set of 4)
CODE IMAGE
4B8808
4B8809
4B1806
4B7410
4B1209
Prodigy™ 2.0 Adjustable Base Owners Manual 99301584-c
17
Loading...