Legacy Classic 2830-4105K User Manual
ASSEMBLY INSTRUCTIONS:
2830-4105/4115/4901 BED
Thank you for purchasing this quality product. Before beginning, please check the packing material carefully for
small parts which may have come loose inside the carton during shipping. Please do not discard any packing
material until all parts have been located. If any parts are missing, please contact your dealer for prompt
replacement.
Parts & Hardware List:
A
HEADBOARD
B
FOOTBOARD
C
BUN FOOT
D
FINIAL
HARDWARE LIST
1
BOLT
2
SPRING WASHER
3
FLAT WASHER
PARTS LIST
5/16"*1"
5/16"
5/16"*16*1.2mm
A
Q'TY
1 PC
1 PC
2 PCS
2 PCS
Q'TY
8 PCS
8 PCS
8 PCS
E
BED RAIL
F
SLAT
G
SUPPORT LEG
HARDWARE LIST
4
WRENCH
5
WOOD SCREW
4
1
2
3
PARTS LIST
87*12mm
8*1-1/4"
A
Q'TY
2 PCS
3 PCS
3 PCS
Q'TY
1 PC
6 PCS
5
F
F
D
E
G
C
Step 2
B
C
E
B
Step 3
D
B
Step 4
Assembly Procedures:
Step 1: Lay out all parts and hardware. Make sure the quantity of each is correct and the feet are free of stain,
staples, screws and nails.
Step 2: Assemble the bun feet (C) to the footboard (B) as shown.
Step 3: Assemble the bed rails (E) to headboard outer holes (A) and footboard (B) as shown.
Step 4: Assemble the support legs (G) to the slats (F), then assemble the slats to the bed rails as shown.
Assemble the finials (D) to the footboard (B) as shown.
Caution: Over-tighting screws or bolts may result in damage. It is suggested that at least two people work together
for this assembly process to avoid injury. Following assembly, the furniture should be cleaned with a quality,
non-silicone furniture polish on a clean, soft cloth.
www.legacyclassickids.com
ASSEMBLY INSTRUCTIONS:
2830-4105 HEADBOARD
Thank you for purchasing this quality product. Before beginning, please check the packing material carefully for
small parts which may have come loose inside the carton during shipping. Please do not discard any packing
material until all parts have been located. If any parts are missing, please contact your dealer for prompt
replacement.
Parts & Hardware List:
PARTS LIST
A
HEADBOARD
BOTTOM STRETCHER
B
C
RIGHT POST LEG
HARDWARE LIST
1
SHORT BOLT
2
SPRING WASHER
3
FLAT WASHER
PARTS LIST
HARDWARE LIST
87*12mm
5/16"*2"
10*40mm
Q'TY
1 PC
2 PCS
Q'TY
1 PC
2 PCS
4 PCS
5/16"*1-1/2"
5/16"
5/16"*19*2mm
Q'TY
1 PC
1 PC
1 PC
Q'TY
6 PCS
8 PCS
8 PCS
D
LEFT POST LEG
E
FINIAL
4
WRENCH
5
LONG BOLT
6
WOOD DOWEL
4
E
1
4
5
D
2
3
2
3
E
A
6
A
D
B
C
Step 2
Step 3
C
Step 4
Assembly Procedures:
Step 1: Lay out all parts and hardware. Make sure the quantity of each is correct and the feet are free of stain,
staples, screws and nails.
Step 2:
Step 3: Assemble the
Step 4: Turn the entire Headboard upright.
Assemble the right & left support legs (C&D) to stretcher (B) as shown.
right & left
support legs (
C&D
) to the headboard(A) directly as shown.
Assemble the finials (E) to the headboard (A) as shown.
The Headboard is now ready to assemble with the footboard and rails.
These assembly instructions are a separate sheet found inside the carton.
Caution: Over-tighting screws or bolts may result in damage. It is suggested that at least two people work together
for this assembly process to avoid injury. Following assembly, the furniture should be cleaned with a quality,
non-silicone furniture polish on a clean, soft cloth.
www.legacyclassickids.com
Loading...