Leggett & Platt P-2000 User Manual

MODEL NO

P-2000

Platinum SeriesPlatinum Series

Platinum Series

Platinum SeriesPlatinum Series

20002000

2000

20002000

ADJUSTABLE BED

WITH WALLHUGGER® ACTION

• Introduction

• Installation

• Operation

• Trouble Shooting

• Warranty

RETAIN FOR FUTURE
REFERENCE

Manual Part Number:

99300487

1-04

SERIAL NO:

WARNINGS

WARNING! IMPORTANT SAFETY INSTRUCTIONS

PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE USING THIS PRODUCT.

Your Adjustable Bed has been totally engineered to provide you with reliability of operation and the strength
you deserve. The manufacturer has given each bed a thorough inspection and testing prior to shipment.
The utmost in comfort and safety has been provided for you. This bed is for HOME use only. It is NOT
designed for hospital use and was not designed to meet hospital standards. Do not use bed with TENT
TYPE oxygen therapy equipment, or near explosive gases.

GROUNDING SAFETY

This Adjustable Bed has a grounded plug (two flat blades and one round pin) as a safety feature to reduce
the risk of electric shock. The plug will only fit into a grounded outlet one way. If this plug does not fit into your
outlet, contact a qualified electrician and have them install a properly grounded outlet. NEVER REMOVE
THE GROUNDING PIN OR ALTER THE PLUG IN ANY WAY. Unauthorized modifications could void the
electrical portion of your warranty. The use of adapters is not recommended unless the outlet is checked
by a qualified electrician to ensure the proper grounding of the adapter. Failure to use a properly grounded
outlet for this product will compromise this important grounding safety feature and may result in electrical
shock, electrical fire, or faulty operation of the product. FOR BEST RESULTS, YOUR BED SHOULD BE

PLUGGED INTO A SURGE PROTECTOR (not supplied with this adjustable bed).

WARNING!

Do not open control box, motors or hand controls (with the exception of the battery compartment). The

warranty is void if these units are tampered with. Any repair or replacement of adjustable bed parts must
be implemented by an authorized person.

IMPORTANT SAFETY FEATURE

This Adjustable Bed is equipped with a special locking caster for your safety. In order to prevent the movement
of this product, all four casters should be locked in position. This may be accomplished by pushing down
the safety latch on the caster. To resume mobility of the product, lift up on the safety latch. You are strongly
encouraged to place rubber caster cups or carpet squares under the casters in addition to locking them in
place if the product is positioned on a hard surface floor such as hardwood, tile or linoleum. Although your
casters are locked and will not roll, they may slide. Note: To avoid damage to flooring, casters must

be installed before operating the bed. Failure to attach casters my void warranty.

1

WARNINGS

For best performance, consumers should enter and exit the adjustable bed with the bed in the flat or
down position.

A note to consumers with pacemakers: As with any product that produces a vibrating motion, it is
possible that some pacemakers may interpret this motion as a false sense of movement and/or exercise.
This may or may not affect your pacemaker. If you have any concerns, please consult your physician.

WEIGHT RESTRICTIONS:

The recommended weight restrictions on our adjustable beds are as follows:

Twin 300

Full 375

Queen 425

The bed will structurally support the recommended weights when distributed uniformly across the entire
bed. This product is not desighed to support or lift this amount of weight in the head or foot sections alone.

DO NOT SIT ON THE HEAD OR FOOT SECTION WHILE IT IS IN THE RAISED POSITION.

Note: Exceeding the recommended weight restrictions could damage your adjustable bed
and void your warranty.

RADIIO FREQUENCY IS 310 MHz.

WARNING: The transmitter and the receiver of the wireless control system have been tested and comply

with FCC and DOC/MDC rules. Changes or modifications not expressly approved be the party responsible
for compliance could void user’s authority to operate the equipment.

2

INSTALLATION

STEP 1

Remove and discard the packing materials from the bottom of the base unit. You will see the mattress
retainer bracket and headboard brackets attached to the side rail of the bed. Remove these items and
set aside for the moment. Remove bagged parts and the power cord from the underside of the bed.

MATTRESS RETAINER BRACKET

STEP 2

Insert casters into the caster sockets at the
bottom of each leg. If necessary, strike the
center of the caster lightly with a hammer.

NOTE: To avoid damage to flooring,
casters must be installed before
operating the bed. Failure to attach
casters may void warranty.

HEADBOARD BRACKET

3